It has been pointed out by device tree maintainer for several times
that the generic names 'serial' and 'ethernet' should be used for
those devices per ePAPR. Renames imx uart and fec device tree nodes
to stop them being bad examples.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Minor DT updates based on the dt-missed-3.4 branch
By Benoit Cousson (3) and Peter Ujfalusi (2)
via Tony Lindgren
* tag 'omap-dt-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: omap4-panda: Add LEDs support
arm/dts: omap4-sdp: Add LEDs support
arm/dts: twl4030: Add twl4030-gpio node
OMAP4: devices: Do not create mcpdm device if the dtb has been provided
OMAP4: devices: Do not create dmic device if the dtb has been provided
DaVinci SoC updates for v3.5
This pull request updates the DaVinci SoC support to implement DEBUG_LL port
choice and optimizes the DMA ISR by removing unnecessary register reads.
* tag 'v3.5-soc' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: optimize the DMA ISR
ARM: davinci: implement DEBUG_LL port choice
+ sync with Linux 3.4-rc6
Signed-off-by: Olof Johansson <olof@lixom.net>
By Stephen Warren (5) and Peter De Schrijver (1)
via Stephen Warren
* 'for-3.5/tegra30-audio' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
ARM: tegra: set up audio clocks for tegra30 dt
ARM: tegra: Initialize pll_p_out1
ARM: tegra: provide clock aliases for AHUB configlink
Signed-off-by: Olof Johansson <olof@lixom.net>
"Jean-Christophe PLAGNIOL-VILLARD" <plagnioj@jcrosoft.com> writes:
ARM: AT91 more DT material
New SoC conversion and boards support
SoC convertion to DT:
- at91sam9260
- at91sam9263
boards:
- Atmel at91sam9g20ek/9263ek
- Calao TNY-A9260/A9263/A9G20
- Calao USB-A9260/A9263
- Ethernnut 5
- Kizbox
* tag 'at91-for-next-dt' of git://github.com/at91linux/linux-at91: (32 commits)
Ethernut 5 board support
ARM: at91: add kizbox board dt support.
ARM: at91: DT: add Calao TNY A9263 board support
ARM: at91: DT: add Calao USB A9263 board support
ARM: at91: add at91sam9263ek DT support
ARM: at91: add at91sam9263 DT support
ARM: at91: standard device init only if DT is not populated.
ARM: at91: DT: add Calao USB A9260 DT support
ARM: at91: Calao USB A926x factorize common binding in usb_a9260_common
ARM: at91: USB A926x update nand partition
ARM: at91: add at91sam9g20ek boards dt support
arm: at91: add Calao TNY-A9260 and TNY-A9G20 board support
ARM: at91: add at91sam9260 DT support
ARM: at91: add defconfig for device tree
ARM: at91/dt: do not specify the board any more
ARN: at91: introduce SOC_AT91xxx define to allow to compile SoC core support
ARM: at91: add SOC_AT91SAM9 kconfig option to factorise select
ARM: at91: pm select memory controler at runtime
ARM: at91: move at91_init_leds to board init
ARM: at91: do not pin mux the UARTs in init_early
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Walleij <linus.walleij@linaro.org> writes:
this pull request contains some device tree work by Lee Jones.
I have tried to keep these patches in the arch/arm/boot/dts/*
space to get some sanity in the branch proliferation.
There is still one patch that touches arch/arm/mach-ux500 too
though (but it should merge fine with the other ux500 stuff).
The changes to the device tree are of course dependent on some
core changes and some patching in the GPIO/pin driver, but as
the device tree files are believed to be a different world
(and should one day live in their own git) I split this off
anyway. I don't think people bisect the device trees per se
and the board code in conjunction anyway.
* 'ux500-devicetree-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Configure the PRCMU Timer for db8500 based devices in DT
ARM: ux500: Enable the SMSC9115 on Snowball via Device Tree
drivers/gpio: represent gpio-nomadik as an IRQ controller in DT documentation
ARM: ux500: Rename gpio_keys in the Device Tree file
drivers/gpio: gpio-nomadik: Provide documentation for Device Tree bindings
drivers/gpio: gpio-nomadik: Device Tree bindings
ARM: ux500: Enable the external bus with Device Tree
ARM: ux500: Shorten Snowball's DT compatible gpio entry
ARM: ux500: Rename the DT compatible entry for i2c devices on Snowball
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
* spear/dt:
ARM: SPEAr3xx: Correct keyboard data passed from DT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
Roland Stigge <stigge@antcom.de> writes:
this is a rearrangement of all mach-lpc32xx specific patches for device
tree conversion. Please note that:
* It builds upon the i2c-pnx changes (see previous pull request, branch
lpc32xx/i2c)
* Dave Miller gave permission to merge the lpc_eth.c change via arm-soc
(patch 1/8)
The rest of the patches is mach-lpc32xx only.
* 'lpc32xx/dt' of git://git.antcom.de/linux-2.6:
ARM: LPC32xx: Defconfig update
ARM: LPC32xx: Move common code to common.c
ARM: LPC32xx: Device tree support
ARM: LPC32xx: DTS files for device tree conversion
ARM: LPC32xx: Remove obsolete platform Kconfig
ARM: LPC32xx: clock.c registration adjustment
ARM: LPC32xx: clock.c cleanup
net: Add device tree support to LPC32xx
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a rebased version of parts of
git://git.stlinux.com/spear/linux-2.6.git spear-v3.5
which was accidentally based on the linux-next tree and mixed too
many different things. The pinctrl related changes from the same
branch are now in the spear/pinctrl branch of arm-soc.
There are a few non-DT cleanups mixed in here, but fundamentally
it's all related to the DT conversion.
* spear/dt: (9 commits)
ARM: spear: remove most mach/*.h header contents
SPEAr: Update defconfigs
SPEAr: Add PL080 DMA support for 3xx and 6xx
ARM: SPEAr3xx: Add device-tree support to SPEAr3xx architecture
SPEAr3xx: Replace printk() with pr_*()
SPEAr6xx: Add compilation support for dtbs using 'make dtbs'
SPEAr3xx: Add clock instance of usb hosts - ehci and ohci 0 and 1
SPEAr: Use CLKDEV_INIT for defining clk_lookups
ARM: SPEAr600: Change FSMC and SMI clock names
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
First part of DT changes for the Renesas shmobile platform,
pulled from:
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas.git dt
* renesas/dt:
ARM: mach-shmobile: sh7372 generic board support via DT V2
ARM: mach-shmobile: Rework sh7372 INTCS demuxer V2
ARM: mach-shmobile: Use INTC_IRQ_PINS_16H on sh7372
ARM: mach-shmobile: Use 0x3400 as INTCS vector offset
ARM: mach-shmobile: Introduce INTC_IRQ_PINS_16H
ARM: mach-shmobile: Introduce shmobile_setup_delay()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add node for the audio codec
* Enable Tegra's I2S1 controller and DAS
* Add node for top-level sound complex
Signed-off-by: Stephen Warren <swarren@nvidia.com>
According to the device's datasheet, it can support an interrupt too.
However, the existing board file doesn't specify an interrupt, and I
don't have the schematics, so I can't add an interrupts property. The
current Linux driver doesn't support anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add the known i2c devices on seaboard to the i2c table.
Also rename the temperature sensor device node, and mark it as a nct1008
instead of an adt7461 (which it is -- the chips are compatible though).
Signed-off-by: Olof Johansson <olof@lixom.net>
[swarren: Removed isl29018 from patch; it's already there now. Fixed
interrupts properties now that Tegra GPIO is an interrupt controller.
Moved smart-battery to the correct I2C bus.]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The I2C2 controller can be routed to either pingroup DDC or PTA. Seaboard
actually uses this as an I2C bus mux, and devices are connected to both
pingroups. This change statically assigns the I2C2 controller to pingroup
PTA, so that on-board devices can be accessed. The DDC pingroup is used
for EDID/DDC accesses which are not yet required, given the absence of
any Tegra graphics support. I2C muxing will be supported later.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This I2C bus is used for EDID/DDC reads and other "slow" I2C devices.
This requires a 100KHz SCL (clock) rate.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add the device info for ALS and proximity sensor for tegra
boards cardhu, ventana and seaboard.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: s/PZ02/PZ2/ in .dts files, s/seabridge/seaboard/ in commit
description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Pull ARM fixes from Russell King.
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7406/1: hotplug: copy the affinity mask when forcefully migrating IRQs
ARM: 7405/1: kexec: call platform_cpu_kill on the killer rather than the victim
ARM: 7403/1: tls: remove covert channel via TPIDRURW
ARM: 7401/1: mm: Fix section mismatches
ARM: OMAP: fix DMA vs memory ordering
ARM: 7390/1: dts: versatile-pb/ab fix MMC IRQs
ARM: 7400/1: vfp: clear fpscr length and stride bits on entry to sig handler
ARM: 7399/1: vfp: move user vfp state save/restore code out of signal.c
ARM: 7398/1: l2x0: only write to debug registers on PL310
ARM: 7397/1: l2x0: only apply workaround for erratum #753970 on PL310
ARM: 7396/1: errata: only handle ARM erratum #326103 on affected cores
Added AT91SAM9N12 SoC DT file, as well as the board definition
.dts file for AT91SAM9N12-EK.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Ensure that the USB ULPI signals are not tri-stated, and have no pull-
up or pull-down.
Ensure that the pingroup hosting the USB ULPI reset signal (GPIO PV0 or
PV1 depending on the board, so UAC) is not tri-stated, and has no pull-
up or pull-down.
This change appears larger than it is due to the grouping and sorting of
the pin configuration data.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
ULPI PHYs have a reset signal, and different boards use a different GPIO
for this task. Add a property to device tree to represent this.
I'm not sure if adding this property to the EHCI controller node is
entirely correct; perhaps eventually we should have explicit separate
nodes for the various PHYs. However, we don't have that right now, so this
binding seems like a reasonable choice.
Cc: <devicetree-discuss@lists.ozlabs.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add WM8903 codec nodes, and top-level sound complex node for basic
analog audio over headset jack and internal speakers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
This patch adds the information required for successful
registration of the PRCMU timer 4 (clocksource) driver to the
db8500 Device Tree include file.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Here we split the description of the external-bus@50000000 over
two description files. In the more generic db8500 description file
we only specify the external-bus. Normally this would be used to
communicate with a NOR-flash device. On the Snowball however, the
SMSC9115 Ethernet chip occupies it. In the Snowball board specific
description file is where we actually specify that it is in fact the
Ethernet device which lives here.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As of
commit 75294957be
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Feb 14 14:06:57 2012 -0700
irq_domain: Remove 'new' irq_domain in favour of the ppc one
the ARM gic controller uses proper irq domains. Fix the MSM gic
initialization and DT so that it works again.
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
The MMCI driver will not work without two IRQs since this is not
flagged as a single-irq variant. Looking through the complex IRQ
definition for the MMCI on the versatile (including an #if 1
statement forcing MMCI IRQ0 to the VIC) this appears to the the
correct IRQ number for both models.
Cc: Niklas Hernaeus <niklas.hernaeus@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure each button is individually identifiable by using
their correct unique given device names.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This creates Device Tree bindings for the Nomadik GPIO driver.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Split off from the patch actually implementing the bindings]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is believed that the gpio compatible match entry is too long
and cumbersome in its current form. This patch takes steps to
decrease its length by using ST-Microelectronics' abbreviation ST.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is believed that the i2c compatible match entry is too long
and cumbersome in its current form. This patch takes steps to
decrease its length by using ST-Microelectronics' abbreviation ST.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both SPEAr3xx and SPEAr6xx families have one instance of ARM PL080 DMA
controller. This patch adds in support for that.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
This patch adds a generic target for SPEAr3xx machines that can be configured
via the device-tree. Currently the following devices are supported via the
devicetree:
- VIC interrupts
- PL011 UART
- PL061 GPIO
- PL110 CLCD
- SP805 WDT
- Synopsys DW I2C
- Synopsys DW ethernet
- ST FSMC-NAND
- ST SPEAR-SMI
- ST SPEAR-KEYBOARD
- ST SPEAR-RTC
- ARASAN SDHCI-SPEAR
- SPEAR-EHCI
- SPEAR-OHCI
Other peripheral devices will follow in later patches.
This also removes IO_ADDRESS macro and creates 16 MB static mappings instead of
4K for individual peripherals. This is done to have efficient TLB lookup for any
I/O windows that are located closely together. ioremap() on this range will
return this mapping only instead of creating another.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
This patch adds the dts files for the reference machine of LPC32xx:
* arch/arm/boot/dts/lpc32xx.dtsi: Include for devices based on LPC32xx
* arch/arm/boot/dts/phy3250.dts: Board support for PHYTEC phyCORE-LPC3250
Signed-off-by: Roland Stigge <stigge@antcom.de>
This patch adds support for the kizbox board (based on at91sam9g20 SoC)
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
