Enables the FSL EDMA driver by default. This also works around an issue
that imx-i2c driver keeps deferring the probe because of the DMA is not
ready. And currently the DMA engine framework can not correctly tell
if the DMA channels will truly become available later (it will never be
available if the DMA driver is not enabled).
This will cause indefinite messages like below:
[ 3.335829] imx-i2c 2180000.i2c: can't get pinctrl, bus recovery not supported
[ 3.344455] ina2xx 0-0040: power monitor ina220 (Rshunt = 1000 uOhm)
[ 3.350917] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator
[ 3.362089] imx-i2c 2180000.i2c: can't get pinctrl, bus recovery not supported
[ 3.370741] ina2xx 0-0040: power monitor ina220 (Rshunt = 1000 uOhm)
[ 3.377205] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator
[ 3.388455] imx-i2c 2180000.i2c: can't get pinctrl, bus recovery not supported
.....
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The QCS404 has a PCIe2 PHY and a Qualcomm PCIe controller, define these
to for the platform.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix ssbd.c which depends implicitly on asm/ptrace.h including
linux/prctl.h (through for example linux/compat.h, then linux/time.h,
linux/seqlock.h, linux/spinlock.h and linux/irqflags.h), and uses
PR_SPEC* defines.
This is an issue since we'll soon be removing the include from
asm/ptrace.h.
Fixes: 9cdc0108ba ("arm64: ssbd: Add prctl interface for per-thread mitigation")
Cc: stable@vger.kernel.org
Signed-off-by: Anisse Astier <aastier@freebox.fr>
Signed-off-by: Will Deacon <will.deacon@arm.com>
AM654 base board does not have any PCIe slots. Disable all the
SERDES and PCIe instances.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add mux-controller DT node as a child node of scm_conf. This is
required for muxing SERDES between USB, PCIe and ICSS2 SGMII.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
GIC_ITS used in AM654 platform has the same configuration as that of
GIC_ITS used in Socionext SoCs. Add "socionext,synquacer-pre-its"
property to get PCI MSI working.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the MSCM RAM address space to the ranges property of the cbass_main
interconnect node so that the addresses can be translated properly.
This fixes the probe failure in the sram driver for the MSMC RAM node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the address spaces for the R5F cores in MCU domain to the ranges
property of the cbass_mcu interconnect node so that the addresses
within the R5F nodes can be translated properly by the relevant OF
address API.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the on-chip SRAM present within the MCU domain as a mmio-sram node.
The K3 AM65x SoCs have 512 KB of such memory. Any specific memory range
within this RAM needed by a software module ought to be reserved using
an appropriate child node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the address space for the MCU SRAM memory to the ranges property
of the cbass_mcu interconnect node so that the addresses within the
mcu_sram nodes and its children can be translated properly by the
relevant OF address API.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There are 2 push buttons: SW5 and SW6 that are basically connected to
WKUP_GPIO0_24 and WKUP_GPIO0_27 respectively. Add the respective
nodes and the pinctrl data to set the mode to GPIO and Input.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add gpio0/1 nodes under main domain. They have 96 and 90 gpios
respectively and all are capable of generating banked interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add gpio0 node under wakeup domain. This has 56 gpios
and all are capable of generating banked interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Wakeup domain in AM654 SoC has an interrupt router connected to gpio
in wakeup domain. Add DT node for this interrupt router.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Main domain in AM654 has the following interrupt controller instances:
- Main Domain GPIO Interrupt router connected to gpio in main domain.
- Under the Main Domain Navigator Subsystem(NAVSS)
- Main Navss Interrupt Router connected to main navss inta and mailboxes.
- Main Navss Interrupt Aggregator connected to main domain UDMASS
Add DT nodes for the above three interrupt controllers available
in main domain.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Use the am654 specific compatible for dmsc. This allows to use
the am654 specific RM mapping table.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This pull request contains Broadcom ARM64-based SoCs Kconfig.platform
changes for 5.3, please pull the following:
- Jim adds the ability for ARCH_BRCMSTB to use reset controllers
- Doug adds the ability for ARCH_BRCMSTB to use the PINCTRL framework
- Florian enables the use of the BCM7038 Level 1 interrupt controller
for ARCH_BRCMSTB
* tag 'arm-soc/for-5.3/soc-arm64' of https://github.com/Broadcom/stblinux:
arm64: Enable PINCTRL for ARCH_BRCMSTB
arm64: Enable ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB
arm64: Enable BCM7038_L1_IRQ for ARCH_BRCMSTB
Signed-off-by: Olof Johansson <olof@lixom.net>
If the cache line size is greater than ARCH_DMA_MINALIGN (128),
the warning shows and it's tainted as TAINT_CPU_OUT_OF_SPEC.
However, it's not good because as discussed in the thread [1], the cpu
cache line size will be problem only on non-coherent devices.
Since the coherent flag is already introduced to struct device,
show the warning only if the device is non-coherent device and
ARCH_DMA_MINALIGN is smaller than the cpu cache size.
[1] https://lore.kernel.org/linux-arm-kernel/20180514145703.celnlobzn3uh5tc2@localhost/
Signed-off-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Tested-by: Zhang Lei <zhang.lei@jp.fujitsu.com>
[catalin.marinas@arm.com: removed 'if' block for WARN_TAINT]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Similarly to what done for the r8a7796 with commit 737e05bf03
("arm64: dts: renesas: revise properties for R-Car Gen3 SoCs'
usb 2.0"), this patch lists the clock for the USB High-Speed Module
(HS-USB) with the USB2.0 Host (EHCI/OHCI) IP DT node, and it lists
the clock for the USB2.0 Host IP with the HS-USB module DT node.
Fixes: 4c2c2fb998 ("arm64: dts: renesas: r8a774a1: Add USB2.0 phy and host(EHCI/OHCI) device nodes")
Fixes: ed898d4fc1 ("arm64: dts: renesas: r8a774a1: Add USB-DMAC and HSUSB device nodes")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Texas Instruments AM65x fixes for v5.2
- Fix up a Kbuild warning when SOC_TI is not set
* tag 'am654-fixes-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: arch_k3: Fix kconfig dependency warning
Signed-off-by: Olof Johansson <olof@lixom.net>
i.MX fixes for 5.2:
- A build fix for soc-imx8 driver which needs SOC_BUS support. To
avoid dealing with the dependency for every single i.MX SoC bus
driver, we selects at from architecture level.
- A fix on i.MX SCU firmware driver to ensure SCU irq is enabled only
after IPC is ready.
- A regression fix on cpuidle-imx6sx driver, which causes some
characters loss on serial communication.
* tag 'imx-fixes-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: cpuidle-imx6sx: Restrict the SW2ISO increase to i.MX6SX
firmware: imx: SCU irq should ONLY be enabled after SCU IPC is ready
arm64: imx: Fix build error without CONFIG_SOC_BUS
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch is to add ptp timer device tree node for dpaa2
platforms(ls1088a/ls208xa/lx2160a).
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the sound card on the X96 Max, enabling HDMI output using the
TDM interface B, being aligned on other boards sound cards.
SPDI/F support is also enabled to the physical toslink port and to HDMI.
The internal DAC connected to the audio jack will be added later on, when
driver support is added.
Tested by running:
tinymix set "FRDDR_A SRC 1 EN Switch" 1
tinymix set "FRDDR_A SINK 1 SEL" "OUT 1"
tinymix set "FRDDR_B SRC 1 EN Switch" 1
tinymix set "FRDDR_B SINK 1 SEL" "OUT 1"
tinymix set "FRDDR_C SRC 1 EN Switch" 1
tinymix set "FRDDR_C SINK 1 SEL" "OUT 1"
tinymix set "TOHDMITX I2S SRC" "I2S B"
tinymix set "TOHDMITX Switch" 1
then:
tinymix set "TDMOUT_B SRC SEL" "IN 0"
speaker-test -Dhw:0,0 -c2
then:
tinymix set "TDMOUT_B SRC SEL" "IN 1"
speaker-test -Dhw:0,1 -c2
then:
tinymix set "TDMOUT_B SRC SEL" "IN 2"
speaker-test -Dhw:0,2 -c2
testing HDMI audio output from the all 3 ASoC playback interfaces.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the sound card on the Hardkernel Odroid-N2, enabling HDMI output
using the TDM interface B, being aligned on other boards sound cards.
The internal DAC connected to the audio jack will be added later on, when
driver support is added.
Tested by running:
tinymix set "FRDDR_A SRC 1 EN Switch" 1
tinymix set "FRDDR_A SINK 1 SEL" "OUT 1"
tinymix set "FRDDR_B SRC 1 EN Switch" 1
tinymix set "FRDDR_B SINK 1 SEL" "OUT 1"
tinymix set "FRDDR_C SRC 1 EN Switch" 1
tinymix set "FRDDR_C SINK 1 SEL" "OUT 1"
tinymix set "TOHDMITX I2S SRC" "I2S B"
tinymix set "TOHDMITX Switch" 1
then:
tinymix set "TDMOUT_B SRC SEL" "IN 0"
speaker-test -Dhw:0,0 -c2
then:
tinymix set "TDMOUT_B SRC SEL" "IN 1"
speaker-test -Dhw:0,1 -c2
then:
tinymix set "TDMOUT_B SRC SEL" "IN 2"
speaker-test -Dhw:0,2 -c2
testing HDMI audio output from the all 3 ASoC playback interfaces.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the sound card on the sei510:
* TDM interface A is connected to an external DAC and a speaker installed
on the device.
* HDMI is expected to use TDM B. It can also use TDM A but will be
limited to 2 channels, as accepted by the external DAC.
* 2 Built in PDM mics through the PDM interface.
* Both TDM outputs may use HW loopback.
The internal DAC connected to audio jack will be added later on, when
driver support is added.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Convert kdump documentation to ReST and add it to the
user faced manual, as the documents are mainly focused on
sysadmins that would be enabling kdump.
Note: the vmcoreinfo.rst has one very long title on one of its
sub-sections:
PG_lru|PG_private|PG_swapcache|PG_swapbacked|PG_slab|PG_hwpoision|PG_head_mask|PAGE_BUDDY_MAPCOUNT_VALUE(~PG_buddy)|PAGE_OFFLINE_MAPCOUNT_VALUE(~PG_offline)
I opted to break this one, into two entries with the same content,
in order to make it easier to display after being parsed in html and PDF.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The documentation is in a format that is very close to ReST format.
The conversion is actually:
- add blank lines in order to identify paragraphs;
- fixing tables markups;
- adding some lists markups;
- marking literal blocks;
- adjust some title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Pull arm64 fixes from Will Deacon:
"Here are some arm64 fixes for -rc5.
The only non-trivial change (in terms of the diffstat) is fixing our
SVE ptrace API for big-endian machines, but the majority of this is
actually the addition of much-needed comments and updates to the
documentation to try to avoid this mess biting us again in future.
There are still a couple of small things on the horizon, but nothing
major at this point.
Summary:
- Fix broken SVE ptrace API when running in a big-endian configuration
- Fix performance regression due to off-by-one in TLBI range checking
- Fix build regression when using Clang"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/sve: Fix missing SVE/FPSIMD endianness conversions
arm64: tlbflush: Ensure start/end of address range are aligned to stride
arm64: Don't unconditionally add -Wno-psabi to KBUILD_CFLAGS
Tegra186 board under arm64 is using this device, according to
its dts file. So this patch enables its driver with a "=m" as
the other HWMON drivers.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Due to an integration issue the architected timer on Tegra210 does not
remain on during system suspend (a.k.a. SC7). Mark it accordingly so
that it isn't considered as a means to track suspend time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The architected timer on Tegra186 and Tegra194 is in an always on power
partition and its reference clock will always run, so mark the timer as
always on.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add devicetree support for Khadas Edge/Edge-V/Captain boards.
Khadas Edge is an expandable Rockchip RK3399 board with goldfinger.
Khadas Captain is the carrier board for Khadas Edge.
Khadas Edge-V is a Khadas VIM form factor Rockchip RK3399 board.
Signed-off-by: Nick Xie <nick@khadas.com>
[edge-captain and edge-v contain different components that are supposed
to get added in future patches, so should stay separate while looking
somewhat similar right now]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This commit enables the hdmi-sound device needed to have
audio over HDMI on the Rock Pi board.
Fixes: 1b5715c602 ("arm64: dts: rockchip: add ROCK Pi 4 DTS support")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The in-memory representation of SVE and FPSIMD registers is
different: the FPSIMD V-registers are stored as single 128-bit
host-endian values, whereas SVE registers are stored in an
endianness-invariant byte order.
This means that the two representations differ when running on a
big-endian host. But we blindly copy data from one representation
to another when converting between the two, resulting in the
register contents being unintentionally byteswapped in certain
situations. Currently this can be triggered by the first SVE
instruction after a syscall, for example (though the potential
trigger points may vary in future).
So, fix the conversion functions fpsimd_to_sve(), sve_to_fpsimd()
and sve_sync_from_fpsimd_zeropad() to swab where appropriate.
There is no common swahl128() or swab128() that we could use here.
Maybe it would be worth making this generic, but for now add a
simple local hack.
Since the byte order differences are exposed in ABI, also clarify
the documentation.
Cc: Alex Bennée <alex.bennee@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Alan Hayward <alan.hayward@arm.com>
Cc: Julien Grall <julien.grall@arm.com>
Fixes: bc0ee47603 ("arm64/sve: Core task context handling")
Fixes: 8cd969d28f ("arm64/sve: Signal handling support")
Fixes: 43d4da2c45 ("arm64/sve: ptrace and ELF coredump support")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
[will: Fix typos in comments and docs spotted by Julien]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Constify the ctx and iv arguments to crypto_chacha_init() and the
various chacha*_stream_xor() functions. This makes it clear that they
are not modified.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since commit 3d65b6bbc0 ("arm64: tlbi: Set MAX_TLBI_OPS to
PTRS_PER_PTE"), we resort to per-ASID invalidation when attempting to
perform more than PTRS_PER_PTE invalidation instructions in a single
call to __flush_tlb_range(). Whilst this is beneficial, the mmu_gather
code does not ensure that the end address of the range is rounded-up
to the stride when freeing intermediate page tables in pXX_free_tlb(),
which defeats our range checking.
Align the bounds passed into __flush_tlb_range().
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Reported-by: Hanjun Guo <guohanjun@huawei.com>
Tested-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
