Add a VLAN on a bridge port, delete it and make sure the PVID VLAN is
not affected.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running the test on the Spectrum ASIC the generated packets are
counted on the ingress filter and injected back to the pipeline because
of the 'pass' action. The router block then drops the packets due to
checksum error, as the test generates packets with zero checksum.
When running the test on an emulator that is not as strict about
checksum errors the test fails since packets are counted twice. Once by
the emulated ASIC on its ingress filter and again by the kernel as the
emulator does not perform checksum validation and allows the packets to
be trapped by a matching host route.
Fix this by changing the action to 'drop', which will prevent the packet
from continuing further in the pipeline to the router block.
For veth pairs this change is essentially a NOP given packets are only
processed once (by the kernel).
Fixes: a0b61f3d8e ("selftests: forwarding: vxlan_bridge_1d: Add an ECN decap test")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patches made it possible to setup VLAN devices with VID 1 over
mlxsw ports. Verify this functionality actually works by conducting a
simple router test over VID 1.
Adding this test as a generic test since it can be run using veth pairs
and it can also be useful for other physical devices where VID 1 was
considered reserved (knowingly or not).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce basic testing for both IPv4 and IPv6 multicast. The test creates
an (S,G) type route, sends traffic and verifies traffic arrives when the
route is present and then verifies traffic does not arrive after deleting
the route.
This test requires smcroute - https://github.com/troglobit/smcroute which
is a tool that allows creation of static multicast routes.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using VLAN-aware bridges with VXLAN, the VLAN that is mapped to the
VNI of the VXLAN device is that which is configured as "pvid untagged"
on the corresponding bridge port.
When these flags are toggled or when the VLAN is deleted entirely,
remote hosts should not be able to receive packets from the VTEP.
Add a test case for above mentioned scenarios.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test is very similar to its VLAN-unaware counterpart
(vxlan_bridge_1d.sh), but instead of using multiple VLAN-unaware
bridges, a single VLAN-aware bridge is used with multiple VLANs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test which checks that the VxLAN driver can learn FDB entries and
that these entries are correctly deleted and aged-out.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simple wrapper reruns the VXLAN ping test with a port number of
8472.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that when decapsulating from VXLAN, the values of inner and outer
TOS are handled appropriately. Because VXLAN driver on its own won't
produce the arbitrary TOS combinations necessary to test this feature,
simply open-code a single ICMP packet and have mausezahn assemble it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that ECN bits in the VXLAN envelope are correctly deduced from the
overlay packet.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that TOS is inherited from the tunneled packet into the envelope as
configured at the VXLAN device.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tests whether TTL of VXLAN envelope packets is properly set based
on the device configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ordering of the topology creation can have impact on whether a
driver is successful in offloading VXLAN. Therefore add a pseudo-test
that reshuffles bits of the topology, and then reruns the same suite of
tests again to make sure that the new setup is supported as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that when sending traffic to a learned MAC address, the traffic is
forwarded accurately only to the right endpoint.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that when sending traffic to an unlearned MAC address, the traffic
is flooded to both remote VXLAN endpoints.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test end-to-end reachability between local and remote endpoints.
Note that because learning is disabled on the VXLAN device, the ICMP
requests will end up being flooded to all remotes.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This skeleton sets up a topology with three VXLAN endpoints: one
"local", possibly offloaded, and two "remote", formed using veth pairs
and likely purely software bridges. The "local" endpoint is connected to
host systems by a VLAN-unaware bridge.
Since VXLAN tunnels must be unique per namespace, each of the "remote"
endpoints is in its own namespace. H3 forms the bridge between the three
domains.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Such a function will be useful for counting malformed packets in the ECN
decap test.
To that end, introduce a common handler for handling stat-fetching, and
reuse it in link_stats_tx_packets_get() and link_stats_rx_errors_get().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the ping routine more generic by allowing passing arbitrary ping
command-line arguments.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have ping_test() recognize an optional argument with a description of
the test. This is handy if there are several ping test, to make it clear
which is which.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to run a certain command inside another network namespace, it's
possible to use "ip netns exec ns command". However then one can't use
functions defined in lib.sh or a test suite.
One option is to do "ip netns exec ns bash -c command", provided that
all functions that one wishes to use (and their dependencies) are
published using "export -f". That may not be practical.
Therefore, introduce a helper in_ns(), which wraps a given command in a
boilerplate of "ip netns exec" and "source lib.sh", thus making all
library functions available. (Custom functions that a script wishes to
run within a namespace still need to be exported.)
Because quotes in "$@" aren't recognized in heredoc, hand-expand the
array in an explicit for loop, leveraging printf %q to handle proper
quoting.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far the case of NUM_NETIFS of 0 has not been interesting. However if
one wishes to reuse the lib.sh routines in a setup of a separate
namespace, being able to import like this is handy.
Therefore replace the {1..$NUM_NETIFS} references, which cause iteration
over 1 and 0, with an explicit for loop like we do in setup_wait() and
tc_offload_check(), so that for NUM_NETIFS of 0 no iteration is done.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Immediately after mlxsw module is probed and lldpad started, added APP
entries are briefly in "unknown" state before becoming "pending". That's
the state that lldpad_app_wait_set() typically sees, and since there are
no pending entries at that time, it bails out. However the entries have
not been pushed to the kernel yet at that point, and thus the test case
fails.
Fix by waiting for both unknown and pending entries to disappear before
proceeding.
Fixes: d159261f36 ("selftests: mlxsw: Add test for trust-DSCP")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test adds an fdb entry with the sticky flag and sends traffic from
a different port with the same mac as a source address expecting the entry
to not change ports if the flag is operating correctly.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some selftests need to tweak MTU of an interface, and naturally should
at teardown restore the MTU back to the original value. Add two
functions to facilitate this MTU handling: mtu_set() to change MTU
value, and mtu_reset() to change it back to what it was before.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gre_multipath test was using egress vlan_id matching on flows, for the
purpose of collecting next-hops statistics, later to be compared
against configured weights.
As matching on vlan_id on egress direction is not supported on all HW
devices, change the match criteria to use destination IP.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dscp_capture_install() and dscp_capture_uninstall() are going to be
useful for a test added by a following patch, move them therefore to
lib.sh together with related helpers.
While doing so, change the rule preference from mere DSCP value to
DSCP+100 in order to support adding captures of packets with DSCP of 0.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function lldpad_wait() will be useful for a test added by a
following patch. Likewise would the "sleep 5" with its extensive
comment.
Therefore move lldpad_wait() to lib.sh in order to allow reuse. Rename
it to lldpad_app_wait_set() to recognize that what this is intended to
wait on are the pending APP sets.
For the sleeping, add a function lldpad_app_wait_del(). That will serve
to hold the related explanatory comment (which edit for clarity), and as
a token in the caller to identify the sites where this sort of waiting
takes place. That will serve when/if a better way to handle this
business is found.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tests mirror-to-gretap when an underlay packet path includes a team
device which is not in loadbalance mode, but in LACP mode. The test
manipulates LAG membership to achieve changes in txability, thus making
sure that a driver that offloads mirror-to-gretap doesn't just consider
upness of a device.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test for "tc action mirred egress mirror" that mirrors to gretap when
the underlay route points at a VLAN-aware bridge (802.1q), and the
traffic egresses the bridge through a team device. Test upping and
downing individual team device slaves and verify the traffic flows as
expected.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of relying on "arping" being installed everywhere under that
name, introduce a variable $ARPING like the other tools do.
Convert an existing test, mirror_gre_vlan_bridge_1q.sh to
require_command $ARPING and then invoke arping through the variable.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add team_create() and team_destroy() to manage team netdevices.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic for testing whether a certain command is available is used
several times in the current code base. The tests in follow-up patches
add more requirements like that.
Therefore extract the logic into a named function, require_command(),
that can be used directly from lib.sh as well as from any test that
wishes to declare dependence on some command.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Ido's suggestion, this patch is to add a selftest for directed
broadcast forwarding with vrf. It does the assertion by checking
the src IP of the echo-reply packet in ping_test_from.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The shared block support is only needed for tc_shblock.sh. No need to
require that for other test.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for device-only IPv6 multipath next hops was dropped in
commit 33bd5ac54d ("net/ipv6: Revert attempt to simplify route replace
and append") and as of commit b5d2d75e07 ("net/ipv6: Do not allow
device only routes via the multipath API"), attempts to add a next hop
like that yield an explicit diagnostic.
Correspondingly, drop the IPv6 parts of GRE multipath test that are
supposed to test that code.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mirrored packets arrive at $h3 encapsulated in GRE/IPv4, with IP
address from 192.0.2.128/28 network. However the interface is configured
as a member of 192.0.2.160/28 and there's no route directing traffic
from the former network through that interface. Correspondingly, the RP
filter on the VRF rejects it.
Therefore turn off the VRF's RP filter.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function do_test_span_vlan_dir_ips() is used for testing whether
mirrored packets are VLAN-encapsulated. But since it only considers
VLAN encapsulation, it may end up matching unmirrored ARP traffic as
well. One consequence is a rare failure of mirror_gre_vlan_bridge_1q's
test_gretap_untagged_egress. Decreasing ping cadence in mirror_test()
makes the problem easily reproducible.
Therefore tighten up the match criterion to only count those 802.1q
packets where the next header is IP.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next patch introduces a new mlxsw-specific test that uses
mirror_gre_lib.sh and mirror_gre_topo_lib.sh.
However when sourcing their own deps, these libraries assume that the
test that's running is in the same directory. That's not the case for
driver-specific tests.
So change the libraries to source their deps through $relative_path.
That variable is set up by lib.sh, which should be imported by the test
in question in any case.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test checks if the bridge port isolation feature works as expected
by performing ping/ping6 tests between hosts that are isolated (should
not work) and between an isolated and non-isolated hosts (should work).
Same test is performed for flooding from and to isolated and
non-isolated ports.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract ping and ping6 command execution so the return value can be
checked by the caller, this is needed for port isolation tests that are
intended to fail.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test for "tc action mirred egress mirror" that mirrors to gretap when
the underlay route points at a VLAN-aware bridge (802.1q).
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test for "tc action mirred egress mirror" that mirrors to gretap when
the underlay route points at a VLAN-unaware bridge (802.1d).
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This helper library contains wrappers to devlink functionality agnostic
to the underlying device.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
[petrm@mellanox.com: Split this out from another patch.]
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
setup_wait() and tc_offload_check() both assume that all NUM_NETIFS
interfaces are relevant for a given test. However, the scale test script
acts as an umbrella for a number of sub-tests, some of which may not
require all the interfaces.
Thus it's suboptimal for tc_offload_check() to query all the interfaces.
In case of setup_wait() it's incorrect, because the sub-test in question
of course doesn't configure any interfaces beyond what it needs, and
setup_wait() then ends up waiting indefinitely for the extraneous
interfaces to come up.
For that reason, give setup_wait() and tc_offload_check() an optional
parameter with a number of interfaces to probe. Fall back to global
NUM_NETIFS if the parameter is not given.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
