Kalle Valo says:
====================
wireless-drivers-next patches for v5.10
Second set of patches for v5.10. Biggest change here is wcn3680
support to wcn36xx driver, otherwise smaller features. And naturally
the usual fixes and cleanups.
Major changes:
brcmfmac
* support 4-way handshake offloading for WPA/WPA2-PSK in AP mode
* support SAE authentication offload in AP mode
mt76
* mt7663 runtime power management improvements
* mt7915 A-MSDU offload
wcn36xx
* add support wcn3680 Wi-Fi 5 devices
ath11k
* spectral scan support for ipq6018
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting F2 block size to 128 bytes for BCM4329 allows to significantly
improve RX throughput on NVIDIA Tegra20. Before this change the throughput
was capped to 30 Mbit/s on Tegra, now throughput is at 40 Mbit/s, which is
a maximum throughput for the BCM4329 chip. The F2 block size is borrowed
from the downstream BCMDHD driver. The comment in the BCMDHD driver says
that 128B improves throughput and turns out that it works for the brcmfmac
as well.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200830191439.10017-4-digetx@gmail.com
This patch fixes SDHCI CRC errors during of RX throughput testing on
BCM4329 chip if SDIO BUS is clocked above 25MHz. In particular the
checksum problem is observed on NVIDIA Tegra20 SoCs. The good watermark
value is borrowed from downstream BCMDHD driver and it's matching to the
value that is already used for the BCM4339 chip, hence let's re-use it
for BCM4329.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200830191439.10017-2-digetx@gmail.com
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:16:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_spurwar_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:19036:6: warning: variable ‘tempval’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_tempsense_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:21983:28: warning: variable ‘RfctrlMiscReg6_save’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_rssi_compute_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:22986:6: warning: variable ‘phyRx0_l’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_runsamples_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:23101:6: warning: variable ‘lpf_bw_ctl_miscreg4’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:23100:50: warning: variable ‘lpf_bw_ctl_miscreg3’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_iqcal_gainparams_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:23406:6: warning: variable ‘idx’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_a2_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:24707:7: warning: variable ‘phy_a6’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_a3_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:24999:7: warning: variable ‘phy_a11’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: zhong jiang <zhongjiang@huawei.com>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-29-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:11:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_rx_iq_cal’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1366:29: warning: variable ‘RFOverride0_old’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_radio_2064_channel_tune_4313’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1667:21: warning: variable ‘qFvco’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1667:14: warning: variable ‘qFref’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1667:6: warning: variable ‘qFxtal’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_idle_tssi_est’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:2856:6: warning: variable ‘idleTssi’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_tx_iqlo_soft_cal_full’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:53: warning: variable ‘locc4’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:46: warning: variable ‘locc3’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:39: warning: variable ‘locc2’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:32: warning: variable ‘iqcc0’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_periodic_cal’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4196:6: warning: variable ‘rx_iqcomp_sz’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4195:33: warning: variable ‘rx_iqcomp’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4194:16: warning: variable ‘full_cal’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_phy_txpwr_srom_read_lcnphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4919:7: warning: variable ‘opo’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-28-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'name' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'requested_packet' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'suppr_transit_count' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'send_tim_signal' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'traffic_pending_bmp' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'traffic_lastreported_bmp' not described in 'brcmf_fws_mac_descriptor'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-14-lee.jones@linaro.org
The function headers are either very weakly documented or not at all.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:94: warning: Function parameter or member 'reg50' not described in 'brcmf_btcoex_info'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:94: warning: Function parameter or member 'saved_regs_part2' not described in 'brcmf_btcoex_info'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:233: warning: Function parameter or member 'btci' not described in 'btcmf_btcoex_save_part1'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:253: warning: Function parameter or member 'btci' not described in 'brcmf_btcoex_restore_part1'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:273: warning: Function parameter or member 't' not described in 'brcmf_btcoex_timerfunc'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:453: warning: Function parameter or member 'vif' not described in 'brcmf_btcoex_set_mode'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:453: warning: Function parameter or member 'duration' not described in 'brcmf_btcoex_set_mode'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:453: warning: Excess function parameter 'cfg' description in 'brcmf_btcoex_set_mode'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-17-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
from drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:27:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_dotxstatus’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:845:6: warning: variable ‘mcl’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_b_phy_reset’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:1779:7: warning: variable ‘phy_in_reset’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_ucode_download’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:2273:23: warning: variable ‘wlc’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_b_coreinit’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:3176:6: warning: variable ‘sflags’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_set_chanspec’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:3902:7: warning: variable ‘switchband’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_down’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5182:7: warning: variable ‘dev_gone’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_ofdm_rateset_war’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5393:5: warning: variable ‘r’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘mac80211_wlc_set_nrate’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5876:6: warning: variable ‘bcmerror’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_d11hdrs_mac80211’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:6213:7: warning: variable ‘short_preamble’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-10-lee.jones@linaro.org
Some formatting issues, some missing and some extra descriptions.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:162: warning: Function parameter or member 'oui' not described in 'brcmf_p2p_pub_act_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:162: warning: Function parameter or member 'elts' not described in 'brcmf_p2p_pub_act_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:181: warning: Function parameter or member 'oui' not described in 'brcmf_p2p_action_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:181: warning: Function parameter or member 'elts' not described in 'brcmf_p2p_action_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:196: warning: Function parameter or member 'query_data' not described in 'brcmf_p2psd_gas_pub_act_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:210: warning: Function parameter or member 'extra_listen' not described in 'brcmf_config_af_params'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:776: warning: Function parameter or member 'ifp' not described in 'brcmf_p2p_run_escan'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:776: warning: Excess function parameter 'ndev' description in 'brcmf_p2p_run_escan'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:776: warning: Excess function parameter 'action' description in 'brcmf_p2p_run_escan'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:977: warning: Function parameter or member 'wdev' not described in 'brcmf_p2p_remain_on_channel'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:977: warning: Function parameter or member 'cookie' not described in 'brcmf_p2p_remain_on_channel'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:1063: warning: Function parameter or member 'channel' not described in 'brcmf_p2p_act_frm_search'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:1337: warning: Function parameter or member 'mac' not described in 'brcmf_p2p_gon_req_collision'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2046: warning: Function parameter or member 'cfg' not described in 'brcmf_p2p_ifchange'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2046: warning: Function parameter or member 'if_type' not described in 'brcmf_p2p_ifchange'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2046: warning: Excess function parameter 'mac' description in 'brcmf_p2p_ifchange'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-6-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
from drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:18:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_finalize’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:648:25: warning: variable ‘sgi’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_dotxstatus_complete’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:856:18: warning: variable ‘rr_retry_limit’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:855:5: warning: variable ‘antselid’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:853:41: warning: variable ‘tx_error’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:853:7: warning: variable ‘update_rate’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_dotxstatus’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:1037:28: warning: variable ‘tx_info’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:1035:28: warning: variable ‘ini’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-5-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/b43/phy_n.c: In function ‘b43_nphy_workarounds_rev3plus’:
drivers/net/wireless/broadcom/b43/phy_n.c:3346:3: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
drivers/net/wireless/broadcom/b43/phy_n.c: In function ‘b43_nphy_spur_workaround’:
drivers/net/wireless/broadcom/b43/phy_n.c:4608:4: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
drivers/net/wireless/broadcom/b43/phy_n.c:4641:4: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
drivers/net/wireless/broadcom/b43/phy_n.c: In function ‘b43_phy_initn’:
drivers/net/wireless/broadcom/b43/phy_n.c:6170:3: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
drivers/net/wireless/broadcom/b43/phy_n.c:6215:5: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "Alexander A. Klimov" <grandmaster@al2klimov.de>
Cc: Michael Buesch <m@bues.ch>
Cc: linux-wireless@vger.kernel.org
Cc: b43-dev@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-31-lee.jones@linaro.org
Also demote a commit block header which is clearly not suitable for kerneldoc.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c: In function ‘brcmf_fweh_handle_if_event’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:131:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:36: warning: Function parameter or member 'datalen' not described in 'brcmf_fweh_queue_item'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:44: warning: Function parameter or member 'code' not described in 'brcmf_fweh_event_name'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:44: warning: Function parameter or member 'name' not described in 'brcmf_fweh_event_name'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:127: warning: Function parameter or member 'emsg' not described in 'brcmf_fweh_handle_if_event'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:127: warning: Function parameter or member 'data' not described in 'brcmf_fweh_handle_if_event'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:127: warning: Excess function parameter 'item' description in 'brcmf_fweh_handle_if_event'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:127: warning: Excess function parameter 'ifpp' description in 'brcmf_fweh_handle_if_event'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:391: warning: Function parameter or member 'packet_len' not described in 'brcmf_fweh_process_event'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-24-lee.jones@linaro.org
The 4329 throughput drops from 40.2 Mbits/sec to 190 Kbits/sec in 2G
11n mode because the commit b41c232d33 ("brcmfmac: reserve 2 credits
for host tx control path"). To fix the issue, host driver only reserves
tx control credit when there is a txctl frame is pending to send. And
we also check available credit by using "not equal to 0" instead of
"greater than 0" because tx_max and tx_seq are circled positive numbers.
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Fixes: b41c232d33 ("brcmfmac: reserve 2 credits for host tx control path")
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200813070017.89023-1-wright.feng@cypress.com
Clang static analysis reports this error
brcmfmac/core.c:490:4: warning: Dereference of null pointer
(*ifp)->ndev->stats.rx_errors++;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In this block of code
if (ret || !(*ifp) || !(*ifp)->ndev) {
if (ret != -ENODATA && *ifp)
(*ifp)->ndev->stats.rx_errors++;
brcmu_pkt_buf_free_skb(skb);
return -ENODATA;
}
(*ifp)->ndev being NULL is caught as an error
But then it is used to report the error.
So add a check before using it.
Fixes: 91b632803e ("brcmfmac: Use net_device_stats from struct net_device")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802161804.6126-1-trix@redhat.com
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719111124.58167-1-grandmaster@al2klimov.de
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719110115.58085-1-grandmaster@al2klimov.de
