Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
UV systems can be partitioned into multiple independent SSIs.
Large partitioned systems may have extra bits in the node_id
register. These bits are used when the total memory on all SSIs
exceeds 16TB. These extra bits need to be ignored when
calculating x2apic_extra_bits.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20101130195926.972776133@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Early in boot, reading MMRs from the UV hub controller require
calls to early_ioremap()/early_iounmap(). Rather than
duplicating code, add a common function to do the
map/read/unmap.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20101130195926.834804371@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32: Make sure we can map all of lowmem if we need to
x86, vt-d: Handle previous faults after enabling fault handling
x86: Enable the intr-remap fault handling after local APIC setup
x86, vt-d: Fix the vt-d fault handling irq migration in the x2apic mode
x86, vt-d: Quirk for masking vtd spec errors to platform error handling logic
x86, xsave: Use alloc_bootmem_align() instead of alloc_bootmem()
bootmem: Add alloc_bootmem_align()
x86, gcc-4.6: Use gcc -m options when building vdso
x86: HPET: Chose a paranoid safe value for the ETIME check
x86: io_apic: Avoid unused variable warning when CONFIG_GENERIC_PENDING_IRQ=n
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix off by one in perf_swevent_init()
perf: Fix duplicate events with multiple-pmu vs software events
ftrace: Have recordmcount honor endianness in fn_ELF_R_INFO
scripts/tags.sh: Add magic for trace-events
tracing: Fix panic when lseek() called on "trace" opened for writing
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86: avoid high BIOS area when allocating address space
x86: avoid E820 regions when allocating address space
x86: avoid low BIOS area when allocating address space
resources: add arch hook for preventing allocation in reserved areas
Revert "resources: support allocating space within a region from the top down"
Revert "PCI: allocate bus resources from the top down"
Revert "x86/PCI: allocate space from the end of a region, not the beginning"
Revert "x86: allocate space within a region top-down"
Revert "PCI: fix pci_bus_alloc_resource() hang, prefer positive decode"
PCI: Update MCP55 quirk to not affect non HyperTransport variants
Keep the crash kernel address below 512 MiB for 32 bits and 896 MiB
for 64 bits. For 32 bits, this retains compatibility with earlier
kernel releases, and makes it work even if the vmalloc= setting is
adjusted.
For 64 bits, we should be able to increase this substantially once a
hard-coded limit in kexec-tools is fixed.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20101217195035.GE14502@redhat.com>
This prevents allocation of the last 2MB before 4GB.
The experiment described here shows Windows 7 ignoring the last 1MB:
https://bugzilla.kernel.org/show_bug.cgi?id=23542#c27
This patch ignores the top 2MB instead of just 1MB because H. Peter Anvin
says "There will be ROM at the top of the 32-bit address space; it's a fact
of the architecture, and on at least older systems it was common to have a
shadow 1 MiB below."
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When we allocate address space, e.g., to assign it to a PCI device, don't
allocate anything mentioned in the BIOS E820 memory map.
On recent machines (2008 and newer), we assign PCI resources from the
windows described by the ACPI PCI host bridge _CRS. On many Dell
machines, these windows overlap some E820 reserved areas, e.g.,
BIOS-e820: 00000000bfe4dc00 - 00000000c0000000 (reserved)
pci_root PNP0A03:00: host bridge window [mem 0xbff00000-0xdfffffff]
If we put devices at 0xbff00000, they don't work, probably because
that's really RAM, not I/O memory. This patch prevents that by removing
the 0xbfe4dc00-0xbfffffff area from the "available" resource.
I'm not very happy with this solution because Windows solves the problem
differently (it seems to ignore E820 reserved areas and it allocates
top-down instead of bottom-up; details at comment 45 of the bugzilla
below). That means we're vulnerable to BIOS defects that Windows would not
trip over. For example, if BIOS described a device in ACPI but didn't
mention it in E820, Windows would work fine but Linux would fail.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=16228
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This implements arch_remove_reservations() so allocate_resource() can
avoid any arch-specific reserved areas. This currently just avoids the
BIOS area (the first 1MB), but could be used for E820 reserved areas if
that turns out to be necessary.
We previously avoided this area in pcibios_align_resource(). This patch
moves the test from that PCI-specific path to a generic path, so *all*
resource allocations will avoid this area.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
A relocatable kernel can be anywhere in lowmem -- and in the case of a
kdump kernel, is likely to be fairly high. Since the early page
tables map everything from address zero up we need to make sure we
allocate enough brk that we can map all of lowmem if we need to.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Tested-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4D0AD3ED.8070607@kernel.org>
Extend the perf_pmu_register() interface to allow for named and
dynamic pmu types.
Because we need to support the existing static types we cannot use
dynamic types for everything, hence provide a type argument.
If we want to enumerate the PMUs they need a name, provide one.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20101117222056.259707703@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some BIOSes use PMU resources, which can cause various bugs:
- Non-working or erratic PMU based statistics - the PMU can end up
counting the wrong thing, resulting in misleading statistics
- Profiling can stop working or it can profile the wrong thing
- A non-working or erratic NMI watchdog that cannot be relied on
- The kernel may disturb whatever thing the BIOS tries to use the
PMU for - possibly causing hardware malfunction in extreme cases.
- ... and other forms of potential misbehavior
Various forms of such misbehavior has been observed in practice - there are
BIOSes that just corrupt the PMU state, consequences be damned.
The PMU is a CPU resource that is handled by the kernel and the BIOS
stealing+corrupting it is not acceptable nor robust, so we detect it,
warn about it and further refuse to touch the PMU ourselves.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Two x86 patches broke lguest:
1) v2.6.35-492-g72d7c3b, which changed x86 to use the memblock allocator.
In lguest, the host places linear page tables at the top of mem, which
used to be enough to get us up to the swapper_pg_dir page tables. With
the first patch, the direct mapping tables used that memory:
Before: kernel direct mapping tables up to 4000000 @ 7000-1a000
After: kernel direct mapping tables up to 4000000 @ 3fed000-4000000
I initially fixed this by lying about the amount of memory we had, so
the kernel wouldn't blatt the lguest boot pagetables (yuk!), but then...
2) v2.6.36-rc8-54-gb40827f, which made x86 boot use initial_page_table.
This was initialized in a part of head_32.S which isn't executed by
lguest; it is then copied into swapper_pg_dir. So we have to initialize
it; and anyway we switch to it before we blatt the old tables, so that
fixes the previous damage as well.
For the moment, I cut & pasted the code into lguest's boot code, but
next merge window I will merge them.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
To: x86@kernel.org
- Define a stub irq_create_of_mapping for x86 as a stop-gap solution until
drivers/of/irq is further along.
- Define irq_dispose_mapping for x86 to appease of_i2c.c
These are needed to allow stuff in drivers/of/ to build on x86. This stuff
will eventually get replaced; quoting Grant,
"The long term plan is to have the drivers/of/ code handling the mapping
intelligently like powerpc currently does." But for now, just provide
these functions.
Signed-off-by: Andres Salomon <dilinger@queued.net>
LKML-Reference: <20101111214526.5de7121b@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Interrupt-remapping gets enabled very early in the boot, as it determines the
apic mode that the processor can use. And the current code enables the vt-d
fault handling before the setup_local_APIC(). And hence the APIC LDR registers
and data structure in the memory may not be initialized. So the vt-d fault
handling in logical xapic/x2apic modes were broken.
Fix this by enabling the vt-d fault handling in the end_local_APIC_setup()
A cleaner fix of enabling fault handling while enabling intr-remapping
will be addressed for v2.6.38. [ Enabling intr-remapping determines the
usage of x2apic mode and the apic mode determines the fault-handling
configuration. ]
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
LKML-Reference: <20101201062244.541996375@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: stable@kernel.org [v2.6.32+]
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
In x2apic mode, we need to set the upper address register of the fault
handling interrupt register of the vt-d hardware. Without this
irq migration of the vt-d fault handling interrupt is broken.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
LKML-Reference: <1291225233.2648.39.camel@sbsiddha-MOBL3>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: stable@kernel.org [v2.6.32+]
Acked-by: Chris Wright <chrisw@sous-sol.org>
Tested-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
During suspend, we disable all the non boot cpus. And during resume we bring
them all back again. So no need to do alternatives_smp_switch() in between.
On my core 2 based laptop, this speeds up the suspend path by 15msec and the
resume path by 5 msec (suspend/resume speed up differences can be attributed
to the different P-states that the cpu is in during suspend/resume).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1290557500.4946.8.camel@sbsiddha-MOBL3.sc.intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Alignment of alloc_bootmem() depends on the value of
L1_CACHE_SHIFT. What we need here, however, is 64 byte alignment. Use
alloc_bootmem_align() and explicitly specify the alignment instead.
This fixes a kernel boot crash reported by Jody when the cpu in .config
is set to MPENTIUMII but the kernel is booted on a xsave-capable CPU.
Reported-by: Jody Bruchon <jody@nctritech.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20101116212442.059967454@sbsiddha-MOBL3.sc.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@kernel.org>
commit 995bd3bb5 (x86: Hpet: Avoid the comparator readback penalty)
chose 8 HPET cycles as a safe value for the ETIME check, as we had the
confirmation that the posted write to the comparator register is
delayed by two HPET clock cycles on Intel chipsets which showed
readback problems.
After that patch hit mainline we got reports from machines with newer
AMD chipsets which seem to have an even longer delay. See
http://thread.gmane.org/gmane.linux.kernel/1054283 and
http://thread.gmane.org/gmane.linux.kernel/1069458 for further
information.
Boris tried to come up with an ACPI based selection of the minimum
HPET cycles, but this failed on a couple of test machines. And of
course we did not get any useful information from the hardware folks.
For now our only option is to chose a paranoid high and safe value for
the minimum HPET cycles used by the ETIME check. Adjust the minimum ns
value for the HPET clockevent accordingly.
Reported-Bistected-and-Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <alpine.LFD.2.00.1012131222420.2653@localhost6.localdomain6>
Cc: Simon Kirby <sim@hostway.ca>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andreas Herrmann <Andreas.Herrmann3@amd.com>
Cc: John Stultz <johnstul@us.ibm.com>
The delayed TSC init function does not check whether the system has no
TSC or TSC is disabled at the kernel command line, which results in a
crash in the work queue based extended calibration due to division by
zero because the basic calibration never happened.
Add the missing checks and do not touch TSC when not available or
disabled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <johnstul@us.ibm.com>
setup_local_APIC() is used to setup local APIC early during CPU
initialization and already assumes that preemption is disabled on
entry. However, The function unnecessarily disables and enables
preemption and uses smp_processor_id() multiple times in and out of
the nested preemption disabled section. This gives the wrong
impression that the function might be able to handle being called with
preemption enabled and/or migrated to another processor in the middle.
Make it clear that the function is always called with preemption
disabled, drop the confusing preemption disable block and call
smp_processor_id() once at the beginning of the function.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Cyrill Gorcunov <gorcunov@gmail.com>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: brgerst@gmail.com
LKML-Reference: <4D00B3B9.7060702@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Originally adapted from Huang Ying's patch which moved the
unknown_nmi_panic to the traps.c file. Because the old nmi
watchdog was deleted before this change happened, the
unknown_nmi_panic sysctl was lost. This re-adds it.
Also, the nmi_watchdog sysctl was re-implemented and its
documentation updated accordingly.
Patch-inspired-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: fweisbec@gmail.com
LKML-Reference: <1291068437-5331-3-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
assign_to_mp_irq() is copying the struct mpc_intsrc members one by
one. That's silly. Use memcpy() and let the compiler figure it out.
Same for the identical function assign_to_mpc_intsrc()
mp_irq_mpc_intsrc_cmp() is comparing the struct members one by one,
but no caller ever checks the different return codes. Use memcmp()
instead.
Remove the extra printk in MP_ioapic_info()
Signed-off-by: Feng Tang <feng.tang@linux.intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Alan Cox <alan@linux.intel.com>
Cc: Len Brown <len.brown@intel.com>
LKML-Reference: <20101208151857.212f0018@feng-i7>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There are 3 places defining similar functions of saving IRQ vector
info into mp_irqs[] array: mmparse/acpi/mrst.
Replace the redundant code by a common function in io_apic.c as it's
only called when CONFIG_X86_IO_APIC=y
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20101207133204.4d913c5a@feng-i7>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For 32bit mptable path, setup_ids_from_mpc() always writes the io_apic
id register, even there is no change needed.
Skip the write, when readout and mptable match.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
LKML-Reference: <4CFDF785.7010401@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reason: apic cleanup series depends on x86/apic, x86/amd-nb x86/platform
Conflicts:
arch/x86/include/asm/io_apic.h
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arch/x86/kernel/apic/hw_nmi.c:29: warning: backtrace_mask defined but not used
commit 0e2af2a9(x86, hw_nmi: Move backtrace_mask declaration under
ARCH_HAS_NMI_WATCHDOG) addressed this warning, but it was reintroduced
by commit 5f2b0ba4(x86, nmi_watchdog: Remove the old nmi_watchdog).
Move backtrace_mask into the #ifdef arch_trigger_all_cpu_backtrace
section again.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <AANLkTi=rcc38QzoKa6LFy4m++-p_9=Zt4_kDQE=GeKxf@mail.gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since all the hotplug stuff is serialized by the hotplug mutex,
do away with the amd_nb_lock.
Cc: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/pvclock: Zero last_value on resume
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf record: Fix eternal wait for stillborn child
perf header: Don't assume there's no attr info if no sample ids is provided
perf symbols: Figure out start address of kernel map from kallsyms
perf symbols: Fix kallsyms kernel/module map splitting
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nohz: Fix printk_needs_cpu() return value on offline cpus
printk: Fix wake_up_klogd() vs cpu hotplug
Use text_poke_smp_batch() in optimization path for reducing
the number of stop_machine() issues. If the number of optimizing
probes is more than MAX_OPTIMIZE_PROBES(=256), kprobes optimizes
first MAX_OPTIMIZE_PROBES probes and kicks optimizer for
remaining probes.
Changes in v5:
- Use kick_kprobe_optimizer() instead of directly calling
schedule_delayed_work().
- Rescheduling optimizer outside of kprobe mutex lock.
Changes in v2:
- Allocate code buffer and parameters in arch_init_kprobes()
instead of using static arraies.
- Merge previous max optimization limit patch into this patch.
So, this patch introduces upper limit of optimization at
once.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: 2nddept-manager@sdl.hitachi.co.jp
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <20101203095428.2961.8994.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Unoptimization occurs when a probe is unregistered or disabled,
and is heavy because it recovers instructions by using
stop_machine(). This patch delays unoptimization operations and
unoptimize several probes at once by using
text_poke_smp_batch(). This can avoid unexpected system slowdown
coming from stop_machine().
Changes in v5:
- Split this patch into several cleanup patches and this patch.
- Fix some text_mutex lock miss.
- Use bool instead of int for behavior flags.
- Add additional comment for (un)optimizing path.
Changes in v2:
- Use dynamic allocated buffers and params.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: 2nddept-manager@sdl.hitachi.co.jp
LKML-Reference: <20101203095409.2961.82733.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
