Pull sound updates from Takashi Iwai:
"It was a busy development cycle at this time, as you can see a wide
range of changes in diffstat. There are no big changes but many
refactoring and improvements. Here we go some highlights:
ALSA core:
- Procfs codes were cleaned up to use seq_file
- Procfs can be opt out via Kconfig (only for EXPERT)
- Two types of jack API were unified finally; now both kctl and input
jack devs are handled via a single function call.
HD-audio:
- Continued code restructuring for the future ASoC driver; now HDA
controller driver is split to a core helper module.
- Preliminary codes for Skylake audio support in HDA core.
- Proper i915 gfx power well management for SKL & co
- Enabled runtime PM as default for Intel HDMI/DP codecs
- Newer Tegra chip supports
- More quirks for Dell headsets, Alienware (with CA0132), etc.
- A couple of DRM ELD helper API functions
ASoC:
- Support for loading ASoC topology maps from firmware, intended to
be used to allow self-describing DSP firmware images to be built
which can map controls added by the DSP to userspace without the
kernel needing to know about individual DSP firmwares
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring
- Big refactoring, cleanup and enhancement for the Wolfson ADSP
driver
- Cleanup series for TI TAS2552 and R-CAR drivers
- Fixes and improvements on RT56xx codecs
- Support for TI TAS571x power amplifiers
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs
- Support for x86 systems with RT5650 and Qualcomm Storm
- Support for Mediatek AFE (Audio Front End) unit
- Other various small fixes to ASoC codec drivers
Firewire:
- Enhanced to allow non-blocking streams to use timestamp
synchronization
- Improve support for DM1500 and BeBoBv3
Misc:
- Cleanup of old pci API functions over all PCI sound drivers
- Fix long-standing regression of the old powermac i2c setup"
* tag 'sound-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (533 commits)
ALSA: pcm: Fix pcm_class sysfs output
ALSA: hda-beep: Update authors dead email address
ASoC: wm_adsp: Move DSP Rate controls into the codec
ASoC: wm8995: Fix setting sysclk for WM8995_SYSCLK_MCLK2 case
ALSA: hda: provide default bus io ops extended hdac
ALSA: hda: add hda link cleanup routine
ALSA: hda: add hdac_ext stream creation and cleanup routines
ASoC: rsrc-card: remove unused ret
ALSA: HDAC: move SND_HDA_PREALLOC_SIZE to core
ASoC: mediatek: Add machine driver for rt5650 rt5676 codec
ASoC: mediatek: Add machine driver for MAX98090 codec
ASoC: mediatek: Add AFE platform driver
ASoC: rsnd: remove io from rsnd_mod
ASoC: rsnd: move rsnd_mod_is_working() to rsnd_io_is_working()
ASoC: rsnd: don't use rsnd_mod_to_io() on snd_kcontrol
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_src_xxx()
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_ssi_xxx()
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_dma_xxx()
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_get_adinr()
ASoC: rsnd: add common interrupt handler for SSI/SRC/DMA
...
Pull pin control updates from Linus Walleij:
"Here is the bulk of pin control changes for the v4.2 series: Quite a
lot of new SoC subdrivers and two new main drivers this time, apart
from that business as usual.
Details:
Core functionality:
- Enable exclusive pin ownership: it is possible to flag a pin
controller so that GPIO and other functions cannot use a single pin
simultaneously.
New drivers:
- NXP LPC18xx System Control Unit pin controller
- Imagination Pistachio SoC pin controller
New subdrivers:
- Freescale i.MX7d SoC
- Intel Sunrisepoint-H PCH
- Renesas PFC R8A7793
- Renesas PFC R8A7794
- Mediatek MT6397, MT8127
- SiRF Atlas 7
- Allwinner A33
- Qualcomm MSM8660
- Marvell Armada 395
- Rockchip RK3368
Cleanups:
- A big cleanup of the Marvell MVEBU driver rectifying it to
correspond to reality
- Drop platform device probing from the SH PFC driver, we are now a
DT only shop for SuperH
- Drop obsolte multi-platform check for SH PFC
- Various janitorial: constification, grammar etc
Improvements:
- The AT91 GPIO portions now supports the set_multiple() feature
- Split out SPI pins on the Xilinx Zynq
- Support DTs without specific function nodes in the i.MX driver"
* tag 'pinctrl-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: rockchip: add support for the rk3368
pinctrl: rockchip: generalize perpin driver-strength setting
pinctrl: sh-pfc: r8a7794: add SDHI pin groups
pinctrl: sh-pfc: r8a7794: add MMCIF pin groups
pinctrl: sh-pfc: add R8A7794 PFC support
pinctrl: make pinctrl_register() return proper error code
pinctrl: mvebu: armada-39x: add support for Armada 395 variant
pinctrl: mvebu: armada-39x: add missing SATA functions
pinctrl: mvebu: armada-39x: add missing PCIe functions
pinctrl: mvebu: armada-38x: add ptp functions
pinctrl: mvebu: armada-38x: add ua1 functions
pinctrl: mvebu: armada-38x: add nand functions
pinctrl: mvebu: armada-38x: add sata functions
pinctrl: mvebu: armada-xp: add dram functions
pinctrl: mvebu: armada-xp: add nand rb function
pinctrl: mvebu: armada-xp: add spi1 function
pinctrl: mvebu: armada-39x: normalize ref clock naming
pinctrl: mvebu: armada-xp: rename spi to spi0
pinctrl: mvebu: armada-370: align spi1 clock pin naming
pinctrl: mvebu: armada-370: align VDD cpu-pd pin naming with datasheet
...
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
Add driver for NXP LPC18xx/43xx Clock Control Unit (CCU). The CCU
provides fine grained gating of most clocks present in the SoC.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Add driver for NXP LPC18xx/43xx Clock Generation Unit (CGU). The CGU
contains several clock generators and output stages that route the
clocks either directly to peripherals or to a Clock Control Unit
(CCU).
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The Broadcom Cygnus SoC is architected under the iProc architecture. It
has the following PLLs: ARMPLL, GENPLL, LCPLL0, MIPIPLL, all dervied
from an onboard crystal. Cygnus also has various ASIU clocks that are
derived directly from the onboard crystal.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
* zte/soc:
ARM: zx: Add basic defconfig support for ZX296702
ARM: dts: zx: add an initial zx296702 dts and doc
clk: zx: add clock support to zx296702
dt-bindings: Add #defines for ZTE ZX296702 clocks
Samsung DT updates for v4.2
- for exyos3250
: use s3c6410-rtc instead of exynos3250-rtc
: add JPEG codec node and support it on exynos3250-rinato
: use s3c-rtc clock id for exynos3250-rinato and monk boards
- for exynos4
: add JPEG codec node and syscon property to MIPI DPHY
: remove obsolete MIPI DPHY reg property
: enable s3c-rtc on exynos4412-trats2
- for exynos5
: add syscon property to MIPI DPHY for exynos5420
: enable s3c-rtc on exynos5420-arndale-octa
: add missing irq pinctrl for max77686 on exynos5250-smdk5250
: clk: add bindings for 32kHz clocks from s2mps11
: fix pinctrl for s2mps11-irq on exynos5420-arndale-octa
- for exynos5422-odroidxu3
: add mmc detect gpio and LEDs
: add HS400 support, simple-audio-card and rtc_src clock
* tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add syscon property to the MIPI DPHY for exynos4415
ARM: dts: Remove obsolete MIPI DPHY 'reg' property for exynos4
ARM: dts: Use last parent for clocks during power domain on/off
ARM: dts: add support JPEG codec for exynos3250-rinato
ARM: dts: support simple-audio-card for exynos5420 and exynos5422-odroidxu3
ARM: dts: add jpeg-codec node for exynos4 and exynos4x12
ARM: dts: Enable S3C RTC on exynos4412-trats2 and exynos5420-arndale-octa
ARM: dts: Use define for s3c-rtc clock id for exynos3250-monk
ARM: dts: Use define for s3c-rtc clock id for exynos3250-rinato
ARM: dts: Use s3c6410-rtc instead of exynos3250-rtc for exynos3250/4415
ARM: dts: add 'rtc_src' clock to rtc node for exynos5422-odroidxu3
clk: samsung: Add bindings for 32kHz clocks from s2mps11
ARM: dts: fix pinctrl for s2mps11-irq on exynos5420-arndale-octa
ARM: dts: Add syscon property to the MIPI phy in exynos5420
ARM: dts: Add HS400 support for exynos5422-odroidxu3
ARM: dts: Add LEDs for exynos5422-odroidxu3
ARM: dts: add mmc detect gpio for exynos5422-odroidxu3
ARM: dts: add JPEG codec device node for exynos3250
ARM: dts: Add missing irq pinctrl for max77686 on smdk5250
The i.MX device tree changes for 4.2:
- Add device tree for i.MX7D SoC and imx7d-sdb board
- New i.MX6 board support: Armadeus Systems APF6, Gateworks GW5510,
and aristainetos2 boards
- Change LVDS to use simple-panel for nitrogen6x and sabrelite boards
- Add Wifi/Bluetooth devices support for cubox-i board
- Remove unused regulators and correct OTG roles setting for
imx6sl-warp board
- Add I2C support for imx23-olinuxino board
- Move imx6qdl HDMI device to a better place
- Add power-domain for imx6qdl CODA device
* tag 'imx-dt-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (24 commits)
ARM: dts: imx6dl: add imx6dl gpt specific compatible string
ARM: dts: imx6: add DT for aristainetos2 board
ARM: dts: cubox-i/hummingboard: Fix the license text
ARM: dts: sabrelite: use simple-panel instead of display-timings for LVDS0
ARM: dts: nitrogen6x: use simple-panel instead of display-timings for LVDS0
ARM: dts: add imx7d-sdb support
ARM: dts: add imx7d soc dtsi file
ARM: dts: Armadeus Systems APF6 family support (i.MX6)
ARM: dts: vf610: Nomenclature fixup for PTC12 pin used in RMII mode.
ARM: dts: cubox-i: add support for Broadcom Wifi/Bluetooth devices
Document: dt: binding: imx: update document for imx7d support
ARM: dts: imx6qdl: Add power-domain phandle to CODA device node
ARM: dts: Gateworks GW5510 support (i.MX6)
ARM: dts: imx6sl-warp: Fix OTG roles
ARM: dts: imx6sl-warp: Remove USB regulators
ARM: dts: imx6sl-warp: Remove unused regulator
ARM: dts: add pinfunc include file to support imx7d
ARM: mxs: fix in tree users of ssd1306
ARM: dts: imx6qdl-hummingboard: Add PCIe support
ARM: dts: imx23-olinuxino: Add i2c support
...
* clk-meson8b:
clk: meson8b: Add support for Meson8b clocks
clk: meson: Document bindings for Meson8b clock controller
clk: meson: Add support for Meson clock controller
This patchset adds the infrastructure for registering and managing the
core clocks found on Amlogic MesonX SoCs. In particular:
- PLLs
- CPU clock
- Fixed rate clocks, fixed factor clocks, ...
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Binding header file for clock input selection and configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Timer has external fast clock, and it is a mux clock.
Add the timer clock type for timer driver.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the TI dp83867 Gigabit ethernet phy
device.
The DP83867 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabled DAP (debug access port) by default. This enables the hw-
breakpoint framework to make use of the breakpoints and watchpoints
supported by hardware.
[ 0.215805] hw-breakpoint: found 2 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.224624] hw-breakpoint: maximum watchpoint size is 4 bytes.
Without this clock, the hw-breakpoint driver claims an undefined
instruction during initialization:
[ 0.227380] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0
[ 0.227519] hw-breakpoint: CPU 0 failed to disable vector catch
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It adds the imx7d clock ID definitions which will be used by both imx7d
clock driver and device tree.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Merge "Device tree related changes for omaps" from Tony Lindgren:
- Configure MMC data lines 4..8 for 1.8V IO on boards that
are using them as GPIOs instead of MMC data lines
- Add support for Baltos IR5221
- Add device tree support for LogicPD Torpedo devkit
- Add 3717 core pinctrl region
- Add gta04 1w and GSM audio support
- Add wilink and ov2659 support for am437x-gp-evm
- Add am335x-evm bluetooth and mmc3 support
- Enable omap5-uevm uart wakeup interrupt
- Enable I2C2 on BeagleBone as it's used for the capes
- Use defines for LDP GPIO keys
* tag 'omap-for-v4.2/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-evm: add mmc3 and wlan definitions to dts
ARM: dts: Enable SDIO card interrupt for 37xx-evm
ARM: dts: Fix ldp gpio keys to use defines
ARM: dts: Beaglebone i2c definitions
ARM: dts: am437x-gp-evm: add DT nodes for ov2659 sensor
ARM: dts: add DTS for Baltos IR5221
ARM: dts: omap5-uevm: Add Uart wakeup interrupt
ARM: dts: omap3-gta04: Add GSM audio support
ARM: dts: am335x-evm: add bluetooth support
ARM: dts: am437x-gp-evm: add wilink8 support
ARM: dts: omap3-gta04: Add hdqw1 support
ARM: dts: add core2 padconf region for am3517
ARM: dts: Add minimal support for LogicPD Torpedo DM3730 devkit
ARM: OMAP3: Add support for configuring MMC pins as GPIO pins
This patch adds apq8016 lpass driver support. APQ8016 has 4 MI2S which
can be routed to one internal codec and 2 external codec interfaces.
Primary, Secondary, Quaternary I2S can do Rx(playback) and Tertiary and
Quaternary can do Tx(capture).
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding the jack type to the dt-bindings directory will allow for device
tree files to specify the type of audio jacks that are present for a
board.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
enable mmc3 used for wlan and uart3 used for bluetooth
configure the gpios used for wlan and bluetooth controls
add fixed voltage regulator used for wlan power control
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch add support for select accessory detect mode to HPDETL or HPDETR.
Arizona provides a headphone detection circuit on the HPDETL and HPDETR pins
to measure the impedance of an external load connected to the headphone.
Depending on board design, headphone detect pins can change to HPDETR or HPDETL.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This creates include/dt-bindings/clock/samsung,s2mps11.h with
the three 32kHz clock outputs from the s2mps11 mfd.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Merge "RaspberryPi Device Tree changes due for v4.2" from Lee Jones:
* tag 'rpi-dt-for-armsoc-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rpi/linux-rpi:
ARM: bcm2835: dt: Use 0x4 prefix for DMA bus addresses to SDRAM.
ARM: bcm2835: dt: Add the mailbox to the device tree
ARM: bcm2835: dt: Fix i2c0 node name
ARM: bcm2835: dt: Use pinctrl header
ARM: bcm2835: dt: Add header file for pinctrl constants
ARM: bcm2835: dt: Add root properties for Raspberry Pi
ARM: bcm2835: dt: Add vendor prefix for Raspberry Pi
Merge "Renesas ARM Based SoC DT Updates for v4.2" from Simon Horman:
* Enable DMA for HSUSB on r8a7790 and r8a7791 SoCs
* Configure the HOME key as wake-up source on kzm9g board
* Use generic names for device nodes on SH Mobile SoCs and boards
* Add "nor-jedec" compatible value to SH Mobile boards
* Add IRQC clock to r8a73a4, r8a779* SoCs
* Remove MSIOF address from r8a7790 and r8a7791 SoCs
* tag 'renesas-dt-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
ARM: shmobile: r8a7791: Enable DMA for HSUSB
ARM: shmobile: r8a7791: add USB-DMAC device nodes
ARM: shmobile: r8a7790: Enable DMA for HSUSB
ARM: shmobile: r8a7790: add USB-DMAC device nodes
ARM: shmobile: kzm9g dts: Configure the HOME key as wake-up source
ARM: shmobile: koelsch dts: Use generic names for device nodes
ARM: shmobile: lager dts: Use generic names for device nodes
ARM: shmobile: bockw dts: Use generic names for device nodes
ARM: shmobile: koelsch dts: Add "nor-jedec" compatible value
ARM: shmobile: bockw dts: Add "nor-jedec" compatible value
ARM: shmobile: lager dts: Add "nor-jedec" compatible value
ARM: shmobile: bockw-reference dts: Add "nor-jedec" compatible value
ARM: shmobile: henninger dts: Add "nor-jedec" compatible value
ARM: shmobile: armadillo800eva dts: Use generic names for device nodes
ARM: shmobile: marzen dts: Use generic names for device nodes
ARM: shmobile: kzm9d dts: Use generic names for device nodes
ARM: shmobile: ape6evm dts: Use generic names for device nodes
ARM: shmobile: sh73a0 dtsi: Use generic names for device nodes
ARM: shmobile: r8a7791 dtsi: Use generic names for device nodes
ARM: shmobile: r8a7790 dtsi: Use generic names for device nodes
...
This new header file defines pincontrol constants to use
from bcm2835 DTS files for pincontrol properties option.
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link the external IRQ controller irqc0 to the IRQC module clock, so it
can be power managed using that clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the external IRQ controller irqc0 to the IRQC module clock, so it
can be power managed using that clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the external IRQ controller irqc0 to the IRQC module clock, so it
can be power managed using that clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the external IRQ controllers irqc0 and irqc1 to the IRQC module
clock, so they can be power managed using that clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[horms: corrected typo in changelog to refer to r8a73a4]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ST's Low Power Controller can currently operate in two supported modes;
Watchdog and Real Time Clock. These defines will aid engineers to easily
identify the selected mode.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull ARM SoC multiplatform code changes from Olof Johansson:
"The changes here belong to two main platforms:
- Atmel At91 is flipping the bit and going multiplatform. This
includes some cleanups and removal of code, and the final flip of
config dependencies
- Shmobile has several platforms that are going multiplatform, but
this branch also contains a bunch of cleanups that they weren't
able to keep separate in a good way. THere's also a removal of one
of their SoCs and the corresponding boards (sh7372 and mackerel)"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
ARM: at91/pm: move AT91_MEMCTRL_* to pm.h
ARM: at91/pm: move the standby functions to pm.c
ARM: at91: fix pm_suspend.S compilation when ARMv6 is selected
ARM: at91: add a Kconfig dependency on multi-platform
ARM: at91: drop AT91_TIMER_HZ
ARM: at91: remove hardware.h
ARM: at91: remove SoC headers
ARM: at91: remove useless mach/cpu.h
ARM: at91: remove unused headers
ARM: at91: switch at91_dt_defconfig to multiplatform
ARM: at91: switch to multiplatform
ARM: shmobile: r8a7778: enable multiplatform target
ARM: shmobile: bockw: add sound to DT
ARM: shmobile: r8a7778: add sound to DT
ARM: shmobile: bockw: add devices hooked up to i2c0 to DT
DT: i2c: add trivial binding for OKI ML86V7667 video decoder
ARM: shmobile: r8a7778: common clock framework CPG driver
ARM: shmobile: bockw dts: set extal clock frequency
ARM: shmobile: bockw dts: Move Ethernet node to BSC
ARM: shmobile: r8a73a4: Remove legacy code
...
Pull ARM DT updates from Olof Johansson:
"As always, this tends to be one of our bigger branches. There are
lots of updates this release, but not that many jumps out as something
that needs more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- more graphics DT pieces falling into place on Exynos, bridges,
clocks.
- plenty of DT updates for Qualcomm platforms for various IP blocks
- some churn on Tegra due to switch-over to tool-generated pinctrl
data
- misc fixes and updates for Atmel at91 platforms
- various DT updates to add IP block support on Broadcom's Cygnus
platforms
- more updates for Renesas platforms as DT support is added for
various IP blocks (IPMMU, display, audio, etc)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits)
ARM: dts: alpine: add internal pci
Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135."
ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
ARM: dts: qcom: Add idle state device nodes for 8064
ARM: dts: qcom: Add idle states device nodes for 8084
ARM: dts: qcom: Add idle states device nodes for 8974/8074
ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs
devicetree: bindings: Document qcom,idle-states
devicetree: bindings: Update qcom,saw2 node bindings
dt-bindings: Add #defines for MSM8916 clocks and resets
arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree
arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes
arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes
arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974
arm: dts: qcom: Add LCC nodes
arm: dts: qcom: Add TCSR support for MSM8960
arm: dts: qcom: Add TCSR support for MSM8660
arm: dts: qcom: Add TCSR support for IPQ8064
...
Pull ARM SoC platform updates from Olof Johansson:
"Our SoC branch usually contains expanded support for new SoCs and
other core platform code. In this case, that includes:
- support for the new Annapurna Labs "Alpine" platform
- a rework greatly simplifying adding new platform support to the
MCPM subsystem (Multi-cluster power management)
- cpuidle and PM improvements for Exynos3250
- misc updates for Renesas, OMAP, Meson, i.MX. Some of these could
have gone in other branches but ended up here for various reasons"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
ARM: alpine: add support for generic pci
ARM: Exynos: migrate DCSCB to the new MCPM backend abstraction
ARM: vexpress: migrate DCSCB to the new MCPM backend abstraction
ARM: vexpress: DCSCB: tighten CPU validity assertion
ARM: vexpress: migrate TC2 to the new MCPM backend abstraction
ARM: MCPM: move the algorithmic complexity to the core code
ARM: EXYNOS: allow cpuidle driver usage on Exynos3250 SoC
ARM: EXYNOS: add AFTR mode support for Exynos3250
ARM: EXYNOS: add code for setting/clearing boot flag
ARM: EXYNOS: fix CPU1 hotplug on Exynos3250
ARM: S3C64XX: Use fixed IRQ bases to avoid conflicts on Cragganmore
ARM: cygnus: fix const declaration bcm_cygnus_dt_compat
ARM: DRA7: hwmod: Fix the hwmod class for GPTimer4
ARM: DRA7: hwmod: Add data for GPTimers 13 through 16
ARM: EXYNOS: Remove left over 'extra_save'
ARM: EXYNOS: Constify exynos_pm_data array
ARM: EXYNOS: use static in suspend.c
ARM: EXYNOS: Use platform device name as power domain name
ARM: EXYNOS: add support for async-bridge clocks for pm_domains
ARM: omap-device: add missed callback for suspend-to-disk
...
Pull media updates from Mauro Carvalho Chehab:
- a new frontend driver for new ATSC devices: lgdt3306a
- a new sensor driver: ov2659
- a new platform driver: xilinx
- the m88ts2022 tuner driver was merged at ts2020 driver
- the media controller gained experimental support for DVB and hybrid
devices
- lots of random cleanups, fixes and improvements on media drivers
* tag 'media/v4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (404 commits)
[media] uvcvideo: add support for VIDIOC_QUERY_EXT_CTRL
[media] uvcvideo: fix cropcap v4l2-compliance failure
[media] media: omap3isp: remove unused clkdev
[media] coda: Add tracing support
[media] coda: drop dma_sync_single_for_device in coda_bitstream_queue
[media] coda: fix fill bitstream errors in nonstreaming case
[media] coda: call SEQ_END when the first queue is stopped
[media] coda: fail to start streaming if userspace set invalid formats
[media] coda: remove duplicate error messages for buffer allocations
[media] coda: move parameter buffer in together with context buffer allocation
[media] coda: allocate bitstream buffer from REQBUFS, size depends on the format
[media] coda: allocate per-context buffers from REQBUFS
[media] coda: use strlcpy instead of snprintf
[media] coda: bitstream payload is unsigned
[media] coda: fix double call to debugfs_remove
[media] coda: check kasprintf return value in coda_open
[media] coda: bitrate can only be set in kbps steps
[media] v4l2-mem2mem: no need to initialize b in v4l2_m2m_next_buf and v4l2_m2m_buf_remove
[media] s5p-mfc: set allow_zero_bytesused flag for vb2_queue_init
[media] coda: set allow_zero_bytesused flag for vb2_queue_init
...
Pull clock framework updates from Michael Turquette:
"The changes to the common clock framework for 4.0 are mostly new clock
drivers and updates to existing ones for feature enhancements and bug
fixes.
There is more churn than usual in the framework core due to the change
to introduce per-user unique struct clk pointers in 4.0. This caused
several regressions to surface, some of which were sent as fixes to
4.0. New generic clock drivers were added for GPIO- and PWM-based
clock controllers.
Additionally the common clk-divider code recieved several fixes to the
way it rounds rates"
* tag 'clk-for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (91 commits)
clk: check ->determine/round_rate() return value in clk_calc_new_rates
clk: at91: usb: propagate rate modification to the parent clk
clk: samsung: exynos4: Disable ARMCLK down feature on Exynos4210 SoC
clk: don't use __initconst for non-const arrays
clk: at91: change to using endian agnositc IO
clk: clk-gpio-gate: Fix active low
clk: Add PWM clock driver
clk: Add clock driver for mb86s7x
clk: pxa: pxa3xx: add missing os timer clock
clk: tegra: Use the proper parent for plld_dsi
clk: tegra: Use generic tegra_osc_clk_init() on Tegra114
clk: tegra: Model oscillator as clock
clk: tegra: Add peripheral registers for bank Y
clk: tegra: Register the proper number of resets
clk: tegra: Remove needless initializations
clk: tegra: Use consistent indentation
clk: tegra: Various whitespace cleanups
clk: tegra: Enable HDA to HDMI clocks on Tegra124
clk: tegra: Fix a bunch of sparse warnings
clk: tegra: Fix typo tabel -> table
...
