The ti-sn65dsi86 MIPI DSI to eDP bridge chip has 4 pins on it that can
be used as GPIOs in a system. Each pin can be configured as input,
output, or a special function for the bridge chip. These are:
- GPIO1: SUSPEND Input
- GPIO2: DSIA VSYNC
- GPIO3: DSIA HSYNC or VSYNC
- GPIO4: PWM
Let's expose these pins as GPIOs. A few notes:
- Access to ti-sn65dsi86 is via i2c so we set "can_sleep".
- These pins can't be configured for IRQ.
- There are no programmable pulls or other fancy features.
- Keeping the bridge chip powered might be expensive. The driver is
setup such that if all used GPIOs are only inputs we'll power the
bridge chip on just long enough to read the GPIO and then power it
off again. Setting a GPIO as output will keep the bridge powered.
- If someone releases a GPIO we'll implicitly switch it to an input so
we no longer need to keep the bridge powered for it.
Because of all of the above limitations we just need to implement a
bare-bones GPIO driver. The device tree bindings already account for
this device being a GPIO controller so we only need the driver changes
for it.
NOTE: Despite the fact that these pins are nominally muxable I don't
believe it makes sense to expose them through the pinctrl interface as
well as the GPIO interface. The special functions are things that the
bridge chip driver itself would care about and it can just configure
the pins as needed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[added pdata->gchip.base = -1;]
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200507143354.v5.1.Ia50267a5549392af8b37e67092ca653a59c95886@changeid
This is a driver for video encoder with VGA and DVI/HDMI outputs.
There is no documentation for the chip -- the operation was guessed from
what was sniffed on a Dell Wyse 3020 ThinOS terminal, the register names
come from the ch7035 driver in Mediatek's GPL code dump.
Only bare minimum is implemented -- no fancy stuff, such as scaling. That
would only worsen our misery. We don't load the firmware and we don't need
to even bother enabling the MCU. There are probably no distributable
firmware images anyway.
Tested with a handful of monitors ranging from 1024x768@75 to 1400x1050@60,
with VGA as well as DVI.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200424213539.93157-4-lkundrak@v3.sk
Some older versions of gcc badly optimize code that passes
an inline function argument into another function by reference,
causing huge stack usage:
drivers/gpu/drm/bridge/tc358768.c: In function 'tc358768_bridge_pre_enable':
drivers/gpu/drm/bridge/tc358768.c:840:1: error: the frame size of 2256 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
Use a temporary variable as a workaround and add a comment pointing
to the gcc bug.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428215408.4111675-1-arnd@arndb.de
Analogix_dp driver acquires all its resources in the ->bind() callback,
what is a bit against the component driver based approach, where the
driver initialization is split into a probe(), where all resources are
gathered, and a bind(), where all objects are created and a compound
driver is initialized.
Extract all the resource related operations to analogix_dp_probe() and
analogix_dp_remove(), then call them before/after registration of the
device components from the main Exynos DP and Rockchip DP drivers. Also
move the plat_data initialization to the probe() to make it available for
the analogix_dp_probe() function.
This fixes the multiple calls to the bind() of the DRM compound driver
when the DP PHY driver is not yet loaded/probed:
[drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations
exynos-drm exynos-drm: bound 14400000.fimd (ops fimd_component_ops [exynosdrm])
exynos-drm exynos-drm: bound 14450000.mixer (ops mixer_component_ops [exynosdrm])
exynos-dp 145b0000.dp-controller: no DP phy configured
exynos-drm exynos-drm: failed to bind 145b0000.dp-controller (ops exynos_dp_ops [exynosdrm]): -517
exynos-drm exynos-drm: master bind failed: -517
...
[drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations
exynos-drm exynos-drm: bound 14400000.fimd (ops hdmi_enable [exynosdrm])
exynos-drm exynos-drm: bound 14450000.mixer (ops hdmi_enable [exynosdrm])
exynos-drm exynos-drm: bound 145b0000.dp-controller (ops hdmi_enable [exynosdrm])
exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_enable [exynosdrm])
[drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
Console: switching to colour frame buffer device 170x48
exynos-drm exynos-drm: fb0: exynosdrmfb frame buffer device
[drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1
...
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310103427.26048-1-m.szyprowski@samsung.com
(cherry picked from commit 83a196773b)
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
is_color_space_conversion() is a misnomer. It checks not only if color
space conversion is needed, but also if format conversion is needed.
This is actually desired behaviour because result of this function
determines if CSC block should be enabled or not (CSC block can also do
format conversion).
In order to clear misunderstandings, let's rework
is_color_space_conversion() to do exactly what is supposed to do and add
another function which will determine if CSC block must be enabled or
not.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304232512.51616-5-jernej.skrabec@siol.net
drm_fb_helper_{add,remove}_one_connector() and
drm_fb_helper_single_add_all_connectors() are dummy functions now
and serve no purpose. Hence remove their calls.
This is the preparatory step for removing the
drm_fb_helper_{add,remove}_one_connector() functions from
drm_fb_helper.h
This removal is done using below sementic patch and unused variable
compilation warnings are fixed manually.
@@
@@
- drm_fb_helper_single_add_all_connectors(...);
@@
expression e1;
statement S;
@@
- e1 = drm_fb_helper_single_add_all_connectors(...);
- S
@@
@@
- drm_fb_helper_add_one_connector(...);
@@
@@
- drm_fb_helper_remove_one_connector(...);
Changes since v1:
* Squashed warning fixes into the patch that introduced the
warnings (into 5/7) (Laurent, Emil, Lyude)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305120434.111091-6-pankaj.laxminarayan.bharadiya@intel.com
Current code tries to store the link rate (in bps, which is a big
number) in a u8, which surely overflow. Then it's converted back to
bandwidth code (which is thus 0) and written to the chip.
The code sometimes works because the chip will automatically fallback to
the lowest possible DP link rate (1.62Gbps) when get the invalid value.
However, on the eDP panel of Olimex TERES-I, which wants 2.7Gbps link,
it failed.
As we had already read the link bandwidth as bandwidth code in earlier
code (to check whether it is supported), use it when setting bandwidth,
instead of converting it to link rate and then converting back.
Fixes: e1cff82c10 ("drm/bridge: fix anx6345 compilation for v5.5")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Torsten Duwe <duwe@lst.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221165127.813325-1-icenowy@aosc.io
Most bridge drivers create a DRM connector to model the connector at the
output of the bridge. This model is historical and has worked pretty
well so far, but causes several issues:
- It prevents supporting more complex display pipelines where DRM
connector operations are split over multiple components. For instance a
pipeline with a bridge connected to the DDC signals to read EDID data,
and another one connected to the HPD signal to detect connection and
disconnection, will not be possible to support through this model.
- It requires every bridge driver to implement similar connector
handling code, resulting in code duplication.
- It assumes that a bridge will either be wired to a connector or to
another bridge, but doesn't support bridges that can be used in both
positions very well (although there is some ad-hoc support for this in
the analogix_dp bridge driver).
In order to solve these issues, ownership of the connector should be
moved to the display controller driver (where it can be implemented
using helpers provided by the core).
Extend the bridge API to allow disabling connector creation in bridge
drivers as a first step towards the new model. The new flags argument to
the bridge .attach() operation allows instructing the bridge driver to
skip creating a connector. Unconditionally set the new flags argument to
0 for now to keep the existing behaviour, and modify all existing bridge
drivers to return an error when connector creation is not requested as
they don't support this feature yet.
The change is based on the following semantic patch, with manual review
and edits.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.attach = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
statement S, S1;
@@
int fn(
struct drm_bridge *bridge
+ , enum drm_bridge_attach_flags flags
)
{
... when != S
+ if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) {
+ DRM_ERROR("Fix bridge driver to make connector optional!");
+ return -EINVAL;
+ }
+
S1
...
}
@ depends on rule1 @
identifier rule1.fn;
identifier bridge, flags;
expression E1, E2, E3;
@@
int fn(
struct drm_bridge *bridge,
enum drm_bridge_attach_flags flags
) {
<...
drm_bridge_attach(E1, E2, E3
+ , flags
)
...>
}
@@
expression E1, E2, E3;
@@
drm_bridge_attach(E1, E2, E3
+ , 0
)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-10-laurent.pinchart@ideasonboard.com
Propagate bus format/flags so that the previous bridge element in the
chain knows which input format the panel bridge expects.
v11:
* Fix a typo in the subject
* Update the commit message so it's readable by itself
v10:
* Add changelog to the commit message
v8 -> v9:
* No changes
v7:
* Set atomic state hooks explicitly
v4 -> v6:
* Not part of the series
v3:
* Adjust things to match the new bus-format negotiation approach
* Use drm_atomic_helper_bridge_propagate_bus_fmt
* Don't implement ->atomic_check() (the core now takes care of bus
flags propagation)
v2:
* Adjust things to match the new bus-format negotiation approach
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128135514.108171-11-boris.brezillon@collabora.com
