Changes in 5.10.69
PCI: pci-bridge-emul: Add PCIe Root Capabilities Register
PCI: aardvark: Fix reporting CRS value
console: consume APC, DM, DCS
s390/pci_mmio: fully validate the VMA before calling follow_pte()
ARM: Qualify enabling of swiotlb_init()
ARM: 9077/1: PLT: Move struct plt_entries definition to header
ARM: 9078/1: Add warn suppress parameter to arm_gen_branch_link()
ARM: 9079/1: ftrace: Add MODULE_PLTS support
ARM: 9098/1: ftrace: MODULE_PLT: Fix build problem without DYNAMIC_FTRACE
Revert "net/mlx5: Register to devlink ingress VLAN filter trap"
sctp: validate chunk size in __rcv_asconf_lookup
sctp: add param size validation for SCTP_PARAM_SET_PRIMARY
staging: rtl8192u: Fix bitwise vs logical operator in TranslateRxSignalStuff819xUsb()
coredump: fix memleak in dump_vma_snapshot()
um: virtio_uml: fix memory leak on init failures
dmaengine: acpi: Avoid comparison GSI with Linux vIRQ
perf test: Fix bpf test sample mismatch reporting
tools lib: Adopt memchr_inv() from kernel
perf tools: Allow build-id with trailing zeros
thermal/drivers/exynos: Fix an error code in exynos_tmu_probe()
9p/trans_virtio: Remove sysfs file on probe failure
prctl: allow to setup brk for et_dyn executables
nilfs2: use refcount_dec_and_lock() to fix potential UAF
profiling: fix shift-out-of-bounds bugs
PM: sleep: core: Avoid setting power.must_resume to false
pwm: lpc32xx: Don't modify HW state in .probe() after the PWM chip was registered
pwm: mxs: Don't modify HW state in .probe() after the PWM chip was registered
dmaengine: idxd: fix wq slot allocation index check
platform/chrome: sensorhub: Add trace events for sample
platform/chrome: cros_ec_trace: Fix format warnings
ceph: allow ceph_put_mds_session to take NULL or ERR_PTR
ceph: cancel delayed work instead of flushing on mdsc teardown
Kconfig.debug: drop selecting non-existing HARDLOCKUP_DETECTOR_ARCH
tools/bootconfig: Fix tracing_on option checking in ftrace2bconf.sh
thermal/core: Fix thermal_cooling_device_register() prototype
drm/amdgpu: Disable PCIE_DPM on Intel RKL Platform
drivers: base: cacheinfo: Get rid of DEFINE_SMP_CALL_CACHE_FUNCTION()
dma-buf: DMABUF_MOVE_NOTIFY should depend on DMA_SHARED_BUFFER
parisc: Move pci_dev_is_behind_card_dino to where it is used
iommu/amd: Relocate GAMSup check to early_enable_iommus
dmaengine: idxd: depends on !UML
dmaengine: sprd: Add missing MODULE_DEVICE_TABLE
dmaengine: ioat: depends on !UML
dmaengine: xilinx_dma: Set DMA mask for coherent APIs
ceph: request Fw caps before updating the mtime in ceph_write_iter
ceph: remove the capsnaps when removing caps
ceph: lockdep annotations for try_nonblocking_invalidate
btrfs: update the bdev time directly when closing
btrfs: fix lockdep warning while mounting sprout fs
nilfs2: fix memory leak in nilfs_sysfs_create_device_group
nilfs2: fix NULL pointer in nilfs_##name##_attr_release
nilfs2: fix memory leak in nilfs_sysfs_create_##name##_group
nilfs2: fix memory leak in nilfs_sysfs_delete_##name##_group
nilfs2: fix memory leak in nilfs_sysfs_create_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_delete_snapshot_group
habanalabs: add validity check for event ID received from F/W
pwm: img: Don't modify HW state in .remove() callback
pwm: rockchip: Don't modify HW state in .remove() callback
pwm: stm32-lp: Don't modify HW state in .remove() callback
blk-throttle: fix UAF by deleteing timer in blk_throtl_exit()
blk-mq: allow 4x BLK_MAX_REQUEST_COUNT at blk_plug for multiple_queues
rtc: rx8010: select REGMAP_I2C
sched/idle: Make the idle timer expire in hard interrupt context
drm/nouveau/nvkm: Replace -ENOSYS with -ENODEV
Linux 5.10.69
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: I982349e3a65b83e92e9b808154bf8c84d094f1d6
commit e1fbbd073137a9d63279f6bf363151a938347640 upstream.
Keno Fischer reported that when a binray loaded via ld-linux-x the
prctl(PR_SET_MM_MAP) doesn't allow to setup brk value because it lays
before mm:end_data.
For example a test program shows
| # ~/t
|
| start_code 401000
| end_code 401a15
| start_stack 7ffce4577dd0
| start_data 403e10
| end_data 40408c
| start_brk b5b000
| sbrk(0) b5b000
and when executed via ld-linux
| # /lib64/ld-linux-x86-64.so.2 ~/t
|
| start_code 7fc25b0a4000
| end_code 7fc25b0c4524
| start_stack 7fffcc6b2400
| start_data 7fc25b0ce4c0
| end_data 7fc25b0cff98
| start_brk 55555710c000
| sbrk(0) 55555710c000
This of course prevent criu from restoring such programs. Looking into
how kernel operates with brk/start_brk inside brk() syscall I don't see
any problem if we allow to setup brk/start_brk without checking for
end_data. Even if someone pass some weird address here on a purpose then
the worst possible result will be an unexpected unmapping of existing vma
(own vma, since prctl works with the callers memory) but test for
RLIMIT_DATA is still valid and a user won't be able to gain more memory in
case of expanding VMAs via new values shipped with prctl call.
Link: https://lkml.kernel.org/r/20210121221207.GB2174@grain
Fixes: bbdc6076d2 ("binfmt_elf: move brk out of mmap when doing direct loader exec")
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Reported-by: Keno Fischer <keno@juliacomputing.com>
Acked-by: Andrey Vagin <avagin@gmail.com>
Tested-by: Andrey Vagin <avagin@gmail.com>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change introduces a prctl that allows the user program to control
which PAC keys are enabled in a particular task. The main reason
why this is useful is to enable a userspace ABI that uses PAC to
sign and authenticate function pointers and other pointers exposed
outside of the function, while still allowing binaries conforming
to the ABI to interoperate with legacy binaries that do not sign or
authenticate pointers.
The idea is that a dynamic loader or early startup code would issue
this prctl very early after establishing that a process may load legacy
binaries, but before executing any PAC instructions.
This change adds a small amount of overhead to kernel entry and exit
due to additional required instruction sequences.
On a DragonBoard 845c (Cortex-A75) with the powersave governor, the
overhead of similar instruction sequences was measured as 4.9ns when
simulating the common case where IA is left enabled, or 43.7ns when
simulating the uncommon case where IA is disabled. These numbers can
be seen as the worst case scenario, since in more realistic scenarios
a better performing governor would be used and a newer chip would be
used that would support PAC unlike Cortex-A75 and would be expected
to be faster than Cortex-A75.
On an Apple M1 under a hypervisor, the overhead of the entry/exit
instruction sequences introduced by this patch was measured as 0.3ns
in the case where IA is left enabled, and 33.0ns in the case where
IA is disabled.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Link: https://linux-review.googlesource.com/id/Ibc41a5e6a76b275efbaa126b31119dc197b927a5
Link: https://lore.kernel.org/r/d6609065f8f40397a4124654eb68c9f490b4d477.1616123271.git.pcc@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Bug: 192536783
(cherry picked from commit 201698626fbca1cf1a3b686ba14cf2a056500716)
Change-Id: Ic0a21c92a22575f9ec3599fb67bd2931a50b9f04
[quic_eberman@quicinc.com: Resolved merge conflict in
arch/arm64/kernel/process.c]
Signed-off-by: Elliot Berman <quic_eberman@quicinc.com>
Signed-off-by: Peter Collingbourne <pcc@google.com>
[ Upstream commit 905ae01c4ae2ae3df05bb141801b1db4b7d83c61 ]
For RLIMIT_NPROC and some other rlimits the user_struct that holds the
global limit is kept alive for the lifetime of a process by keeping it
in struct cred. Adding a pointer to ucounts in the struct cred will
allow to track RLIMIT_NPROC not only for user in the system, but for
user in the user_namespace.
Updating ucounts may require memory allocation which may fail. So, we
cannot change cred.ucounts in the commit_creds() because this function
cannot fail and it should always return 0. For this reason, we modify
cred.ucounts before calling the commit_creds().
Changelog
v6:
* Fix null-ptr-deref in is_ucounts_overlimit() detected by trinity. This
error was caused by the fact that cred_alloc_blank() left the ucounts
pointer empty.
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Alexey Gladkov <legion@kernel.org>
Link: https://lkml.kernel.org/r/b37aaef28d8b9b0d757e07ba6dd27281bbe39259.1619094428.git.legion@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Steps on the way to 5.10-rc1
Resolves conflicts in:
fs/userfaultfd.c
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: Ie3fe3c818f1f6565cfd4fa551de72d2b72ef60af
tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace". So
sparse rightfully complains about passing a kernel pointer to
put_user().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull SafeSetID updates from Micah Morton:
"The changes are mostly contained to within the SafeSetID LSM, with the
exception of a few 1-line changes to change some ns_capable() calls to
ns_capable_setid() -- causing a flag (CAP_OPT_INSETID) to be set that
is examined by SafeSetID code and nothing else in the kernel.
The changes to SafeSetID internally allow for setting up GID
transition security policies, as already existed for UIDs"
* tag 'safesetid-5.10' of git://github.com/micah-morton/linux:
LSM: SafeSetID: Fix warnings reported by test bot
LSM: SafeSetID: Add GID security policy handling
LSM: Signal to SafeSetID when setting group IDs
For SafeSetID to properly gate set*gid() calls, it needs to know whether
ns_capable() is being called from within a sys_set*gid() function or is
being called from elsewhere in the kernel. This allows SafeSetID to deny
CAP_SETGID to restricted groups when they are attempting to use the
capability for code paths other than updating GIDs (e.g. setting up
userns GID mappings). This is the identical approach to what is
currently done for CAP_SETUID.
NOTE: We also add signaling to SafeSetID from the setgroups() syscall,
as we have future plans to restrict a process' ability to set
supplementary groups in addition to what is added in this series for
restricting setting of the primary group.
Signed-off-by: Thomas Cedeno <thomascedeno@google.com>
Signed-off-by: Micah Morton <mortonm@chromium.org>
Steps on the way to 5.9-rc1
Resolves conflicts in:
drivers/irqchip/qcom-pdc.c
include/linux/device.h
net/xfrm/xfrm_state.c
security/lsm_audit.c
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: I4aeb3d04f4717714a421721eb3ce690c099bb30a
Originally, only a local CAP_SYS_ADMIN could change the exe link,
making it difficult for doing checkpoint/restore without CAP_SYS_ADMIN.
This commit adds CAP_CHECKPOINT_RESTORE in addition to CAP_SYS_ADMIN
for permitting changing the exe link.
The following describes the history of the /proc/self/exe permission
checks as it may be difficult to understand what decisions lead to this
point.
* [1] May 2012: This commit introduces the ability of changing
/proc/self/exe if the user is CAP_SYS_RESOURCE capable.
In the related discussion [2], no clear thread model is presented for
what could happen if the /proc/self/exe changes multiple times, or why
would the admin be at the mercy of userspace.
* [3] Oct 2014: This commit introduces a new API to change
/proc/self/exe. The permission no longer checks for CAP_SYS_RESOURCE,
but instead checks if the current user is root (uid=0) in its local
namespace. In the related discussion [4] it is said that "Controlling
exe_fd without privileges may turn out to be dangerous. At least
things like tomoyo examine it for making policy decisions (see
tomoyo_manager())."
* [5] Dec 2016: This commit removes the restriction to change
/proc/self/exe at most once. The related discussion [6] informs that
the audit subsystem relies on the exe symlink, presumably
audit_log_d_path_exe() in kernel/audit.c.
* [7] May 2017: This commit changed the check from uid==0 to local
CAP_SYS_ADMIN. No discussion.
* [8] July 2020: A PoC to spoof any program's /proc/self/exe via ptrace
is demonstrated
Overall, the concrete points that were made to retain capability checks
around changing the exe symlink is that tomoyo_manager() and
audit_log_d_path_exe() uses the exe_file path.
Christian Brauner said that relying on /proc/<pid>/exe being immutable (or
guarded by caps) in a sake of security is a bit misleading. It can only
be used as a hint without any guarantees of what code is being executed
once execve() returns to userspace. Christian suggested that in the
future, we could call audit_log() or similar to inform the admin of all
exe link changes, instead of attempting to provide security guarantees
via permission checks. However, this proposed change requires the
understanding of the security implications in the tomoyo/audit subsystems.
[1] b32dfe3771 ("c/r: prctl: add ability to set new mm_struct::exe_file")
[2] https://lore.kernel.org/patchwork/patch/292515/
[3] f606b77f1a ("prctl: PR_SET_MM -- introduce PR_SET_MM_MAP operation")
[4] https://lore.kernel.org/patchwork/patch/479359/
[5] 3fb4afd9a5 ("prctl: remove one-shot limitation for changing exe link")
[6] https://lore.kernel.org/patchwork/patch/697304/
[7] 4d28df6152 ("prctl: Allow local CAP_SYS_ADMIN changing exe_file")
[8] https://github.com/nviennot/run_as_exe
Signed-off-by: Nicolas Viennot <Nicolas.Viennot@twosigma.com>
Signed-off-by: Adrian Reber <areber@redhat.com>
Link: https://lore.kernel.org/r/20200719100418.2112740-6-areber@redhat.com
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
It's now being abstracted away, so fix up the ANDROID specific code that
touches the lock to use the correct functions instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: I9cedb62118cd1bba7af27deb11499d312d24d7fc
Pull SafeSetID update from Micah Morton:
"Add additional LSM hooks for SafeSetID
SafeSetID is capable of making allow/deny decisions for set*uid calls
on a system, and we want to add similar functionality for set*gid
calls.
The work to do that is not yet complete, so probably won't make it in
for v5.8, but we are looking to get this simple patch in for v5.8
since we have it ready.
We are planning on the rest of the work for extending the SafeSetID
LSM being merged during the v5.9 merge window"
* tag 'LSM-add-setgid-hook-5.8-author-fix' of git://github.com/micah-morton/linux:
security: Add LSM hooks to set*gid syscalls
The SafeSetID LSM uses the security_task_fix_setuid hook to filter
set*uid() syscalls according to its configured security policy. In
preparation for adding analagous support in the LSM for set*gid()
syscalls, we add the requisite hook here. Tested by putting print
statements in the security_task_fix_setgid hook and seeing them get hit
during kernel boot.
Signed-off-by: Thomas Cedeno <thomascedeno@google.com>
Signed-off-by: Micah Morton <mortonm@chromium.org>
Tiny merge resolutions along the way to 5.8-rc1.
Change-Id: I24b3cca28ed36f32c92b6374dae5d7f006d3bced
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Merge updates from Andrew Morton:
"A few little subsystems and a start of a lot of MM patches.
Subsystems affected by this patch series: squashfs, ocfs2, parisc,
vfs. With mm subsystems: slab-generic, slub, debug, pagecache, gup,
swap, memcg, pagemap, memory-failure, vmalloc, kasan"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (128 commits)
kasan: move kasan_report() into report.c
mm/mm_init.c: report kasan-tag information stored in page->flags
ubsan: entirely disable alignment checks under UBSAN_TRAP
kasan: fix clang compilation warning due to stack protector
x86/mm: remove vmalloc faulting
mm: remove vmalloc_sync_(un)mappings()
x86/mm/32: implement arch_sync_kernel_mappings()
x86/mm/64: implement arch_sync_kernel_mappings()
mm/ioremap: track which page-table levels were modified
mm/vmalloc: track which page-table levels were modified
mm: add functions to track page directory modifications
s390: use __vmalloc_node in stack_alloc
powerpc: use __vmalloc_node in alloc_vm_stack
arm64: use __vmalloc_node in arch_alloc_vmap_stack
mm: remove vmalloc_user_node_flags
mm: switch the test_vmalloc module to use __vmalloc_node
mm: remove __vmalloc_node_flags_caller
mm: remove both instances of __vmalloc_node_flags
mm: remove the prot argument to __vmalloc_node
mm: remove the pgprot argument to __vmalloc
...
PF_LESS_THROTTLE exists for loop-back nfsd (and a similar need in the
loop block driver and callers of prctl(PR_SET_IO_FLUSHER)), where a
daemon needs to write to one bdi (the final bdi) in order to free up
writes queued to another bdi (the client bdi).
The daemon sets PF_LESS_THROTTLE and gets a larger allowance of dirty
pages, so that it can still dirty pages after other processses have been
throttled. The purpose of this is to avoid deadlock that happen when
the PF_LESS_THROTTLE process must write for any dirty pages to be freed,
but it is being thottled and cannot write.
This approach was designed when all threads were blocked equally,
independently on which device they were writing to, or how fast it was.
Since that time the writeback algorithm has changed substantially with
different threads getting different allowances based on non-trivial
heuristics. This means the simple "add 25%" heuristic is no longer
reliable.
The important issue is not that the daemon needs a *larger* dirty page
allowance, but that it needs a *private* dirty page allowance, so that
dirty pages for the "client" bdi that it is helping to clear (the bdi
for an NFS filesystem or loop block device etc) do not affect the
throttling of the daemon writing to the "final" bdi.
This patch changes the heuristic so that the task is not throttled when
the bdi it is writing to has a dirty page count below below (or equal
to) the free-run threshold for that bdi. This ensures it will always be
able to have some pages in flight, and so will not deadlock.
In a steady-state, it is expected that PF_LOCAL_THROTTLE tasks might
still be throttled by global threshold, but that is acceptable as it is
only the deadlock state that is interesting for this flag.
This approach of "only throttle when target bdi is busy" is consistent
with the other use of PF_LESS_THROTTLE in current_may_throttle(), were
it causes attention to be focussed only on the target bdi.
So this patch
- renames PF_LESS_THROTTLE to PF_LOCAL_THROTTLE,
- removes the 25% bonus that that flag gives, and
- If PF_LOCAL_THROTTLE is set, don't delay at all unless the
global and the local free-run thresholds are exceeded.
Note that previously realtime threads were treated the same as
PF_LESS_THROTTLE threads. This patch does *not* change the behvaiour
for real-time threads, so it is now different from the behaviour of nfsd
and loop tasks. I don't know what is wanted for realtime.
[akpm@linux-foundation.org: coding style fixes]
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: Chuck Lever <chuck.lever@oracle.com> [nfsd]
Cc: Christoph Hellwig <hch@lst.de>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Trond Myklebust <trond.myklebust@hammerspace.com>
Link: http://lkml.kernel.org/r/87ftbf7gs3.fsf@notabene.neil.brown.name
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Baby steps in the 5.6-rc1 merge cycle to make things easier to review
and debug.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: I0fa183764fd1adbde44e8181f0b3df6cff4da18b
There are several storage drivers like dm-multipath, iscsi, tcmu-runner,
amd nbd that have userspace components that can run in the IO path. For
example, iscsi and nbd's userspace deamons may need to recreate a socket
and/or send IO on it, and dm-multipath's daemon multipathd may need to
send SG IO or read/write IO to figure out the state of paths and re-set
them up.
In the kernel these drivers have access to GFP_NOIO/GFP_NOFS and the
memalloc_*_save/restore functions to control the allocation behavior,
but for userspace we would end up hitting an allocation that ended up
writing data back to the same device we are trying to allocate for.
The device is then in a state of deadlock, because to execute IO the
device needs to allocate memory, but to allocate memory the memory
layers want execute IO to the device.
Here is an example with nbd using a local userspace daemon that performs
network IO to a remote server. We are using XFS on top of the nbd device,
but it can happen with any FS or other modules layered on top of the nbd
device that can write out data to free memory. Here a nbd daemon helper
thread, msgr-worker-1, is performing a write/sendmsg on a socket to execute
a request. This kicks off a reclaim operation which results in a WRITE to
the nbd device and the nbd thread calling back into the mm layer.
[ 1626.609191] msgr-worker-1 D 0 1026 1 0x00004000
[ 1626.609193] Call Trace:
[ 1626.609195] ? __schedule+0x29b/0x630
[ 1626.609197] ? wait_for_completion+0xe0/0x170
[ 1626.609198] schedule+0x30/0xb0
[ 1626.609200] schedule_timeout+0x1f6/0x2f0
[ 1626.609202] ? blk_finish_plug+0x21/0x2e
[ 1626.609204] ? _xfs_buf_ioapply+0x2e6/0x410
[ 1626.609206] ? wait_for_completion+0xe0/0x170
[ 1626.609208] wait_for_completion+0x108/0x170
[ 1626.609210] ? wake_up_q+0x70/0x70
[ 1626.609212] ? __xfs_buf_submit+0x12e/0x250
[ 1626.609214] ? xfs_bwrite+0x25/0x60
[ 1626.609215] xfs_buf_iowait+0x22/0xf0
[ 1626.609218] __xfs_buf_submit+0x12e/0x250
[ 1626.609220] xfs_bwrite+0x25/0x60
[ 1626.609222] xfs_reclaim_inode+0x2e8/0x310
[ 1626.609224] xfs_reclaim_inodes_ag+0x1b6/0x300
[ 1626.609227] xfs_reclaim_inodes_nr+0x31/0x40
[ 1626.609228] super_cache_scan+0x152/0x1a0
[ 1626.609231] do_shrink_slab+0x12c/0x2d0
[ 1626.609233] shrink_slab+0x9c/0x2a0
[ 1626.609235] shrink_node+0xd7/0x470
[ 1626.609237] do_try_to_free_pages+0xbf/0x380
[ 1626.609240] try_to_free_pages+0xd9/0x1f0
[ 1626.609245] __alloc_pages_slowpath+0x3a4/0xd30
[ 1626.609251] ? ___slab_alloc+0x238/0x560
[ 1626.609254] __alloc_pages_nodemask+0x30c/0x350
[ 1626.609259] skb_page_frag_refill+0x97/0xd0
[ 1626.609274] sk_page_frag_refill+0x1d/0x80
[ 1626.609279] tcp_sendmsg_locked+0x2bb/0xdd0
[ 1626.609304] tcp_sendmsg+0x27/0x40
[ 1626.609307] sock_sendmsg+0x54/0x60
[ 1626.609308] ___sys_sendmsg+0x29f/0x320
[ 1626.609313] ? sock_poll+0x66/0xb0
[ 1626.609318] ? ep_item_poll.isra.15+0x40/0xc0
[ 1626.609320] ? ep_send_events_proc+0xe6/0x230
[ 1626.609322] ? hrtimer_try_to_cancel+0x54/0xf0
[ 1626.609324] ? ep_read_events_proc+0xc0/0xc0
[ 1626.609326] ? _raw_write_unlock_irq+0xa/0x20
[ 1626.609327] ? ep_scan_ready_list.constprop.19+0x218/0x230
[ 1626.609329] ? __hrtimer_init+0xb0/0xb0
[ 1626.609331] ? _raw_spin_unlock_irq+0xa/0x20
[ 1626.609334] ? ep_poll+0x26c/0x4a0
[ 1626.609337] ? tcp_tsq_write.part.54+0xa0/0xa0
[ 1626.609339] ? release_sock+0x43/0x90
[ 1626.609341] ? _raw_spin_unlock_bh+0xa/0x20
[ 1626.609342] __sys_sendmsg+0x47/0x80
[ 1626.609347] do_syscall_64+0x5f/0x1c0
[ 1626.609349] ? prepare_exit_to_usermode+0x75/0xa0
[ 1626.609351] entry_SYSCALL_64_after_hwframe+0x44/0xa9
This patch adds a new prctl command that daemons can use after they have
done their initial setup, and before they start to do allocations that
are in the IO path. It sets the PF_MEMALLOC_NOIO and PF_LESS_THROTTLE
flags so both userspace block and FS threads can use it to avoid the
allocation recursion and try to prevent from being throttled while
writing out data to free up memory.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Masato Suzuki <masato.suzuki@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Link: https://lore.kernel.org/r/20191112001900.9206-1-mchristi@redhat.com
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
There are two 'struct timeval' fields in 'struct rusage'.
Unfortunately the definition of timeval is now ambiguous when used in
user space with a libc that has a 64-bit time_t, and this also changes
the 'rusage' definition in user space in a way that is incompatible with
the system call interface.
While there is no good solution to avoid all ambiguity here, change
the definition in the kernel headers to be compatible with the kernel
ABI, using __kernel_old_timeval as an unambiguous base type.
In previous discussions, there was also a plan to add a replacement
for rusage based on 64-bit timestamps and nanosecond resolution,
i.e. 'struct __kernel_timespec'. I have patches for that as well,
if anyone thinks we should do that.
Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This merges Linus's tree as of commit b41dae061b ("Merge tag
'xfs-5.4-merge-7' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux")
into android-mainline.
This "early" merge makes it easier to test and handle merge conflicts
instead of having to wait until the "end" of the merge window and handle
all 10000+ commits at once.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: I6bebf55e5e2353f814e3c87f5033607b1ae5d812
Pull core timer updates from Thomas Gleixner:
"Timers and timekeeping updates:
- A large overhaul of the posix CPU timer code which is a preparation
for moving the CPU timer expiry out into task work so it can be
properly accounted on the task/process.
An update to the bogus permission checks will come later during the
merge window as feedback was not complete before heading of for
travel.
- Switch the timerqueue code to use cached rbtrees and get rid of the
homebrewn caching of the leftmost node.
- Consolidate hrtimer_init() + hrtimer_init_sleeper() calls into a
single function
- Implement the separation of hrtimers to be forced to expire in hard
interrupt context even when PREEMPT_RT is enabled and mark the
affected timers accordingly.
- Implement a mechanism for hrtimers and the timer wheel to protect
RT against priority inversion and live lock issues when a (hr)timer
which should be canceled is currently executing the callback.
Instead of infinitely spinning, the task which tries to cancel the
timer blocks on a per cpu base expiry lock which is held and
released by the (hr)timer expiry code.
- Enable the Hyper-V TSC page based sched_clock for Hyper-V guests
resulting in faster access to timekeeping functions.
- Updates to various clocksource/clockevent drivers and their device
tree bindings.
- The usual small improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (101 commits)
posix-cpu-timers: Fix permission check regression
posix-cpu-timers: Always clear head pointer on dequeue
hrtimer: Add a missing bracket and hide `migration_base' on !SMP
posix-cpu-timers: Make expiry_active check actually work correctly
posix-timers: Unbreak CONFIG_POSIX_TIMERS=n build
tick: Mark sched_timer to expire in hard interrupt context
hrtimer: Add kernel doc annotation for HRTIMER_MODE_HARD
x86/hyperv: Hide pv_ops access for CONFIG_PARAVIRT=n
posix-cpu-timers: Utilize timerqueue for storage
posix-cpu-timers: Move state tracking to struct posix_cputimers
posix-cpu-timers: Deduplicate rlimit handling
posix-cpu-timers: Remove pointless comparisons
posix-cpu-timers: Get rid of 64bit divisions
posix-cpu-timers: Consolidate timer expiry further
posix-cpu-timers: Get rid of zero checks
rlimit: Rewrite non-sensical RLIMIT_CPU comment
posix-cpu-timers: Respect INFINITY for hard RTTIME limit
posix-cpu-timers: Switch thread group sampling to array
posix-cpu-timers: Restructure expiry array
posix-cpu-timers: Remove cputime_expires
...
Pull x86 cpu-feature updates from Ingo Molnar:
- Rework the Intel model names symbols/macros, which were decades of
ad-hoc extensions and added random noise. It's now a coherent, easy
to follow nomenclature.
- Add new Intel CPU model IDs:
- "Tiger Lake" desktop and mobile models
- "Elkhart Lake" model ID
- and the "Lightning Mountain" variant of Airmont, plus support code
- Add the new AVX512_VP2INTERSECT instruction to cpufeatures
- Remove Intel MPX user-visible APIs and the self-tests, because the
toolchain (gcc) is not supporting it going forward. This is the
first, lowest-risk phase of MPX removal.
- Remove X86_FEATURE_MFENCE_RDTSC
- Various smaller cleanups and fixes
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
x86/cpu: Update init data for new Airmont CPU model
x86/cpu: Add new Airmont variant to Intel family
x86/cpu: Add Elkhart Lake to Intel family
x86/cpu: Add Tiger Lake to Intel family
x86: Correct misc typos
x86/intel: Add common OPTDIFFs
x86/intel: Aggregate microserver naming
x86/intel: Aggregate big core graphics naming
x86/intel: Aggregate big core mobile naming
x86/intel: Aggregate big core client naming
x86/cpufeature: Explain the macro duplication
x86/ftrace: Remove mcount() declaration
x86/PCI: Remove superfluous returns from void functions
x86/msr-index: Move AMD MSRs where they belong
x86/cpu: Use constant definitions for CPU models
lib: Remove redundant ftrace flag removal
x86/crash: Remove unnecessary comparison
x86/bitops: Use __builtin_constant_p() directly instead of IS_IMMEDIATE()
x86: Remove X86_FEATURE_MFENCE_RDTSC
x86/mpx: Remove MPX APIs
...
Deactivation of the expiry cache is done by setting all clock caches to
0. That requires to have a check for zero in all places which update the
expiry cache:
if (cache == 0 || new < cache)
cache = new;
Use U64_MAX as the deactivated value, which allows to remove the zero
checks when updating the cache and reduces it to the obvious check:
if (new < cache)
cache = new;
This also removes the weird workaround in do_prlimit() which was required
to convert a RLIMIT_CPU value of 0 (immediate expiry) to 1 because handing
in 0 to the posix CPU timer code would have effectively disarmed it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lkml.kernel.org/r/20190821192922.275086128@linutronix.de
The comment above the function which arms RLIMIT_CPU in the posix CPU timer
code makes no sense at all. It claims that the kernel does not return an
error code when it rejected the attempt to set RLIMIT_CPU. That's clearly
bogus as the code does an error check and the rlimit is only set and
activated when the permission checks are ok. In case of a rejection an
appropriate error code is returned.
This is a historical and outdated comment which got dragged along even when
the rlimit handling code was rewritten.
Replace it with an explanation why the setup function is not called when
the rlimit value is RLIM_INFINITY and how the 'disarming' is handled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lkml.kernel.org/r/20190821192922.185511287@linutronix.de
Require that arg{3,4,5} of the PR_{SET,GET}_TAGGED_ADDR_CTRL prctl and
arg2 of the PR_GET_TAGGED_ADDR_CTRL prctl() are zero rather than ignored
for future extensions.
Acked-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
It is not desirable to relax the ABI to allow tagged user addresses into
the kernel indiscriminately. This patch introduces a prctl() interface
for enabling or disabling the tagged ABI with a global sysctl control
for preventing applications from enabling the relaxed ABI (meant for
testing user-space prctl() return error checking without reconfiguring
the kernel). The ABI properties are inherited by threads of the same
application and fork()'ed children but cleared on execve(). A Kconfig
option allows the overall disabling of the relaxed ABI.
The PR_SET_TAGGED_ADDR_CTRL will be expanded in the future to handle
MTE-specific settings like imprecise vs precise exceptions.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
MPX is being removed from the kernel due to a lack of support in the
toolchain going forward (gcc).
The first step is to remove the userspace-visible ABIs so that applications
will stop using it. The most visible one are the enable/disable prctl()s.
Remove them first.
This is the most minimal and least invasive change needed to ensure that
apps stop using MPX with new kernels.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190705175321.DB42F0AD@viggo.jf.intel.com
The commit a3b609ef9f ("proc read mm's {arg,env}_{start,end} with mmap
semaphore taken.") added synchronization of reading argument/environment
boundaries under mmap_sem. Later commit 88aa7cc688 ("mm: introduce
arg_lock to protect arg_start|end and env_start|end in mm_struct") avoided
the coarse use of mmap_sem in similar situations. But there still
remained two places that (mis)use mmap_sem.
get_cmdline should also use arg_lock instead of mmap_sem when it reads the
boundaries.
The second place that should use arg_lock is in prctl_set_mm. By
protecting the boundaries fields with the arg_lock, we can downgrade
mmap_sem to reader lock (analogous to what we already do in
prctl_set_mm_map).
[akpm@linux-foundation.org: coding style fixes]
Link: http://lkml.kernel.org/r/20190502125203.24014-3-mkoutny@suse.com
Fixes: 88aa7cc688 ("mm: introduce arg_lock to protect arg_start|end and env_start|end in mm_struct")
Signed-off-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Co-developed-by: Laurent Dufour <ldufour@linux.ibm.com>
Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Yang Shi <yang.shi@linux.alibaba.com>
Cc: Mateusz Guzik <mguzik@redhat.com>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While validating new map we require the @start_data to be strictly less
than @end_data, which is fine for regular applications (this is why this
nit didn't trigger for that long). These members are set from executable
loaders such as elf handers, still it is pretty valid to have a loadable
data section with zero size in file, in such case the start_data is equal
to end_data once kernel loader finishes.
As a result when we're trying to restore such programs the procedure fails
and the kernel returns -EINVAL. From the image dump of a program:
| "mm_start_code": "0x400000",
| "mm_end_code": "0x8f5fb4",
| "mm_start_data": "0xf1bfb0",
| "mm_end_data": "0xf1bfb0",
Thus we need to change validate_prctl_map from strictly less to less or
equal operator use.
Link: http://lkml.kernel.org/r/20190408143554.GY1421@uranus.lan
Fixes: f606b77f1a ("prctl: PR_SET_MM -- introduce PR_SET_MM_MAP operation")
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Andrey Vagin <avagin@gmail.com>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: Pavel Emelyanov <xemul@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
