From: Linus Walleij:
Ux500 device tree enablement base for the v3.12
development cycle:
- Various cleanups like remove non-existant hardware from
the Snowball device tree, prefix all files with "ste-*"
- External regulators
- Documentation updates
- Delete some minor dangling platform data
- Pin control settings for U8540 through DT
* tag 'ux500-devicetree-for-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (22 commits)
ARM: ux500: fix devicetree builds
ARM: ux500: Remove u9540.dts as it's been replaced
ARM: ux500: Apply a ste-* prefix onto dbx5x0.dtsi
ARM: ux500: Apply a ste-* prefix onto stuib.dtsi
ARM: ux500: Apply a ste-* prefix onto hrefv60plus.dts
ARM: ux500: Apply a ste-* prefix onto hrefprev60.dts Signed-off-by: Lee Jones <lee.jones@linaro.org>
ARM: ux500: Apply a ste-* prefix onto href.dtsi
ARM: ux500: Apply a ste-* prefix onto ccu9540.dts
ARM: ux500: Apply a ste-* prefix onto ccu8540.dts
ARM: ux500: Apply a ste-* prefix onto snowball.dts
ARM: ux500: Remove Snowball DTS entry for ROHM BH1780GLI ambient light sensor
ARM: ux500: Remove Snowball DTS entry for TPS61052 chip
ARM: ux500: Remove Snowball DTS entry for National Semiconductor LP5521 LED chip
ARM: ux500: Remove Toshiba TC35892 I/O Expander's DT entry from Snowball's DTS
ARM: u8540: DT: Set pinctrl mapping to i2c0,1,2,4 & 5
ARM: u8540: Add Pinctrl Device Tree settings for uart0, uart2
ARM: ux500: Stop passing MMC's platform data for Device Tree boots
Documentation: Update binding for Nomadik and DBx5x based platforms
ARM: ux500: Supply external regulator names for Snowball's DT
ARM: ux500: Provide a supply name for the AB8500 AUX regulators to use
...
Many of Key device tree bindings uses the constant number as key code
which matches with kernel header key code and then comment as follows
for reference/better readability:
linux,code = <102>; /* KEY_HOME */
Create a DT header which defines all the key code so that DT key bindings
can use it as follows:
linux,code = <KEY_HOME>;
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Move imx-audmux macro definitions to include/dt-bindings, so they can be
used for devicetree.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds pinctrl device tree settings for uart0 and uart2
for ccu8540 board.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds new, Common Clock Framework-based clock driver for Samsung
S3C64xx SoCs. The driver is just added, without actually letting the
platforms use it yet, since this requires more intermediate steps.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Pull pin control fixes from Linus Walleij:
- Driver fixes for AM33xx, SIRF and PFC pin controllers
- Fix a compile warning from the pinctrl single-register driver
- Fix a little nasty memory leak
* tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: fix a memleak when freeing maps
pinctrl: pinctrl-single: fix compile warning when no CONFIG_PM
pinctrl: sh-pfc: fix SDHI0 VccQ regulator on sh73a0 with DT
arm/dts: sirf: fix the pingroup name mismatch between drivers and dts
pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl
pinctrl: sirf: fix the pin number and mux bit for usp0
pinctrl: am33xx dt binding: correct include path
The fec/enet driver calculates MDC rate with the formula below.
ref_freq / ((MII_SPEED + 1) x 2)
The ref_freq here is the fec internal module clock, which is missing
from clk-vf610 clock driver right now. And clk-vf610 driver mistakenly
supplies RMII clock (50 MHz) as the source to fec. This results in the
situation that fec driver gets ref_freq as 50 MHz, while physically it
runs at 66 MHz (fec module clock physically sources from ipg which runs
at 66 MHz). That's why software expects MDC runs at 2.5 MHz, while the
measurement tells it runs at 3.3 MHz. And this causes the PHY KSZ8041
keeps swithing between Full and Half mode as below.
libphy: 400d0000.etherne:00 - Link is Up - 100/Full
libphy: 400d0000.etherne:00 - Link is Up - 100/Half
libphy: 400d0000.etherne:00 - Link is Up - 100/Full
libphy: 400d0000.etherne:00 - Link is Up - 100/Half
libphy: 400d0000.etherne:00 - Link is Up - 100/Full
libphy: 400d0000.etherne:00 - Link is Up - 100/Half
Add the missing module clock for ENET0 and ENET1, and correct the clock
supplying in device tree to fix above issue.
Thanks to Alison Wang <b18965@freescale.com> for debugging the issue.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Pull pin control changes from Linus Walleij:
- A large slew of improvements of the Genric pin configuration support,
and deployment in four different platforms: Rockchip, Super-H PFC,
ABx500 and TZ1090. Support BIAS_BUS_HOLD, get device tree parsing
and debugfs support into shape.
- We also have device tree support with generic naming conventions for
the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now handled in
the device core: "sleep" and "idle", removing a lot of boilerplate
code in drivers. We do not yet know if this is the final word for
pin PM, but it already make things a lot easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where several
pins are managed by a single register, and augment it to handle sleep
modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
* tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: vt8500: wmt: remove redundant dev_err call in wmt_pinctrl_probe()
pinctrl: remove bindings for pinconf options needing more thought
pinctrl: remove slew-rate parameter from tz1090
pinctrl: set unit for debounce time pinconfig to usec
pinctrl: more clarifications for generic pull configs
pinctrl: rip out the direct pinconf API
pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver
pinctrl-tz1090: add TZ1090 pinctrl driver
pinctrl: samsung: Staticize drvdata_list
pinctrl: rockchip: Add missing irq_gc_unlock() call before return error
pinctrl: abx500: rework error path
pinctrl: abx500: suppress hardcoded value
pinctrl: abx500: factorize code
pinctrl: abx500: fix abx500_gpio_get()
pinctrl: abx500: fix abx500_pin_config_set()
pinctrl: abx500: Add device tree support
sh-pfc: Guard DT parsing with #ifdef CONFIG_OF
pinctrl: add Intel BayTrail GPIO/pinctrl support
pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldoc
pinctrl: Staticize local symbols
...
Conflicts:
drivers/net/ethernet/ti/davinci_mdio.c
drivers/pinctrl/Makefile
Pull ARM SoC driver specific changes from Arnd Bergmann:
"These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to have
these changes merged through arm-soc.
As we proceed to untangle the dependencies between platform code and
driver code, the amount of changes in this category is fortunately
shrinking, for 3.11 we have 16 branches here and 101 non-merge
changesets, the majority of which are for the stedma40 dma engine
driver used in the ux500 platform. Cleaning up that code touches
multiple subsystems, but gets rid of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox is an
intermediate step and is still omap specific at the moment. Patches
exist to generalize the subsystem and add other drivers with the same
API, but those did not make it for 3.11."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
crypto: ux500: use dmaengine_submit API
crypto: ux500: use dmaengine_prep_slave_sg API
crypto: ux500: use dmaengine_device_control API
crypto: ux500/crypt: add missing __iomem qualifiers
crypto: ux500/hash: add missing static qualifiers
crypto: ux500/hash: use readl on iomem addresses
dmaengine: ste_dma40: Declare memcpy config as static
ARM: ux500: Remove mop500_snowball_ethernet_clock_enable()
ARM: ux500: Correct the EN_3v3 regulator's on/off GPIO
ARM: ux500: Provide a AB8500 GPIO Device Tree node
gpio: rcar: fix gpio_rcar_of_table
gpio-rcar: Remove #ifdef CONFIG_OF around OF-specific sections
gpio-rcar: Reference core gpio documentation in the DT bindings
clk: exynos5250: Add enum entries for divider clock of i2s1 and i2s2
ARM: dts: Update Samsung I2S documentation
ARM: dts: add clock provider information for i2s controllers in Exynos5250
ARM: dts: add Exynos audio subsystem clock controller node
clk: samsung: register audio subsystem clocks using common clock framework
ARM: dts: use #include for all device trees for Samsung
pinctrl: s3c24xx: use correct header for chained_irq functions
...
From Kukjin Kim:
based on exynos-dt-2 and s3c24xx-dt-2
- use #include for all Samsung DT
- add clk for exynos audio subsystem (audss) and i2s
- support audss and i2s for exynos5250
* tag 'common-clk-audio' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
clk: exynos5250: Add enum entries for divider clock of i2s1 and i2s2
ARM: dts: Update Samsung I2S documentation
ARM: dts: add clock provider information for i2s controllers in Exynos5250
ARM: dts: add Exynos audio subsystem clock controller node
clk: samsung: register audio subsystem clocks using common clock framework
ARM: dts: use #include for all device trees for Samsung
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The pinctrl IP inside the AM33XX family differs slightly from
what is found on OMAP2+. Define a specific header to take account
of the differences.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Audio subsystem is introduced in s5pv210 and exynos platforms.
This has seperate clock controller which can control i2s0 and
pcm0 clocks. This patch registers the audio subsystem clocks
with the common clock framework on Exynos family.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add clock support for Vybrid VF610. It uses dtc macro support to
define all clock IDs in vf610-clock.h to keep clock IDs coherence
between kernel and DT.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add clock support for i.MX6 SoloLite. It uses the dtc marco support to
define all clock IDs in imx6sl-clock.h, which will be included by both
clock driver and device tree sources, so that the data will stay sync
all the time between kernel and DT.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This driver adds support the Cortex-A9 based SoCs from Rockchip,
so at least the RK2928, RK3066 (a and b) and RK3188.
Earlier Rockchip SoCs seem to use similar mechanics for gpio
handling so should be supportable with relative small changes.
Pull handling on the rk3188 is currently a stub, due to it being
a bit different to the earlier SoCs.
Pinmuxing as well as gpio (and interrupt-) handling tested on
a rk3066a based machine.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
From Nicolas Ferre:
Again some nice DT updates for AT91:
- DMA binding update with one patch shared with slave-dma tree
- more SPI DT activation
- enable the USB gadget HS for DT platforms
* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
ARM: at91: sam9m10g45ek add udc DT support
ARM: at91: sam9g45 add udc DT support
ARM: at91: sam9x5ek add udc DT support
ARM: at91: sam9x5 add udc DT support
ARM: at91: dt: at91sam9x5: add SPI DMA client infos
ARM: at91: dt: switch DMA DT bindings to pre-processor
ARM: at91: dt: add header to define at_hdmac configuration
From Stephen Warren:
ARM: tegra: device tree updates
This branch contains all device tree updates for Tegra boards.
The changes are:
* Converted all DT files to use the C pre-processor, to support the use
of named constants. This included use of defines for GPIO, IRQ, and
clock constants.
* Enabling new features such as:
- SPI on Dalmore.
- Audio on Dalmore and Beaver.
- gpio-leds on Beaver.
- Power-supply/batter linkage on Dalmore.
* A minor fix to the RAM size node on Beaver.
It is based on previous pull request tegra-for-3.11-deps-for-usb
followed by a merge of tegra-for-3.11-deps-for-clk.
* tag 'tegra-for-3.11-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (21 commits)
ARM: tegra: enable audio on Beaver
ARM: tegra: enable audio on Dalmore
ARM: tegra: add power-supplies link between battery and charger
ARM: tegra: add audio-related nodes to Tegra114 DT
ARM: tegra114: convert device tree files to use CLK defines
ARM: tegra30: convert device tree files to use CLK defines
ARM: tegra20: convert device tree files to use CLK defines
ARM: tegra: Add charger subnode to tps65090 node
ARM: tegra: convert device tree files to use IRQ defines
ARM: tegra: convert device tree files to use GPIO defines
ARM: tegra: create a DT header defining GPIO IDs
ARM: tegra: use #include for all device trees
ARM: tegra: Add gpio-leds to Tegra30 Beaver
ARM: tegra: fix memory size on Beaver
ARM: tegra: enable spi4 on Dalmore
ARM: tegra114: create a DT header defining CLK IDs
ARM: tegra30: create a DT header defining CLK IDs
ARM: tegra20: create a DT header defining CLK IDs
ARM: tegra: update device trees for USB binding rework
ARM: tegra: modify ULPI reset GPIO properties
...
Signed-off-by: Olof Johansson <olof@lixom.net>
DMA-cell content is a concatenation of several values. In order to keep this
stuff human readable, macros are introduced.
The values for the FIFO configuration are not the same as the ones used in the
configuration register in order to keep backward compatibility. Most devices
use the half FIFO configuration but USART ones have to use the ASAP
configuration. This parameter was not initially planed to be into the at91 dma
dt binding. The third cell will be used to store this parameter, it will
become a concatenation of the FIFO configuration and of the peripheral ID. In
order to keep backward compatibility i.e. FIFO configuration is equal to 0, we
have to perform a translation since the value to put in the register to set
half FIFO is 1.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
All Tegra GPIOs are named after the GPIO bank and GPIO number within
the bank. Define a macro to calculate the GPIO ID based on those
parameters. Make the macro available via all Tegra .dtsip files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Create a header file to define the clock IDs used by the Tegra114 clock
binding. Remove the list of definitions from the binding documentation,
and refer the reader to the header file.
This will allow the same header to be used by both device tree files,
and drivers implementing this binding, which guarantees that the two
stay in sync. This also makes device trees more readable by using names
instead of magic numbers.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
[swarren, add header to clock/ instead of clk/ to match binding location]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Create a header file to define the clock IDs used by the Tegra30 clock
binding. Remove the list of definitions from the binding documentation,
and refer the reader to the header file.
This will allow the same header to be used by both device tree files,
and drivers implementing this binding, which guarantees that the two
stay in sync. This also makes device trees more readable by using names
instead of magic numbers.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
[swarren, add header to clock/ instead of clk/ to match binding location]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Create a header file to define the clock IDs used by the Tegra20 clock
binding. Remove the list of definitions from the binding documentation,
and refer the reader to the header file.
This will allow the same header to be used by both device tree files,
and drivers implementing this binding, which guarantees that the two
stay in sync. This also makes device trees more readable by using names
instead of magic numbers.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
[swarren, add header to clock/ instead of clk/ to match binding location]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The ARM GIC binding defines a few custom cells and flags for its IRQ
specifier. Provide names for those.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Many IRQ device tree bindings use the same flags. Create a header to
define those.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Many GPIO device tree bindings use the same flags. Create a header to
define those.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
