When IOMM-vtd is active, once main kernel crashes unfinished DMAE transactions
will be blocked, putting the HW in an error state which will cause further
transactions to timeout.
Current employed logic uses wrong macros, causing the first function to be the
only function that cleanups that error state during its probe/load.
This patch allows all the functions to successfully re-load in kdump kernel.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in a kdump kernel, it's very likely that due to sync. loss with
management firmware the first PCI function to probe and reach the previous
unload flow would decide it can reset the chip and continue onward. While doing
so, it will only close its own Rx port.
On a 4-port device where 2nd port on engine is a 1g-port, the 2nd port would
allow ingress traffic after the chip is reset [assuming it was active on the
first kernel]. This would later cause a HW attention.
This changes driver flow to close both ports' 1g capabilities during the
previous driver unload flow prior to the chip reset.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two reasons for having this header in the common place:
1) Simplifying drivers that read NVRAM entries. We will be able to
safely call bcm47xx_nvram_* functions without #ifdef-s.
2) Getting NVRAM driver out of MIPS arch code. This is needed to support
BCM5301X arch which also requires this NVRAM driver. Patch for that
will follow once we get is reviewed.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: linux-soc@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8619/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch changes the driver to use ns_to_timespec64() instead of
open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use ns_to_timespec64() and
timespec64_to_ns() instead of open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On phy_mac_interrupt() call, the new_link parameter should be 0 or 1.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define UMAC_IRQ_LINK_EVENT to simplify link event handling code.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bcmgenet_init_dma() fails, it cleans up after itself. Rx and Tx
DMAs are off, and NAPI instances haven't been netif_napi_add()'ed.
Therefore, we need to skip calling bcmgenet_fini_dma() on the error
handling path. bcmgenet_resume() already does this correctly.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_fini_dma() is the only caller of __bcmgenet_fini_dma().
Move __bcmgenet_fini_dma() code inside bcmgenet_fini_dma().
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define for UMAC_IRQ_RXDMA_DONE and UMAC_IRQ_TXDMA_DONE in order
to simplify the code that handles Rx and Tx default queue interrupts.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible that due to errors [either on PCI or on device itself]
registers reads would fail, returning all-Fs.
This adds a check as early as possible so that driver will not read junk
values and make incorrect probe decisions according to them; instead,
gracefully fail the probe.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of link changes are now being stored in shared memory [by all possible
link owners], for management use [as well as possible debug information for
dumps].
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device appears to use a 64 bit nanoseconds register, and so with
this patch the driver should be ready for the year 2038.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver's clock is implemented using a timecounter, and so with
this patch the driver is ready for the year 2038.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow drivers to handle the features check for multiple tags,
move the check to ndo_features_check().
As no drivers currently handle multiple tagged TSO, introduce
dflt_features_check() and call it if the driver does not have
ndo_features_check().
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for multiple Rx queues:
1. Add NAPI context per Rx queue
2. Modify Rx interrupt and Rx NAPI code to handle multiple Rx queues
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new bcmgenet functions to handle the NAPI calls to:
netif_napi_add()
napi_enable()
napi_disable()
netif_napi_del()
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new bcmgenet functions to handle the NAPI calls to:
netif_napi_add()
napi_enable()
napi_disable()
netif_napi_del()
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more meaningful variable names int0_enable and int1_enable when
enabling bcmgenet interrupts.
For Rx default queue interrupts, use:
UMAC_IRQ_RXDMA_BDONE | UMAC_IRQ_RXDMA_PDONE
For Tx default queue interrupts, use:
UMAC_IRQ_TXDMA_BDONE | UMAC_IRQ_TXDMA_PDONE
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the two kcalloc() calls first, before proceeding into Rx/Tx DMA init.
Makes the error case handling much simpler.
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Statistics' state-machine in bnx2x driver must be synced with various driver
flows, but its current locking scheme manages to be wasteful [using 2 locks +
additional local variable] and prone to race-conditions at the same time,
as the state-machine and 'action' are being accessed under different locks.
In addition, current 'safe exec' isn't in fact safe, since the only guarantee
it gives is that DMA transactions are over, but ramrods might still be running.
This patch cleans up said logic, leaving us with a single lock for the entire
flow and removing the possible races.
Changes from v2:
- Switched into mutex locking from semaphore locking.
- Release locks on error flows.
Changes from v1:
Failure to acquire lock fails flow instead of printing a warning and
allowing access to the critical section.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the interface is not used, power down the integrated GPHY during
suspend. Similarly to bcmgenet_open(), bcmgenet_resume() powers on the GPHY
prior to any UniMAC activity.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Power up the GPHY while we are bringing-up the network interface, and
conversely, upon bring down, power the GPHY down. In order to avoid
creating hardware hazards, make sure that the GPHY gets powered on
during bcmgenet_open() prior to the UniMAC being reset as the UniMAC may
start creating activity towards the GPHY if we reverse the steps.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the GPHY power down sequence by setting all power down bits, putting
the GPHY in reset, and finally cutting the 25Mhz reference clock.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were missing a number of extra steps and delays to power-up the GPHY, update
the sequence to reflect the proper procedure here.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for implementing the power down GPHY sequence, rename
bcmgenet_ephy_power_up to illustrate that it is not EPHY specific but
PHY agnostic, and add an "enable" argument.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CK25_DIS bit controls whether a 25Mhz clock is fed to the GPHY or
not, in preparation for powering down the integrated GPHY when relevant,
make sure we clear that bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bcmgenet_power_down() fails, we would want to propagate a return
value from bcmgenet_wol_power_down_cfg() to know about this.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always use software checksumming, since the hardware does not have any
checksum offload support.
This significantly improves local TCP tx performance.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The start-of-frame and end-of-frame bits were accidentally swapped.
In the current code it does not make any difference, since they are
always used together.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Home routers based on ARM SoCs like BCM4708 also have bcma bus with core
supported by bgmac.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ARM SoCs with bgmac Ethernet hardware we don't have any normal PHY.
There is always a switch attached but it's not even controlled over MDIO
like in case of MIPS devices.
We need a fixed PHY to be able to send/receive packets from the switch.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
E1x chips (57710, 57711(E)) have no support for encapsulation
offload. bnx2x incorrectly advertises the support as available.
Setting of those features is conditional on "!CHIP_IS_E1x(bp)", but
the bp struct is not initialized yet at this point and consequently
any chip passes the check.
The check must use the "chip_is_e1x" local variable instead to work
correctly.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Hardware Filter Block (HFB) so that incoming Rx traffic
can be matched and directed to desired Rx queues.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delay the update of the TDMA producer index unless this is the last SKB
in a batch, or the queue is already stopped. Move the check for whether
the queue should be stopped before the xmit_more check to avoid locking
the transmit queue in case there was a SKB submitted which has xmit_more
set.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to have both bcmgenet_xmit_single() and
bcmgenet_xmit_frag() perform a free_bds decrement and a prod_index
increment by one. In case one of these functions fails to map a SKB or
fragment for transmit, we will return and exit bcmgenet_xmit() with an
error.
We can therefore safely use our local copy of nr_frags to know by how
much we should decrement the number of free buffers available, and by
how much the producer count must be incremented and do this in the tail
of bcmgenet_xmit().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, bcmgenet_desc_rx() calls bcmgenet_rx_refill() at the end of
Rx packet processing loop, after the current Rx packet has already been
passed to napi_gro_receive(). However, bcmgenet_rx_refill() might fail
to allocate a new Rx skb, thus leaving a hole on the Rx queue where no
valid Rx buffer exists.
To eliminate this situation:
1. Rewrite bcmgenet_rx_refill() to retain the current Rx skb on the Rx
queue if a new replacement Rx skb can't be allocated and DMA-mapped.
In this case, the data on the current Rx skb is effectively dropped.
2. Modify bcmgenet_desc_rx() to call bcmgenet_rx_refill() at the top of
Rx packet processing loop, so that the new replacement Rx skb is
already in place before the current Rx skb is processed.
Signed-off-by: Petri Gynther <pgynther@google.com>
Tested-by: Jaedon Shin <jaedon.shin@gmail.com>--
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bits 31:16 of RDMA_PROD_INDEX contain Rx discarded packet count, which
are the Rx packets that had to be dropped by MAC hardware since there
was no room on the Rx queue. Add code to collect this information into
the netdev stats.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
Overlapping changes in macb driver, mostly fixes and cleanups
in 'net' overlapping with the integration of at91_ether into
macb in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add struct bcmgenet_rx_ring to hold all necessary information
for a single Rx queue.
2. Add bcmgenet_init_rx_queues() to initialize all Rx queues.
3. Modify bcmgenet_init_rx_ring() to initialize a single Rx queue.
4. Modify Rx interrupt path code to use per-queue data.
5. Modify bcmgenet_rx_refill() to use RxCB->bd_addr.
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On my test environment the throughput of a file transfer drops
from 4.4MBps to 116KBps due the number of repeated warning
messages. This patch removes the warning messages as DMA works
correctly with addresses using 0xC0000000 bits.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple Rx queues:
1. Move the initialization of priv->num_rx_bds, priv->rx_bds, and
priv->rx_cbs from bcmgenet_init_rx_ring() to bcmgenet_init_dma()
since they are not specific to a single Rx queue. Mimics the Tx
init model where priv->num_tx_bds, priv->tx_bds, and priv->tx_cbs
are initialized in bcmgenet_init_dma().
2. Program DMA_MBUF_DONE_THRESH = 1 so that future Rx queues Q0-Q15
will get per-packet Rx interrupt.
3. Group DMA_START_ADDR, RDMA_READ_PTR, RDMA_WRITE_PTR, and DMA_END_ADDR
initialization together. Mimics the Tx init model.
4. There is 1-to-1 mapping between RxCBs and RxBDs.
Precalculate RxCB->bd_addr so that it can be used in the future.
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
