In several places in the kernel we find PCI_DEVID used like this:
PCI_DEVID(dev->bus->number, dev->devfn)
Add a "pci_dev_id(struct pci_dev *dev)" helper to simplify callers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add driver for Amazon's Annapurna Labs PCIe host controller. The
controller is based on DesignWare's IP.
The controller doesn't support accessing the Root Port's config space via
ECAM, so we obtain its base address via an AMZN0001 device.
Furthermore, the DesignWare PCIe controller doesn't filter out config
transactions sent to devices 1 and up on its bus, so they are filtered by
the driver.
All subordinate buses do support ECAM access.
Implementing specific PCI config access functions involves:
- Adding an init function to obtain the Root Port's base address from
an AMZN0001 device.
- Adding a new entry in the MCFG quirk array.
[bhelgaas: Note that there is no Kconfig option for this driver because it
is only intended for use with the generic ACPI host bridge driver. This
driver is only needed because the DesignWare IP doesn't completely support
ECAM access to the root bus.]
Link: https://lore.kernel.org/lkml/1553774276-24675-1-git-send-email-jonnyc@amazon.com
Co-developed-by: Vladimir Aerov <vaerov@amazon.com>
Signed-off-by: Jonathan Chocron <jonnyc@amazon.com>
Signed-off-by: Vladimir Aerov <vaerov@amazon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
On ThinkPad P50 SKUs with an Nvidia Quadro M1000M instead of the M2000M
variant, the BIOS does not always reset the secondary Nvidia GPU during
reboot if the laptop is configured in Hybrid Graphics mode. The reason is
unknown, but the following steps and possibly a good bit of patience will
reproduce the issue:
1. Boot up the laptop normally in Hybrid Graphics mode
2. Make sure nouveau is loaded and that the GPU is awake
3. Allow the Nvidia GPU to runtime suspend itself after being idle
4. Reboot the machine, the more sudden the better (e.g. sysrq-b may help)
5. If nouveau loads up properly, reboot the machine again and go back to
step 2 until you reproduce the issue
This results in some very strange behavior: the GPU will be left in exactly
the same state it was in when the previously booted kernel started the
reboot. This has all sorts of bad side effects: for starters, this
completely breaks nouveau starting with a mysterious EVO channel failure
that happens well before we've actually used the EVO channel for anything:
nouveau 0000:01:00.0: disp: chid 0 mthd 0000 data 00000400 00001000 00000002
This causes a timeout trying to bring up the GR ctx:
nouveau 0000:01:00.0: timeout
WARNING: CPU: 0 PID: 12 at drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgf100.c:1547 gf100_grctx_generate+0x7b2/0x850 [nouveau]
Hardware name: LENOVO 20EQS64N0B/20EQS64N0B, BIOS N1EET82W (1.55 ) 12/18/2018
Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper]
...
nouveau 0000:01:00.0: gr: wait for idle timeout (en: 1, ctxsw: 0, busy: 1)
nouveau 0000:01:00.0: gr: wait for idle timeout (en: 1, ctxsw: 0, busy: 1)
nouveau 0000:01:00.0: fifo: fault 01 [WRITE] at 0000000000008000 engine 00 [GR] client 15 [HUB/SCC_NB] reason c4 [] on channel -1 [0000000000 unknown]
The GPU never manages to recover. Booting without loading nouveau causes
issues as well, since the GPU starts sending spurious interrupts that cause
other device's IRQs to get disabled by the kernel:
irq 16: nobody cared (try booting with the "irqpoll" option)
...
handlers:
[<000000007faa9e99>] i801_isr [i2c_i801]
Disabling IRQ #16
...
serio: RMI4 PS/2 pass-through port at rmi4-00.fn03
i801_smbus 0000:00:1f.4: Timeout waiting for interrupt!
i801_smbus 0000:00:1f.4: Transaction timeout
rmi4_f03 rmi4-00.fn03: rmi_f03_pt_write: Failed to write to F03 TX register (-110).
i801_smbus 0000:00:1f.4: Timeout waiting for interrupt!
i801_smbus 0000:00:1f.4: Transaction timeout
rmi4_physical rmi4-00: rmi_driver_set_irq_bits: Failed to change enabled interrupts!
This causes the touchpad and sometimes other things to get disabled.
Since this happens without nouveau, we can't fix this problem from nouveau
itself.
Add a PCI quirk for the specific P50 variant of this GPU. Make sure the
GPU is advertising NoReset- so we don't reset the GPU when the machine is
in Dedicated graphics mode (where the GPU being initialized by the BIOS is
normal and expected). Map the GPU MMIO space and read the magic 0x2240c
register, which will have bit 1 set if the device was POSTed during a
previous boot. Once we've confirmed all of this, reset the GPU and
re-disable it - bringing it back to a healthy state.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203003
Link: https://lore.kernel.org/lkml/20190212220230.1568-1-lyude@redhat.com
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: nouveau@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Ben Skeggs <skeggsb@gmail.com>
Cc: stable@vger.kernel.org
The _HPX Type 3 Setting Record is intended to be more generic and allow
configuration of settings not possible with Type 2 records. For example,
firmware could ensure that the completion timeout value is set accordingly
throughout the PCI tree.
Implement support for _HPX Type 3 Setting Records, which were added in the
ACPI 6.3 spec.
Link: https://lore.kernel.org/lkml/20190208162414.3996-4-mr.nuke.me@gmail.com
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We used to first parse all the _HPP and _HPX tables before using the
information to program registers of PCIe devices. Up through HPX Type 2,
there was only one structure of each type, so we could cheat and store it
on the stack.
With HPX Type 3 we get an arbitrary number of entries, so the above model
doesn't scale that well. Instead of parsing all tables at once, parse and
program each entry separately. For _HPP and _HPX Types 0 through 2, this
is functionally equivalent. The change enables the upcoming _HPX Type 3 to
integrate more easily.
Link: https://lore.kernel.org/lkml/20190208162414.3996-3-mr.nuke.me@gmail.com
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: fix build errors]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the bandwidth notification interrupt is left unmasked when entering
suspend to idle, it triggers immediately bringing the system back to
working state.
To keep that from happening, disable the interrupt when entering system
sleep and enable it again during resume.
Reported-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When running application tool switchtec-user's `firmware update` and `event
wait` commands concurrently, sometimes the firmware update speed reduced
significantly.
It is because when the MRPC event happened after MRPC event occurrence
check but before the event mask loop reaches its header register in event
ISR, the MRPC event would be masked unintentionally. Since there's no
chance to enable it again except for a module reload, all the following
MRPC execution completion checks time out.
Fix this bug by skipping the mask operation for MRPC event in event ISR,
same as what we already do for LINK event.
Fixes: 52eabba5bc ("switchtec: Add IOCTLs to the Switchtec driver")
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
The Switchtec devices supports two PCIe Function Frameworks (PFFs) per
upstream port (one for the port itself and one for the management endoint),
and each PFF may have up to 255 ports. Previously the driver only
supported 48 of those ports, and the SWITCHTEC_IOCTL_EVENT_SUMMARY ioctl
only returned information about those 48.
Increase SWITCHTEC_MAX_PFF_CSR from 48 to 255 so the driver supports all
255 possible ports.
Rename SWITCHTEC_IOCTL_EVENT_SUMMARY and associated struct
switchtec_ioctl_event_summary to SWITCHTEC_IOCTL_EVENT_SUMMARY_LEGACY and
switchtec_ioctl_event_summary_legacy with so existing applications work
unchanged, supporting up to 48 ports.
Add replacement SWITCHTEC_IOCTL_EVENT_SUMMARY and struct
switchtec_ioctl_event_summary that new and recompiled applications support
up to 255 ports.
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
pci_request_region_exclusive() was introduced with commit e8de1481fd
("resource: allow MMIO exclusivity for device drivers") in 2.6.29 which
was released 2008.
It never had an in tree user since then, so after 11 years later let's
remove it.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "Enhanced Allocation (EA) for Memory and I/O Resources" ECN, approved
23 October 2014, sec 6.9.1.2, specifies a second DW in the capability for
type 1 (bridge) functions to describe fixed secondary and subordinate bus
numbers. This ECN was included in the PCIe r4.0 spec, but sec 6.9.1.2 was
omitted, presumably by mistake.
Read fixed bus numbers from the EA capability for bridges.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
[bhelgaas: add pci_ea_fixed_busnrs() return value]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since the upstream MSI memory writes are generated by downstream
devices, it is logically correct to have MSI target memory coming from
the DMA pool reserved for PCIe than from the general memory pool
reserved for CPU access to avoid PCIe DMA addresses coinciding with
MSI target address thereby raising unwanted MSI interrupts.
Enforce this behaviour by retrieving the MSI address through the DMA
API.
Limit the MSI target address to 32-bits to make it work for PCIe
endpoints that support only 32-bit MSI target address; endpoints that
support 64-bit MSI target address work with 32-bit MSI target
address too.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Certain platforms like TI's AM654 do not have aseparate address space for
dbi2 instead they are accessed using the same address space as dbi
with some configuration bit set. In order to support such platforms,
add callbacks for accessing dbi2 address space.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
commit beb4641a78 ("PCI: dwc: Add MSI-X callbacks handler") while
adding MSI-X callback handler, introduced dw_pcie_ep_find_capability()
and __dw_pcie_ep_find_next_cap() for finding the MSI and MSIX capability.
However if MSI or MSIX capability is the last capability (i.e there are
no additional items in the capabilities list and the Next Capability
Pointer is set to '0'), __dw_pcie_ep_find_next_cap will return '0'
even though MSI or MSIX capability may be present because of
incorrect ordering of the "next_cap_ptr" check. Fix it.
Fixes: beb4641a78 ("PCI: dwc: Add MSI-X callbacks handler")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add const qualifier to struct dw_pcie_ep_ops member of
struct dw_pcie_ep.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The address that is allocated using pci_epf_alloc_space() is
directly written to the target address of the Inbound Address
Translation unit (ie the HW component implementing inbound address
decoding) on endpoint controllers.
Designware IP [1] has a configuration parameter (CX_ATU_MIN_REGION_SIZE
[2]) which has 64KB as default value and the lower 16 bits of the Base,
Limit and Target registers of the Inbound ATU are fixed to zero. If the
programmed memory address is not aligned to 64 KB boundary this causes
memory corruption.
Modify pci_epf_alloc_space() API to take alignment size as argument in
order to allocate buffers to be mapped to BARs with an alignment that
suits the platform where they are used.
Add an 'align' parameter to epc_features which can be used by platform
drivers to specify the BAR allocation alignment requirements and use
this while invoking pci_epf_alloc_space().
[1] "I/O and MEM Match Modes" section in DesignWare Cores PCI Express
Controller Databook version 4.90a
[2] http://www.ti.com/lit/ug/spruid7c/spruid7c.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
PCIe in TI's AM654 devices is by default configured to work in GEN3 mode.
However PCIe does not work reliably in GEN3 mode because of SERDES
configuration.
Add support to set the link speed to GEN1, GEN2 or GEN3 based on
"max-link-speed" DT property with GEN2 as the default speed if
"max-link-speed" is absent.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
of_pci_get_max_link_speed() is built only if CONFIG_PCI is enabled.
Make of_pci_get_max_link_speed() to be also used by PCI Endpoint
controllers with just CONFIG_PCI_ENDPOINT enabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
SERDES connected to the PCIe controller in AM654 requires
power on reset enable (POR_EN) to be set in the SERDES. The
SERDES driver sets POR_EN in the reset ops and it has to be
invoked before init or enable ops. In order for SERDES driver
to set POR_EN, invoke the phy_reset() API in pci-keystone driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add PCIe RC support for AM654x Platforms in pci-keystone.c
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
hook_fault_code() is an ARM32 specific API for hooking into data abort.
AM65X platforms (that integrate ARM v8 cores and select CONFIG_ARM64 as
arch) rely on pci-keystone.c but on them the enumeration of a
non-present BDF does not trigger a bus error, so the fixup exception
provided by calling hook_fault_code() is not needed and can be guarded
with CONFIG_ARM.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Synopsys designware version >= 4.80 uses a separate register space
for programming ATU. The current code identifies if there exists a
separate register space by accessing the register address of ATUs
in designware version < 4.80. Accessing this address results in
abort in the case of K2G.
Fix it here by adding "version" member to struct dw_pcie. This should be
set by platform specific drivers and designware core will use it to
identify if the platform has a separate ATU space. For platforms which
have not populated the version member, the old method of identification
will still be used.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
iatu_unroll_enabled flag is set only for Designware in host mode.
However iATU unroll can be applicable for endpoint mode too. Set
iatu_unroll_enabled flag in dw_pcie_setup() which is common for
both host mode and endpoint mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Explicitly set the PCIe mode to BOOTCFG_DEVCFG instead of always
relying on the default values. This is required when EP mode has to
be explicitly written to BOOTCFG_DEVCFG register.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Move platform_get_resource() calls for resources that are applicable to
both host and endpoint mode (ie "dbics" and "app") from
ks_add_pcie_port() to the probe() callback, in preparation for adding
endpoint support to pci-keystone driver.
No functional change intended.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Currently the bitwise operations on the u16 variable 'status' with
the setting ROCKCHIP_PCIE_EP_CMD_STATUS_IS are incorrect because
ROCKCHIP_PCIE_EP_CMD_STATUS_IS is 1UL<<19 which is wider than the
u16 variable.
Fix this by making status a u32.
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Fix spelling errors and format function comments consistently. Changes
whitespace and comments only; no functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
In most cases, kmalloc() will not be available early in boot when
pci_setup() is called. Thus, the kstrdup() call that was added to fix the
__initdata bug with the disable_acs_redir parameter usually returns NULL,
so the parameter is discarded and has no effect.
To fix this, store the string that's in initdata until an initcall function
can allocate the memory appropriately. This way we don't need any
additional static memory.
Fixes: d2fd6e8191 ("PCI: Fix __initdata issue with "pci=disable_acs_redir" parameter")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In case alloc_workqueue() fails, return -ENOMEM to avoid
potential NULL pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
[lorenzo.pieralisi@arm.com: commit log and code update]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Set the "untrusted" attribute to any PCIe port that has an
"external-facing" device tree property. Any device downstream of this port
will inherit the attribute and have only the strictest IOMMU protection.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ATS is broken on the Radeon R7 GPU (at least for Stoney Ridge based laptop)
and causes IOMMU stalls and system failure. Disable ATS on these devices
to make them usable again with IOMMU enabled.
Thanks to Joerg Roedel <jroedel@suse.de> for help.
[bhelgaas: In the email thread mentioned below, Alex suspects the real
problem is in sbios or iommu, so it may affect only certain systems, and it
may affect other devices in those systems as well. However, per Joerg we
lack the ability to debug further, so this quirk is the best we can do for
now.]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194521
Link: https://lore.kernel.org/lkml/20190408103725.30426-1-nickel@altlinux.org
Fixes: 9b44b0b09d ("PCI: Mark AMD Stoney GPU ATS as broken")
Signed-off-by: Nikolai Kostrigin <nickel@altlinux.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
CC: stable@vger.kernel.org
Use platform_get_resource_byname() instead of platform_get_resource()
which uses an index to get memory resources. While at that get the memory
resource defined specifically for configuration space instead of
deriving the configuration space address from dbics address space.
Since the pci-keystone driver has never worked in the mainline kernel,
DT backward compatibility is not an issue.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
No functional change. Instead of having two functions
ks_pcie_add_pcie_port() and ks_pcie_dw_host_init() for initializing
host, have a single function to perform all the host initialization.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pci-keystone driver uses irq_of_parse_and_map() to get irq number of
error_irq.
Use platform_get_irq() instead and move platform_get_irq() and
request_irq() of error_irq from ks_pcie_add_pcie_port to ks_pcie_probe
since error_irq is common to both RC mode and EP mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add start_link()/stop_link() dw_pcie_ops and invoke ks_pcie_start_link()
directly from host_init. start_link()/stop_link() ops are required for
adding EP mode support.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
When allocating the slot structure we store a pointer to the associated
device_node. We really should be incrementing the reference count, so add
an of_node_get() during slot alloc and an of_node_put() during slot
dealloc.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The find_dlpar_node() helper returns a device node with its reference
incremented. Both the add and remove paths use this helper for find the
appropriate node, but fail to release the reference when done.
Annotate the find_dlpar_node() helper with a comment about the incremented
reference count and call of_node_put() on the obtained device_node in the
add and remove paths. Also, fixup a reference leak in the find_vio_slot()
helper where we fail to call of_node_put() on the vdevice node after we
iterate over its children.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
During a safe hot remove, the OS powers off the slot, which may cause a
Data Link Layer State Changed event. The slot has already been set to
OFF_STATE, so that event results in re-enabling the device, making it
impossible to safely remove it.
Clear out the Presence Detect Changed and Data Link Layer State Changed
events when the disabled slot has settled down.
It is still possible to re-enable the device if it remains in the slot
after pressing the Attention Button by pressing it again.
Fixes the problem that Micah reported below: an NVMe drive power button may
not actually turn off the drive.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203237
Reported-by: Micah Parrish <micah.parrish@hpe.com>
Tested-by: Micah Parrish <micah.parrish@hpe.com>
Signed-off-by: Sergey Miroshnichenko <s.miroshnichenko@yadro.com>
[bhelgaas: changelog, add bugzilla URL]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.19+
