Remove these APIs now that we've converted all users to the
replacement struct clk_hw based versions.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
clk providers shouldn't need to use the consumer APIs (clk.h).
Add provider APIs to replace the __clk_*() APIs that take a
struct clk_hw as their first argument instead of a struct clk.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Sometimes a scatter-gather has to be split into several chunks, or sub
scatter lists. This happens for example if a scatter list will be
handled by multiple DMA channels, each one filling a part of it.
A concrete example comes with the media V4L2 API, where the scatter list
is allocated from userspace to hold an image, regardless of the
knowledge of how many DMAs will fill it :
- in a simple RGB565 case, one DMA will pump data from the camera ISP
to memory
- in the trickier YUV422 case, 3 DMAs will pump data from the camera
ISP pipes, one for pipe Y, one for pipe U and one for pipe V
For these cases, it is necessary to split the original scatter list into
multiple scatter lists, which is the purpose of this patch.
The guarantees that are required for this patch are :
- the intersection of spans of any couple of resulting scatter lists is
empty.
- the union of spans of all resulting scatter lists is a subrange of
the span of the original scatter list.
- streaming DMA API operations (mapping, unmapping) should not happen
both on both the resulting and the original scatter list. It's either
the first or the later ones.
- the caller is reponsible to call kfree() on the resulting
scatterlists.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Jens Axboe <axboe@fb.com>
Firmware typically configures the PCIe fabric with a consistent Max Payload
Size setting based on the devices present at boot. A hot-added device
typically has the power-on default MPS setting (128 bytes), which may not
match the fabric.
The previous Linux default, in the absence of any "pci=pcie_bus_*" options,
was PCIE_BUS_TUNE_OFF, in which we never touch MPS, even for hot-added
devices.
Add a new default setting, PCIE_BUS_DEFAULT, in which we make sure every
device's MPS setting matches the upstream bridge. This makes it more
likely that a hot-added device will work in a system with optimized MPS
configuration.
Note that if we hot-add a device that only supports 128-byte MPS, it still
likely won't work because we don't reconfigure the rest of the fabric.
Booting with "pci=pcie_bus_peer2peer" is a workaround for this because it
sets MPS to 128 for everything.
[bhelgaas: changelog, new default, rework for pci_configure_device() path]
Tested-by: Keith Busch <keith.busch@intel.com>
Tested-by: Jordan Hargrave <jharg93@gmail.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
There are devices that need to handle block transactions
regardless of the capabilities exported by the adapter.
For performance reasons, they need to use i2c read blocks
if available, otherwise emulate the block transaction with word
or byte transactions.
Add support for a helper function that would read a data block
using the best transfer available: I2C_FUNC_SMBUS_READ_I2C_BLOCK,
I2C_FUNC_SMBUS_READ_WORD_DATA or I2C_FUNC_SMBUS_READ_BYTE_DATA.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Based on i2c-mux-gpio driver, similarly the register-based mux
switch from one bus to another by setting a single register.
The register can be on PCIe bus, local bus, or any memory-mapped
address. The endianness of such register can be specified in device
tree if used, or in platform data.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Samuel Ortiz says:
====================
NFC 4.3 pull request
This is the NFC pull request for 4.3.
With this one we have:
- A new driver for Samsung's S3FWRN5 NFC chipset. In order to
properly support this driver, a few NCI core routines needed
to be exported. Future drivers like Intel's Fields Peak will
benefit from this.
- SPI support as a physical transport for STM st21nfcb.
- An additional netlink API for sending replies back to userspace
from vendor commands.
- 2 small fixes for TI's trf7970a
- A few st-nci fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The remote checksum offload GRO did not consider the case that frag0
might be in use. This patch fixes that by accessing headers using the
skb_gro functions and not saving offsets relative to skb->head.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull irq fixes from Thomas Gleixner:
"A series of small fixlets for a regression visible on OMAP devices
caused by the conversion of the OMAP interrupt chips to hierarchical
interrupt domains. Mostly one liners on the driver side plus a small
helper function in the core to avoid open coded mess in the drivers"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/crossbar: Restore set_wake functionality
irqchip/crossbar: Restore the mask on suspend behaviour
ARM: OMAP: wakeupgen: Restore the irq_set_type() mechanism
irqchip/crossbar: Restore the irq_set_type() mechanism
genirq: Introduce irq_chip_set_type_parent() helper
genirq: Don't return ENOSYS in irq_chip_retrigger_hierarchy
Add annotation to let us know more clearly about space utilization
information of regular dentry and inline dentry.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Commit c48a11c7ad ("netvm: propagate page->pfmemalloc to skb") added
checks for page->pfmemalloc to __skb_fill_page_desc():
if (page->pfmemalloc && !page->mapping)
skb->pfmemalloc = true;
It assumes page->mapping == NULL implies that page->pfmemalloc can be
trusted. However, __delete_from_page_cache() can set set page->mapping
to NULL and leave page->index value alone. Due to being in union, a
non-zero page->index will be interpreted as true page->pfmemalloc.
So the assumption is invalid if the networking code can see such a page.
And it seems it can. We have encountered this with a NFS over loopback
setup when such a page is attached to a new skbuf. There is no copying
going on in this case so the page confuses __skb_fill_page_desc which
interprets the index as pfmemalloc flag and the network stack drops
packets that have been allocated using the reserves unless they are to
be queued on sockets handling the swapping which is the case here and
that leads to hangs when the nfs client waits for a response from the
server which has been dropped and thus never arrive.
The struct page is already heavily packed so rather than finding another
hole to put it in, let's do a trick instead. We can reuse the index
again but define it to an impossible value (-1UL). This is the page
index so it should never see the value that large. Replace all direct
users of page->pfmemalloc by page_is_pfmemalloc which will hide this
nastiness from unspoiled eyes.
The information will get lost if somebody wants to use page->index
obviously but that was the case before and the original code expected
that the information should be persisted somewhere else if that is
really needed (e.g. what SLAB and SLUB do).
[akpm@linux-foundation.org: fix blooper in slub]
Fixes: c48a11c7ad ("netvm: propagate page->pfmemalloc to skb")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Debugged-by: Vlastimil Babka <vbabka@suse.com>
Debugged-by: Jiri Bohac <jbohac@suse.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org> [3.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are some fields of this struct undocumented or old. This patch
updates the missing comments.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kalle Valo says:
====================
Major changes:
ath10k:
* add support for qca99x0 family of devices
* improve performance of tx_lock
* add support for raw mode (802.11 frame format) and software crypto
engine enabled via a module parameter
ath9k:
* add fast-xmit support
wil6210:
* implement TSO support
* support bootloader v1 and onwards
iwlwifi:
* Deprecate -10.ucode
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* polish the Miracast operation
* fix a few power consumption issues
* scan cleanup
* fixes for D0i3 system state
* add paging for devices that support it
* add again the new RBD allocation model
* add more options to the firmware debug system
* add support for frag SKBs in Tx
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since all users are now converted to the inline implementation,
remove the out-of-line implementation entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX_ENDIAN/RX_ENDIAN bits define whether to reverse the endian
order of the data DMA from/to memory. The endian order should
keep the same with cpu endian.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Update the annotation for the kaddr pointer returned by direct_access()
so that it is a __pmem pointer. This is consistent with the PMEM driver
and with how this direct_access() pointer is used in the DAX code.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add support for two new PMEM APIs, copy_from_iter_pmem() and
clear_pmem(). copy_from_iter_pmem() is used to copy data from an
iterator into a PMEM buffer. clear_pmem() zeros a PMEM memory range.
Both of these new APIs must be explicitly ordered using a wmb_pmem()
function call and are implemented in such a way that the wmb_pmem()
will make the stores to PMEM durable. Because both APIs are unordered
they can be called as needed without introducing any unwanted memory
barriers.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Prior to this change arch_has_wmb_pmem() was only called by
arch_has_pmem_api(). Both arch_has_wmb_pmem() and arch_has_pmem_api()
checked to make sure that CONFIG_ARCH_HAS_PMEM_API was enabled.
Instead, remove the old arch_has_wmb_pmem() wrapper to be rid of one
extra layer of indirection and the redundant CONFIG_ARCH_HAS_PMEM_API
check. Rename __arch_has_wmb_pmem() to arch_has_wmb_pmem() since we no
longer have a wrapper, and just have arch_has_pmem_api() call the
architecture specific arch_has_wmb_pmem() directly.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Move the x86 PMEM API implementation out of asm/cacheflush.h and into
its own header asm/pmem.h. This will allow members of the PMEM API to
be more easily identified on this and other architectures.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add a pci_scan_root_bus_msi() interface so an arch can specify the MSI
controller up front. This removes the need for a pcibios callback to set
the MSI controller later.
This is not exported because I'd like to replace the variety of "scan root
bus" interfaces with a single, more extensible interface that can handle
the MSI controller, domain, pci_ops, resources, etc. I hope this interface
is temporary.
[bhelgaas: changelog, split into separate patch]
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
CEA defines 64 modes, indexed from 1 to 64. modedb has cea_modes arrays,
which contains 64 entries. However, the code uses the CEA indices
directly, i.e. the first mode is at cea_modes[1]. This means the array
is one too short.
This does not cause references to uninitialized memory as the code in
fbmon only allows indexes up to 63, and the cea_modes does not contain
an entry for the mode 64 so it could not be used in any case.
However, the code contains a check 'if (idx > ARRAY_SIZE(cea_modes)',
and while that check is a no-op as at that point idx cannot be >= 63, it
upsets static checkers.
Fix this by increasing the cea_array size to be 65, and change the code
to allow mode 64.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
dma_request_slave_channel_compat() is meant for drivers that support
both DT and legacy platform device based probing: if DT channel DMA
setup fails, it will fall back to platform data based DMA channel setup,
using hardcoded DMA channel IDs and a filter function.
However, if the DTS doesn't provide a "dmas" property for the device,
the fallback is also used. If the legacy filter function is not
hardcoded in the DMA slave driver, but comes from platform data, it will
be NULL. Then dma_request_slave_channel_compat() will succeed
incorrectly, and return a DMA channel, as a NULL legacy filter function
actually means "all channels are OK", not "do not match".
Later, when trying to use that DMA channel, it will fail with:
rcar-dmac e6700000.dma-controller: rcar_dmac_prep_slave_sg: bad parameter: len=1, id=-22
To fix this, ensure that both the filter function and the DMA channel ID
are not NULL before using the legacy fallback.
Note that some DMA slave drivers can handle this failure, and will fall
back to PIO.
See also commit 056f6c8702 ("dmaengine: shdma: Make dummy
shdma_chan_filter() always return false"), which fixed the same issue
for the case where shdma_chan_filter() is hardcoded in a DMA slave
driver.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Unlike the previous attempt, this takes into account the fact that
we may be calling it from the recovery thread itself. Detect this
by looking at what kind of open we're doing, and checking the state
of the NFS_DELEGATION_NEED_RECLAIM if it turns out we're doing a
reboot reclaim-type open.
Cc: Olga Kornievskaia <aglo@umich.edu>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
The SG_GAPS queue flag caused checks for bio vector alignment against
PAGE_SIZE, but the device may have different constraints. This patch
adds a queue limits so a driver with such constraints can set to allow
requests that would have been unnecessarily split. The new gaps check
takes the request_queue as a parameter to simplify the logic around
invoking this function.
This new limit makes the queue flag redundant, so removing it and
all usage. Device-mappers will inherit the correct settings through
blk_stack_limits().
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
cgroup is trying to make interface consistent across different
controllers. For weight based resource control, the knob should have
the range [1, 10000] and default to 100. This patch updates
cfq-iosched so that the weight range conforms. The internal
calculations have enough range and the widening of the weight range
shouldn't cause any problem.
* blkcg_policy->cpd_bind_fn() is added. If present, this is invoked
when blkcg is attached to a hierarchy.
* cfq_cpd_init() is updated to use the new default value on the
unified hierarchy.
* cfq_cpd_bind() callback is implemented to clear per-blkg configs and
apply the default config matching the hierarchy type.
* cfqd->root_group->[leaf_]weight initialization in cfq_init_queue()
is moved into !CONFIG_CFQ_GROUP_IOSCHED block. cfq_cpd_bind() is
now responsible for initializing the initial weights when blkcg is
enabled.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkcg interface grew to be the biggest of all controllers and
unfortunately most inconsistent too. The interface files are
inconsistent with a number of cloes duplicates. Some files have
recursive variants while others don't. There's distinction between
normal and leaf weights which isn't intuitive and there are a lot of
stat knobs which don't make much sense outside of debugging and expose
too much implementation details to userland.
In the unified hierarchy, everything is always hierarchical and
internal nodes can't have tasks rendering the two structural issues
twisting the current interface. The interface has to be updated in a
significant anyway and this is a good chance to revamp it as a whole.
This patch implements blkcg interface for the unified hierarchy.
* (from a previous patch) blkcg is identified by "io" instead of
"blkio" on the unified hierarchy. Given that the whole interface is
updated anyway, the rename shouldn't carry noticeable conversion
overhead.
* The original interface consisted of 27 files is replaced with the
following three files.
blkio.stat : per-blkcg stats
blkio.weight : per-cgroup and per-cgroup-queue weight settings
blkio.max : per-cgroup-queue bps and iops max limits
Documentation/cgroups/unified-hierarchy.txt updated accordingly.
v2: blkcg_policy->dfl_cftypes wasn't removed on
blkcg_policy_unregister() corrupting the cftypes list. Fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently, blkg_conf_prep() expects input to be of the following form
MAJ:MIN NUM
and reads the NUM part into blkg_conf_ctx->v. This is quite
restrictive and gets in the way in implementing blkcg interface for
the unified hierarchy. This patch updates blkg_conf_prep() so that it
expects
MAJ:MIN BODY_STR
where BODY_STR is an arbitrary string. blkg_conf_ctx->v is replaced
with ->body which is a char pointer pointing to the start of BODY_STR.
Parsing of the body is moved to blkg_conf_prep()'s callers.
To allow using, for example, strsep() on blkg_conf_ctx->val, it is a
non-const pointer and to accommodate that const is dropped from @input
too.
This doesn't cause any behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkio interface has become messy over time and is currently the
largest. In addition to the inconsistent naming scheme, it has
multiple stat files which report more or less the same thing, a number
of debug stat files which expose internal details which shouldn't have
been part of the public interface in the first place, recursive and
non-recursive stats and leaf and non-leaf knobs.
Both recursive vs. non-recursive and leaf vs. non-leaf distinctions
don't make any sense on the unified hierarchy as only leaf cgroups can
contain processes. cgroups is going through a major interface
revision with the unified hierarchy involving significant fundamental
usage changes and given that a significant portion of the interface
doesn't make sense anymore, it's a good time to reorganize the
interface.
As the first step, this patch renames the external visible subsystem
name from "blkio" to "io". This is more concise, matches the other
two major subsystem names, "cpu" and "memory", and better suited as
blkcg will be involved in anything writeback related too whether an
actual block device is involved or not.
As the subsystem legacy_name is set to "blkio", the only userland
visible change outside the unified hierarchy is that blkcg is reported
as "io" instead of "blkio" in the subsystem initialized message during
boot. On the unified hierarchy, blkcg now appears as "io".
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: cgroups@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently, both cfq-iosched and blk-throttle keep track of
io_service_bytes and io_serviced stats. While keeping track of them
separately may be useful during development, it doesn't make much
sense otherwise. Also, blk-throttle was counting bio's as IOs while
cfq-iosched request's, which is more confusing than informative.
This patch adds ->stat_bytes and ->stat_ios to blkg (blkcg_gq),
removes the counterparts from cfq-iosched and blk-throttle and let
them print from the common blkg counters. The common counters are
incremented during bio issue in blkcg_bio_issue_check().
The outputs are still filtered by whether the policy has
blkg_policy_data on a given blkg, so cfq's output won't show up if it
has never been used for a given blkg. The only times when the outputs
would differ significantly are when policies are attached on the fly
or elevators are switched back and forth. Those are quite exceptional
operations and I don't think they warrant keeping separate counters.
v3: Update blkio-controller.txt accordingly.
v2: Account IOs during bio issues instead of request completions so
that bio-based drivers can be handled the same way.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently, blkg_[rw]stat_recursive_sum() assume that the target
counter is located in pd (blkg_policy_data); however, some counters
are planned to be moved to blkg (blkcg_gq).
This patch updates blkg_[rw]stat_recursive_sum() to take blkg and
blkg_policy pointers instead of pd. If policy is NULL, it indexes
into blkg. If non-NULL, into the blkg's pd of the policy.
The existing usages are updated to maintain the current behaviors.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkcg_[rw]stat are used as stat counters for blkcg policies. It isn't
per-cpu by itself and blk-throttle makes it per-cpu by wrapping around
it. This patch makes blkcg_[rw]stat per-cpu and drop the ad-hoc
per-cpu wrapping in blk-throttle.
* blkg_[rw]stat->cnt is replaced with cpu_cnt which is struct
percpu_counter. This makes syncp unnecessary as remote accesses are
handled by percpu_counter itself.
* blkg_[rw]stat_init() can now fail due to percpu allocation failure
and thus are updated to return int.
* percpu_counters need explicit freeing. blkg_[rw]stat_exit() added.
* As blkg_rwstat->cpu_cnt[] can't be read directly anymore, reading
and summing results are stored in ->aux_cnt[] instead.
* Custom per-cpu stat implementation in blk-throttle is removed.
This makes all blkcg stat counters per-cpu without complicating policy
implmentations.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
cgroup stats are local to each cgroup and doesn't propagate to
ancestors by default. When recursive stats are necessary, the sum is
calculated over all the descendants. This initially was for backward
compatibility to support both group-local and recursive stats but this
mode of operation makes general sense as stat update is much hotter
thafn reporting those stats.
This however ends up losing recursive stats when a child is removed.
To work around this, cfq-iosched adds its stats to its parent
cfq_group->dead_stats which is summed up together when calculating
recursive stats.
It's planned that the core stats will be moved to blkcg_gq, so we want
to move the mechanism for keeping track of the stats of dead children
from cfq to blkcg core. This patch adds blkg_[rw]stat->aux_cnt which
are atomic64_t's keeping track of auxiliary counts which are excluded
when reading local counts but included for recursive.
blkg_[rw]stat_merge() which were used by cfq to implement dead_stats
are replaced by blkg_[rw]stat_add_aux(), and cfq now forwards stats of
a dead cgroup to the aux counts of parent->stats instead of separate
->dead_stats.
This will also help making blkg_[rw]stats per-cpu.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkg (blkcg_gq) currently is created by blkcg policies invoking
blkg_lookup_create() which ends up repeating about the same code in
different policies. Theoretically, this can avoid the overhead of
looking and/or creating blkg's if blkcg is enabled but no policy is in
use; however, the cost of blkg lookup / creation is very low
especially if only the root blkcg is in use which is highly likely if
no blkcg policy is in active use - it boils down to a single very
predictable conditional and surrounding RCU protection.
This patch consolidates blkg creation to a new function
blkcg_bio_issue_check() which is called during bio issue from
generic_make_request_checks(). blkcg_bio_issue_check() is now the
only function which tries to create missing blkg's. The subsequent
policy and request_list operations just perform blkg_lookup() and if
missing falls back to the root.
* blk_get_rl() no longer tries to create blkg. It uses blkg_lookup()
instead of blkg_lookup_create().
* blk_throtl_bio() is now called from blkcg_bio_issue_check() with rcu
read locked and blkg already looked up. Both throtl_lookup_tg() and
throtl_lookup_create_tg() are dropped.
* cfq is similarly updated. cfq_lookup_create_cfqg() is replaced with
cfq_lookup_cfqg()which uses blkg_lookup().
This consolidates blkg handling and avoids unnecessary blkg creation
retries under memory pressure. In addition, this provides a common
bio entry point into blkcg where things like common accounting can be
performed.
v2: Build fixes for !CONFIG_CFQ_GROUP_IOSCHED and
!CONFIG_BLK_DEV_THROTTLING.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently, both throttle and cfq policies implement their own root
blkg (blkcg_gq) lookup fast path. This patch moves root blkg
optimization from throtl_lookup_tg() to __blkg_lookup(). cfq-iosched
currently doesn't use blkg_lookup() but will be converted and drop the
optimization too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkg_lookup() checks whether the target queue is bypassing and, if
not, calls __blkg_lookup() which first checks the lookup hint and then
performs radix tree walk. The operations upto hint checking are
trivial and there are many users of this function. This patch inlines
blkg_lookup() and the fast path part of __blkg_lookup(). The radix
tree lookup and hint update are now in blkg_lookup_slowpath().
This will help consolidating blkg handling by easing moving root blkcg
short-circuit to inlined lookup fast path.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Each active policy has a cpd (blkcg_policy_data) on each blkcg. The
cpd's were allocated by blkcg core and each policy could request to
allocate extra space at the end by setting blkcg_policy->cpd_size
larger than the size of cpd.
This is a bit unusual but blkg (blkcg_gq) policy data used to be
handled this way too so it made sense to be consistent; however, blkg
policy data switched to alloc/free callbacks.
This patch makes similar changes to cpd handling.
blkcg_policy->cpd_alloc/free_fn() are added to replace ->cpd_size. As
cpd allocation is now done from policy side, it can simply allocate a
larger area which embeds cpd at the beginning.
As ->cpd_alloc_fn() may be able to perform all necessary
initializations, this patch makes ->cpd_init_fn() optional.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
* Rename blkcg->pd[] to blkcg->cpd[] so that cpd is consistently used
for blkcg_policy_data.
* Make blkcg_policy->cpd_init_fn() take blkcg_policy_data instead of
blkcg. This makes it consistent with blkg_policy_data methods and
to-be-added cpd alloc/free methods.
* blkcg_policy_data->blkcg and cpd_to_blkcg() added so that
cpd_init_fn() can determine the associated blkcg from
blkcg_policy_data.
v2: blkcg_policy_data->blkcg initializations were missing. Added.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
