Most part of scan command data is always present, so no need
to keep it in TLV. Simplify scan command processing moving
most part of its parameters into a fixed part of
qlink_cmd_scan message.
Use fixed dwell time values for normal scan when device is not
connected, and allow wireless card decide on dwell times by
itself if it's operating as a STA and is connected. When
connected, card can select dwell times dynamically based on
traffic conditions to get best results.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With an addition of 6GHz band support, channel number can no longer be
used to uniquely identify a specific channel. Modify channel switch
command to use chandef data.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure that all elements in QLINK protocol message are aligned to
4 bytes. For this purpose add necessary amount of padding bytes to
each message. Besides, add padding for non-aligned variable length
fields, e.g. SSID, so that the first byte of the next variable length
element is aligned. to 4 bytes. Finally, introduce TLV parsing helpers
to reduce boilerplate TLV parsing code.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Each radio on a given wifi device may have different max scan SSIDs
limitation, so take this information from a per-radio info structure.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Switch to extendable implementation of channel survey dump to make sure
that any new channel statistics can be added in the future without any
backwards compatibility issues. For this purpose use a separate variable
length bitmap to pass the list of valid statistics in firmware response.
Besides, switch to using channel frequency instead of IEEE channel
number to prepare for adding support of 6GHz band.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Information about interface combinations is now available in a fixed
portion of struct qlink_resp_get_mac_info. Use that information to
get interface combinations. TLV type QTN_TLV_ID_NUM_IFACE_COMB is
not needed anymore and can be dropped.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
QLINK_CMD_PHY_PARAMS_GET command does not need to be separate,
it can be included into GET_MAC_INFO command. Merge these two
commands adding all the missing wiphy data.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To support any number of capabilities bits in the future,
replace u32 capabilities bitmask by array. Pass
capabilities from firmware using TLV element.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use MAJOR.MINOR format for QLink firmware protocol. MAJOR part is
incremented when backward compatibility is broken. Normally this
part should not be incremented unless there is a good reason for
that. MINOR part is incremented each time when new features are
added to qlink.h, e.g. new TLVs, events, commands. These changes
should not break backward compatibility. For instance, older
firmware versions may not be able to parse new flags or send new
types of events, but this does not impact normal system operations.
As part of initialization sequence, driver requests protocol version
from firmware and refuses to start in case there is a mismatch in MAJOR
part of the version.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for 11ax features: TWT responder and spatial reuse.
Add separate structure for spatial reuse parameters and pass this
structure to firmware along with other parameters in start_ap
command. Pass TWT responder value to firmware. Bump qlink
protocol version.
Signed-off-by: Mikhail Karpenko <mkarpenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware may support DFS offload. However the final decision on whether
to use it or not should be up to the user. So even if firmware supports
DFS offload, it should be enabled only if user explicitly requests it.
For this purpose introduce kernel param dfs_offload which is disabled
by default.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Extension information elements have additional field for ID. This
commit adds TLV for such elements and a structure for interface HE
capabilities communication with firmware.
Signed-off-by: Mikhail Karpenko <mkarpenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If firmware reports that it supports hardware switch capabilities,
driver needs to track and notify device whenever broadcast domain
of a particular network device changes (ie. whenever it's upper
master device changes).
Firmware needs a unique ID to tell broadcast domains from each other
which is an opaque number otherwise. For that purpose we can use
netspace:ifidx pair to uniquely identify each broadcast domain:
- if netdev is not part of a bridge, then use it's own ifidx
as a broadcast domain ID
- if netdev is part of a bridge, then use bridge netdev ifidx
as broadcast domain ID
Firmware makes sure that packets are only forwarded between
interfaces marked with the same broadcast domain ID.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add new command for getting/setting current transmit power
and propagate requests from user space to firmware.
Signed-off-by: Mikhail Karpenko <mkarpenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Report MIC failure from firmware to cfg80211 subsystem
using dedicated callback cfg80211_michael_mic_failure.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In ETSI region DFS slave device can operate in two modes on DFS channels:
- do on-channel radar detection and use higher Tx power
- don't do radar detection and use lower Tx power as a consequence
Allow user to control that behavior through qtnfmac module parameter.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use scan duration param for both active and passive scan dwell times.
Document what different types of dwell times are used for. Explicitly
specify that if unset, automatic selection by device firmware
will be used.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use control path to send EAPOL frames to make sure they are
sent with higher priority with aggregation disabled.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pass DFS region as requested by regulatory core directly to firmware
so it can initialize radar detection block accordingly.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently driver uses the same regulatory rules to register all wiphy
instances. This is not logically correct since each wiphy may have
different capabilities (different supported bands, EIRP etc).
Allow firmware to pass regulatory rules for each MAC separately.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Before regulatory notifier is invoked by a wireless core, it will
update band information for the wiphy. Pass this information to
firmware together with new region alpha2 code.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the case of SAE AP, drivers offload authentication to user-space
software, e.g. hostapd. For FullMAC drivers the procedure is as follows.
If auth_type is SAE and user space indicates external authentication
capability, then driver requests authentication offload to user-space
software using cfg80211_external_auth_request call. From that point,
auth frame exchange is performed transparently for driver: user-space
software sends/receives mgmt frames using mgmt_tx/mgmt_frame_register
cfg80211 callbacks. As soon as authenitcation is completed, user-space
software notifies driver about its status using external_auth cfg80211
callback.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the case of OWE, STA should be able to pass DH IEs from AP assoc
responses to wpa_s for processing. For this purpose DH IEs are
received from firmware in BSS_JOIN events and passed to wireless
core and then to wpa_s as additional optional rsp_ies parameter
for cfg80211_connect_result.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure that valid BSS entry exists in wireless core record
even in the case of successful connect reported by firmware.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace textual license with SPDX-License-Identifier.
Add an SPDX-License-Identifier for the Makefile.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Host wireless stack uses u32 type for RTS/FRAG threshold values.
Switch to u32 in driver: pass u32 values to firmware and let
firmware properly adapt these values according to its
internal representation.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Advertise WIPHY_FLAG_4ADDR_STATION capability to wireless core. Send
use4addr interface change flag to firmware in change_virtual_intf
cfg80211 callback.
In order to enable adding wireless station interface to bridge
one should turn on 4addr mode using the following command:
$ iw dev wlan0 set 4addr on
$ brctl addif br0 wlan0
If this commands succeeds, then interface can be added to bridge.
Note that when wireless interface is added to bridge, wpa_supplicant
should be started with appropriate -b <brname> parameter, e.g:
$ wpa_supplicant -Dnl80211 -iwlan0 -c/path/to/wpa.conf -b br0
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support of EBUSY error code for remote procedures over QLINK protocol.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware supports scan dwell time tuning for various types of scans.
Enable support for this feature:
- advertise capability to configure channel dwell time to host
- pass scan dwell parameters to wireless card in scan request
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case firmware reports that it can not do OBSS scanning for 40MHz
2.4GHz channels itself, tell userpsace to do that instead by setting
NL80211_FEATURE_NEED_OBSS_SCAN flag.
Signed-off-by: Igor mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements basic WoWLAN support in qtnfmac driver, including
processing of WoWLAN features reported by firmware and implementation
of cfg80211 suspend/resume/wakeup callbacks. Currently the following
WoWLAN triggers are supported: disconnect, magic packet,
custom pattern packet.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable support for multiple SSIDs scans. Get max number of supported
SSIDs from firmware and report to cfg80211 core.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement set_power_mgmt() callback that forwards power saving
settings to the device firmware.
Signed-off-by: Sergei Maksimenko <smaksimenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable support for source MAC address randomization of probe request
frames. Pass addr/mask randomization parameters to firmware.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce a function that will map an error code reported in reply
to a firmware command, into one of standard errno codes.
Use additional error codes to improve error reporting
for MAC address changes.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
DFS offload support implemented:
- DFS_OFFLOAD feature is advertised depending on HW capabilities
- CAC_STARTED event forwarding from HW implemented
- start_radar_detection() callback now returning -ENOTSUPP
if DFS_OFFLOAD is enabled
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update existing code handling configuration of supported interface
combinations. Current implementation is not complete since it does
not report multiple interface combinations which are incompatible
with each other. Instead current implementation packs all the
supported combinations into single entry.
In fact currently qsr10g wireless card supports the following
two distinct interface combinations:
1. STA/repeater: 1 STA and/or 1 AP
{
{ .max = 1, .types = NL80211_IFTYPE_AP},
{ .max = 1, .types = NL80211_IFTYPE_STA},
}
2. AP/mBSS
{
{ .max = 8, .types = NL80211_IFTYPE_AP},
}
The list of supported configuration is reported by firmware during
wireless card bring-up. Communication protocol between firmware
and host has been updated accordingly in order to accommodate passing
multiple interface combination entries.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Various bits of hardware and firmware versions are useful for debug
and troubleshooting. Get more information from the wireless card.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TLV is used to pass ACL data to firmware in start_ap cfg80211 callback.
Use the same approach in set_mac_acl cfg80211 callback.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This allows a running AP to blacklist STAs by their MAC addresses
respecting the configured policy (either accept or deny unless listed).
It can be setup on .start_ap or with .set_mac_acl commands.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A set of per-STA statistics can potentially change quite often.
To ensure backwards and forward compatibility,
modify GET_STA_STATS command format:
- introduce two TLV types
- first TLV is a variable-sized bitmap of statistics values
that are filled by firmware
- second TLV is a structure with statistics itself
Only values specified in first TLV are valid.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These are needed to inform userspace about features the hardware
supports (e.g. BSS Transition Management 802.11v)
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix RSSI values passed to wireless core by qtnfmac driver:
- fix RSSI values in scan results:
driver registers wiphy with CFG80211_SIGNAL_TYPE_MBM signal type,
so mBm should be passed using DBM_TO_MBM macro
- accompany firmware changes fixing RSSI values in received mgmt frames
update qlink message format and pass correct signed values to core
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement two parts of radar handling logic:
- cfg80211 .start_radar_detect callback to allow nl80211 to initiate CAC
- radar event to allow wlan device to advertize CAC and radar events
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Center frequency is not enough to describe the channel in HT and VHT
modes. For 40MHz and 80MHz channels both primary channel and center
frequency should be specified in order to qualify channel completely.
This change adds primary channel info into qlink_chandef structure.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Specifically, following parameters are needed for wireless device
configuration but were not available to it before:
- HT/VHT capabilities and capabilities masks.
- full channel info (not just IEEE number)
- BSSID hint
- previous BSSID for reassoc request
Move Management Frame Protection setting from common encr info
structure into STA-specific .connect command parameters.
Make sure that all new qlink structure definitions are alignment-safe.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current logic artificially divides "start AP" procedure into three
stages:
- generic interface configuration (security, channel etc)
- IE's processing
- enable AP mode on interface
This separation would not allow to do a proper device configuration as
first stage needs to use information from IEs that are processed on
a second stage. Which means first and second stages have to be meged.
In that case there is no point anymore to keep third stage either, so
merge all three into a single command.
This new command carries all the same info as contained in
"struct cfg80211_ap_settings".
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Data contained within "Append IEs" command (QLINK_CMD_MGMT_SET_APPIE)
duplicates QTN_TLV_ID_IE_SET TLV. Convert the command to use that TLV
instead.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
