Remove spin_lock_irqsave in stm32_config_rs485, it cause recursive locking.
Already locked in uart_set_rs485_config.
Fixes: 1bcda09d29 ("serial: stm32: add support for RS485 hardware control mode")
Signed-off-by: Borut Seljak <borut.seljak@t-2.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Deferred probe is an expected return value for clk_get() on many
platforms. The driver deals with it properly, so there's no need
to output a warning that may potentially confuse users.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_info() is more appropriate for printing messages inside drivers, so
switch to dev_info().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_info() is more appropriate for printing messages inside drivers, so
switch to dev_info().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to support Rx in-band wakeup, we need to enable irq wake on an
edge sensitive interrupt of Rx pin before suspend and disable it when
resuming.
This interrupt is used only as wake source to resume the system when
suspended. Note that the sent character will be lost as the controller is
actually suspended.
We use this to support wakeup on bluetooth. Bluetooth will repeatedly send
0xFD to wakeup host. Once host detects Rx falling, an interrupt is
triggered, and the system leaves sleep state. Then, the bluetooth driver
will send 0xFC to bluetooth and bluetooth can start to send normal HCI
packets.
Signed-off-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the cable is not connected then the target gets into
an infinite wait for tx empty.
Add a timeout to the tx empty wait.
Reported-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we are doing a read of the status register.
Move the spinlock after that as the reads need not be spinlock
protected. This patch prevents relaxing the cpu with spinlock held.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When modprobe/rmmod/modprobe module, if platform_driver_register() fails,
the kernel complained,
proc_dir_entry 'driver/digicolor-usart' already registered
WARNING: CPU: 1 PID: 5636 at fs/proc/generic.c:360 proc_register+0x19d/0x270
Fix this by adding uart_unregister_driver() when platform_driver_register() fails.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix sparse warning:
drivers/tty/serial/stm32-usart.c:603:14: warning:
symbol 'stm32_get_databits' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Select either pinctrl sleep state in suspend function or default state in
resume function.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 84ecc2f6eb.
con_insert_unipair() is working with a sparse 3-dimensional array:
- p->uni_pgdir[] is the top layer
- p1 points to a middle layer
- p2 points to a bottom layer
If it needs to allocate a new middle layer, and then fails to allocate
a new bottom layer, it would previously free only p2, and now it frees
both p1 and p2. But since the new middle layer was already registered
in the top layer, it was not leaked.
However, if it looks up an *existing* middle layer and then fails to
allocate a bottom layer, it now frees both p1 and p2 but does *not*
free any other bottom layers under p1. So it *introduces* a memory
leak.
The error path also cleared the wrong index in p->uni_pgdir[],
introducing a use-after-free.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 84ecc2f6eb ("consolemap: Fix a memory leaking bug in drivers/tty/vt/consolemap.c")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As suggested by Uwe, add a note indicating that the modem control
signals do not support interrupts, which precludes the driver from
using mctrl_gpio_init().
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Add support for the generic mctrl gpio helper. This will allow us to
convert several board files to use the gpiod tables to assign GPIOs to
serial ports, rather than needing to have private function callbacks.
If the generic mctrl gpio helper fails, ignore the mctrl gpios rather
than preventing the (possibly console) serial port from being created.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
After memory allocation failure vc_allocate() doesn't clean up data
which has been initialized in visual_init(). In case of fbcon this
leads to divide-by-0 in fbcon_init() on next open of the same tty.
memory allocation in vc_allocate() may fail here:
1097: vc->vc_screenbuf = kzalloc(vc->vc_screenbuf_size, GFP_KERNEL);
on next open() fbcon_init() skips vc_font.data initialization:
1088: if (!p->fontdata) {
division by zero in fbcon_init() happens here:
1149: new_cols /= vc->vc_font.width;
Additional check is needed in fbcon_deinit() to prevent
usage of uninitialized vc_screenbuf:
1251: if (vc->vc_hi_font_mask && vc->vc_screenbuf)
1252: set_vc_hi_font(vc, false);
Crash:
#6 [ffffc90001eafa60] divide_error at ffffffff81a00be4
[exception RIP: fbcon_init+463]
RIP: ffffffff814b860f RSP: ffffc90001eafb18 RFLAGS: 00010246
...
#7 [ffffc90001eafb60] visual_init at ffffffff8154c36e
#8 [ffffc90001eafb80] vc_allocate at ffffffff8154f53c
#9 [ffffc90001eafbc8] con_install at ffffffff8154f624
...
Signed-off-by: Grzegorz Halat <ghalat@redhat.com>
Reviewed-by: Oleksandr Natalenko <oleksandr@redhat.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the RELEVANT_IFLAG() macro which hasn't been used at least since
the dawn of git.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_lookup_driver take a reference to the struct tty_driver, but forget
to release it on the error path, lead to a memory leak.
add a tty_driver_kref_put before error return.
Signed-off-by: Lin Yi <teroincn@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After memory allocation failure vc_allocate() doesn't clean up data
which has been initialized in visual_init(). In case of fbcon this
leads to divide-by-0 in fbcon_init() on next open of the same tty.
memory allocation in vc_allocate() may fail here:
1097: vc->vc_screenbuf = kzalloc(vc->vc_screenbuf_size, GFP_KERNEL);
on next open() fbcon_init() skips vc_font.data initialization:
1088: if (!p->fontdata) {
division by zero in fbcon_init() happens here:
1149: new_cols /= vc->vc_font.width;
Additional check is needed in fbcon_deinit() to prevent
usage of uninitialized vc_screenbuf:
1251: if (vc->vc_hi_font_mask && vc->vc_screenbuf)
1252: set_vc_hi_font(vc, false);
Crash:
#6 [ffffc90001eafa60] divide_error at ffffffff81a00be4
[exception RIP: fbcon_init+463]
RIP: ffffffff814b860f RSP: ffffc90001eafb18 RFLAGS: 00010246
...
#7 [ffffc90001eafb60] visual_init at ffffffff8154c36e
#8 [ffffc90001eafb80] vc_allocate at ffffffff8154f53c
#9 [ffffc90001eafbc8] con_install at ffffffff8154f624
...
Signed-off-by: Grzegorz Halat <ghalat@redhat.com>
Reviewed-by: Oleksandr Natalenko <oleksandr@redhat.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function con_insert_unipair(), when allocation for p2 and p1[n]
fails, ENOMEM is returned, but previously allocated p1 is not freed,
remains as leaking memory. Thus we should free p1 as well when this
allocation fails.
Signed-off-by: Gen Zhang <blackgod016574@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SMC relocation can also be activated earlier by the bootloader,
so the driver's behaviour cannot rely on selected kernel config.
When the SMC is relocated, CPM_CR_INIT_TRX cannot be used.
But the only thing CPM_CR_INIT_TRX does is to clear the
rstate and tstate registers, so this can be done manually,
even when SMC is not relocated.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 9ab9212014 ("cpm_uart: fix non-console port startup bug")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checks the returned values of platform_get_irq() for both required
"event" and optional "wakeup" IRQs during probe. This allows the driver
probe to be deferred if needed.
Removes redundant checks for 'cfg.has_wakeup'.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds a check on the Transmission Complete bit status before closing the
com port. Prevents the port closure before the end of the transmission.
TC poll loop is moved from stm32_tx_dma_complete to stm32_shutdown
routine, in order to check TC before shutdown in both dma and
PIO tx modes.
TC clear is added in stm32_transmit_char routine, in order to be cleared
before transmitting in both dma and PIO tx modes.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disables the tx irq when the transmission is ended and updates stop_tx
conditions for code cleanup.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fixes a rx data error when data length < 8 bits and parity is enabled.
RDR register MSB is used for parity bit reception.
- Adds a mask to ignore MSB when data is get from RDR.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fixes parity and framing error bit by clearing parity and framing error
flag. The current implementation doesn't clear the error bits when an
error is detected.
- Fixes the incorrect name of framing error clearing flag in header file.
- Fixes misalignement between data frame and errors status. The status
read for "n" frame was the status of "n+1" frame".
- Fixes break detection was not triggered by the expected register.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32 supports either:
- 8 and 9 bits word length (including parity bit) for stm32f4 compatible
devices
- 7, 8 and 9 bits word length (including parity bit) for stm32f7 and
stm32h7 compatible devices.
As a consequence STM32 supports the following termios configurations:
- CS7 with parity bit, and CS8 (with or without parity bit) for stm32f4
compatible devices.
- CS6 with parity bit, CS7 and CS8 (with or without parity bit) for
stm32f7 and stm32h7 compatible devices.
This patch is fixing word length by configuring correctly the SoC with
supported configurations.
Fixes: ada8618ff3 ("serial: stm32: adding support for stm32f7")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The datasheet states:
Bit 4: ClockEnSet the ClockEn bit high to enable an external clocking
(crystal or clock generator at XIN). Set the ClockEn bit to 0 to disable
clocking
Bit 1: CrystalEnSet the CrystalEn bit high to enable the crystal
oscillator. When using an external clock source at XIN, CrystalEn must
be set low.
The bit 4, MAX310X_CLKSRC_EXTCLK_BIT, should be set and was not.
This was required to make the MAX3107 with an external crystal on our
board able to send or receive data.
Signed-off-by: Joe Burmeister <joe.burmeister@devtank.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each time the DMA engine signals a transaction error the driver prints
a message at error level. Getting transaction errors is pretty much
expected on baudrate mismatches and the correspoding error counters
are increased in this case properly. Remove the error message which
is possibly repeated at a very high rate which can lock up the whole
system.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the tty layer requests the uart to throttle, the current code
executing in msm_serial will trigger "Bad mode in Error Handler" and
generate an invalid stack frame in pstore before rebooting (that is if
pstore is indeed configured: otherwise the user shall just notice a
reboot with no further information dumped to the console).
This patch replaces the PIO byte accessor with the word accessor
already used in PIO mode.
Fixes: 68252424a7 ("tty: serial: msm: Support big-endian CPUs")
Cc: stable@vger.kernel.org
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Batch read mode doesn't check any conditions or flags except the Rx
overflow one. But it may only happen after the last character is pushed
into the RHR register. In this case we shouldn't push all the read
characters with overrun flag set, but only the last one caused the
FIFO overflow. This commit splits the characters retrieval loop into
two parts. First one is ordinary intsert-chars procedure without taking
the overrun status into account. Second part inserts the last character
checking whether the overrun happened and pushing a '\0' character with
TTY_OVERRUN flag to a flip-buffer.
If we left the loop the way it was the '\0' character would be inserted
after each character retrieved at the overrun occasion.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART port might be pre-configured with rs485 enabled flag at the
time of the port starting up process. In this case we need to
have the hardware rs485-related registers initialized in accordance
with the rs485 flags and settings provided by the configs descriptor.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently sets the echo suppression bit by default when rs485
is enabled. Naturally it disables any data retrieval in rs485 mode while
RTSn is pushed up. The receiver gate (RX_) can be enabled just by clearing
(or not setting) the EchoSuprs bit of mode2 register. So by setting or
clearing the bit we implement the SER_RS485_RX_DURING_TX rs485 flag
support.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current calculator doesn't do it' job quite correct. First of all the
max310x baud-rates generator supports the divisor being less than 16.
In this case the x2/x4 modes can be used to double or quadruple
the reference frequency. But the current baud-rate setter function
just filters all these modes out by the first condition and setups
these modes only if there is a clocks-baud division remainder. The former
doesn't seem right at all, since enabling the x2/x4 modes causes the line
noise tolerance reduction and should be only used as a last resort to
enable a requested too high baud-rate.
Finally the fraction is supposed to be calculated from D = Fref/(c*baud)
formulae, but not from D % 16, which causes the precision loss. So to speak
the current baud-rate calculator code works well only if the baud perfectly
fits to the uart reference input frequency.
Lets fix the calculator by implementing the algo fully compliant with
the fractional baud-rate generator described in the datasheet:
D = Fref / (c*baud), where c={16,8,4} is the x1/x2/x4 rate mode
respectively, Fref - reference input frequency. The divisor fraction is
calculated from the same formulae, but making sure it is found with a
resolution of 0.0625 (four bits).
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPI transfer tx/rx buffers must be DMA-safe and the structure
documentation clearly states this. Data declared on the system stack isn't
DMA-safe [1]. Instead at least kernel memory should be used for the
buffers. In order to fix this here we can create the buffers at the device
probing stage and use them without any synchronization, since batch
read/write methods are called from non-reentrant contexts - either from
rx-event IRQ threaded handler or from the tx workqueue item.
[1] Documentation/DMA-API-HOWTO.txt
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_port structure instance is embedded into the max310x_one
super-structure, which is accessed by some of the uart-port callback
methods. In order to improve the callback's code readability lets
define the to_max310x_port() wrapper which just translates the passed
uart_port pointer to the max310x_one one. It is also going to be
handy in future commits.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since cmwq introduction in the kernel, workqueues've been turned into
non-reentrant execution contexts [1]. It means any work item is
guaranteed to be executed by at most one worker system-wide at any
given time. Since tx-handler max310x_handle_tx() is called by a
single work item we don't need it to be self-protected by the mutex.
We also don't need to check the tx work item pending state before
scheduling it (which in the first place was racy btw), since cmwq will
make sure to reschedule the item if it wasn't pending at the moment of
schedule_work() call.
[1] Documentation/core-api/workqueue.rst
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PL011 register space includes all necessary status bits to
determine whether a device instance requires handling in response
to an interrupt. Therefore, multiple instances of the device could
be serviced by a single shared interrupt, which is the case on BCM7211.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_dbg statement should print the value of uart.port.mapbase instead
of its address. Besides that, uart.port.irq and uart.port.iotype are all
unsigned types, so using %u is more appropriate.
Signed-off-by: Hao Lee <haolee.swjtu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull RISC-V updates from Palmer Dabbelt:
"This contains an assortment of RISC-V related patches that I'd like to
target for the 5.2 merge window. Most of the patches are cleanups, but
there are a handful of user-visible changes:
- The nosmp and nr_cpus command-line arguments are now supported,
which work like normal.
- The SBI console no longer installs itself as a preferred console,
we rely on standard mechanisms (/chosen, command-line, hueristics)
instead.
- sfence_remove_sfence_vma{,_asid} now pass their arguments along to
the SBI call.
- Modules now support BUG().
- A missing sfence.vma during boot has been added. This bug only
manifests during boot.
- The arch/riscv support for SiFive's L2 cache controller has been
merged, which should un-block the EDAC framework work.
I've only tested this on QEMU again, as I didn't have time to get
things running on the Unleashed. The latest master from this morning
merges in cleanly and passes the tests as well"
* tag 'riscv-for-linus-5.2-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux: (31 commits)
riscv: fix locking violation in page fault handler
RISC-V: sifive_l2_cache: Add L2 cache controller driver for SiFive SoCs
RISC-V: Add DT documentation for SiFive L2 Cache Controller
RISC-V: Avoid using invalid intermediate translations
riscv: Support BUG() in kernel module
riscv: Add the support for c.ebreak check in is_valid_bugaddr()
riscv: support trap-based WARN()
riscv: fix sbi_remote_sfence_vma{,_asid}.
riscv: move switch_mm to its own file
riscv: move flush_icache_{all,mm} to cacheflush.c
tty: Don't force RISCV SBI console as preferred console
RISC-V: Access CSRs using CSR numbers
RISC-V: Add interrupt related SCAUSE defines in asm/csr.h
RISC-V: Use tabs to align macro values in asm/csr.h
RISC-V: Fix minor checkpatch issues.
RISC-V: Support nr_cpus command line option.
RISC-V: Implement nosmp commandline option.
RISC-V: Add RISC-V specific arch_match_cpu_phys_id
riscv: vdso: drop unnecessary cc-ldoption
riscv: call pm_power_off from machine_halt / machine_power_off
...
The Linux kernel will auto-disables all boot consoles whenever it
gets a preferred real console.
Currently on RISC-V systems, if we have a real console which is not
RISCV SBI console then boot consoles (such as earlycon=sbi) are not
auto-disabled when a real console (ttyS0 or ttySIF0) is available.
This results in duplicate prints at boot-time after kernel starts
using real console (i.e. ttyS0 or ttySIF0) if "earlycon=" kernel
parameter was passed by bootloader.
The reason for above issue is that RISCV SBI console always adds
itself as preferred console which is causing other real consoles
to be not used as preferred console.
Ideally "console=" kernel parameter passed by bootloaders should
be the one selecting a preferred real console.
This patch fixes above issue by not forcing RISCV SBI console as
preferred console.
Fixes: afa6b1ccfa ("tty: New RISC-V SBI console driver")
Cc: stable@vger.kernel.org
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
When kernel panic happens, it will first print the panic call stack,
then the ending msg like:
[ 35.743249] ---[ end Kernel panic - not syncing: Fatal exception
[ 35.749975] ------------[ cut here ]------------
The above message are very useful for debugging.
But if system is configured to not reboot on panic, say the
"panic_timeout" parameter equals 0, it will likely print out many noisy
message like WARN() call stack for each and every CPU except the panic
one, messages like below:
WARNING: CPU: 1 PID: 280 at kernel/sched/core.c:1198 set_task_cpu+0x183/0x190
Call Trace:
<IRQ>
try_to_wake_up
default_wake_function
autoremove_wake_function
__wake_up_common
__wake_up_common_lock
__wake_up
wake_up_klogd_work_func
irq_work_run_list
irq_work_tick
update_process_times
tick_sched_timer
__hrtimer_run_queues
hrtimer_interrupt
smp_apic_timer_interrupt
apic_timer_interrupt
For people working in console mode, the screen will first show the panic
call stack, but immediately overridden by these noisy extra messages,
which makes debugging much more difficult, as the original context gets
lost on screen.
Also these noisy messages will confuse some users, as I have seen many bug
reporters posted the noisy message into bugzilla, instead of the real
panic call stack and context.
Adding a flag "suppress_printk" which gets set in panic() to avoid those
noisy messages, without changing current kernel behavior that both panic
blinking and sysrq magic key can work as is, suggested by Petr Mladek.
To verify this, make sure kernel is not configured to reboot on panic and
in console
# echo c > /proc/sysrq-trigger
to see if console only prints out the panic call stack.
Link: http://lkml.kernel.org/r/1551430186-24169-1-git-send-email-feng.tang@intel.com
Signed-off-by: Feng Tang <feng.tang@intel.com>
Suggested-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull dmaengine updates from Vinod Koul:
- Updates to stm32 dma residue calculations
- Interleave dma capability to axi-dmac and support for ZynqMP arch
- Rework of channel assignment for rcar dma
- Debugfs for pl330 driver
- Support for Tegra186/Tegra194, refactoring for new chips and support
for pause/resume
- Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma, rcar-dmac,
stm32-dma etc
- dev_get_drvdata() updates on few drivers
* tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (34 commits)
dmaengine: tegra210-adma: restore channel status
dmaengine: tegra210-dma: free dma controller in remove()
dmaengine: tegra210-adma: add pause/resume support
dmaengine: tegra210-adma: add support for Tegra186/Tegra194
Documentation: DT: Add compatibility binding for Tegra186
dmaengine: tegra210-adma: prepare for supporting newer Tegra chips
dmaengine: at_xdmac: remove a stray bottom half unlock
dmaengine: fsl-edma: Adjust indentation
dmaengine: fsl-edma: Fix typo in Vybrid name
dmaengine: stm32-dma: fix residue calculation in stm32-dma
dmaengine: nbpfaxi: Use dev_get_drvdata()
dmaengine: bcm-sba-raid: Use dev_get_drvdata()
dmaengine: stm32-dma: Fix unsigned variable compared with zero
dmaengine: stm32-dma: use platform_get_irq()
dmaengine: rcar-dmac: Update copyright information
dmaengine: imx-sdma: Only check ratio on parts that support 1:1
dmaengine: xgene-dma: fix spelling mistake "descripto" -> "descriptor"
dmaengine: idma64: Move driver name to the header
dmaengine: bcm2835: Drop duplicate capability setting.
dmaengine: pl330: _stop: clear interrupt status
...
Pull tty/serial updates from Greg KH:
"Here is the "big" set of tty/serial driver patches for 5.2-rc1.
It's really pretty small, not much happening in this portion of the
kernel at the moment. When the "highlight" is the movement of the
documentation from .txt to .rst files, it's a good merge window.
There's a number of small fixes and updates over the various serial
drivers, and a new "tty null" driver for those embedded systems that
like to make things even smaller and not break things.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (45 commits)
tty: serial: add driver for the SiFive UART
dt-bindings: serial: add documentation for the SiFive UART driver
serial: uartps: Add support for cts-override
dt-bindings: xilinx-uartps: Add support for cts-override
serial: milbeaut_usio: Fix error handling in probe and remove
tty: rocket: deprecate the rp_ioctl
tty: rocket: Remove RCPK_GET_STRUCT ioctl
tty: update obsolete termios comment
tty: serial_core: fix error code returned by uart_register_driver()
serial: 8250-mtk: modify baudrate setting
serial: 8250-mtk: add follow control
docs: serial: convert docs to ReST and rename to *.rst
serial: 8250_exar: Adjust IOT2000 matching
TTY: serial_core, add ->install
serial: Fix using plain integer instead of Null pointer
tty:serial_core: Spelling mistake
tty: Add NULL TTY driver
tty: vt: keyboard: Allow Unicode compose base char
Revert "tty: fix NULL pointer issue when tty_port ops is not set"
serial: Add Milbeaut serial control
...
Pull staging / IIO driver updates from Greg KH:
"Here is the big staging and iio driver update for 5.2-rc1.
Lots of tiny fixes all over the staging and IIO driver trees here,
along with some new IIO drivers.
The "counter" subsystem was added in here as well, as it is needed by
the IIO drivers and subsystem.
Also we ended up deleting two drivers, making this pull request remove
a few hundred thousand lines of code, always a nice thing to see. Both
of the drivers removed have been replaced with "real" drivers in their
various subsystem directories, and they will be coming to you from
those locations during this merge window.
There are some core vt/selection changes in here, that was due to some
cleanups needed for the speakup fixes. Those have all been acked by
the various subsystem maintainers (i.e. me), so those are ok.
We also added a few new drivers, for some odd hardware, giving new
developers plenty to work on with basic coding style cleanups to come
in the near future.
Other than that, nothing unusual here.
All of these have been in linux-next for a while with no reported
issues, other than an odd gcc warning for one of the new drivers that
should be fixed up soon"
[ I fixed up the warning myself - Linus ]
* tag 'staging-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (663 commits)
staging: kpc2000: kpc_spi: Fix build error for {read,write}q
Staging: rtl8192e: Remove extra space before break statement
Staging: rtl8192u: ieee80211: Fix if-else indentation warning
Staging: rtl8192u: ieee80211: Fix indentation errors by removing extra spaces
staging: most: cdev: fix chrdev_region leak in mod_exit
staging: wlan-ng: Fix improper SPDX comment style
staging: rtl8192u: ieee80211: Resolve ERROR reported by checkpatch
staging: vc04_services: bcm2835-camera: Compress two lines into one line
staging: rtl8723bs: core: Use !x in place of NULL comparison.
staging: rtl8723bs: core: Prefer using the BIT Macro.
staging: fieldbus: anybus-s: fix wait_for_completion_timeout return handling
staging: kpc2000: fix up build problems with readq()
staging: rtlwifi: move remaining phydm .h files
staging: rtlwifi: strip down phydm .h files
staging: rtlwifi: delete the staging driver
staging: fieldbus: anybus-s: rename bus id field to avoid confusion
staging: fieldbus: anybus-s: keep device bus id in bus endianness
Staging: sm750fb: Change *array into *const array
staging: rtl8192u: ieee80211: Fix spelling mistake
staging: rtl8192u: ieee80211: Replace bit shifting with BIT macro
...
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
Make the forward declaration actually match the real function
definition, something that previous versions of gcc had just ignored.
This is another patch to fix new warnings from gcc-9 before I start the
merge window pulls. I don't want to miss legitimate new warnings just
because my system update brought a new compiler with new warnings.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
