ca0132 codec driver loads the firmware selectively depending on the
model in addition to the fallback of the default firmware. The code
works good, but a minor problem is that the current code seems
confusing for Clang where it spews a warning about uninitialized
variable.
This patch simplifies the code flow for such a false-positive
warning. After this refactoring, the ca0132_spec.alt_firmware_present
field is no longer used, hence it's eliminated as well.
Reported-and-tested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Changing the VLAN header may be implemented by pop the existing header
and push a new one. Translate those operations as VLAN modify.
Applicable for use cases such as OVS where the controller translates a
vlan modify meta (OF) rule to DP pop+push actions rule.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Support VLAN modify action by emulating a rewrite action for the VLAN
fields. Currently, the only supported field is the vid. The prio in the
action must be set to 0 to indicate no change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently support only default geneve udp port (6081).
For the tx side, the HW is assisted by SW parsing, which sets the
headers offset to offload tunneled LSO and csum. Note that for udp
tunnels, we don't use special rx offloads, as rss on the outer headers
is enough, we support checksum complete and GRO takes care of
aggregation.
Geneve TSO BW and CPU load results (tested using iperf single tcp
stream).
In this patch we add TSO support over Geneve, so the "before" result
doesn't actually get to using the TSO HW offload even when turned on.
Tested on ConnectX-5, Intel(R) Xeon(R) CPU E5-2660 v2 @2.20GHz.
__________________________________
| Before | After |
|________________|_________________|
| 12.6 Gbits/sec | 21.7 Gbits/sec |
| 100% CPU load | 61.5% CPU load |
|________________|_________________|
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Refactor mlx5e_ipsec_set_swp() code, split the part which sets the eseg
software parser (SWP) offsets and flags, so it can be used in a
downstream patch by other mlx5e functionality which needs to set eseg
SWP.
The new function mlx5e_set_eseg_swp() is useful for setting swp for both
outer and inner headers. It also handles the special ipsec case of xfrm
mode transfer.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Amazingly a mlx5e_tc function is being called from the eswitch layer,
which is by itself very terrible! The function was declared locally in
eswitch_offloads.c so it could be used there, which caused the following
compilation warning, fix that.
drivers/.../mlx5/core/en_tc.c:3242:6: [-Werror=missing-prototypes]
error: no previous prototype for ‘mlx5e_tc_clean_fdb_peer_flows’
Fixes: 04de7dda73 ("net/mlx5e: Infrastructure for duplicated offloading of TC flows")
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch fixes compiler warnings:
In drivers/.../mlx5/core/en/port_buffer.c:190:
warning: Function parameter or member 'pfc_en' not described...
...
warning: Function parameter or member 'change' not described...
Fixes: 0696d60853 ("net/mlx5e: Receive buffer configuration")
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5_eq_table_get_rmap is being used only when CONFIG_RFS_ACCEL is
enabled, this patch fixes the below warning when CONFIG_RFS_ACCEL is
disabled.
drivers/.../mlx5/core/eq.c:903:18: [-Werror=missing-prototypes]
error: no previous prototype for ‘mlx5_eq_table_get_rmap’
Fixes: f2f3df5501 ("net/mlx5: EQ, Privatize eq_table and friends")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
It is desired to get rid of num_vfs stored inside mlx5_core_sriov to
safely support vports more than vfs.
To reduce dependency on mlx5_core_sriov num_vfs, start using
pci_num_vf() from pci core.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Macro MLX5_TOTAL_VPORTS() returns total number of vports. Therefore,
rename variable total_vfs to total_vports to improve code readability.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Simplify sriov enable/disable flow for below two checks.
1. PCI core driver allows sriov configuration only on a PF.
This is done in drivers/pci/pci-sysfs.c sriov_attrs_are_visible().
2. PCI core driver allow sriov enablement if the sriov is currently
disabled for for a PF. This is done in drivers/pci/pci-sysfs.c
sriov_numvfs_store().
Hence there is no need for mlx5 driver to duplicate such checks.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull device properties framework fix from Rafael Wysocki:
"Add missing 'static' in two places (YueHaibing)"
* tag 'devprop-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
drivers: base: swnode: Make two functions static
Pull ACPI fix from Rafael Wysocki:
"Prevent device references acquired by bus_find_device() in
acpi_dev_present() from being leaked (Andy Shevchenko)"
* tag 'acpi-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / utils: Drop reference in test for device presence
Pull power management fixes from Rafael Wysocki:
"These rearrange some code in the generic power domains (genpd)
framework to avoid a potential deadlock and make the turbostat utility
behave more as expected.
Specifics:
- Rearrange the generic power domains (genpd) code to avoid a
potential deadlock possible due to its interactions with the clock
framework (Jiada Wang)
- Make turbostat return the exit status of the command run under it
if that command fails (David Arcari)"
* tag 'pm-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Domains: Avoid a potential deadlock
tools/power turbostat: return the exit status of a command
Pull MMC fixes from Ulf Hansson:
"A couple of MMC host fixes intended for v5.1:
- alcor: Fix DMA reads
- renesas_sdhi: Limit block count to 16-bit for old revisions
- sdhci-omap: Fixup support for read-only pins
- mxcmmc: Revert support for highmem pages
- davinci/pxamci: Fix clang build warnings"
* tag 'mmc-v5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: renesas_sdhi: limit block count to 16 bit for old revisions
mmc: alcor: fix DMA reads
mmc: sdhci-omap: Set caps2 to indicate no physical write protect pin
mmc: mxcmmc: "Revert mmc: mxcmmc: handle highmem pages"
mmc: davinci: remove extraneous __init annotation
mmc: pxamci: fix enum type confusion
Commit 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect
change or polling state is detected") was intended to prevent ports that
were still link training from being forced to U3 suspend state mid
enumeration.
This solved enumeration issues for devices with slow link training.
Turns out some devices are stuck in the link training/polling state,
and thus that patch will prevent suspend completely for these devices.
This is seen with USB3 card readers in some MacBooks.
Instead of preventing suspend, give some time to complete the link
training. On successful training the port will end up as connected
and enabled.
If port instead is stuck in link training the bus suspend will continue
suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout).
Original patch was sent to stable, this one should go there as well
Fixes: 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci debug capability (DbC) feature did its memory cleanup with
spinlock held. dma_free_coherent() warns if called with interrupts
disabled
move the memory cleanup outside the spinlock
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A suspended SS port in U3 link state will go to U0 when resumed, but
can almost immediately after that enter U1 or U2 link power save
states before host controller driver reads the port status.
Host controller driver only checks for U0 state, and might miss
the finished resume, leaving flags unclear and skip notifying usb
code of the wake.
Add U1 and U2 to the possible link states when checking for finished
port resume.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
spdxcheck.py complains:
include/linux/platform_data/gpio/gpio-amd-fch.h: 1:28 Invalid License ID: GPL+
which is correct because GPL+ is not a valid identifier. Of course this
could have been caught by checkpatch.pl _before_ submitting or merging the
patch.
WARNING: 'SPDX-License-Identifier: GPL+ */' is not supported in LICENSES/...
#271: FILE: include/linux/platform_data/gpio/gpio-amd-fch.h:1:
+/* SPDX-License-Identifier: GPL+ */
Fix it under the assumption that the author meant GPL-2.0+, which makes
sense as the corresponding C file is using that identifier.
Fixes: e09d168f13 ("gpio: AMD G-Series PCH gpio driver")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Current code test wrong value so it does not verify if the written
data is correctly read back. Fix it.
Also make it return -EPERM if read value does not match written bit,
just like it done for adnp_gpio_direction_output().
Fixes: 5e969a401a ("gpio: Add Avionic Design N-bit GPIO expander support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
ida_simple_get may fail and return a negative error number.
The fix checks its return value; if it fails, go to err_destroy.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The PCM OSS emulation converts and transfers the data on the fly via
"plugins". The data is converted over the dynamically allocated
buffer for each plugin, and recently syzkaller caught OOB in this
flow.
Although the bisection by syzbot pointed out to the commit
65766ee0bf ("ALSA: oss: Use kvzalloc() for local buffer
allocations"), this is merely a commit to replace vmalloc() with
kvmalloc(), hence it can't be the cause. The further debug action
revealed that this happens in the case where a slave PCM doesn't
support only the stereo channels while the OSS stream is set up for a
mono channel. Below is a brief explanation:
At each OSS parameter change, the driver sets up the PCM hw_params
again in snd_pcm_oss_change_params_lock(). This is also the place
where plugins are created and local buffers are allocated. The
problem is that the plugins are created before the final hw_params is
determined. Namely, two snd_pcm_hw_param_near() calls for setting the
period size and periods may influence on the final result of channels,
rates, etc, too, while the current code has already created plugins
beforehand with the premature values. So, the plugin believes that
channels=1, while the actual I/O is with channels=2, which makes the
driver reading/writing over the allocated buffer size.
The fix is simply to move the plugin allocation code after the final
hw_params call.
Reported-by: syzbot+d4503ae45b65c5bc1194@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes how we get VF VSIs instances. Instead of relying on
mailbox virtual channel message to retrieve VSI, it is more reliable
getting it directly via VF object in PF data structure.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When VF requested for queues changes, we need to update LAN Tx queue with
correct number of VF queue pairs and re-allocate VF resources based on
this new requested number of queues, which is constraint within maximum
queue supported per VF.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 7c710869d6 ("ice: Add handlers for VF netdevice operations")
seems to have inadvertently introduced a function prototype for
ice_set_vf_bw that isn't implemented. Remove it.
Fixes: 7c710869d6 ("ice: Add handlers for VF netdevice operations")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes issue reclaiming VF resources back to the pool after
reset - Since we only allocate HW vector for all VFs and track together
with resources allocation for PF with ice_search_res, we need to free VFs
resources separately, using first VF vector index to traverse the list.
Otherwise tracker starts from the last assigned vectors list and causes
maximum supported number of HW vectors, 1024 to be exhausted, depending on
the number of VFs enabled, which causes a lot of unwanted issues, and
failed to reassign vectors for VFs.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since maxattr is common, the policy can't really differ sanely,
so make it common as well.
The only user that did in fact manage to make a non-common policy
is taskstats, which has to be really careful about it (since it's
still using a common maxattr!). This is no longer supported, but
we can fake it using pre_doit.
This reduces the size of e.g. nl80211.o (which has lots of commands):
text data bss dec hex filename
398745 14323 2240 415308 6564c net/wireless/nl80211.o (before)
397913 14331 2240 414484 65314 net/wireless/nl80211.o (after)
--------------------------------
-832 +8 0 -824
Which is obviously just 8 bytes for each command, and an added 8
bytes for the new policy pointer. I'm not sure why the ops list is
counted as .text though.
Most of the code transformations were done using the following spatch:
@ops@
identifier OPS;
expression POLICY;
@@
struct genl_ops OPS[] = {
...,
{
- .policy = POLICY,
},
...
};
@@
identifier ops.OPS;
expression ops.POLICY;
identifier fam;
expression M;
@@
struct genl_family fam = {
.ops = OPS,
.maxattr = M,
+ .policy = POLICY,
...
};
This also gets rid of devlink_nl_cmd_region_read_dumpit() accessing
the cb->data as ops, which we want to change in a later genl patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the call to netif_wake_queue in rtl8169_start_xmit with
netif_start_queue as we don't need to actually wake up the queue since
we are still in mid transmit so we just need to reset the bit so it
doesn't prevent the next transmit.
(Description shamelessly copied from a mail sent by Alex.)
Suggested-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aquantia PHY's of the AQR107 family support the downshift feature.
Add support for it as standard PHY tunable so that it can be controlled
via ethtool.
The AQCS109 supports a proprietary 2-pair 1Gbps mode. If two such PHY's
are connected to each other with a 2-pair cable, they may not be able
to establish a link if both advertise modes > 1Gbps.
v2:
- add downshift event detection
- warn if downshift occurred
- read downshifted rate from vendor register
- enable downshift per default on all AQR107 family members
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_IOMMU_API isn't set the following warnings pops up:
drivers/gpu/drm/tegra/vic.c: In function ‘vic_boot’:
drivers/gpu/drm/tegra/vic.c:110:31: error: implicit declaration of function ‘dev_iommu_fwspec_get’; did you mean ‘iommu_fwspec_free’? [-Werror=implicit-function-declaration]
struct iommu_fwspec *spec = dev_iommu_fwspec_get(vic->dev);
^~~~~~~~~~~~~~~~~~~~
iommu_fwspec_free
drivers/gpu/drm/tegra/vic.c:110:31: warning: initialization of ‘struct iommu_fwspec *’ from ‘int’ makes pointer from integer without a cast [-Wint-conversion]
drivers/gpu/drm/tegra/vic.c:117:19: error: ‘struct iommu_fwspec’ has no member named ‘num_ids’
if (spec && spec->num_ids > 0) {
^~
drivers/gpu/drm/tegra/vic.c:118:16: error: ‘struct iommu_fwspec’ has no member named ‘ids’
value = spec->ids[0] & 0xffff;
^~
Rework so that its inside a '#ifdef CONFIG_IOMMU_API' block.
Fixes: f3779cb190 ("drm/tegra: vic: Support stream ID register programming")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
