[ Upstream commit 52a2f0608366a629d43dacd3191039c95fef74ba ]
LED Select (LED_SEL) bit in the LED General Purpose IO Configuration
register is used to determine the functionality of external LED pins
(Speed Indicator, Link and Activity Indicator, Full Duplex Link
Indicator). The default value for this bit is 0 when no EEPROM is
present. If a EEPROM is present, the default value is the value of the
LED Select bit in the Configuration Flags of the EEPROM. A USB Reset or
Lite Reset (LRST) will cause this bit to be restored to the image value
last loaded from EEPROM, or to be set to 0 if no EEPROM is present.
While configuring the dual purpose GPIO/LED pins to LED outputs in the
LED General Purpose IO Configuration register, the LED_SEL bit is changed
as 0 and resulting the configured value from the EEPROM is cleared. The
issue is fixed by using read-modify-write approach.
Fixes: f293501c61 ("smsc95xx: configure LED outputs")
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Link: https://lore.kernel.org/r/20240523085314.167650-1-Parthiban.Veerasooran@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d50729f1d60bca822ef6d9c1a5fb28d486bd7593 ]
Some usb drivers try to set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize override.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c611723 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f7a ("net: usb: ax88179_178a:
stop lying about skb->truesize")
v3: also fix a sparse error ( https://lore.kernel.org/oe-kbuild-all/202405091310.KvncIecx-lkp@intel.com/ )
v2: leave the skb_trim() game because smsc95xx_rx_csum_offload()
needs the csum part. (Jakub)
While we are it, use get_unaligned() in smsc95xx_rx_csum_offload().
Fixes: 2f7ca802bd ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Cc: UNGLinuxDriver@microchip.com
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240509083313.2113832-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05417aa9c0c038da2464a0c504b9d4f99814a23b ]
Some usb drivers set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize override.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c611723 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f7a ("net: usb: ax88179_178a:
stop lying about skb->truesize")
Fixes: c9b37458e9 ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240506143939.3673865-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9aad6e45c4e7d16b2bb7c3794154b828fb4384b4 ]
Some usb drivers try to set small skb->truesize and break
core networking stacks.
I replace one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c611723 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f7a ("net: usb: ax88179_178a:
stop lying about skb->truesize")
Fixes: 361459cd96 ("net: usb: aqc111: Implement RX data path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240506135546.3641185-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1eecc7ab82c42133b748e1895275942a054a7f67 ]
Current driver has some asymmetry in the runtime PM calls. On lan78xx_open()
it will call usb_autopm_get() and unconditionally usb_autopm_put(). And
on lan78xx_stop() it will call only usb_autopm_put(). So far, it was
working only because this driver do not activate autosuspend by default,
so it was visible only by warning "Runtime PM usage count underflow!".
Since, with current driver, we can't use runtime PM with active link,
execute lan78xx_open()->usb_autopm_put() only in error case. Otherwise,
keep ref counting high as long as interface is open.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f4cc6e25148cc141f97afb41b4dfe9eb1cce613 ]
If the interface is given an IP address while the device is
suspended (as a result of an auto-suspend event) there is a race
between lan78xx_resume() and lan78xx_open() that can result in an
exception or failure to handle incoming packets. The following
changes fix this problem.
Introduce a mutex to serialise operations in the network interface
open and stop entry points with respect to the USB driver suspend
and resume entry points.
Move Tx and Rx data path start/stop to lan78xx_start() and
lan78xx_stop() respectively and flush the packet FIFOs before
starting the Tx and Rx data paths. This prevents the MAC and FIFOs
getting out of step and delivery of malformed packets to the network
stack.
Stop processing of received packets before disconnecting the
PHY from the MAC to prevent a kernel exception caused by handling
packets after the PHY device has been removed.
Refactor device auto-suspend code to make it consistent with the
the system suspend code and make the suspend handler easier to read.
Add new code to stop wake-on-lan packets or PHY events resuming the
host or device from suspend if the device has not been opened
(typically after an IP address is assigned).
This patch is dependent on changes to lan78xx_suspend() and
lan78xx_resume() introduced in the previous patch of this patch set.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 1eecc7ab82c4 ("net: lan78xx: fix runtime PM count underflow on link stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1210fe63bf8b080edd0805240e90b81b6b069c1 ]
The MAC can get out of step with the internal packet FIFOs if the
system goes to sleep when the link is active, especially at high
data rates. This can result in partial frames in the packet FIFOs
that in result in malformed frames being delivered to the host.
This occurs because the driver does not enable/disable the internal
packet FIFOs in step with the corresponding MAC data path. The
following changes fix this problem.
Update code that enables/disables the MAC receiver and transmitter
to the more general Rx and Tx data path, where the data path in each
direction consists of both the MAC function (Tx or Rx) and the
corresponding packet FIFO.
In the receive path the packet FIFO must be enabled before the MAC
receiver but disabled after the MAC receiver.
In the transmit path the opposite is true: the packet FIFO must be
enabled after the MAC transmitter but disabled before the MAC
transmitter.
The packet FIFOs can be flushed safely once the corresponding data
path is stopped.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 1eecc7ab82c4 ("net: lan78xx: fix runtime PM count underflow on link stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3415f6baaddb9b39d7112247ab39ef3c700f882e ]
There are many places in the driver where the return code from a
function call is captured but without a subsequent test of the
return code and appropriate action taken.
This patch adds the missing return code tests and action. In most
cases the action is an early exit from the calling function.
The function lan78xx_set_suspend() was also updated to make it
consistent with lan78xx_suspend().
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 1eecc7ab82c4 ("net: lan78xx: fix runtime PM count underflow on link stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ceec7d33adf9647293f24d2fd9a055b89c63864 ]
Fix white space and code style issues identified by checkpatch.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 1eecc7ab82c4 ("net: lan78xx: fix runtime PM count underflow on link stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c68b2c9eba38ec3f60f4894b189090febf4d8d22 ]
The MII code does not check the return value of mdio_read (among
others), and therefore no error code should be sent. A previous fix to
the use of an uninitialized variable propagates negative error codes,
that might lead to wrong operations by the MII library.
An example of such issues is the use of mii_nway_restart by the dm9601
driver. The mii_nway_restart function does not check the value returned
by mdio_read, which in this case might be a negative number which could
contain the exact bit the function checks (BMCR_ANENABLE = 0x1000).
Return zero in case of error, as it is common practice in users of
mdio_read to avoid wrong uses of the return value.
Fixes: 8f8abb863fa5 ("net: usb: dm9601: fix uninitialized variable use in dm9601_mdio_read")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20240225-dm9601_ret_err-v1-1-02c1d959ea59@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e67899abfbfdea0c3c0ed3fd263ffc601c5c157 ]
Same as LAN7800, LAN7850 can be used without EEPROM. If EEPROM is not
present or not flashed, LAN7850 will fail to sync the speed detected by the PHY
with the MAC. In case link speed is 100Mbit, it will accidentally work,
otherwise no data can be transferred.
Better way would be to implement link_up callback, or set auto speed
configuration unconditionally. But this changes would be more intrusive.
So, for now, set it only if no EEPROM is found.
Fixes: e69647a19c ("lan78xx: Set ASD in MAC_CR when EEE is enabled.")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240222123839.2816561-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaac6a2d26b65511e164772bec6918fcbc61938e ]
Add check for usbnet_get_endpoints() and return the error if it fails
in order to transfer the error.
Fixes: 16626b0cc3 ("asix: Add a new driver for the AX88172A")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccab434e674ca95d483788b1895a70c21b7f016a ]
If a device sends a packet that is inbetween 0
and sizeof(u64) the value passed to skb_trim()
as length will wrap around ending up as some very
large value.
The driver will then proceed to parse the header
located at that position, which will either oops or
process some random value.
The fix is to check against sizeof(u64) rather than
0, which the driver currently does. The issue exists
since the introduction of the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0739af07d1d947af27c877f797cb82ceee702515 ]
Using generic ASIX Electronics Corp. AX88179 Gigabit Ethernet device,
the following test cycle has been implemented:
- power on
- check logs
- shutdown
- after detecting the system shutdown, disconnect power
- after approximately 60 seconds of sleep, power is restored
Running some cycles, sometimes error logs like this appear:
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to write reg index 0x0001: -19
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to read reg index 0x0001: -19
...
These failed operation are happening during ax88179_reset execution, so
the initialization could not be correct.
In order to avoid this, we need to increase the delay after reset and
clock initial operations. By using these larger values, many cycles
have been run and no failed operations appear.
It would be better to check some status register to verify when the
operation has finished, but I do not have found any available information
(neither in the public datasheets nor in the manufacturer's driver). The
only available information for the necessary delays is the maufacturer's
driver (original values) but the proposed values are not enough for the
tested devices.
Fixes: e2ca90c276 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Reported-by: Herb Wei <weihao.bj@ieisystem.com>
Tested-by: Herb Wei <weihao.bj@ieisystem.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20231120120642.54334-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8d35024d4059ca550cba11ac9ab23a6c238d929 ]
The error handling in rtl8152_probe() is missing a call to release
firmware. Add it in to match what's in the cleanup code in
rtl8152_disconnect().
Fixes: 9370f2d05a ("r8152: support request_firmware for RTL8153")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb8adff9123e492598162ac1baad01a53891aef6 ]
The error handling in rtl8152_probe() is missing a call to cancel the
hw_phy_work. Add it in to match what's in the cleanup code in
rtl8152_disconnect().
Fixes: a028a9e003 ("r8152: move the settings of PHY to a work queue")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dd17689526971c5ae12bc8398f34bd68cd0499e ]
The rtl8152_probe() function lacks a call to the chip-specific
unload() routine when it sees an error in probe. Add it in to match
the cleanup code in rtl8152_disconnect().
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5feba71ec9c14a54c3babdc732c5b6866d8ee43 ]
According to the comment next to USB_CTRL_GET_TIMEOUT and
USB_CTRL_SET_TIMEOUT, although sending/receiving control messages is
usually quite fast, the spec allows them to take up to 5 seconds.
Let's increase the timeout in the Realtek driver from 500ms to 5000ms
(using the #defines) to account for this.
This is not just a theoretical change. The need for the longer timeout
was seen in testing. Specifically, if you drop a sc7180-trogdor based
Chromebook into the kdb debugger and then "go" again after sitting in
the debugger for a while, the next USB control message takes a long
time. Out of ~40 tests the slowest USB control message was 4.5
seconds.
While dropping into kdb is not exactly an end-user scenario, the above
is similar to what could happen due to an temporary interrupt storm,
what could happen if there was a host controller (HW or SW) issue, or
what could happen if the Realtek device got into a confused state and
needed time to recover.
This change is fairly critical since the r8152 driver in Linux doesn't
expect register reads/writes (which are backed by USB control
messages) to fail.
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Suggested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7b8d60b37237680009dd0b025fe8c067aba0ee3 ]
According to the document of napi, there is no rx process when the
budget is 0. Therefore, r8152_poll() has to return 0 directly when the
budget is equal to 0.
Fixes: d2187f8e44 ("r8152: divide the tx and rx bottom functions")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7e01c7f7046efc2c7c192c3619db43292b98e997 upstream.
Currently in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is lower than
the calculated "min" value, but greater than zero, the logic sets
tx_max to dwNtbOutMaxSize. This is then used to allocate a new SKB in
cdc_ncm_fill_tx_frame() where all the data is handled.
For small values of dwNtbOutMaxSize the memory allocated during
alloc_skb(dwNtbOutMaxSize, GFP_ATOMIC) will have the same size, due to
how size is aligned at alloc time:
size = SKB_DATA_ALIGN(size);
size += SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
Thus we hit the same bug that we tried to squash with
commit 2be6d4d16a084 ("net: cdc_ncm: Allow for dwNtbOutMaxSize to be unset or zero")
Low values of dwNtbOutMaxSize do not cause an issue presently because at
alloc_skb() time more memory (512b) is allocated than required for the
SKB headers alone (320b), leaving some space (512b - 320b = 192b)
for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
skbuff: skb_over_panic: text:ffffffff831f755b len:184 put:172 head:ffff88811f1c6c00 data:ffff88811f1c6c00 tail:0xb8 end:0x80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:113!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 57 Comm: kworker/0:2 Not tainted 5.15.106-syzkaller-00249-g19c0ed55a470 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/14/2023
Workqueue: mld mld_ifc_work
RIP: 0010:skb_panic net/core/skbuff.c:113 [inline]
RIP: 0010:skb_over_panic+0x14c/0x150 net/core/skbuff.c:118
[snip]
Call Trace:
<TASK>
skb_put+0x151/0x210 net/core/skbuff.c:2047
skb_put_zero include/linux/skbuff.h:2422 [inline]
cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1131 [inline]
cdc_ncm_fill_tx_frame+0x11ab/0x3da0 drivers/net/usb/cdc_ncm.c:1308
cdc_ncm_tx_fixup+0xa3/0x100
Deal with too low values of dwNtbOutMaxSize, clamp it in the range
[USB_CDC_NCM_NTB_MIN_OUT_SIZE, CDC_NCM_NTB_MAX_SIZE_TX]. We ensure
enough data space is allocated to handle CDC data by making sure
dwNtbOutMaxSize is not smaller than USB_CDC_NCM_NTB_MIN_OUT_SIZE.
Fixes: 289507d336 ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning")
Cc: stable@vger.kernel.org
Reported-by: syzbot+9f575a1f15fc0c01ed69@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=b982f1059506db48409d
Link: https://lore.kernel.org/all/20211202143437.1411410-1-lee.jones@linaro.org/
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230517133808.1873695-2-tudor.ambarus@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 43ffe6caccc7a1bb9d7442fbab521efbf6c1378c ]
Packet length check needs to be located after size and align_count
calculation to prevent kernel panic in skb_pull() in case
rx_cmd_a & RX_CMD_A_RED evaluates to true.
Fixes: d8b228318935 ("net: usb: smsc75xx: Limit packet length to skb->len")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20230316110540.77531-1-szymon.heidrich@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8b228318935044dafe3a5bc07ee71a1f1424b8d ]
Packet length retrieved from skb data may be larger than
the actual socket buffer length (up to 9026 bytes). In such
case the cloned skb passed up the network stack will leak
kernel memory contents.
Fixes: d0cad87170 ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e57cf3639c323eeed05d3725fd82f91b349adca8 ]
Move the LAN7800 internal phy (phy ID 0x0007c132) specific register
accesses to the phy driver (microchip.c).
Fix the error reported by Enguerrand de Ribaucourt in December 2022,
"Some operations during the cable switch workaround modify the register
LAN88XX_INT_MASK of the PHY. However, this register is specific to the
LAN8835 PHY. For instance, if a DP8322I PHY is connected to the LAN7801,
that register (0x19), corresponds to the LED and MAC address
configuration, resulting in unapropriate behavior."
I did not test with the DP8322I PHY, but I tested with an EVB-LAN7800
with the internal PHY.
Fixes: 14437e3fa2 ("lan78xx: workaround of forced 100 Full/Half duplex mode error")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230301154307.30438-1-yuiko.oshino@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06cd7c46b3ab3f2252c61bf85b191236cf0254e1 ]
Fixes the following W=1 kernel build warning(s):
drivers/net/usb/lan78xx.c: In function ‘lan78xx_read_raw_otp’:
drivers/net/usb/lan78xx.c:825:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_write_raw_otp’:
drivers/net/usb/lan78xx.c:879:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_deferred_multicast_write’:
drivers/net/usb/lan78xx.c:1041:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_update_flowcontrol’:
drivers/net/usb/lan78xx.c:1127:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_init_mac_address’:
drivers/net/usb/lan78xx.c:1666:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_link_status_change’:
drivers/net/usb/lan78xx.c:1841:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_irq_bus_sync_unlock’:
drivers/net/usb/lan78xx.c:1920:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan8835_fixup’:
drivers/net/usb/lan78xx.c:1994:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_rx_max_frame_length’:
drivers/net/usb/lan78xx.c:2192:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_change_mtu’:
drivers/net/usb/lan78xx.c:2270:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_mac_addr’:
drivers/net/usb/lan78xx.c:2299:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_features’:
drivers/net/usb/lan78xx.c:2333:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_suspend’:
drivers/net/usb/lan78xx.c:3807:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-25-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: e57cf3639c32 ("net: lan78xx: fix accessing the LAN7800's internal phy specific registers from the MAC driver")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c68f345b7c425b38656e1791a0486769a8797016 upstream.
syzbot reported that act_len in kalmia_send_init_packet() is
uninitialized when passing it to the first usb_bulk_msg error path. Jiri
Pirko noted that it's pointless to pass it in the error path, and that
the value that would be printed in the second error path would be the
value of act_len from the first call to usb_bulk_msg.[1]
With this in mind, let's just not pass act_len to the usb_bulk_msg error
paths.
1: https://lore.kernel.org/lkml/Y9pY61y1nwTuzMOa@nanopsycho/
Fixes: d40261236e ("net/usb: Add Samsung Kalmia driver for Samsung GT-B3730")
Reported-and-tested-by: syzbot+cd80c5ef5121bfe85b55@syzkaller.appspotmail.com
Signed-off-by: Miko Larsson <mikoxyzzz@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ecf7cf8efb59789e2b21d2f9ab926142579092b2 ]
Packet len computed as difference of length word extracted from
skb data and four may result in a negative value. In such case
processing of the buffer should be interrupted rather than
setting sr_skb->len to an unexpectedly large value (due to cast
from signed to unsigned integer) and passing sr_skb to
usbnet_skb_return.
Fixes: e9da0b56fe27 ("sr9700: sanity check for packet length")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20230114182326.30479-1-szymon.heidrich@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7dd13805f8b8fc1ce3b6d40f6aff47e66b72ad2 ]
Variables off and len typed as uint32 in rndis_query function
are controlled by incoming RNDIS response message thus their
value may be manipulated. Setting off to a unexpectetly large
value will cause the sum with len and 8 to overflow and pass
the implemented validation step. Consequently the response
pointer will be referring to a location past the expected
buffer boundaries allowing information leakage e.g. via
RNDIS_OID_802_3_PERMANENT_ADDRESS OID.
Fixes: ddda086240 ("USB: rndis_host, various cleanups")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a487069e11b6527373f7c6f435d8998051d0b5d9 ]
Add RmNet support for LARA-L6.
LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface
In RmNet mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b960c967f2aa01ab8f45c5a0bd78e754cffdeee ]
Commit 05b35e7eb9 ("smsc95xx: add phylib support") amended
smsc95xx_resume() to call phy_init_hw(). That function waits for the
device to runtime resume even though it is placed in the runtime resume
path, causing a deadlock.
The problem is that phy_init_hw() calls down to smsc95xx_mdiobus_read(),
which never uses the _nopm variant of usbnet_read_cmd().
Commit b4df480f68 ("usbnet: smsc95xx: add reset_resume function with
reset operation") causes a similar deadlock on resume if the device was
already runtime suspended when entering system sleep:
That's because the commit introduced smsc95xx_reset_resume(), which
calls down to smsc95xx_reset(), which neglects to use _nopm accessors.
Fix by auto-detecting whether a device access is performed by the
suspend/resume task_struct and use the _nopm variant if so. This works
because the PM core guarantees that suspend/resume callbacks are run in
task context.
Stacktrace for posterity:
INFO: task kworker/2:1:49 blocked for more than 122 seconds.
Workqueue: usb_hub_wq hub_event
schedule
rpm_resume
__pm_runtime_resume
usb_autopm_get_interface
usbnet_read_cmd
__smsc95xx_read_reg
__smsc95xx_phy_wait_not_busy
__smsc95xx_mdio_read
smsc95xx_mdiobus_read
__mdiobus_read
mdiobus_read
smsc_phy_reset
phy_init_hw
smsc95xx_resume
usb_resume_interface
usb_resume_both
usb_runtime_resume
__rpm_callback
rpm_callback
rpm_resume
__pm_runtime_resume
usb_autoresume_device
hub_event
process_one_work
Fixes: b4df480f68 ("usbnet: smsc95xx: add reset_resume function with reset operation")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.16+
Cc: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1bd3a383075c64d638e65d263c9267b08ee7733c upstream.
The Lenovo OneLink+ Dock contains an RTL8153 controller that behaves as
a broken CDC device by default. Add the custom Lenovo PID to the r8152
driver to support it properly.
Also, systems compatible with this dock provide a BIOS option to enable
MAC address passthrough (as per Lenovo document "ThinkPad Docking
Solutions 2017"). Add the custom PID to the MAC passthrough list too.
Tested on a ThinkPad 13 1st gen with the expected results:
passthrough disabled: Invalid header when reading pass-thru MAC addr
passthrough enabled: Using pass-thru MAC addr XX:XX:XX:XX:XX:XX
Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
