From Shawn Guo <shawn.guo@linaro.org>:
It's based on imx/multiplatform branch. Most of them are dts changes.
There are also a few imx6 improvement patches in there.
* tag 'imx-dt-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: select ARM and PL310 errata
ARM: imx6q: print silicon version on boot
ARM i.MX dts: Consistently add labels to devicenodes
ARM: dts: imx6q-sabresd: add volume up/down gpio keys
ARM: dts: imx53: pinctl update
ARM: imx: enable cpufreq for imx6q
ARM: dts: imx6q: enable snvs lp rtc
ARM: dts: imx6q-sabreauto: Add basic support
ARM: imx6q: let users input debug uart port number
ARM: dts: imx53-qsb: Make DA9053 regulator functional
ARM: dts: imx53-qsb: Use pinctrl for gpio-led
ARM i.MX dtsi: Add default bus-width property for esdhc controller
Signed-off-by: Arnd Bregmann <arnd@arndb.de>
imx6q gets 5 uart ports in total. Different board design may choose
different port as debug uart. For example, imx6q-sabresd uses UART1,
imx6q-sabrelite uses UART2 and imx6q-arm2 uses UART4. Rather than
bloating DEBUG_LL choice list with all these uart ports, the patch
introduces DEBUG_IMX6Q_UART_PORT for users to input uart port number
when DEBUG_IMX6Q_UART is selected inside DEBUG_LL choice.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
From Tony Lindgren <tony@atomide.com>:
Non critical omap fixes that were not considered urgent
for the -rc cycle.
* tag 'omap-for-v3.8/fixes-non-critical-v4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (645 commits)
ARM: OMAP4: PM: fix errata handling when CONFIG_PM=n
ARM: OMAP4: retrigger localtimers after re-enabling gic
ARM: OMAP4460: Workaround for ROM bug because of CA9 r2pX GIC control register change.
ARM: OMAP4: PM: add errata support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After "ARM: vexpress: Make the debug UART detection more specific",
building allyesconfig in linux-next now gives me:
arch/arm/kernel/debug.S: Assembler messages:
arch/arm/kernel/debug.S:81: Error: selected processor does not support ARM mode `movw r2,#0xc 091'
arch/arm/kernel/debug.S:81: Error: selected processor does not support ARM mode `movt r2,#0x4 10f'
arch/arm/kernel/debug.S:97: Error: selected processor does not support ARM mode `movw r2,#0xc 091'
arch/arm/kernel/debug.S:97: Error: selected processor does not support ARM mode `movt r2,#0x4 10f'
arch/arm/kernel/debug.S:104: Error: selected processor does not support ARM mode `movw r3,#0x c091'
arch/arm/kernel/debug.S:104: Error: selected processor does not support ARM mode `movt r3,#0x 410f'
Since the code can never get executed on ARMv6 but might
be built in a configuration that has ARMv6 enabled, it's
safe to just mark it in the assembly source for being
ARMv7-only.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pawel Moll <pawel.moll@arm.com>
From Michal Simek:
* 'arm-next' of git://git.xilinx.com/linux-xlnx:
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
+ Linux 3.7-rc3
This fixes early_printk() compilation for
socfpga. (senduart/busyuart/waituart were missing). It does that by
making Picochip code generic.
Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Base the UART detection heuristic on architecturally defined
MIDR register instead of implementation dependent CBAR. The
only tile using the original memory map is V2P-CA9 with Cortex
A9 r0p1, which MIDR contains value 0x410fc091.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Move imx debug-macro.S over to common debug macro directory. It
removes the inclusion to hardware.h by hard-coding the physical
address of uart port and copying IMX_IO_P2V from hardware.h.
Since we will need a common solution, which might use a fixed virtual
address for uart port across platforms, we make a copy of IMX_IO_P2V
here as a temporary solution to enable low-level debug for imx
multi-platform build.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Move highbank debug-macro.S over to common debug macro directory.
Also, remove v7 specific movw/movt instructions so this can compile under
v6 mode.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Based on suggestion by Russell King, create a common location for debug
macros and select the included debug macro file using config option.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
