Pull MTD updates from Brian Norris:
- A few SPI NOR ID definitions
- Kill the NAND "max pagesize" restriction
- Fix some x16 bus-width NAND support
- Add NAND JEDEC parameter page support
- DT bindings for NAND ECC
- GPMI NAND updates (subpage reads)
- More OMAP NAND refactoring
- New STMicro SPI NOR driver (now in 40 patches!)
- A few other random bugfixes
* tag 'for-linus-20140405' of git://git.infradead.org/linux-mtd: (120 commits)
Fix index regression in nand_read_subpage
mtd: diskonchip: mem resource name is not optional
mtd: nand: fix mention to CONFIG_MTD_NAND_ECC_BCH
mtd: nand: fix GET/SET_FEATURES address on 16-bit devices
mtd: omap2: Use devm_ioremap_resource()
mtd: denali_dt: Use devm_ioremap_resource()
mtd: devices: elm: update DRIVER_NAME as "omap-elm"
mtd: devices: elm: configure parallel channels based on ecc_steps
mtd: devices: elm: clean elm_load_syndrome
mtd: devices: elm: check for hardware engine's design constraints
mtd: st_spi_fsm: Succinctly reorganise .remove()
mtd: st_spi_fsm: Allow loop to run at least once before giving up CPU
mtd: st_spi_fsm: Correct vendor name spelling issue - missing "M"
mtd: st_spi_fsm: Avoid duplicating MTD core code
mtd: st_spi_fsm: Remove useless consts from function arguments
mtd: st_spi_fsm: Convert ST SPI FSM (NOR) Flash driver to new DT partitions
mtd: st_spi_fsm: Move runtime configurable msg sequences into device's struct
mtd: st_spi_fsm: Supply the W25Qxxx chip specific configuration call-back
mtd: st_spi_fsm: Supply the S25FLxxx chip specific configuration call-back
mtd: st_spi_fsm: Supply the MX25xxx chip specific configuration call-back
...
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
Commit 7351d3a5db added an index variable
as part of fixing checkpatch warnings, presumably as a tool to make some
long lines shorter, however it only set that index in the case of there
being no gaps in eccpos for the fragment being read. Which means the
later step of filling ecccode from oob_poi will use the wrong indexing
into eccpos in that case.
This patch restores the behaviour that existed prior to that change.
Signed-off-by: Ron Lee <ron@debian.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull ubifs updates from Artem Bityutskiy:
"This pull request includes the 'ubiblock' driver which provides R/O
block access to UBI volumes. It is useful for those who want to use
squashfs on top of raw flash devices. UBI will provide bit-flip
handling and wear-levelling in this case (e.g., if there are other UBI
volumes with R/W UBIFS too).
The driver is actually pretty small and it is part of the UBI kernel
subsystem. Delivered by Ezequiel Garcia, along with a piece of
documentation on the MTD web site and the user-space tool for creating
and removing block devices"
* tag 'upstream-3.15-rc1' of git://git.infradead.org/linux-ubifs:
UBI: block: Remove __initdata from ubiblock_param_ops
UBI: make UBI_IOCVOLCRBLK take a parameter for future usage
UBI: rename block device ioctls
UBI: block: Use ENOSYS as return value when CONFIG_UBIBLOCK=n
UBI: block: Add CONFIG_BLOCK dependency
UBI: block: Use 'u64' for the 64-bit dividend
UBI: block: Mark init-only symbol as __initdata
UBI: block: do not use term "attach"
UBI: R/O block driver on top of UBI volumes
Pull char/misc driver patches from Greg KH:
"Here's the big char/misc driver updates for 3.15-rc1.
Lots of various things here, including the new mcb driver subsystem.
All of these have been in linux-next for a while"
* tag 'char-misc-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (118 commits)
extcon: Move OF helper function to extcon core and change function name
extcon: of: Remove unnecessary function call by using the name of device_node
extcon: gpio: Use SIMPLE_DEV_PM_OPS macro
extcon: palmas: Use SIMPLE_DEV_PM_OPS macro
mei: don't use deprecated DEFINE_PCI_DEVICE_TABLE macro
mei: amthif: fix checkpatch error
mei: client.h fix checkpatch errors
mei: use cl_dbg where appropriate
mei: fix Unnecessary space after function pointer name
mei: report consistently copy_from/to_user failures
mei: drop pr_fmt macros
mei: make me hw headers private to me hw.
mei: fix memory leak of pending write cb objects
mei: me: do not reset when less than expected data is received
drivers: mcb: Fix build error discovered by 0-day bot
cs5535-mfgpt: Simplify dependencies
spmi: pm: drop bus-level PM suspend/resume routines
spmi: pmic_arb: make selectable on ARCH_QCOM
Drivers: hv: vmbus: Increase the limit on the number of pfns we can handle
pch_phub: Report error writing MAC back to user
...
Mention to CONFIG_MTD_ECC_BCH in the warning message can be confusing as this
doesn't match the exact name of the configuration option.
This warning showed up once to me when I was starting to set up BCH. After
checking my .config file, it took a moment before realizing it is
CONFIG_MTD_NAND_ECC_BCH instead of CONFIG_MTD_ECC_BCH.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource(). Also,
'unsigned long mem_size' is removed from 'struct omap_nand_info',
because the 'mem_size' variable is not necessary anymore.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_ioremap_resource() in order to make the code
simpler, and remove redundant return value check of
platform_get_resource_byname() because the value is
checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
ELM hardware can process up to maximum of 8 hannels in parallel for
ECC error detection. Currently the number of channels getting configured for
processing is static determined by macro ERROR_VECTOR_MAX. However, the actual
number of channels that need to be processed is the ECC step number.
This patch just avoids configuring extra unused channels.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch refactors elm_load_syndrome() to make it scalable for newer
ECC schemes by removing scheme specific macros (like ECC_BYTES*xx),
and instead using ECC control information passed during elm_config.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
ELM hardware engine is used by BCH ecc-schemes for detecting and locating ECC
errors. This patch adds the following checks for ELM hardware engine:
- ELM internal buffers are of 1K,
so it cannot process data with ecc-step-size > 1K.
- ELM engine can execute upto maximum of 8 threads in parallel,
so in *page-mode* (when complete page is processed in single iteration),
ELM cannot support ecc-steps > 8.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
You cannot mark these parameters as __initdata.
Otherwise the data is gone upon module exit.
Fixes:
[ 172.045465] BUG: unable to handle kernel paging request at ffffffffa001db38
[ 172.046020] IP: [<ffffffff81067aa4>] destroy_params+0x24/0x50
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The old API expected a "partitions" property provided a phandle to a
separate partitions node, which itself contained yet more nodes each
representing one partition. The new API rids the requirement for the
superfluous intermediary partitions node. This patch provides the
added information required for automatic parsing by the core.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Until now the dynamically configurable message sequences for read, write
and enable 32bit addressing have been global. Brian makes a good point
why this should not be the case. If there are ever two FSM's located on
the same platform, we could be potentially introducing a race condition
on "needlessly shared data".
Suggested-by: Brian Norris <computersforpeace@gmail.com>
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch allows us to prepare some of the message sequences which will
be required to talk to the S25FLxxx family of Serial Flash devices. It
also allows us to do some required extra operations after any busy wait
failures.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When an erase is requested by userspace the MTD framework calls back
into the driver to conduct the actual command issue. Here we provide the
routines which do exactly that. We can choose to either do an entire chip
erase or by sector.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When we write data to the Serial Flash chip we'll wait a predetermined
period of time before giving up. During that period of time we poll the
status register until completion.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When a read is issued by userspace the MTD framework calls back into
the driver to conduct the actual command issue and data extraction.
Here we provide the routines which do exactly that.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Most chips require a predefined set of FSM message sequences for read,
write and erase operations. This patch provides a way to set them up,
which it will do so if a chip specific initialisation routine isn't
been provided.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In the FSM driver we handle chip differences by providing the possibility
of calling back into a chip specific initialisation routine. In this patch
we provide one for the N25Qxxx series, which endeavours to setup things
like the read, write and erase sequences, as they differ from the
default. We also configure 32bit support and the amount of dummy cycles to
use.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The N25Qxxx Serial Flash devices required different sequence
configurations depending on whether they're running in 24bit (3Byte)
or 32bit (4Byte) mode. We provide those here.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Message sequences can vary depending on how many pads (lines) are
required to address the chip (mode & dummy), how many data pads (lines)
are required to write out to the chip which will determine speed
amongst other things which are detailed by the SFDP specification. We
are able to use multiple configurations for each chip, but they need
to me matched to a device's capabilities. These configurations are
listed in preference order - most preferred first.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The FSM Serial Flash Controller is driven by issuing a standard set of
register writes we call a message sequence. This patch supplies a method
to prepare the message sequence responsible for updating a chip's VCR.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Most Serial Flash chips support 24bit addressing as a default but more
recent incarnations can support 32bit. Based on information provided
though platform specific data and capabilities we can determine whether
or not our current chip can. This patch provides a means to setup the
FSM message sequence to put the chip into 32bit mode.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Based on information we can obtain though platform specific data and/or
chip capabilities we are able to determine whether or not we can handle
a SoC reset or not. To find out why this is important please read the
comment provided in the patch.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Firstly we search for our preference read/write configuration based on a
given chip's capabilities. Then we actually set up the message sequence
accordingly.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The FSM Serial Flash Controller is driven by issuing a standard set of
register writes we call a message sequence. This patch supplies a method
to prepare the message sequence responsible for setting 32bit addressing
mode on the Flash chip.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The FSM Serial Flash Controller is driven by issuing a standard set of
register writes we call a message sequence. This patch supplies a method
to prepare the message sequence responsible for erasing a single sector.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It's important for us to determine which device was used to boot from in
order to make some correct decisions surrounding Power Management. On
each of the platforms which support the FSM this is communicated via
a set of mode pins held in the system configuration area. This patch
determine the boot device and stores the result.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The FSM Serial Flash Controller is driven by issuing a standard set of
register writes we call a message sequence. This patch supplies a method
to prepare read/write FSM message sequence(s) based on chip capability
and configuration.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Take some known parameters, namely size and number of sectors and use
them to determine weather a device can support 32bit addressing or not.
If it can, set the associated flash capability flag for latter use.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Here we provide a means to traverse though all supplied FSM message
sequence configurations and pick one based on our chip's capabilities.
The first one we match will be the preferred one, as they are
presented in order of preference.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Using previously added infrastructure we can now extract a device's JEDEC
ID, compare it to a list of known and supported devices and make assumptions
based on known characteristics of a given chip.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Supply a lookup table of all the devices we intend to support. This table
is used to store device information such as; a human readable device name,
their JEDEC ID (plus the extended version), sector size and amount, a bit
store of a device's capabilities, its maximum running frequency and
possible use of a per-device configuration call-back.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
JEDEC have helped to standardise a great deal of the commands which
can be issued to a Serial Flash devices. Many of the Serial Flash
Discoverable Parameters (SFDP) commands are generic across devices.
This patch provides a shared point where these commands can be
defined.
Suggested-by: Mark Brown <broonie@kernel.org>
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Once we start supporting devices it will be handy go detect them
dynamically. This will be done using the chip's unique JEDEC ID. This
patch allows us to extract a device's JEDEC ID using the a predefined
FSM register write sequence.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
