For serial flash support we need to:
- Add QE Par IO Bank E device tree node, a GPIO from this bank is
used for SPI chip-select line;
- Add serial-flash node;
- Add proper module alias into of/base.c.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Select HAS_RAPIDIO symbol and add rio nodes for MPC8568E-MDS
and MPC8569E-MDS boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Note that eSDHC and DUART0 are mutually exclusive on MPC8569E-MDS
boards. Default option is DUART0, so eSDHC is disabled by default.
U-Boot will fixup device tree if eSDHC should be used instead of
DUART0.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes bogus reg = <> property in the localbus node,
and fixes interrupt property (should be "interrupts").
Also add node for NAND support.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fsl,exec-units-mask should be 0xbfe to include SNOW unit in
MPC8569E's security engine.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds PCI IDs for MPC8569 and MPC8569E processors,
plus adds appropriate quirks for these IDs, and thus makes
PCI-E actually work on MPC8569E-MDS boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Between the addition of the ecm/mcm law nodes and the fact that the
get_immrbase() has been using the range property of the SoC to determine
the base address of CCSR space we no longer need the reg property at
the soc node level. It has been ill specified and varied between device
trees to cover either the {e,m}cm-law node, some odd subset of CCSR
space or all of CCSR space.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8569 is similiar to the MPC8568. It doubles the number of
QUICC Engine RISC cores from 2 to 4. Removes eTSECs, TLU and adds
the eSDHC controller.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The latest QE chip may have more Serial Number(SNUM)s of thread to use. We
will get the number of SNUMs from device tree by reading the new property
"fsl,qe-num-snums", and set 28 as the default number of SNUMs so that it is
compatible with the old QE chips' device trees which don't have this new
property. The macro QE_NUM_OF_SNUM is defined as the maximum number in QE
snum table which is 256.
Also we update the snum_init[] array with 18 more new SNUMs which are
confirmed to be useful on new chip.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Change the RISC allocation to macros instead of enum, add function to read
the number of risc engines from the new property "fsl,qe-num-riscs" under
the qe node in dts. Add new property "fsl,qe-num-riscs" description in
qe.txt
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Keep an unique machine def for the MPC8568 MDS board to handle some
subtle differences between the future MDS board. Also set the bcsrs in
setup_arch() only for mpc8568_mds because other mds has different bcsr
settings.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed the need for asm/mpc86xx.h as it was only used in mpc86xx_smp.c
and just moved the defines it cared about into there. Also fixed up
the ioremap to only map the one 4k page we need access to and to iounmap
when we are done.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also, convert them to resource_size_t (which is unsigned long
on 64-bit, so it's not a change there).
We will be using these on fsl 32b to indicate the start and size
address of memory that the pci controller can actually reach - this
is needed to determine if an address requires bounce buffering. For
now, initialize them to a standard value; in the near future, the
value will be calculated based on how the inbound windows are
programmed.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Ben Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The rstcr register mapping code was written sometime ago before
of_iomap() existed. We can use it and clean up the code a bit
and get rid of one user of get_immrbase() in the process.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new dts places most of the devices in physical address space
above 32-bits, which allows us to have more than 4GB of RAM present.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Refactor the check to determine if the quirk is applicable to the boards
into one inline function so we only have to change one place to add more
boards that the quirks might be applicable to.
Also removed a warning related to unused temp variable.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The cell-index property isn't used on PCI nodes and is ill defined.
Remove it for now and if someone comes up with a good reason and
consistent definition for it we can add it back
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 9e35ad38 ("perf_counter: Rework the perf counter
disable/enable") added code to the powerpc hw_perf_enable (renamed
from hw_perf_restore) to test cpuhw->disabled and return immediately
if it is not set (i.e. if the PMU is already enabled).
Unfortunately the test got added before cpuhw was initialized,
resulting in an oops the first time hw_perf_enable got called.
This fixes it by moving the initialization of cpuhw to before
cpuhw->disabled is tested.
[ Impact: fix oops-causing bug on powerpc ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <18960.56772.869734.304631@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I don't think anything guarantees that the objects in data.page_aligned
are a multiple of PAGE_SIZE, thus the section may end on any boundary.
So the following section, .data.cacheline_aligned needs an explicit
alignment.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Refresh and set these options:
CONFIG_SYSFS_DEPRECATED_V2: y -> n
CONFIG_INPUT_JOYSTICK: y -> n
CONFIG_HID_SONY: n -> m
CONFIG_RTC_DRV_PS3: - -> m
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
After upgrading my distcc boxes from gcc 4.2.2 to 4.4.0, the function
graph tracer broke. This was discovered on my x86 boxes.
The issue is that gcc used the same register for an output as it did for
an input in an asm statement. I first thought this was a bug in gcc and
reported it. I was notified that gcc was correct and that the output had
to be flagged as an "early clobber".
I noticed that powerpc had the same issue and this patch fixes it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when #DEBUG
is not defined. That's not really desirable in the ftrace code
which we want to be snappy.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
3334 672 4 4010 faa arch/powerpc/kernel/ftrace.o
size after:
text data bss dec hex filename
2616 360 4 2980 ba4 arch/powerpc/kernel/ftrace.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
Revert "mm: add /proc controls for pdflush threads"
viocd: needs to depend on BLOCK
block: fix the bio_vec array index out-of-bounds test
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix PCI ROM access
powerpc/pseries: Really fix the oprofile CPU type on pseries
serial/nwpserial: Fix wrong register read address and add interrupt acknowledge.
powerpc/cell: Make ptcal more reliable
powerpc: Allow mem=x cmdline to work with 4G+
powerpc/mpic: Fix incorrect allocation of interrupt rev-map
powerpc: Fix oprofile sampling of marked events on POWER7
powerpc/iseries: Fix pci breakage due to bad dma_data initialization
powerpc: Fix mktree build error on Mac OS X host
powerpc/virtex: Fix duplicate level irq events.
powerpc/virtex: Add uImage to the default images list
powerpc/boot: add simpleImage.* to clean-files list
powerpc/8xx: Update defconfigs
powerpc/embedded6xx: Update defconfigs
powerpc/86xx: Update defconfigs
powerpc/85xx: Update defconfigs
powerpc/83xx: Update defconfigs
powerpc/fsl_soc: Remove mpc83xx_wdt_init, again
This uses values from the MMCRA, SIAR and SDAR registers on
powerpc to supply more precise information for overflow events,
including a data address when PERF_RECORD_ADDR is specified.
Since POWER6 uses different bit positions in MMCRA from earlier
processors, this converts the struct power_pmu limited_pmc5_6
field, which only had 0/1 values, into a flags field and
defines bit values for its previous use (PPMU_LIMITED_PMC5_6)
and a new flag (PPMU_ALT_SIPR) to indicate that the processor
uses the POWER6 bit positions rather than the earlier
positions. It also adds definitions in reg.h for the new and
old positions of the bit that indicates that the SIAR and SDAR
values come from the same instruction.
For the data address, the SDAR value is supplied if we are not
doing instruction sampling. In that case there is no guarantee
that the address given in the PERF_RECORD_ADDR subrecord will
correspond to the instruction whose address is given in the
PERF_RECORD_IP subrecord.
If instruction sampling is enabled (e.g. because this counter
is counting a marked instruction event), then we only supply
the SDAR value for the PERF_RECORD_ADDR subrecord if it
corresponds to the instruction whose address is in the
PERF_RECORD_IP subrecord. Otherwise we supply 0.
[ Impact: support more PMU hardware features on PowerPC ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <18955.37028.48861.555309@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Although the perf_counter API allows 63-bit raw event codes,
internally in the powerpc back-end we had been using 32-bit
event codes. This expands them to 64 bits so that we can add
bits for specifying threshold start/stop events and instruction
sampling modes later.
This also corrects the return value of can_go_on_limited_pmc;
we were returning an event code rather than just a 0/1 value in
some circumstances. That didn't particularly matter while event
codes were 32-bit, but now that event codes are 64-bit it
might, so this fixes it.
[ Impact: extend PowerPC perfcounter interfaces from u32 to u64 ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <18955.36874.472452.353104@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The current disable/enable mechanism is:
token = hw_perf_save_disable();
...
/* do bits */
...
hw_perf_restore(token);
This works well, provided that the use nests properly. Except we don't.
x86 NMI/INT throttling has non-nested use of this, breaking things. Therefore
provide a reference counter disable/enable interface, where the first disable
disables the hardware, and the last enable enables the hardware again.
[ Impact: refactor, simplify the PMU disable/enable logic ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A couple of issues crept in since about 2.6.27 related to accessing PCI
device ROMs on various powerpc machines.
First, historically, we don't allocate the ROM resource in the resource
tree. I'm not entirely certain of why, I susepct they often contained
garbage on x86 but it's hard to tell. This causes the current generic
code to always call pci_assign_resource() when trying to access the said
ROM from sysfs, which will try to re-assign some new address regardless
of what the ROM BAR was already set to at boot time. This can be a
problem on hypervisor platforms like pSeries where we aren't supposed
to move PCI devices around (and in fact probably can't).
Second, our code that generates the PCI tree from the OF device-tree
(instead of doing config space probing) which we mostly use on pseries
at the moment, didn't set the (new) flag IORESOURCE_SIZEALIGN on any
resource. That means that any attempt at re-assigning such a resource
with pci_assign_resource() would fail due to resource_alignment()
returning 0.
This fixes this by doing these two things:
- The code that calculates resource flags based on the OF device-node
is improved to set IORESOURCE_SIZEALIGN on any valid BAR, and while at
it also set IORESOURCE_READONLY for ROMs since we were lacking that too
- We now allocate ROM resources as part of the resource tree. However
to limit the chances of nasty conflicts due to busted firmwares, we
only do it on the second pass of our two-passes allocation scheme,
so that all valid and enabled BARs get precedence.
This brings pSeries back the ability to access PCI ROMs via sysfs (and
thus initialize various video cards from X etc...).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
My previous pach for fixing the oprofile CPU type got somewhat mismerged
(by my fault) when it collided with another related patch. This should
finally (fingers crossed) fix the whole thing.
We make sure we keep the -old- oprofile type and CPU type whenever
one of them was specified in the first pass through the function.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There have been a series of checkstops on QS21 related to
ptcal being set up incorrectly. On systems that only
have memory on a single node, ptcal fails when it gets
a pointer to memory on the remote node.
Moreover, agressive prefetching in memcpy and other
functions may accidentally touch the first cache line
of the page that we reserve for ptcal, which causes
an ECC checkstop.
We now allocate pages only from the specified node, moves the
ptcal area into the middle of the allocated page to avoid
potential prefetch problems and prints the address of the
ptcal area to facilitate diagnostics.
Signed-off-by: Gerhard Stenzel <gerhard.stenzel@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We're currently choking on mem=4g (and above) due to memory_limit
being specified as an unsigned long. Make memory_limit
phys_addr_t to fix this.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Before when we were setting up the irq host map for mpic we passed in
just isu_size for the size of the linear map. However, for a number of
mpic implementations we have no isu (thus pass in 0) and will end up
with a no linear map (size = 0). This causes us to always call
irq_find_mapping() from mpic_get_irq().
By moving the allocation of the host map to after we've determined the
number of sources we can actually benefit from having a linear map for
the non-isu users that covers all the interrupt sources.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Description
-----------
Change ppc64 oprofile kernel driver to use the SLOT bits (MMCRA[37:39]only on
older processors where those bits are defined.
Background
----------
The performance monitor unit of the 64-bit POWER processor family has the
ability to collect accurate instruction-level samples when profiling on marked
events (i.e., "PM_MRK_<event-name>"). In processors prior to POWER6, the MMCRA
register contained "slot information" that the oprofile kernel driver used to
adjust the value latched in the SIAR at the time of a PMU interrupt. But as of
POWER6, these slot bits in MMCRA are no longer necessary for oprofile to use,
since the SIAR itself holds the accurate sampled instruction address. With
POWER6, these MMCRA slot bits were zero'ed out by hardware so oprofile's use of
these slot bits was, in effect, a NOP. But with POWER7, these bits are no
longer zero'ed out; however, they serve some other purpose rather than slot
information. Thus, using these bits on POWER7 to adjust the SIAR value results
in samples being attributed to the wrong instructions. The attached patch
changes the oprofile kernel driver to ignore these slot bits on all newer
processors starting with POWER6.
Signed-off-by: Maynard Johnson <maynardj@us.ibm.com>
Signed-off-by: Michael Wolf <mjw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 4fc665b88a "powerpc: Merge 32 and
64-bit dma code" made changes to the PCI initialisation code that added
an assignment to archdata.dma_data but only for 32 bit code. Commit
7eef440a54 "powerpc/pci: Cosmetic cleanups
of pci-common.c" removed the conditional compilation. Unfortunately,
the iSeries code setup the archdata.dma_data before that assignment was
done - effectively overwriting the dma_data with NULL.
Fix this up by moving the iSeries setup of dma_data into a
pci_dma_dev_setup callback.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The mktree utility defines some variables as "uint", although this is not a
standard C type, and so cross-compiling on Mac OS X fails. Change this to
"unsigned int".
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The interrupt controller was not handling level interrupts correctly
such that duplicate interrupts were happening. This fixes the problem
and adds edge type interrupts which are needed in Xilinx hardware.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It is common to use U-Boot on Xilinx Virtex platforms. This patch
ensures that CONFIG_DEFAULT_UIMAGE is selected for virtex
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
