Correct ldo1 voltage range from wrong high group(3.0V~3.3V) to low group
(1.6V~1.9V) because the ldo1 should be 1.8V. Actually, two voltage groups
have been supported at bd718x7-regulator driver, hence, just corrrect the
voltage range to 1.6V~3.3V. For ldo2@0.8V, correct voltage range too.
Otherwise, ldo1 would be kept @3.0V and ldo2@0.9V which violate i.mx8mn
datasheet as the below warning log in kernel:
[ 0.995524] LDO1: Bringing 1800000uV into 3000000-3000000uV
[ 0.999196] LDO2: Bringing 800000uV into 900000-900000uV
Fixes: 3e44dd0973 ("arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support")
Cc: stable@vger.kernel.org
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Each cpu-core is supposed to list its supply separately, add
supply for secondary cpus.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is used by the imx-ddrc devfreq driver to implement dynamic
frequency scaling of DRAM.
Support for proactive scaling via interconnect will come later. The
high-performance bus masters which need that (display, vpu, gpu) are
mostly not yet enabled in upstream anyway.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MN has different EVK boards to support different DDR types,
the ONLY differences are DDR chips and PMIC, so most of the devices
can be shared between these EVK boards, create a EVK dtsi file for
common use.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All nodes are better to follow alphabetical sort except iomuxc
which has huge pinctrl data, better to put it at the end of
file.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MN DDR4 EVK board has a GPIO LED to indicate status,
add support for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add A53 OPP table, cpu regulator and speed grading node to
support cpu-freq driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MN DDR4 EVK board, there is a rohm,bd71847 PMIC
on i2c1 bus, enable it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
