The lifetime of the Rx listener item ('rxl_item') is managed using RCU,
but is dereferenced outside of RCU read-side critical section, which can
lead to a use-after-free.
Fix this by increasing the scope of the RCU read-side critical section.
Fixes: 93c1edb27f ("mlxsw: Introduce Mellanox switch driver core")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cited commit mistakenly removed the trap group for externally routed
packets (e.g., via the management interface) and grouped locally routed
and externally routed packet traps under the same group, thereby
subjecting them to the same policer.
This can result in problems, for example, when FRR is restarted and
suddenly all transient traffic is trapped to the CPU because of a
default route through the management interface. Locally routed packets
required to re-establish a BGP connection will never reach the CPU and
the routing tables will not be re-populated.
Fix this by using a different trap group for externally routed packets.
Fixes: 8110668ecd ("mlxsw: spectrum_trap: Register layer 3 control traps")
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cited commit added the ability to program link-local prefix routes to
the ASIC so that relevant packets are routed and trapped correctly.
However, host routes were not included in the change and thus not
programmed to the ASIC. This can result in packets being trapped via an
external route trap instead of a local route trap as in IPv4.
Fix this by programming all the link-local routes to the ASIC.
Fixes: 10d3757fcb ("mlxsw: spectrum_router: Allow programming link-local prefix routes")
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on PAGE_SIZE, the following unused parameter warning can be
reported:
drivers/net/ethernet/intel/ice/ice_txrx.c: In function ‘ice_rx_frame_truesize’:
drivers/net/ethernet/intel/ice/ice_txrx.c:513:21: warning: unused parameter ‘size’ [-Wunused-parameter]
unsigned int size)
The 'size' variable is used only when PAGE_SIZE >= 8192. Add __maybe_unused
to remove the warning.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
For the FW logging info AQ command, we currently set the ICE_AQ_FLAG_RD
in order to work around a FW issue. This issue has been fixed so remove the
workaround.
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the PF VSI's context parameters are left in a bad state when
going into safe mode. This is causing VLAN traffic to not pass. Fix this
by configuring the PF VSI to allow all VLAN tagged traffic.
Also, remove redundant comment explaining the safe mode flow in
ice_probe().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This is a port of i40e commit 705639572e ("i40e: need_wakeup flag might
not be set for Tx").
Quoting the original commit message:
"The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an interrupt
since interrupts are disabled in the napi poll loop) between the time we
stopped processing the Tx completions and interrupts are enabled again.
In this case, the need_wakeup flag will have been cleared at the end of
the Tx completion processing as we believe we will get an interrupt from
the outstanding completion at a later point in time. But if this
completion interrupt occurs before interrupts are enable, we lose it and
should at that point really have set the need_wakeup flag since there
are no more outstanding completions that can generate an interrupt to
continue the processing. When this happens, user space will see a Tx
queue need_wakeup of 0 and skip issuing a syscall, which means will
never get into the Tx processing again and we have a deadlock."
As a result, packet processing stops. This patch introduces a fix for
this issue, by always setting the need_wakeup flag at the end of an
interrupt processing. This ensures that the deadlock will not happen.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Distribute the Tx queues evenly across all queue groups. This will
help the queues to get more equal sharing among the queues when all
are in use.
In the previous algorithm, the next queue group node will be picked up
only after the previous one filled with max children.
For example: if VSI is configured with 9 queues, the first 8 queues
will be assigned to queue group 1 and the 9th queue will be assigned to
queue group 2.
The 2 queue groups split the bandwidth between them equally (50:50).
The first queue group node will share the 50% bandwidth with all of
its children (8 queues). And the second queue group node will share
the entire 50% bandwidth with its only children.
The new algorithm will fix this issue.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
By default the queues are configured in legacy mode. The default
BW settings for legacy/advanced modes are different. The existing
code was using the advanced mode default value of 1 which was
incorrect. This caused the unbalanced BW sharing among siblings.
The recommended default value is applied.
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If a user sets the value of the TX or RX descriptors to some non-default
value using 'ethtool -G' then we need to not overwrite the values when
we rebuild the VSI. The VSI rebuild could happen as a result of a user
setting the number of queues via the 'ethtool -L' command. Fix this by
checking to see if the value we have stored is non-zero and if it is
then don't change the value.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Return ICE_ERR_DOES_NOT_EXIST return code if admin command error code is
ICE_AQ_RC_ENOENT (not exist). ice_aq_sw_rules is used when switch
rule is getting added/deleted/updated. In case of delete/update
switch rule, admin command can return ICE_AQ_RC_ENOENT error code
if such rule does not exist, hence return ICE_ERR_DOES_NOT_EXIST error
code from ice_aq_sw_rule, so that caller of this function can decide
how to handle ICE_ERR_DOES_NOT_EXIST.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
During a PCI FLR the MSI-X Enable flag in the VF PCI MSI-X capability
register will be cleared. This can lead to issues when a VF is
assigned to a VM because in these cases the VF driver receives no
indication of the PF PCI error/reset and additionally it is incapable
of restoring the cleared flag in the hypervisor configuration space
without fully reinitializing the driver interrupt functionality.
Since the VF driver is unable to easily resolve this condition on its own,
restore the VF MSI-X flag during the PF PCI reset handling.
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the driver experiences a link event (especially link up)
there can be multiple events generated. Some of these are
link fault and still have a state of DOWN set. The problem
happens when the link comes UP during the PF driver handling
one of the LINK DOWN events. The status of the link is updated
and is now seen as UP, so when the actual LINK UP event comes,
the port information has already been updated to be seen as UP,
even though none of the UP activities have been completed.
After the link information has been updated in the link
handler and evaluated for MEDIA PRESENT, if the state
of the link has been changed to UP, treat the DOWN event
as an UP event since the link is now UP.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After a GLOBR, the link was broken so that a link
up situation was being seen as a link down.
The problem was that the rebuild process was updating
the port_info link status without doing any of the
other things that need to be done when link changes.
This was causing the port_info struct to have current
"UP" information so that any further UP interrupts
were skipped as redundant.
The rebuild flow should *not* be updating the port_info
struct link information, so eliminate this and leave
it to the link event handling code.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a bug where the LFC settings are not being preserved
through a link event. The registers in question are the ones
that are touched (and restored) when a set_local_mib AQ command
is performed.
On a link-up event, make sure that a set_local_mib is being
performed.
Move the function ice_aq_set_lldp_mib() from the DCB specific
ice_dcb.c to ice_common.c so that the driver always has access
to this AQ command.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When WoL is enabled and the machine is powered off, the PHY remains
waiting for wakeup events at max speed, which is a waste of energy.
Slow down the PHY speed before stopping the ethernet if WoL is enabled,
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the stmmac driver WOL implementation relies on MAC's PMT
feature. We have a case: the MAC HW doesn't enable PMT, instead, we
rely on the phy to support WOL. Implement the support for this case.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to prepare WOL support with phy. Compared with WOL
implementation which relies on the MAC's PMT features, in phy
supported WOL case, device_may_wakeup() may also be true, but we
should not call mac's pmt() function if HW doesn't enable PMT.
And during resume, we should call phylink_start() if PMT is disabled.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If !device_can_wakeup(), there's no need to futher check. And return
-EOPNOTSUPP rather than -EINVAL if !device_can_wakeup().
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove WAKE_MAGIC from supported modes if the HW capability register
shows no support for pmt_magic_frame.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
improve the error message when functions return failure and dump
relevant registers in some exception handling processes
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add support to handle hw abnormal event such as hardware failure,
cable unplugged,link error
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added unregister_netdev in the driver remove
function. Generally unregister_netdev is called
after disabling all the device interrupts but here
it is called before disabling device mailbox
interrupts. The reason behind this is VF needs
mailbox interrupt to communicate with its PF to
clean up its resources during otx2_stop.
otx2_stop disables packet I/O and queue interrupts
first and by using mailbox interrupt communicates
to PF to free VF resources. Hence this patch
calls unregister_device just before
disabling mailbox interrupts.
Fixes: 3184fb5ba9 ("octeontx2-vf: Virtual function driver support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During driver exit cancel the queued
reset_task work in VF driver.
Fixes: 3184fb5ba9 ("octeontx2-vf: Virtual function driver support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two bugs exist in the code related to reset_task
in PF driver one is the missing protection
against network stack ndo_open and ndo_close.
Other one is the missing cancel_work.
This patch fixes those problems.
Fixes: 4ff7d1488a ("octeontx2-pf: Error handling support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the newly added pldmfw library to implement device flash update for
the Intel ice networking device driver. This support uses the devlink
flash update interface.
The main parts of the flash include the Option ROM, the netlist module,
and the main NVM data. The PLDM firmware file contains modules for each
of these components.
Using the pldmfw library, the provided firmware file will be scanned for
the three major components, "fw.undi" for the Option ROM, "fw.mgmt" for
the main NVM module containing the primary device firmware, and
"fw.netlist" containing the netlist module.
The flash is separated into two banks, the active bank containing the
running firmware, and the inactive bank which we use for update. Each
module is updated in a staged process. First, the inactive bank is
erased, preparing the device for update. Second, the contents of the
component are copied to the inactive portion of the flash. After all
components are updated, the driver signals the device to switch the
active bank during the next EMP reset (which would usually occur during
the next reboot).
Although the firmware AdminQ interface does report an immediate status
for each command, the NVM erase and NVM write commands receive status
asynchronously. The driver must not continue writing until previous
erase and write commands have finished. The real status of the NVM
commands is returned over the receive AdminQ. Implement a simple
interface that uses a wait queue so that the main update thread can
sleep until the completion status is reported by firmware. For erasing
the inactive banks, this can take quite a while in practice.
To help visualize the process to the devlink application and other
applications based on the devlink netlink interface, status is reported
via the devlink_flash_update_status_notify. While we do report status
after each 4k block when writing, there is no real status we can report
during erasing. We simply must wait for the complete module erasure to
finish.
With this implementation, basic flash update for the ice hardware is
supported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a flash update, the pending status of the update can be determined
from the device capabilities.
Read the appropriate device capability and store whether there is
a pending update awaiting a reboot.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add structures, identifiers, and helper functions for several AdminQ
commands related to performing a firmware update for the ice hardware.
These will be used in future code for implementing the devlink
.flash_update handler.
Signed-off-by: Cudzilo, Szymon T <szymon.t.cudzilo@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends function parsing response from Discover Device
Capability AQC to check if the device supports unified NVM update flow.
Signed-off-by: Jacek Naczyk <jacek.naczyk@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5 fixes-2020-07-28
This series introduces some fixes to mlx5 driver.
v1->v2:
- Drop the "Hold reference on mirred devices" patch, until Or's
comments are addressed.
- Imporve "Modify uplink state" patch commit message per Or's request.
Please pull and let me know if there is any problem.
For -Stable:
For -stable v4.9
('net/mlx5e: Fix error path of device attach')
For -stable v4.15
('net/mlx5: Verify Hardware supports requested ptp function on a given
pin')
For -stable v5.3
('net/mlx5e: Modify uplink state on interface up/down')
For -stable v5.4
('net/mlx5e: Fix kernel crash when setting vf VLANID on a VF dev')
('net/mlx5: E-switch, Destroy TSAR when fail to enable the mode')
For -stable v5.5
('net/mlx5: E-switch, Destroy TSAR after reload interface')
For -stable v5.7
('net/mlx5: Fix a bug of using ptp channel index as pin index')
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow QSFP-DD transceivers temperature thresholds reading for hardware
monitoring and thermal control.
For this type, the thresholds are located in page 02h according to the
"Module and Lane Thresholds" description from Common Management
Interface Specification.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Quad Small Form Factor Pluggable Double Density (QSFP-DD) hardware
specification defines a form factor that supports up to 400 Gbps in
aggregate over an 8x50-Gbps electrical interface. The QSFP-DD supports
both optical and copper interfaces.
Implementation is based on Common Management Interface Specification;
Rev 4.0 May 8, 2019. Table 8-2 "Identifier and Status Summary (Lower
Page)" from this spec defines "Id and Status" fields located at offsets
00h - 02h. Bit 2 at offset 02h ("Flat_mem") specifies QSFP EEPROM memory
mode, which could be "upper memory flat" or "paged". Flat memory mode is
coded "1", and indicates that only page 00h is implemented in EEPROM.
Paged memory is coded "0" and indicates that pages 00h, 01h, 02h, 10h
and 11h are implemented. Pages 10h and 11h are currently not supported
by the driver.
"Flat" memory mode is used for the passive copper transceivers. For this
type only page 00h (256 bytes) is available. "Paged" memory is used for
the optical transceivers. For this type pages 00h (256 bytes), 01h (128
bytes) and 02h (128 bytes) are available. Upper page 01h contains static
advertising field, while upper page 02h contains the module-defined
thresholds and lane-specific monitors.
Extend enumerator 'mlxsw_reg_mcia_eeprom_module_info_id' with additional
field 'MLXSW_REG_MCIA_EEPROM_MODULE_INFO_TYPE_ID'. This field is used to
indicate for QSFP-DD transceiver type which memory mode is to be used.
Expose 256 bytes buffer for QSFP-DD passive copper transceiver and
512 bytes buffer for optical.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting the PF interface up/down, notify the firmware to update
uplink state via MODIFY_VPORT_STATE, when E-Switch is enabled.
This behavior will prevent sending traffic out on uplink port when PF is
down, such as sending traffic from a VF interface which is still up.
Currently when calling mlx5e_open/close(), the driver only sends PAOS
command to notify the firmware to set the physical port state to
up/down, however, it is not sufficient. When VF is in "auto" state, it
follows the uplink state, which was not updated on mlx5e_open/close()
before this patch.
When switchdev mode is enabled and uplink representor is first enabled,
set the uplink port state value back to its FW default "AUTO".
Fixes: 63bfd399de ("net/mlx5e: Send PAOS command on interface up/down")
Signed-off-by: Ron Diskin <rondi@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In a special configuration, a ConnectX6-Dx pin pps-out might be activated
when driver is loaded. Fix the driver to always read the operational pin
mode when registering it, and advertise it accordingly.
Fixes: ee7f12205a ("net/mlx5e: Implement 1PPS support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5e_rep_is_lag_netdev is used as first check as part of netdev events
handler for bond device of non-uplink representors, this handler can get
any netdevice under the same network namespace of mlx5e netdevice. Current
code treats the netdev as mlx5e netdev and only later on verifies this,
hence causes the following Kasan trace:
[15402.744990] ==================================================================
[15402.746942] BUG: KASAN: slab-out-of-bounds in mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core]
[15402.749009] Read of size 8 at addr ffff880391f3f6b0 by task ovs-vswitchd/5347
[15402.752065] CPU: 7 PID: 5347 Comm: ovs-vswitchd Kdump: loaded Tainted: G B O --------- -t - 4.18.0-g3dcc204d291d-dirty #1
[15402.755349] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
[15402.757600] Call Trace:
[15402.758968] dump_stack+0x71/0xab
[15402.760427] print_address_description+0x6a/0x270
[15402.761969] kasan_report+0x179/0x2d0
[15402.763445] ? mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core]
[15402.765121] mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core]
[15402.766782] mlx5e_rep_esw_bond_netevent+0x129/0x620 [mlx5_core]
Fix by deferring the violating access to be post the netdev verify check.
Fixes: 7e51891a23 ("net/mlx5e: Use netdev events to set/del egress acl forward-to-vport rule")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix a bug where driver did not verify Hardware pin capabilities for
PTP functions.
Fixes: ee7f12205a ("net/mlx5e: Implement 1PPS support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On PTP mlx5_ptp_enable(on=0) flow, driver mistakenly used channel index
as pin index.
After ptp patch marked in fixes tag was introduced, driver can freely
call ptp_find_pin() as part of the .enable() callback.
Fix driver mlx5_ptp_enable(on=0) flow to always use ptp_find_pin(). With
that, Driver will use the correct pin index in mlx5_ptp_enable(on=0) flow.
In addition, when initializing the pins, always set channel to zero. As
all pins can be attached to all channels, let ptp_set_pinfunc() to move
them between the channels.
For stable branches, this fix to be applied only on kernels that includes
both patches in fixes tag. Otherwise, mlx5_ptp_enable(on=0) will be stuck
on pincfg_mux.
Fixes: 62582a7ee7 ("ptp: Avoid deadlocks in the programmable pin code.")
Fixes: ee7f12205a ("net/mlx5e: Implement 1PPS support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The cited commit add initialization of ethtool steering during
representor rx initializations without cleaning it up in representor
rx cleanup, this may cause for stale ethtool flows to remain after
moving back from switchdev mode to legacy mode.
Fixed by calling ethtool steering cleanup during rep rx cleanup.
Fixes: 6783e8b29f ("net/mlx5e: Init ethtool steering for representors")
Signed-off-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On failure to attach the netdev, fix the rollback by re-setting the
device's state back to MLX5E_STATE_DESTROYING.
Failing to attach doesn't stop statistics polling via .ndo_get_stats64.
In this case, although the device is not attached, it falsely continues
to query the firmware for counters. Setting the device's state back to
MLX5E_STATE_DESTROYING prevents the firmware counters query.
Fixes: 26e59d8077 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The steering tree is as follow (nic RX as example):
---------
|root_ns|
---------
|
--------------------------------
| | |
---------- ---------- ---------
|p(prio)0| | p1 | | pn |
---------- ---------- ---------
| |
---------------- ---------------
|ns(e.g bypass)| |ns(e.g. lag) |
---------------- ---------------
| | |
---- ---- ----
|p0| |p1| |pn|
---- ---- ----
|
----
|FT|
----
find_next_chained_ft(prio) returns the first flow table in the next
priority. If prio is a parent of a flow table then it returns the first
flow table in the next priority in the same namespace, else if prio
is parent of namespace, then it should return the first flow table
in the next namespace. Currently if the user requests to forward to
next namespace, the code calls to find_next_chained_ft with the prio
of the next namespace and not the prio of the namesapce itself.
Fixes: 9254f8ed15 ("net/mlx5: Add support in forward to namespace")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When eswitch offloads is enabled, TSAR is created before reloading
the interfaces.
However when eswitch offloads mode is disabled, TSAR is disabled before
reloading the interfaces.
To keep the eswitch enable/disable sequence as mirror, destroy TSAR
after reloading the interfaces.
Fixes: 1bd27b11c1 ("net/mlx5: Introduce E-switch QoS management")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
