[ Upstream commit 21f857f0321d0d0ea9b1a758bd55dc63d1cb2437 ]
A possible race condition was found in e1000_reset_task,
after discovering a similar issue in igb driver via
commit 024a8168b7 ("igb: reinit_locked() should be called
with rtnl_lock").
Added rtnl_lock() and rtnl_unlock() to avoid this.
Fixes: bc7f75fa97 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc9e5020971d57d7d0b3fef9e2ab2108fcb5588b ]
The comment describing the timestamps layout in the packet buffer is
wrong and the code is actually retrieving the timestamp in Timer 1
reference instead of Timer 0. This hasn't been a big issue so far
because hardware is configured to report both timestamps using Timer 0
(see IGC_SRRCTL register configuration in igc_ptp_enable_rx_timestamp()
helper). This patch fixes the comment and the code so we retrieve the
timestamp in Timer 0 reference as expected.
This patch also takes the opportunity to get rid of the hw.mac.type check
since it is not required.
Fixes: 81b055205e ("igc: Add support for RX timestamping")
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a4a1cdc5ab52118c1f2b216f4240830b6528d32 ]
The Supported Pause Frame always display "No" even though the Advertised
pause frame showing the correct setting based on the pause parameters via
ethtool. Set bit in link_ksettings to "Supported" for Pause Frame.
Before output:
Supported pause frame use: No
Expected output:
Supported pause frame use: Symmetric
Fixes: 8c5ad0dae9 ("igc: Add ethtool support")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Malli C <mallikarjuna.chilakala@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8876529465c368beafd51a70f79d7a738f2aadf4 ]
Fix Pause Frame Advertising when getting the advertisement via ethtool.
Remove setting the "advertising" bit in link_ksettings during default
case when Tx and Rx are in off state with Auto Negotiate off.
Below is the original output of advertisement link during Tx and Rx off:
Advertised pause frame use: Symmetric Receive-only
Expected output:
Advertised pause frame use: No
Fixes: 8c5ad0dae9 ("igc: Add ethtool support")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Malli C <mallikarjuna.chilakala@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6da262378c99b17b1a1ac2e42aa65acc1bd471c7 ]
This commit applies to the igc_reset_task the same changes that
were applied to the igb driver in commit 024a8168b7 ("igb:
reinit_locked() should be called with rtnl_lock")
and fix possible race in reset subtask.
Fixes: 0507ef8a03 ("igc: Add transmit and receive fastpath and interrupt handlers")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6650d31f21b8a0043613ae0a4a2e42e49dc20b2d ]
When iavf_process_config() fails, no error return code of
iavf_init_get_resources() is assigned.
To fix this bug, err is assigned with the return value of
iavf_process_config(), and then err is checked.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58cab46c622d6324e47bd1c533693c94498e4172 ]
Struct i40e_veb is allocated in function i40e_setup_pf_switch, and
stored to an array field veb inside struct i40e_pf. However when
i40e_setup_misc_vector fails, this memory leaks.
Fix this by calling exit and teardown functions.
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d785e1fec60179f534fbe8d006c890e5ad186e51 upstream.
Based on talks and indirect references ixgbe IPsec offlod do not
support IPsec tunnel mode offload. It can only support IPsec transport
mode offload. Now explicitly fail when creating non transport mode SA
with offload to avoid false performance expectations.
Fixes: 63a67fe229 ("ixgbe: add ipsec offload add and remove SA")
Signed-off-by: Antony Antony <antony@phenome.org>
Acked-by: Shannon Nelson <snelson@pensando.io>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0393e46ac48a6832b1011c233ebcef84f8dbe4f5 ]
It was possible to have Rx queues that were not available for use
by RSS. This would happen when increasing the number of Rx queues
while there was a user defined RSS LUT.
Always update the number of available RSS queues when changing the
number of Rx queues.
Fixes: 87324e747f ("ice: Implement ethtool ops for channels")
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d4907f65dc8fc5e897ad19956fca1acb3b33bc8 ]
DCBX_CAP bits were not being adjusted when switching
between SW and FW controlled LLDP.
Adjust bits to correctly indicate which mode the
LLDP logic is in.
Fixes: b94b013eb6 ("ice: Implement DCBNL support")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6aa7c8f998f4afddd73410aa043dad38162ce9e ]
Currently if an AVF driver doesn't account for the possibility of a
port VLAN when determining its max packet size then packets at MTU will
be dropped. It is not the VF driver's responsibility to account for a
port VLAN so fix this. To fix this, do the following:
1. Add a function that determines the max packet size a VF is allowed by
using the port's max packet size and whether the VF is in a port
VLAN. If a port VLAN is configured then a VF's max packet size will
always be the port's max packet size minus VLAN_HLEN. Otherwise it
will be the port's max packet size.
2. Use this function to verify the max packet size from the VF.
3. If there is a port VLAN configured then add 4 bytes (VLAN_HLEN) to
the VF's max packet size configuration.
Also, the VIRTCHNL_OP_GET_VF_RESOURCES message provides the capability
to communicate a VF's max packet size. Use the new function for this
purpose.
Fixes: 1071a8358a ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dcf7aa01c7b9f18727cbe0f9cb4136f1c6cdcc2 ]
In the driver currently, we are reporting max number of TCs
to the DCBNL callback as a kernel define set to 8. This is
preventing userspace applications performing DCBx to correctly
down map the TCs from requested to actual values.
Report the actual max TC value to userspace from the capability
struct.
Fixes: b94b013eb6 ("ice: Implement DCBNL support")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61c1e0eb8375def7c891bfe857bb795a57090526 ]
Fix insufficient distinction between IPv4 and IPv6 addresses
when creating a filter.
IPv4 and IPv6 are kept in the same memory area. If IPv6 is added,
then it's caught by IPv4 check, which leads to err -95.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc8812626440fa6a27f1f3f654f6dc435e042e42 ]
When creating VFs they were sometimes not getting resources.
It was caused by not executing i40e_reset_all_vfs due to
flag __I40E_VF_DISABLE being set on PF. Because of this
IAVF was never able to finish setup sequence never
getting reset indication from PF.
Changed test_and_set_bit __I40E_VF_DISABLE in
i40e_sync_filters_subtask to test_bit and removed clear_bit.
This function should not set this bit it should only check
if it hasn't been already set.
Fixes: a7542b8760 ("i40e: check __I40E_VF_DISABLE bit in i40e_sync_filters_subtask")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28b1208e7a7fa3ddc9345b022bb93e53d9dcc28a ]
Fix addition of VLAN filter for PF after enabling FW LLDP agent.
Changing LLDP Agent causes FW to re-initialize per NVM settings.
Remove default PF filter and move "Enable/Disable" to currently used
reset flag.
Without this patch PF would try to add MAC VLAN filter with default
switch filter present. This causes AQ error and sets promiscuous mode
on.
Fixes: c65e78f87f ("i40e: Further implementation of LLDP")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cdb9f80dcd46aab3c0020b4a6920c22735c5d6e ]
During driver loading flow control settings were written to FW
using a variable which was always zero, since it was being set
only by ethtool. This behavior has been corrected and driver
no longer overwrites the default FW/NVM settings.
Fixes: 373149fc99 ("i40e: Decrease the scope of rtnl lock")
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92c6058024e87087cf1b99b0389d67c0a886360e ]
When a packet contains an IPv6 header with next header which is
an extension header and not a protocol one, the kernel function
skb_transport_header called with such sk_buff will return a
pointer to the extension header and not to the TCP one.
The above explained call caused a problem with packet processing
for skb with encapsulation for tunnel with I40E_TX_CTX_EXT_IP_IPV6.
The extension header was not skipped at all.
The ipv6_skip_exthdr function does check if next header of the IPV6
header is an extension header and doesn't modify the l4_proto pointer
if it points to a protocol header value so its safe to omit the
comparison of exthdr and l4.hdr pointers. The ipv6_skip_exthdr can
return value -1. This means that the skipping process failed
and there is something wrong with the packet so it will be dropped.
Fixes: a3fd9d8876 ("i40e/i40evf: Handle IPv6 extension headers in checksum offload")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f559a356043a55bab25a4c00505ea65c50a956fb ]
This reverts commit 2ad1274fa3
VF queues were not brought up when PF was brought up after being
downed if the VF driver disabled VFs queues during PF down.
This could happen in some older or external VF driver implementations.
The problem was that PF driver used vf->queues_enabled as a condition
to decide what link-state it would send out which caused the issue.
Remove the check for vf->queues_enabled in the VF link notify.
Now VF will always be notified of the current link status.
Also remove the queues_enabled member from i40e_vf structure as it is
not used anymore. Otherwise VNF implementation was broken and caused
a link flap.
The original commit was a workaround to avoid breaking existing VFs though
it's really a fault of the VF code not the PF. The commit should be safe to
revert as all of the VFs we know of have been fixed. Also, since we now
know there is a related bug in the workaround, removing it is preferred.
Fixes: 2ad1274fa3 ("i40e: don't report link up for a VF who hasn't enabled")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b881145642ce0bbe2be521e0882e72a5cebe93b8 ]
Check return value from ret_val to make error check actually work.
Fixes: 4eb8080143 ("igc: Add setup link functionality")
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebc8d125062e7dccb7922b2190b097c20d88ad96 ]
This patch sets the default return value to -IGC_ERR_NVM in
igc_write_nvm_srwr. Without this change it wouldn't lead to a shadow RAM
write EEWR timeout.
Fixes: ab40561268 ("igc: Add NVM support")
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 329a3678ec69962aa67c91397efbd46d36635f91 ]
Link speed advertising in igc has two problems:
- When setting the advertisement via ethtool, the link speed is converted
to the legacy 32 bit representation for the intel PHY code.
This inadvertently drops ETHTOOL_LINK_MODE_2500baseT_Full_BIT (being
beyond bit 31). As a result, any call to `ethtool -s ...' drops the
2500Mbit/s link speed from the PHY settings. Only reloading the driver
alleviates that problem.
Fix this by converting the ETHTOOL_LINK_MODE_2500baseT_Full_BIT to the
Intel PHY ADVERTISE_2500_FULL bit explicitly.
- Rather than checking the actual PHY setting, the .get_link_ksettings
function always fills link_modes.advertising with all link speeds
the device is capable of.
Fix this by checking the PHY autoneg_advertised settings and report
only the actually advertised speeds up to ethtool.
Fixes: 8c5ad0dae9 ("igc: Add ethtool support")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67a3c6b3cc40bb217c3ff947a55053151a00fea0 ]
This change simplifies the VF initialization check and also minimizes
the delay between acquiring the VSI pointer and using it. As known by
the commit being fixed, there is a risk of the VSI pointer getting
changed. Therefore minimize the delay between getting and using the
pointer.
Fixes: 9889707b06 ("i40e: Fix crash caused by stress setting of VF MAC addresses")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3fe97f64384fa4073d9dc0278c4b351c92e295c ]
The current MSI-X enablement logic tries to enable best-case MSI-X
vectors and if that fails we only support a bare-minimum set. This
includes a single MSI-X for 1 Tx and 1 Rx queue and a single MSI-X
for the OICR interrupt. Unfortunately, the driver fails to load when we
don't get as many MSI-X as requested for a couple reasons.
First, the code to allocate MSI-X in the driver tries to allocate
num_online_cpus() MSI-X for LAN traffic without caring about the number
of MSI-X actually enabled/requested from the kernel for LAN traffic.
So, when calling ice_get_res() for the PF VSI, it returns failure
because the number of available vectors is less than requested. Fix
this by not allowing the PF VSI to allocation more than
pf->num_lan_msix MSI-X vectors and pf->num_lan_msix Rx/Tx queues.
Limiting the number of queues is done because we don't want more than
1 Tx/Rx queue per interrupt due to performance conerns.
Second, the driver assigns pf->num_lan_msix = 2, to account for LAN
traffic and the OICR. However, pf->num_lan_msix is only meant for LAN
MSI-X. This is causing a failure when the PF VSI tries to
allocate/reserve the minimum pf->num_lan_msix because the OICR MSI-X has
already been reserved, so there may not be enough MSI-X vectors left.
Fix this by setting pf->num_lan_msix = 1 for the failure case. Then the
ICE_MIN_MSIX accounts for the LAN MSI-X and the OICR MSI-X needed for
the failure case.
Update the related defines used in ice_ena_msix_range() to align with
the above behavior and remove the unused RDMA defines because RDMA is
currently not supported. Also, remove the now incorrect comment.
Fixes: 152b978a1f ("ice: Rework ice_ena_msix_range")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 943b881e35829403da638fcb34a959125deafef3 ]
Currently users could create more channels than LAN MSI-X available.
This is happening because there is no check against pf->num_lan_msix
when checking the max allowed channels and will cause performance issues
if multiple Tx and Rx queues are tied to a single MSI-X. Fix this by not
allowing more channels than LAN MSI-X available in pf->num_lan_msix.
Fixes: 87324e747f ("ice: Implement ethtool ops for channels")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13ed5e8a9b9ccd140a79e80283f69d724c9bb2be ]
Fix the driver to copy the MAC address configured in ndo_set_mac_address
into dev_addr, even if the MAC filter already exists in HW. In some
situations (e.g. bonding) the netdev's dev_addr could have been modified
outside of the driver, with no change to the HW filter, so the driver
cannot assume that they match.
Fixes: 757976ab16 ("ice: Fix check for removing/adding mac filters")
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b0b0b581b945ee27beb70e8199270a22dd5a2f6 ]
This patch is based on a similar change to i40e by Slawomir Laba:
"i40e: Implement flow for IPv6 next header (extension header)".
When a packet contains an IPv6 header with next header which is
an extension header and not a protocol one, the kernel function
skb_transport_header called with such sk_buff will return a
pointer to the extension header and not to the TCP one.
The above explained call caused a problem with packet processing
for skb with encapsulation for tunnel with ICE_TX_CTX_EIPT_IPV6.
The extension header was not skipped at all.
The ipv6_skip_exthdr function does check if next header of the IPV6
header is an extension header and doesn't modify the l4_proto pointer
if it points to a protocol header value so its safe to omit the
comparison of exthdr and l4.hdr pointers. The ipv6_skip_exthdr can
return value -1. This means that the skipping process failed
and there is something wrong with the packet so it will be dropped.
Fixes: a4e82a81f5 ("ice: Add support for tunnel offloads")
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29e2d9eb82647654abff150ff02fa1e07362214f ]
The packet classifier would occasionally misrecognize an IPv6 training
packet when the next protocol field was 0. The correct value for
unspecified protocol is IPPROTO_NONE.
Fixes: 165d80d6ad ("ice: Support IPv6 Flow Director filters")
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7128c834d30e6b2cf649f14d8fc274941786d0e1 ]
Currently, the function i40e_construct_skb_zc only frees the input xdp
buffer when the output skb is successfully built. On error, the
function i40e_clean_rx_irq_zc does not commit anything for the current
packet descriptor and simply exits the packet descriptor processing
loop, with the plan to restart the processing of this descriptor on
the next invocation. Therefore, on error the ring next-to-clean
pointer should not advance, the xdp i.e. *bi buffer should not be
freed and the current buffer info should not be invalidated by setting
*bi to NULL. Therefore, the *bi should only be set to NULL when the
function i40e_construct_skb_zc is successful, otherwise a NULL *bi
will be dereferenced when the work for the current descriptor is
eventually restarted.
Fixes: 3b4f0b66c2 ("i40e, xsk: Migrate to new MEM_TYPE_XSK_BUFF_POOL")
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/r/20210111181138.49757-1-cristian.dumitrescu@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3c98cbf22a96c1b12f48c1b2a4680dfe5cb280f9 ]
This flag can be used by an end user to disable S0ix flows on a
buggy system or by an OEM for development purposes.
If you need this flag to be persisted across reboots, it's suggested
to use a udev rule to call adjust it until the kernel could have your
configuration in a disallow list.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6cecf02e77ab9bf97e9252f9fcb8f0738a6de12c ]
commit e086ba2fcc ("e1000e: disable s0ix entry and exit flows for ME
systems") disabled s0ix flows for systems that have various incarnations of
the i219-LM ethernet controller. This changed caused power consumption
regressions on the following shipping Dell Comet Lake based laptops:
* Latitude 5310
* Latitude 5410
* Latitude 5410
* Latitude 5510
* Precision 3550
* Latitude 5411
* Latitude 5511
* Precision 3551
* Precision 7550
* Precision 7750
This commit was introduced because of some regressions on certain Thinkpad
laptops. This comment was potentially caused by an earlier
commit 632fbd5eb5 ("e1000e: fix S0ix flows for cable connected case").
or it was possibly caused by a system not meeting platform architectural
requirements for low power consumption. Other changes made in the driver
with extended timeouts are expected to make the driver more impervious to
platform firmware behavior.
Fixes: e086ba2fcc ("e1000e: disable s0ix entry and exit flows for ME systems")
Reviewed-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f1340265726e0edf8a8cef28e665b28ad6302ce9 ]
This code does not jump to exit on an error in iavf_lan_add_device(),
so the rtnl_unlock() from the normal path will follow.
Fixes: b66c7bc1cd ("iavf: Refactor init state machine")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3ac874fa84d1baaf0c0175f2a1499f5d88d528b2 ]
When removing VFs for PF added to bridge there was
an error I40E_AQ_RC_EINVAL. It was caused by not properly
resetting and reinitializing PF when adding/removing VFs.
Changed how reset is performed when adding/removing VFs
to properly reinitialize PFs VSI.
Fixes: fc60861e9b ("i40e: start up in VEPA mode by default")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 64050b5b8706d304ba647591b06e1eddc55e8bd9 ]
On the Rx side, the next_to_use index points to the next item in the
HW ring to be refilled/allocated, and next_to_clean points to the next
item to potentially be processed.
When the HW Rx ring is fully refilled, i.e. no packets has been
processed, the next_to_use will be next_to_clean - 1. When the ring is
fully processed next_to_clean will be equal to next_to_use. The latter
case is where a bug is triggered.
If the next_to_use bits are not cleared, and the "fully processed"
state is entered, a stale descriptor can be processed.
The skb-path correctly clear the status bit for the next_to_use
descriptor, but the AF_XDP zero-copy path did not do that.
This change adds the status bits clearing of the next_to_use
descriptor.
Fixes: 3b4f0b66c2 ("i40e, xsk: Migrate to new MEM_TYPE_XSK_BUFF_POOL")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d14768a7972b92c73259f0c9c45b969d85e3a60 ]
On the Rx side, the next_to_use index points to the next item in the
HW ring to be refilled/allocated, and next_to_clean points to the next
item to potentially be processed.
When the HW Rx ring is fully refilled, i.e. no packets has been
processed, the next_to_use will be next_to_clean - 1. When the ring is
fully processed next_to_clean will be equal to next_to_use. The latter
case is where a bug is triggered.
If the next_to_use bits are not cleared, and the "fully processed"
state is entered, a stale descriptor can be processed.
The skb-path correctly clear the status bit for the next_to_use
descriptor, but the AF_XDP zero-copy path did not do that.
This change adds the status bits clearing of the next_to_use
descriptor.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-12-09
This series contains updates to igb, ixgbe, i40e, and ice drivers.
Sven Auhagen fixes issues with igb XDP: return correct error value in XDP
xmit back, increase header padding to include space for double VLAN, add
an extack error when Rx buffer is too small for frame size, set metasize if
it is set in xdp, change xdp_do_flush_map to xdp_do_flush, and update
trans_start to avoid possible Tx timeout.
Björn fixes an issue where an Rx buffer can be reused prematurely with
XDP redirect for ixgbe, i40e, and ice drivers.
The following are changes since commit 323a391a22:
can: isotp: isotp_setsockopt(): block setsockopt on bound sockets
and are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue 1GbE
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The page recycle code, incorrectly, relied on that a page fragment
could not be freed inside xdp_do_redirect(). This assumption leads to
that page fragments that are used by the stack/XDP redirect can be
reused and overwritten.
To avoid this, store the page count prior invoking xdp_do_redirect().
Fixes: efc2214b60 ("ice: Add support for XDP")
Reported-and-analyzed-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The page recycle code, incorrectly, relied on that a page fragment
could not be freed inside xdp_do_redirect(). This assumption leads to
that page fragments that are used by the stack/XDP redirect can be
reused and overwritten.
To avoid this, store the page count prior invoking xdp_do_redirect().
Fixes: 6453073987 ("ixgbe: add initial support for xdp redirect")
Reported-and-analyzed-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The page recycle code, incorrectly, relied on that a page fragment
could not be freed inside xdp_do_redirect(). This assumption leads to
that page fragments that are used by the stack/XDP redirect can be
reused and overwritten.
To avoid this, store the page count prior invoking xdp_do_redirect().
Longer explanation:
Intel NICs have a recycle mechanism. The main idea is that a page is
split into two parts. One part is owned by the driver, one part might
be owned by someone else, such as the stack.
t0: Page is allocated, and put on the Rx ring
+---------------
used by NIC ->| upper buffer
(rx_buffer) +---------------
| lower buffer
+---------------
page count == USHRT_MAX
rx_buffer->pagecnt_bias == USHRT_MAX
t1: Buffer is received, and passed to the stack (e.g.)
+---------------
| upper buff (skb)
+---------------
used by NIC ->| lower buffer
(rx_buffer) +---------------
page count == USHRT_MAX
rx_buffer->pagecnt_bias == USHRT_MAX - 1
t2: Buffer is received, and redirected
+---------------
| upper buff (skb)
+---------------
used by NIC ->| lower buffer
(rx_buffer) +---------------
Now, prior calling xdp_do_redirect():
page count == USHRT_MAX
rx_buffer->pagecnt_bias == USHRT_MAX - 2
This means that buffer *cannot* be flipped/reused, because the skb is
still using it.
The problem arises when xdp_do_redirect() actually frees the
segment. Then we get:
page count == USHRT_MAX - 1
rx_buffer->pagecnt_bias == USHRT_MAX - 2
From a recycle perspective, the buffer can be flipped and reused,
which means that the skb data area is passed to the Rx HW ring!
To work around this, the page count is stored prior calling
xdp_do_redirect().
Note that this is not optimal, since the NIC could actually reuse the
"lower buffer" again. However, then we need to track whether
XDP_REDIRECT consumed the buffer or not.
Fixes: d9314c474d ("i40e: add support for XDP_REDIRECT")
Reported-and-analyzed-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Since we share the transmit queue with the network stack,
it is possible that we run into a transmit queue timeout.
This will reset the queue.
This happens under high load when XDP is using the
transmit queue pretty much exclusively.
netdev_start_xmit() sets the trans_start variable of the
transmit queue to jiffies which is later utilized by dev_watchdog(),
so to avoid timeout, let stack know that XDP xmit happened by
bumping the trans_start within XDP Tx routines to jiffies.
Fixes: 9cbc948b5a ("igb: add XDP support")
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
