There are several issues with the bluetooth node - the wrong
compatible was used (because the bcm4329 compatible didn't exist
when the node was added), the max rate was incorrect (due to
limitations in the samsung TTY driver which have now been fixed),
the clocks were not assigned properly so some rates didn't work,
and the some pinctrl settings weren't explicitly set. Fix all
of the above issues.
While we're at it, update from the deprecated host-wakeup-gpios
property to the host-wake interrupt.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Aries boards have a BMA023 accelerometer attached over i2c-gpio.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Aries boards have a GP2A light/proximity sensor attached over i2c-gpio.
As the chip outputs a current and the board has no current ADC, a
current shunt resistor and a voltage ADC are used.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Correct the fuelgauge definition because only the fuelgauge on
fascinate4g has interrupt support (and even then it was wrong).
Also, assign the GPIO pinctrl so the interrupt is properly configured
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The GPH3 pins on s5pv210 have interrupt support and had the
interrupt-cells property but was missing the interrupt-controller
property.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add a node for the BCM4354 Bluetooth chip on the serial bus #0 on
the Exynos3250-based Artik5 boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
On Exynos5422/5800 the regulator supply for the A15 cores ("vdd_arm") is
coupled with the regulator supply for the SoC internal circuits
("vdd_int"), thus all operating points that modify one of those supplies
have to specify a triplet of the min/target/max values to properly work
with regulator coupling.
Fixes: eaffc4de16 ("ARM: dts: exynos: Add missing CPU frequencies for Exynos5422/5800")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Set smbus_en of IO expander to 1 in order to be able to read sensor.
Signed-off-by: Ben Pai <Ben_Pai@wistron.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The mailbox nodes defined in various dts files have been moved to
common dra7-ipu-dsp-common.dtsi and dra74-ipu-dsp-common.dtsi files
in commit a11a2f73b3 ("ARM: dts: dra7-ipu-dsp-common: Move mailboxes
into common files"), but the nodes were erroneously left out in the
dra7-evm-common.dtsi file. Fix this by removing these duplicate nodes.
Fixes: a11a2f73b3 ("ARM: dts: dra7-ipu-dsp-common: Move mailboxes into common files")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit 5390130f3b ("ARM: dts: dra7: add timer_sys_ck entries
for IPU/DSP timers") was added to allow the OMAP clocksource timer
driver to use the clock aliases when reconfiguring the parent clock
source for the timer functional clocks after the timer_sys_ck clock
aliases got cleaned up in commit a8202cd517 ("clk: ti: dra7: drop
unnecessary clock aliases").
The above patch however has missed adding the entries for couple of
timers (14, 15 and 16), and also added erroneously in the parent
ti-sysc nodes for couple of clocks (timers 4, 5 and 6). Fix these
properly, so that any of these timers can be used with OMAP remoteproc
IPU and DSP devices. The always-on timers 1 and 12 are not expected
to use this clock source, so they are not modified.
Fixes: 5390130f3b ("ARM: dts: dra7: add timer_sys_ck entries for IPU/DSP timers")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM335x TRM: Figure 16-23 define sysconfig register and soft_reset
are in first position corresponding to SYSC_OMAP4_SOFTRESET defined
in ti-sysc.h.
Fixes: 0782e8572c ("ARM: dts: Probe am335x musb with ti-sysc")
Signed-off-by: Oskar Holmlund <oskar@ohdata.se>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM335x TRM: Table 2-1 defines USBSS - USB Queue Manager in memory region
0x4740 0000 to 0x4740 7FFF.
Looks like the older TRM revisions list the range from 0x5000 to 0x8000
as reserved.
Fixes: 0782e8572c ("ARM: dts: Probe am335x musb with ti-sysc")
Signed-off-by: Oskar Holmlund <oskar@ohdata.se>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull USB/PHY driver updates from Greg KH:
"Here are the large set of USB and PHY driver updates for 5.8-rc1.
Nothing huge, just lots of little things:
- USB gadget fixes and additions all over the place
- new PHY drivers
- PHY driver fixes and updates
- XHCI driver updates
- musb driver updates
- more USB-serial driver ids added
- various USB quirks added
- thunderbolt minor updates and fixes
- typec updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (245 commits)
usb: dwc3: meson-g12a: fix USB2 PHY initialization on G12A and A1 SoCs
usb: dwc3: meson-g12a: fix error path when fetching the reset line fails
Revert "dt-bindings: usb: qcom,dwc3: Convert USB DWC3 bindings"
Revert "dt-bindings: usb: qcom,dwc3: Add compatible for SC7180"
Revert "dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver"
USB: serial: ch341: fix lockup of devices with limited prescaler
USB: serial: ch341: add basis for quirk detection
CDC-ACM: heed quirk also in error handling
USB: serial: option: add Telit LE910C1-EUX compositions
usb: musb: Fix runtime PM imbalance on error
usb: musb: jz4740: Prevent lockup when CONFIG_SMP is set
usb: musb: mediatek: add reset FADDR to zero in reset interrupt handle
usb: musb: use true for 'use_dma'
usb: musb: start session in resume for host port
usb: musb: return -ESHUTDOWN in urb when three-strikes error happened
USB: serial: qcserial: add DW5816e QDL support
thunderbolt: Add trivial .shutdown
usb: dwc3: keystone: Turn on USB3 PHY before controller
dt-bindings: usb: ti,keystone-dwc3.yaml: Add USB3.0 PHY property
dt-bindings: usb: convert keystone-usb.txt to YAML
...
Pull ARM devicetree updates from Arnd Bergmann:
"This is the set of device tree changes, mostly covering new hardware
support, with 577 patches touching a little over 500 files.
There are five new Arm SoCs supported in this release, all of them for
existing SoC families:
- Realtek RTD1195, RTD1395 and RTD1619 -- three SoCs used in both NAS
devices and Android Set-top-box designs, along with the
"Horseradish", "Lion Skin" and "Mjolnir" reference platforms; the
Mele X1000 and Xnano X5 set-top-boxes and the Banana Pi BPi-M4
single-board computer.
- Renesas RZ/G1H (r8a7742) -- a high-end 32-bit industrial SoC and
the iW-RainboW-G21D-Qseven-RZG1H board/SoM
- Rockchips RK3326 -- low-end 64-bit SoC along with the Odroid-GO
Advance game console
Newly added machines on already supported SoCs are:
- AMLogic S905D based Smartlabs SML-5442TW TV box
- AMLogic S905X3 based ODROID-C4 SBC
- AMLogic S922XH based Beelink GT-King Pro TV box
- Allwinner A20 based Olimex A20-OLinuXino-LIME-eMMC SBC
- Aspeed ast2500 based BMCs in Facebook x86 "Yosemite V2" and YADRO
OpenPower P9 "Nicole"
- Marvell Kirkwood based Check Point L-50 router
- Mediatek MT8173 based Elm/Hana Chromebook laptops
- Microchip SAMA5D2 "Industrial Connectivity Platform" reference
board
- NXP i.MX8m based Beacon i.MX8m-Mini SoM development kit
- Octavo OSDMP15x based Linux Automation MC-1 development board
- Qualcomm SDM630 based Xiaomi Redmi Note 7 phone
- Realtek RTD1295 based Xnano X5 TV Box
- STMicroelectronics STM32MP1 based Stinger96 single-board computer
and IoT Box
- Samsung Exynos4210 based based Samsung Galaxy S2 phone
- Socionext Uniphier based Akebi96 SBC
- TI Keystone based K2G Evaluation board
- TI am5729 based Beaglebone-AI development board
Include device descriptions for additional hardware support in
existing SoCs and machines based on all major SoC platforms:
- AMlogic Meson
- Allwinner sunxi
- Arm Juno/VFP/Vexpress/Integrator
- Broadcom bcm283x/bcm2711
- Hisilicon hi6220
- Marvell EBU
- Mediatek MT27xx, MT76xx, MT81xx and MT67xx
- Microchip SAMA5D2
- NXP i.MX6/i.MX7/i.MX8 and Layerscape
- Nvidia Tegra
- Qualcomm Snapdragon
- Renesas r8a77961, r8a7791
- Rockchips RK32xx/RK33xx
- ST-Ericsson ux500
- STMicroelectronics SMT32
- Samsung Exynos and S5PV210
- Socionext Uniphier
- TI OMAP5/DRA7 and Keystone"
* tag 'arm-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (564 commits)
ARM: dts: keystone: Rename "msmram" node to "sram"
arm: dts: mt2712: add uart APDMA to device tree
arm64: dts: mt8183: add mmc node
arm64: dts: mt2712: add ethernet device node
arm64: tegra: Make the RTC a wakeup source on Jetson Nano and TX1
ARM: dts: mmp3: Add the fifth SD HCI
ARM: dts: berlin*: Fix up the SDHCI node names
ARM: dts: mmp3: Fix USB & USB PHY node names
ARM: dts: mmp3: Fix L2 cache controller node name
ARM: dts: mmp*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa910: Fix the gpio interrupt cell number
ARM: dts: pxa3xx: Fix up encoding of the /gpio interrupts property
ARM: dts: pxa168: Fix the gpio interrupt cell number
ARM: dts: pxa168: Add missing address/size cells to i2c nodes
ARM: dts: dove: Fix interrupt controller node name
ARM: dts: kirkwood: Fix interrupt controller node name
arm64: dts: Add SC9863A emmc and sd card nodes
arm64: dts: Add SC9863A clock nodes
arm64: dts: mt6358: add PMIC MT6358 related nodes
...
Pull ARM SoC updates from Arnd Bergmann:
"One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already
supported in arch/arm64. The platform may also be extended to support
running 32-bit kernels on those 64-bit chips for memory-constrained
machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or
R8A7742, an eight-core chip based on Cortex-A15 and Cortex-A7 cores,
originally released in 2016 as one of the last high-end 32-bit
designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater
effort for the Android OS to have a common kernel binary for all
platforms and any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining. All
device drivers specific to those boards can now get removed as well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options"
* tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
ARM: omap2: fix omap5_realtime_timer_init definition
ARM: zynq: Don't select CONFIG_ICST
ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs
clk: versatile: Fix kconfig dependency on COMMON_CLK_VERSATILE
ARM: davinci: fix build failure without I2C
power: reset: vexpress: fix build issue
power: vexpress: cleanup: use builtin_platform_driver
power: vexpress: add suppress_bind_attrs to true
Revert "ARM: vexpress: Don't select VEXPRESS_CONFIG"
MAINTAINERS: pxa: remove Compulab arm/pxa support
ARM: pxa: remove Compulab pxa2xx boards
bus: arm-integrator-lm: Fix return value check in integrator_ap_lm_probe()
soc: imx: move cpu code to drivers/soc/imx
ARM: imx: move cpu definitions into a header
ARM: imx: use device_initcall for imx_soc_device_init
ARM: imx: pcm037: make pcm970_sja1000_platform_data static
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
...
Commit d9258898ad ("arm64: dts: arm: vexpress: Move fixed devices
out of bus node") moved the "mcc" DT node into the root node, because
it does not have any children using "reg" properties, so does violate
some dtc checks about "simple-bus" nodes.
However this broke the vexpress config-bus code, which walks up the
device tree to find the first node with an "arm,vexpress,site" property.
This gave the wrong result (matching the root node instead of the
motherboard node), so broke the clocks and some other devices for
VExpress boards.
Move the whole node back into its original position. This re-introduces
the dtc warning, but is conceptually the right thing to do. The dtc
warning seems to be overzealous here, there are discussions on fixing or
relaxing this check instead.
Link: https://lore.kernel.org/r/20200603162237.16319-1-andre.przywara@arm.com
Fixes: d9258898ad ("arm64: dts: vexpress: Move fixed devices out of bus node")
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
Pull timer updates from Thomas Gleixner:
"The truly boring timer and clocksource updates for 5.8:
- Not a single new clocksource or clockevent driver!
- Device tree updates for various chips
- Fixes and improvements and cleanups all over the place"
* tag 'timers-core-2020-06-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
dt-bindings: timer: Add renesas,em-sti bindings
clocksource/drivers/timer-versatile: Clear OF_POPULATED flag
clocksource: mips-gic-timer: Mark GIC timer as unstable if ref clock changes
clocksource: mips-gic-timer: Register as sched_clock
clocksource: dw_apb_timer_of: Fix missing clockevent timers
clocksource: dw_apb_timer: Affiliate of-based timer with any CPU
clocksource: dw_apb_timer: Make CPU-affiliation being optional
dt-bindings: timer: Move snps,dw-apb-timer DT schema from rtc
dt-bindings: rtc: Convert snps,dw-apb-timer to DT schema
clocksource/drivers/timer-ti-dm: Do one override clock parent in prepare()
clocksource/drivers/timer-ti-dm: Fix spelling mistake "detectt" -> "detect"
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
drivers/clocksource/arm_arch_timer: Remove duplicate error message
clocksource/drivers/arc_timer: Remove duplicate error message
clocksource/drivers/rda: drop redundant Kconfig dependency
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
...
ARM: Keystone DTS updates for 5.7
Add display support for K2G EVM Board
* tag 'keystone_dts_for_5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone-k2g-evm: add HDMI video support
ARM: dts: keystone-k2g: Add DSS node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We can currently sometimes get "RXS timed out" errors and "EOT timed out"
errors with spi transfers.
These errors can be made easy to reproduce by reading the cpcap iio
values in a loop while keeping the CPUs busy by also reading /dev/urandom.
The "RXS timed out" errors we can fix by adding spi-cpol and spi-cpha
in addition to the spi-cs-high property we already have.
The "EOT timed out" errors we can fix by increasing the spi clock rate
to 9.6 MHz. Looks similar MC13783 PMIC says it works at spi clock rates
up to 20 MHz, so let's assume we can pick any rate up to 20 MHz also
for cpcap.
Cc: maemo-leste@lists.dyne.org
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
The device node name should reflect generic class of a device so rename
the "msmram" node and its children to "sram". This will be also in sync
with upcoming DT schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Enable ethernet wake-on-lan feature for imx6q/dl/qp sabresd
boards since the PHY clock is supplied by external osc.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Update the imx6qdl gpr property to define gpr register
offset and bit in DT.
- Add imx6sx/imx6ul/imx7d ethernet stop mode property.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX device tree changes for 5.8:
- A series from Anson Huang updating SRC devices to match bindings
schema definition.
- Correct CPU supply name and add cpu1 supply for i.MX7D.
- Convert thermal device to use nvmem interface to get fuse data
for imx6qdl and imx6sl.
- A series from Tim Harvey to update imx6qdl-gw devices, adding support
of LSM9DS1 IIO imu/magn, USB OTG, bcm4330-bt, etc.
- Add input MUX for ENET2 MDIO into IMX7D pin functions.
- Misc random device addition or update.
* tag 'imx-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (22 commits)
ARM: dts: imx53-cx9020: Group port definitions for the dvi-converter
ARM: dts: imx5: make src node name generic
ARM: dts: imx50: Add src node interrupt
ARM: dts: imx: make src node name generic
ARM: dts: imx7d-pinfunc: add input mux for ENET2 mdio
ARM: dts: imx6sl: Use nvmem interface to get fuse data
ARM: dts: imx6qdl: Use nvmem interface to get fuse data
ARM: dts: imx6qdl-gw5910: fix wlan regulator
ARM: dts: imx6qdl-gw5910: add support for bcm4330-bt
ARM: dts: imx6qdl-gw5904: add lsm9ds1 iio imu/magn support
ARM: dts: imx6qdl-gw560x: add lsm9ds1 iio imu/magn support
ARM: dts: imx53: Add src node interrupt
ARM: dts: imx51: Add src node interrupt
ARM: dts: imx50: Remove unused iomuxc-gpr node
ARM: dts: imx6qdl-gw552x: add USB OTG support
ARM: dts: imx6-sr-som: add ethernet PHY configuration
arm: dts: ls1021atwr: Add QSPI node properties
ARM: dts: e60k02: add interrupt for PMIC
ARM: dts: colibri: introduce device trees with UHS-I support
ARM: dts: imx7d: Add cpu1 supply
...
Link: https://lore.kernel.org/r/20200523032516.11016-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM: dts: Amlogic updates for v5.8
- eth PHY and USB PHY updates
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson: Switch existing boards with RGMII PHY to "rgmii-id"
ARM: dts: meson: Add the Ethernet "timing-adjustment" clock
ARM: dts: meson8m2: Use the Meson8m2 specific USB2 PHY compatible
ARM: dts: meson: add the gadget mode properties to the USB0 controller
Link: https://lore.kernel.org/r/5ec6f524.1c69fb81.b979a.ae15@mx.google.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Few cpsw related dts fixes for omaps
Recent cpsw driver changes exposed few regressions in the cpsw related
dts configuration that would be good to fix:
- Few more boards still need to be updated to use rgmii-rxid phy caused
by the fallout from commit bcf3440c6d ("net: phy: micrel: add phy-mode
support for the KSZ9031 PHY" as the rx delay is now disabled unless we
use rgmii-rxid.
- On dm814x we have been using a wrong clock for mdio that now can produce
external abort on some boards
* tag 'omap-for-v5.7/cpsw-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix wrong mdio clock for dm814x
ARM: dts: am437x: fix networking on boards with ksz9031 phy
ARM: dts: am57xx: fix networking on boards with ksz9031 phy
Link: https://lore.kernel.org/r/pull-1589472123-367692@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
System timer changes for omaps for v5.8 merge window
This series of changes finally gets the legacy omap dual-mode timer and
32k counter system timer updated to use drivers/clocksource and device
tree data. And we can now remove the unused legacy platform data.
These changes are based on an immutable clocksource branch set up by
Daniel Lezcano.
* tag 'omap-for-v5.8/timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
ARM: dts: Configure system timers for omap3
ARM: dts: Configure system timers for omap5 and dra7
ARM: dts: Configure system timers for omap4
ARM: dts: Configure system timers for am437x
ARM: dts: Configure system timers for am335x
ARM: OMAP2+: Add omap_init_time_of()
bus: ti-sysc: Ignore timer12 on secure omap3
clk: ti: dm816: enable sysclk6_ck on init
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
Link: https://lore.kernel.org/r/pull-1590169577-735045@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Felipe writes:
USB: changes for v5.8 merge window
Rather busy cycle. We have a total 99 non-merge commits going into v5.8
merge window. The majority of the changes are in dwc3 this around (31.7%
of all changes). It's composed mostly Thinh's recent updates to get dwc3
to behave correctly with stream transfers. We have also have Roger's for
Keystone platforms and Neil's updates for the meson glue layer.
Apart from those, we have the usual set of non-critical fixes, new
device IDs, spelling fixes all over the place.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'usb-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (99 commits)
usb: dwc3: keystone: Turn on USB3 PHY before controller
dt-bindings: usb: ti,keystone-dwc3.yaml: Add USB3.0 PHY property
dt-bindings: usb: convert keystone-usb.txt to YAML
usb: dwc3: gadget: Check for prepared TRBs
usb: gadget: Fix issue with config_ep_by_speed function
usb: cdns3: ep0: delete the redundant status stage
usb: dwc2: Update Core Reset programming flow.
usb: gadget: fsl: Fix a wrong judgment in fsl_udc_probe()
usb: gadget: fix potential double-free in m66592_probe.
usb: cdns3: Fix runtime PM imbalance on error
usb: gadget: lpc32xx_udc: don't dereference ep pointer before null check
usb: dwc3: Increase timeout for CmdAct cleared by device controller
USB: dummy-hcd: use configurable endpoint naming scheme
usb: cdns3: gadget: assign interrupt number to USB gadget structure
usb: gadget: core: sync interrupt before unbind the udc
arm64: dts: qcom: sc7180: Add interconnect properties for USB
arm64: dts: qcom: sdm845: Add interconnect properties for USB
dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver
ARM: dts: at91: Remove the USB EP child node
dt-bindings: usb: atmel: Mark EP child node as deprecated
...
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.7, please pull the following:
- Vincent fixes the polarity of the ACT LED on the Raspberry Pi Zero W
board
- Hamish fixes the ARM PPI interrupts sensitivy for the Hurricane 2
SoCs
* tag 'arm-soc/for-5.7/devicetree-fixes-part2-v2' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: HR2: Fix PPI interrupt types
ARM: dts: bcm2835-rpi-zero-w: Fix led polarity
Link: https://lore.kernel.org/r/20200524203714.17035-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The endpoint configuration used to be stored in the device tree,
however the configuration depend on the "version" of the controller
itself.
Then the EP child node are useless and describe as deprecated in the
documentation binding: remove all the nodes from the SoC device tree
file. Remove also the #address-cells and #size-cells properties that
are no longer needed.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX fixes for 5.7, round 2:
One imx6q-bx50v3 device tree change to fix an issue, attempting atomic
modeset while using HDMI and display port at the same time causes LDB
clock programming to destroy the programming of HDMI.
* tag 'imx-fixes-5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts/imx6q-bx50v3: Set display interface clock parents
Link: https://lore.kernel.org/r/20200521150719.GB24084@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These were queued for v5.7 as bugfixes, merge them
here as well to resolve the conflicts.
* mmp/fixes:
ARM: dts: mmp3: Drop usb-nop-xceiv from HSIC phy
ARM: dts: mmp3-dell-ariel: Fix the SPI devices
ARM: dts: mmp3: Use the MMP3 compatible string for /clocks
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These three fixes should make it into linux-5.7 and
also into the branch for other mmp dt changes for v5.8,
so I created a branch for them.
* mmp/fixes:
ARM: dts: mmp3: Drop usb-nop-xceiv from HSIC phy
ARM: dts: mmp3-dell-ariel: Fix the SPI devices
ARM: dts: mmp3: Use the MMP3 compatible string for /clocks
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
