[ Upstream commit 96a7e861d9e04d07febd3011c30cd84cd141d81f ]
After calling ethtool -g it was not possible to adjust the TX ring
size again:
# ethtool -g eth1
Ring parameters for eth1:
Pre-set maximums:
RX: 4
RX Mini: n/a
RX Jumbo: n/a
TX: 10
Current hardware settings:
RX: 4
RX Mini: n/a
RX Jumbo: n/a
TX: 10
# ethtool -G eth1 tx 8
netlink error: Invalid argument
The reason for this is that the readonly setting rx_pending get
initialized and after that the range check in qcaspi_set_ringparam()
fails regardless of the provided parameter. So fix this by accepting
the exposed RX defaults. Instead of adding another magic number
better use a new define here.
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20231206141222.52029-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4e6064c97c050bd9904925ff7d53d0c9954fc7b ]
The qca_spi driver stop and restart the SPI kernel thread
(via ndo_stop & ndo_open) in case of TX ring changes. This is
a big issue because it allows userspace to prevent restart of
the SPI kernel thread (via signals). A subsequent change of
TX ring wrongly assume a valid spi_thread pointer which result
in a crash.
So prevent this by stopping the network traffic handling and
temporary park the SPI thread.
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20231206141222.52029-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Interferences on the SPI line could distort the response of
available buffer space. So at least we should check that the
response doesn't exceed the maximum available buffer space.
In error case increase a new error counter and retry it later.
This behavior avoids buffer errors in the QCA7000, which
results in an unnecessary chip reset including packet loss.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SPI protocol for the QCA7000 doesn't have any fault detection.
In order to increase the drivers reliability in noisy environments,
we could implement a write verification inspired by the enc28j60.
This should avoid situations were the driver wrongly assumes the
receive interrupt is enabled and miss all incoming packets.
This function is disabled per default and can be controlled via module
parameter wr_verify.
Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to export qcaspi_netdev_open and qcaspi_netdev_close
because they are also accessible via the net_device_ops.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Ethernet over SPI driver for the
Qualcomm QCA7000 HomePlug GreenPHY.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
