Use disable_irq_nosync() instead of disable_irq() as this might be
called in atomic context with netpoll.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dual_mac mode packets arrived on one port should not be forwarded by
switch hw to another port. Only Linux Host can forward packets between
ports. The below test case (reported in [1]) shows that packet arrived on
one port can be leaked to anoter (reproducible with dual port evms):
- connect port 1 (eth0) to linux Host 0 and run tcpdump or Wireshark
- connect port 2 (eth1) to linux Host 1 with vlan 1 configured
- ping <IPx> from Host 1 through vlan 1 interface.
ARP packets will be seen on Host 0.
Issue happens because dual_mac mode is implemnted using two vlans: 1 (Port
1+Port 0) and 2 (Port 2+Port 0), so there are vlan records created for for
each vlan. By default, the ALE will find valid vlan record in its table
when vlan 1 tagged packet arrived on Port 2 and so forwards packet to all
ports which are vlan 1 members (like Port.
To avoid such behaviorr the ALE VLAN ID Ingress Check need to be enabled
for each external CPSW port (ALE_PORTCTLn.VID_INGRESS_CHECK) so ALE will
drop ingress packets if Rx port is not VLAN member.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware requires that the ttl value for an encapsulating ipv4 tunnel
header be included as an action field. Prior to the support of Geneve
tunnel encap (when ttl set was removed completely), ttl value was
extracted from the tunnel key. However, tests have shown that this can
still produce a ttl of 0.
Fix the issue by setting the namespace default value for each new tunnel.
Follow up patch for net-next will do a full route lookup.
Fixes: 3ca3059dc3 ("nfp: flower: compile Geneve encap actions")
Fixes: b27d6a95a7 ("nfp: compile flower vxlan tunnel set actions")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Owing to a missing conditional, the result of rps_may_expire_flow() was
being ignored and filters were being removed even if we'd decided not to
expire them.
Fixes: f8d6203780 ("sfc: ARFS filter IDs")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx->type->filter_insert() returns an ID rather than the index that
efx->type->filter_async_insert() used to, which causes it to exceed
efx->type->max_rx_ip_filters on some EF10 configurations, leading to out-
of-bounds array writes.
So, in efx_filter_rfs_work(), convert this back into an index (which is
what the remove call in the expiry path expects, anyway).
Fixes: 3af0f34290 ("sfc: replace asynchronous filter operations")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-04-26
This pull request includes fixes for mlx5 core and netdev driver.
Please pull and let me know if there's any problems.
For -stable v4.12
net/mlx5e: TX, Use correct counter in dma_map error flow
For -stable v4.13
net/mlx5: Avoid cleaning flow steering table twice during error flow
For -stable v4.14
net/mlx5e: Allow offloading ipv4 header re-write for icmp
For -stable v4.15
net/mlx5e: DCBNL fix min inline header size for dscp
For -stable v4.16
net/mlx5: Fix mlx5_get_vector_affinity function
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When IGMP snooping is enabled on a bridge, traffic forwarded by an MDB
entry should be sent to both ports member in the MDB's ports list and
mrouter ports.
In case a port needs to be removed from an MDB's ports list, but this
port is also configured as an mrouter port, then do not update the
device so that it will continue to forward traffic through that port.
Fix a copy-paste error that checked that IGMP snooping is enabled twice
instead of checking the port's mrouter state.
Fixes: ded711c87a ("mlxsw: spectrum_switchdev: Consider mrouter status for mdb changes")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Colin King <colin.king@canonical.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding the DSA notifier, we will be sending DSA notifications with
info->master that is going to point to a particular net_device instance.
Our logic in bcm_sysport_map_queues() correctly disambiguates net_device
instances that are not covered by our own driver, but it will not make
sure that info->master points to a particular driver instance that we
are interested in. In a system where e.g: two or more SYSTEMPORT
instances are registered, this would lead in programming two or more
times the queue mapping, completely messing with the logic which does
the queue/port allocation and tracking.
Fix this by looking at the notifier_block pointer which is unique per
instance and allows us to go back to our driver private structure, and
in turn to the backing net_device instance.
Fixes: d156576362 ("net: systemport: Establish lower/upper queue mapping")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell's PPv2.2 IP needs an additional clock named "MG Core clock".
This is required on Armada 7K and 8K.
This commit adds the required clock in mvpp2, making sure it's only
used on PPv2.2.
Fixes: c7e92def1e ("clk: mvebu: cp110: Fix clock tree representation")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When clk_prepare_enable fails for the axi_clk, the mg_clk isn't properly
cleaned up. Add another jump label to handle that case, and make sure we
jump to it in the later error cases.
Fixes: 4792ea04bc ("net: mvpp2: Fix clock resource by adding an optional bus clock")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For very very old generation of the management FW Ethernet port
information table may theoretically not be available. This in
turn will cause the nfp_port structures to not be allocated.
Make sure we don't crash the kernel when there is no eth_tbl:
RIP: 0010:nfp_net_pci_probe+0xf2/0xb40 [nfp]
...
Call Trace:
nfp_pci_probe+0x6de/0xab0 [nfp]
local_pci_probe+0x47/0xa0
work_for_cpu_fn+0x1a/0x30
process_one_work+0x1de/0x3e0
Found while working with broken/development version of management FW.
Fixes: a5950182c0 ("nfp: map mac_stats and vf_cfg BARs")
Fixes: 93da7d9660 ("nfp: provide nfp_port to of nfp_net_get_mac_addr()")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deleting a flow counter, the modify mask should be the action and
the flow counter. Otherwise the flow counter is not deleted and we'll
get a firmware warning when deleting the remaining destinations on the
same FTE.
It only happens in the presence of flow counter and multiple vport
destinations. If there is only one vport destination, there is no
need to update the FTE when deleting the only vport destination,
we just delete the FTE.
Fixes: ae05831424 ("net/mlx5: Add option to add fwd rule with counter")
Signed-off-by: Chris Mi <chrism@mellanox.com>
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
After the cited commit, WQE RQ size is calculated based on sw_mtu but it
was not set for representors. This commit fixes that.
Fixes: 472a1e44b3 ("net/mlx5e: Save MTU in channels params")
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When we fail to initialize the RX root namespace, we need
to clean only that and not the entire flow steering.
Currently the code may try to clean the flow steering twice
on error witch leads to null pointer deference.
Make sure we clean correctly.
Fixes: fba53f7b57 ("net/mlx5: Introduce mlx5_flow_steering structure")
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In case of a dma_mapping_error, do not use wi->num_dma
as a parameter for dma unmap function because it's yet
to be set, and holds an out-of-date value.
Use actual value (local variable num_dma) instead.
Fixes: 34802a42b3 ("net/mlx5e: Do not modify the TX SKB")
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When the trust state is set to dscp and the netdev is down, the inline
header size is not updated. When netdev is up, the inline header size
stays at L2 instead of IP.
Fix this issue by updating the private parameter when the netdev is in
down so that when netdev is up, it picks up the right header size.
Fixes: fbcb127e89 ("net/mlx5e: Support DSCP trust state ...")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For ICMPv4, the checksum is calculated from the ICMP headers and data.
Since the ICMPv4 checksum doesn't cover the IP header, we can allow to
do L3 header re-write for this protocol.
Fixes: bdd66ac0ae ('net/mlx5e: Disallow TC offloading of unsupported match/action combinations')
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-04-24
This series contains fixes to ixgbevf, igb and ice drivers.
Colin Ian King fixes the return value on error for the new XDP support
that went into ixgbevf for 4.17.
Vinicius provides a fix for queue 0 for igb, which was not receiving all
the credits it needed when QAV mode was enabled.
Anirudh provides several fixes for the new ice driver, starting with
properly initializing num_nodes_added to zero. Fixed up a code comment
to better reflect what is really going on in the code. Fixed how to
detect if an OICR interrupt has occurred to a more reliable method.
Md Fahad fixes the ice driver to allocate the right amount of memory
when reading and storing the devices MAC addresses. The device can have
up to 2 MAC addresses (LAN and WoL), while WoL is currently not
supported, we need to ensure it can be properly handled when support is
added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For the MAC read operation, the device can return up to two (LAN and WoL)
MAC addresses. Without access to adequate memory, the device will return
an error. Fixed this by allocating the right amount of memory. Also, logic
to detect and copy the LAN MAC address into the port_info structure has
been added. Note that the WoL MAC address is ignored currently as the WoL
feature isn't supported yet.
Fixes: dc49c77236 ("ice: Get MAC/PHY/link info and scheduler topology")
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Associate an arbitrary ID with each ARFS filter, allowing to properly query
for expiry. The association is maintained in a hash table, which is
protected by a spinlock.
v3: fix build warnings when CONFIG_RFS_ACCEL is disabled (thanks lkp-robot).
v2: fixed uninitialised variable (thanks davem and lkp-robot).
Fixes: 3af0f34290 ("sfc: replace asynchronous filter operations")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hardware spec, checking the INTEVENT bit isn't a
reliable way to detect if an OICR interrupt has occurred. This is
because this bit can be cleared by the hardware/firmware before the
interrupt service routine has run. So instead, just check for OICR
events every time.
Fixes: 940b61af02 ("ice: Initialize PF and setup miscellaneous interrupt")
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_sched_add_nodes_to_layer is used recursively, and so we start
with num_nodes_added being 0. This way, in case of an error or if
num_nodes is NULL, the function just returns 0 to indicate that no
nodes were added.
Fixes: 5513b920a4 ("ice: Update Tx scheduler tree for VSI multi-Tx queue support")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When Qav mode is enabled, queue 0 should be kept on Stream Reservation
mode. From the i210 datasheet, section 8.12.19:
"Note: Queue0 QueueMode must be set to 1b when TransmitMode is set to
Qav." ("QueueMode 1b" represents the Stream Reservation mode)
The solution is to give queue 0 the all the credits it might need, so
it has priority over queue 1.
A situation where this can happen is when cbs is "installed" only on
queue 1, leaving queue 0 alone. For example:
$ tc qdisc replace dev enp2s0 handle 100: parent root mqprio num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 0
$ tc qdisc replace dev enp2s0 parent 100:2 cbs locredit -1470 \
hicredit 30 sendslope -980000 idleslope 20000 offload 1
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current error handling for failed resource setup for xdp_ring
data is a break out of the loop and returning 0 indicated everything
was OK, when in fact it is not. Fix this by exiting via the
error exit label err_setup_tx that will clean up the resources
correctly and return and error status.
Detected by CoverityScan, CID#1466879 ("Logically dead code")
Fixes: 21092e9ce8 ("ixgbevf: Add support for XDP_TX action")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The SFP eeprom indicates the transceiver signals (Rx LOS, Tx Fault, etc.)
that it supports. Update the driver to include checking the eeprom data
when deciding whether to use a transceiver signal.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update xgbe-phy-v2.c to make use of the auto-negotiation (AN) phy hooks
to improve the ability to successfully complete Clause 73 AN when running
at 10gbps. Hardware can sometimes have issues with CDR lock when the
AN DME page exchange is being performed.
The AN and KR training hooks are used as follows:
- The pre AN hook is used to disable CDR tracking in the PHY so that the
DME page exchange can be successfully and consistently completed.
- The post KR training hook is used to re-enable the CDR tracking so that
KR training can successfully complete.
- The post AN hook is used to check for an unsuccessful AN which will
increase a CDR tracking enablement delay (up to a maximum value).
Add two debugfs entries to allow control over use of the CDR tracking
workaround. The debugfs entries allow the CDR tracking workaround to
be disabled and determine whether to re-enable CDR tracking before or
after link training has been initiated.
Also, with these changes the receiver reset cycle that is performed during
the link status check can be performed less often.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hooks to the driver auto-negotiation (AN) flow to allow the different
phy implementations to perform any steps necessary to improve AN.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid using value stored in the login response buffer when
cleaning TX and RX buffer pools since these could be inconsistent
depending on the device state. Instead use the field in the driver's
private data that tracks the number of active pools.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPDMA_TX_PRIORITY_MAP in real is vlan pcp field priority mapping
register and basically replaces vlan pcp field for tagged packets.
So, set it to be 1:1 mapping. Otherwise, it will cause unexpected
change of egress vlan tagged packets, like prio 2 -> prio 5.
Fixes: e05107e6b7 ("net: ethernet: ti: cpsw: add multi queue support")
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some firmware images, the length of BNX_DIR_TYPE_PKG_LOG nvram type
could be greater than the fixed buffer length of 4096 bytes allocated by
the driver. This was causing HWRM_NVM_READ to copy more data to the buffer
than the allocated size, causing general protection fault.
Fix the issue by allocating the exact buffer length returned by
HWRM_NVM_FIND_DIR_ENTRY, instead of 4096. Move the kzalloc() call
into the bnxt_get_pkgver() function.
Fixes: 3ebf6f0a09 ("bnxt_en: Add installed-package firmware version reporting via Ethtool GDRVINFO")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When longer interface names are used, the action names exposed in
/proc/interrupts and /proc/irq/* maybe truncated. For example, when
using the predictable name algorithm in systemd on a HiSilicon D05,
I see:
ubuntu@d05-3:~$ grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
enahisic2i0-tx0
enahisic2i0-tx1
[...]
enahisic2i0-tx8
enahisic2i0-tx9
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
Increase the max ring name length to allow for an interface name
of IFNAMSIZE. After this change, I now see:
$ grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
enahisic2i0-tx0
enahisic2i0-tx1
enahisic2i0-tx2
[...]
enahisic2i0-tx8
enahisic2i0-tx9
enahisic2i0-tx10
enahisic2i0-tx11
enahisic2i0-tx12
enahisic2i0-tx13
enahisic2i0-tx14
enahisic2i0-tx15
Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ACS Feature is currently enabled for GMAC >= 4 but the llc_snap status
is never checked in descriptor rx_status callback. This will cause
stmmac to always strip packets even that ACS feature is already
stripping them.
Lets be safe and disable the ACS feature for GMAC >= 4 and always strip
the packets for this GMAC version.
Fixes: 477286b53f ("stmmac: add GMAC4 core support")
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPv2 TX/RX descriptors uses 40bits DMA addresses, but 41 bits masks were
used (GENMASK_ULL(40, 0)).
This commit fixes that by using the correct mask.
Fixes: e7c5359f2e ("net: mvpp2: introduce PPv2.2 HW descriptors and adapt accessors")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the last rmnet device attached to a real device is removed, the
real device is unregistered from rmnet. As a result, the real device
lookup fails resulting in a warning when the fill_info handler is
called as part of the rmnet device unregistration.
Fix this by returning the rmnet flags as 0 when no real device is
present.
WARNING: CPU: 0 PID: 1779 at net/core/rtnetlink.c:3254
rtmsg_ifinfo_build_skb+0xca/0x10d
Modules linked in:
CPU: 0 PID: 1779 Comm: ip Not tainted 4.16.0-11872-g7ce2367 #1
Stack:
7fe655f0 60371ea3 00000000 00000000
60282bc6 6006b116 7fe65600 60371ee8
7fe65660 6003a68c 00000000 900000000
Call Trace:
[<6006b116>] ? printk+0x0/0x94
[<6001f375>] show_stack+0xfe/0x158
[<60371ea3>] ? dump_stack_print_info+0xe8/0xf1
[<60282bc6>] ? rtmsg_ifinfo_build_skb+0xca/0x10d
[<6006b116>] ? printk+0x0/0x94
[<60371ee8>] dump_stack+0x2a/0x2c
[<6003a68c>] __warn+0x10e/0x13e
[<6003a82c>] warn_slowpath_null+0x48/0x4f
[<60282bc6>] rtmsg_ifinfo_build_skb+0xca/0x10d
[<60282c4d>] rtmsg_ifinfo_event.part.37+0x1e/0x43
[<60282c2f>] ? rtmsg_ifinfo_event.part.37+0x0/0x43
[<60282d03>] rtmsg_ifinfo+0x24/0x28
[<60264e86>] dev_close_many+0xba/0x119
[<60282cdf>] ? rtmsg_ifinfo+0x0/0x28
[<6027c225>] ? rtnl_is_locked+0x0/0x1c
[<6026ca67>] rollback_registered_many+0x1ae/0x4ae
[<600314be>] ? unblock_signals+0x0/0xae
[<6026cdc0>] ? unregister_netdevice_queue+0x19/0xec
[<6026ceec>] unregister_netdevice_many+0x21/0xa1
[<6027c765>] rtnl_delete_link+0x3e/0x4e
[<60280ecb>] rtnl_dellink+0x262/0x29c
[<6027c241>] ? rtnl_get_link+0x0/0x3e
[<6027f867>] rtnetlink_rcv_msg+0x235/0x274
Fixes: be81a85f5f ("net: qualcomm: rmnet: Implement fill_info")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some firmware variants - specifically 'capture packed stream' - RSS
filters are not valid. We must check if RSS is actually active rather
than merely enabled.
Fixes: 42356d9a13 ("sfc: support RSS spreading of ethtool ntuple filters")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a firmware bug, the hypervisor can send an interrupt to a
transmit or receive queue just prior to a partition migration, not
allowing the device enough time to handle it and send an EOI. When
the partition migrates, the interrupt is lost but an "EOI-pending"
flag for the interrupt line is still set in firmware. No further
interrupts will be sent until that flag is cleared, effectively
freezing that queue. To workaround this, the driver will disable the
hardware interrupt and send an H_EOI signal prior to re-enabling it.
This will flush the pending EOI and allow the driver to continue
operation.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell's PPv2 controller has a Packet Header parser, which uses a
fixed-size TCAM array of filter entries.
The mvpp2 driver reserves some ranges among the 256 TCAM entries to
perform MAC and VID filtering. The rest of the TCAM ids are freely usable
for other features, such as IPv4 proto matching.
This commit fixes the MVPP2_PE_LAST_FREE_TID define that sets the end of
the "free range", which included the MAC range. This could therefore allow
some other features to use entries dedicated to MAC filtering,
lowering the number of unicast/multicast addresses that could be allowed
before switching to promiscuous mode.
Fixes: 10fea26ce2 ("net: mvpp2: Add support for unicast filtering")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A misconfigured system (e.g. with all interrupts affinitised to all CPUs)
may produce a storm of ARFS steering events. With the existing sfc ARFS
implementation, that could create a backlog of workitems that grinds the
system to a halt. To prevent this, limit the number of workitems that
may be in flight for a given SFC device to 8 (EFX_RPS_MAX_IN_FLIGHT), and
return EBUSY from our ndo_rx_flow_steer method if the limit is reached.
Given this limit, also store the workitems in an array of slots within the
struct efx_nic, rather than dynamically allocating for each request.
The limit should not negatively impact performance, because it is only
likely to be hit in cases where ARFS will be ineffective anyway.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we inserted an ARFS filter for ndo_rx_flow_steer(), we didn't know
what the filter ID would be, so we just returned 0. Thus, we must also
pass 0 as the filter ID when calling rps_may_expire_flow() for it, and
rely on the flow_id to identify what we're talking about.
Fixes: 3af0f34290 ("sfc: replace asynchronous filter operations")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Necessary to allow redirecting a flow when the application moves.
Fixes: 3af0f34290 ("sfc: replace asynchronous filter operations")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a second skb list for handling control messages and limit the
number of allowed messages. Some control messages are considered more
crucial than others, resulting in the need for a second skb list. By
splitting the list into a separate high and low priority list we can
ensure that messages on the high list get added to the head of the list
that gets processed, this however has no functional impact. Previously
there was no limit on the number of messages allowed on the queue, this
could result in the queue growing boundlessly and eventually the host
running out of memory.
Fixes: b985f870a5 ("nfp: process control messages in workqueue in flower app")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we processed the route ack control messages in the workqueue,
this unnecessarily loads the workqueue. We can deal with these messages
sooner as we know we are going to drop them.
Fixes: 8e6a9046b6 ("nfp: flower vxlan neighbour offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
