commit b2d2d7ea0dd09802cf5a0545bf54d8ad8987d20c upstream.
When write UDC to empty and unbind gadget driver from gadget device, it is
possible that there are many queue failures for mass storage function.
The root cause is mass storage main thread alaways try to queue request to
receive a command from host if running flag is on, on platform like dwc3,
if pull down called, it will not queue request again and return
-ESHUTDOWN, but it not affect running flag of mass storage function.
Check return code from mass storage function and clear running flag if it
is -ESHUTDOWN, also indicate start in/out transfer failure to break loops.
Cc: stable <stable@kernel.org>
Signed-off-by: yuan linyu <yuanlinyu@hihonor.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240123034829.3848409-1-yuanlinyu@hihonor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f17c34ffc792bbb520e4b61baa16b6cfc7d44b13 upstream.
The OTG 1.3 spec has the feature A_ALT_HNP_SUPPORT, which tells
a device that it is connected to the wrong port. Some devices
refuse to operate if you enable that feature, because it indicates
to them that they ought to request to be connected to another port.
According to the spec this feature may be used based only the following
three conditions:
6.5.3 a_alt_hnp_support
Setting this feature indicates to the B-device that it is connected to
an A-device port that is not capable of HNP, but that the A-device does
have an alternate port that is capable of HNP.
The A-device is required to set this feature under the following conditions:
• the A-device has multiple receptacles
• the A-device port that connects to the B-device does not support HNP
• the A-device has another port that does support HNP
A check for the third and first condition is missing. Add it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Fixes: 7d2d641c44 ("usb: otg: don't set a_alt_hnp_support feature for OTG 2.0 device")
Link: https://lore.kernel.org/r/20240122153545.12284-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2840143e393a4ddc1caab4372969ea337371168c upstream.
In case of a spurious or otherwise delayed notification it is
possible that CCI still reports the previous completion. The
UCSI spec is aware of this and provides two completion bits in
CCI, one for normal commands and one for acks. As acks and commands
alternate the notification handler can determine if the completion
bit is from the current command.
The initial UCSI code correctly handled this but the distinction
between the two completion bits was lost with the introduction of
the new API.
To fix this revive the ACK_PENDING bit for ucsi_acpi and only complete
commands if the completion bit matches.
Fixes: f56de278e8 ("usb: typec: ucsi: acpi: Move to the new API")
Cc: stable@vger.kernel.org
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 520b391e3e813c1dd142d1eebb3ccfa6d08c3995 upstream.
Upstream commit bac1ec551434 ("usb: xhci: Set quirk for
XHCI_SG_TRB_CACHE_SIZE_QUIRK") introduced a new quirk in XHCI
which fixes XHC timeout, which was seen on synopsys XHCs while
using SG buffers. Currently this quirk can only be set using
xhci private data. But there are some drivers like dwc3/host.c
which adds adds quirks using software node for xhci device.
Hence set this xhci quirk by iterating over device properties.
Cc: stable@vger.kernel.org # 5.11
Fixes: bac1ec551434 ("usb: xhci: Set quirk for XHCI_SG_TRB_CACHE_SIZE_QUIRK")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20240116055816.1169821-3-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12b17b4eb82a41977eb848048137b5908d52845c upstream.
The device IMST USB-Stick for Smart Meter is a rebranded IMST iM871A-USB
Wireless M-Bus USB-adapter. It is used to read wireless water, gas and
electricity meters.
Signed-off-by: Leonard Dallmayr <leonard.dallmayr@mailbox.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 40c304109e866a7dc123661a5c8ca72f6b5e14e0 ]
Supposed DMA cross 4k bounder problem should be fixed at DEV_VER_V2, but
still met problem when do ISO transfer if sg enabled.
Data pattern likes below when sg enabled, package size is 1k and mult is 2
[UVC Header(8B) ] [data(3k - 8)] ...
The received data at offset 0xd000 will get 0xc000 data, len 0x70. Error
happen position as below pattern:
0xd000: wrong
0xe000: wrong
0xf000: correct
0x10000: wrong
0x11000: wrong
0x12000: correct
...
To avoid DMA cross 4k bounder at ISO transfer, reduce burst len according
to start DMA address's alignment.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-4-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92f02efa1d86d7dcaef7f38a5fe3396c4e88a93c ]
ISO basic transfer is
ITP(SOF) Package_0 Package_1 ... Package_n
CDNS3 DMA start dma transfer from memmory to internal FIFO when get SOF,
controller will transfer data to usb bus from internal FIFO when get IN
token.
According USB spec defination:
Maximum number of packets = (bMaxBurst + 1) * (Mult + 1)
Internal memory should be the same as (bMaxBurst + 1) * (Mult + 1). DMA
don't fetch data advance when ISO transfer, so only reserve
(bMaxBurst + 1) * (Mult + 1) internal memory for ISO transfer.
Need save Mult and bMaxBurst information and set it into EP_CFG register,
otherwise only 1 package is sent by controller, other package will be
lost.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-3-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2627335a1329a0d39d8d277994678571c4f21800 ]
Previously, the cdns3_gadget_check_config() function in the cdns3 driver
mistakenly calculated the ep_buf_size by considering only one
configuration's endpoint information because "claimed" will be clear after
call usb_gadget_check_config().
The fix involves checking the private flags EP_CLAIMED instead of relying
on the "claimed" flag.
Fixes: dce49449e04f ("usb: cdns3: allocate TX FIFO size according to composite EP number")
Cc: stable <stable@kernel.org>
Reported-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20230707230015.494999-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 92f02efa1d86 ("usb: cdns3: fix iso transfer error when mult is not zero")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b8be5ecff26201bafb0a554c74e91571299fb94 ]
When IP version >= DEV_VER_V2, gadget:sg_supported is true. So uvc gadget
function driver will use sg to equeue data, first is 8bytes header, the
second is 1016bytes data.
cdns3_prepare_trb: ep2in: trb 0000000000ac755f, dma buf: 0xbf455000, size: 8, burst: 128 ctrl: 0x00000415 (C=1, T=0, ISP, CHAIN, Normal)
cdns3_prepare_trb: ep2in: trb 00000000a574e693, dma buf: 0xc0200fe0, size: 1016, burst: 128 ctrl: 0x00000405 (C=1, T=0, ISP, Normal)
But cdns3_ep_run_transfer() can't correctly handle this case, which only
support one TRB for ISO transfer.
The controller requires duplicate the TD for each SOF if priv_ep->interval
is not 1. DMA will read data from DDR to internal FIFO when get SOF. Send
data to bus when receive IN token. DMA always refill FIFO when get SOF
regardless host send IN token or not. If host send IN token later, some
frames data will be lost.
Fixed it by below major steps:
1. Calculate numembers of TRB base on sg_nums and priv_ep->interval.
2. Remove CHAIN flags for each end TRB of TD when duplicate TD.
3. The controller requires LINK TRB must be first TRB of TD. When check
there are not enough TRBs lefts, just fill LINK TRB for left TRBs.
.... CHAIN_TRB DATA_TRB, CHAIN_TRB DATA_TRB, LINK_TRB ... LINK_TRB
^End of TRB List
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fba8701baed76eac00b84b59f09f6a077f24c534 ]
Patch fixes the following warnings:
cdns3-gadget.c:1203: sparse: warning: incorrect type
in assignment (different base types)
cdns3-gadget.c:1203: sparse: expected restricted __le32 [usertype] length
cdns3-gadget.c:1203: sparse: got unsigned long
cdns3-gadget.c:1250: sparse: warning: invalid assignment: |=
cdns3-gadget.c:1250: sparse: left side has type restricted __le32
cdns3-gadget.c:1250: sparse: right side has type unsigned long
cdns3-gadget.c:1253: sparse: warning: invalid assignment: |=
cdns3-gadget.c:1253: sparse: left side has type restricted __le32
cdns3-gadget.c:1253: sparse: right side has type unsigned long
cdns3-ep0.c:367: sparse: warning: restricted __le16 degrades to integer
cdns3-ep0.c:792: sparse: warning: symbol 'cdns3_gadget_ep0_ops' was not
declared. Should it be static?
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Stable-dep-of: 1b8be5ecff26 ("usb: cdns3: fix uvc failure work since sg support enabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66aad7d8d3ec5a3a8ec2023841bcec2ded5f65c9 ]
In ACM support for sending breaks to devices is optional.
If a device says that it doenot support sending breaks,
the host must respect that.
Given the number of optional features providing tty operations
for each combination is not practical and errors need to be
returned dynamically if unsupported features are requested.
In case a device does not support break, we want the tty layer
to treat that like it treats drivers that statically cannot
support sending a break. It ignores the inability and does nothing.
This patch uses EOPNOTSUPP to indicate that.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 9e98966c7b ("tty: rework break handling")
Link: https://lore.kernel.org/r/20231207132639.18250-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2dd23cc4d0e6aa55cf9fb3b05f2f4165b01de81c upstream.
In mon_bin_vma_fault():
offset = vmf->pgoff << PAGE_SHIFT;
if (offset >= rp->b_size)
return VM_FAULT_SIGBUS;
chunk_idx = offset / CHUNK_SIZE;
pageptr = rp->b_vec[chunk_idx].pg;
The code is executed without holding any lock.
In mon_bin_vma_close():
spin_lock_irqsave(&rp->b_lock, flags);
rp->mmap_active--;
spin_unlock_irqrestore(&rp->b_lock, flags);
In mon_bin_ioctl():
spin_lock_irqsave(&rp->b_lock, flags);
if (rp->mmap_active) {
...
} else {
...
kfree(rp->b_vec);
rp->b_vec = vec;
rp->b_size = size;
...
}
spin_unlock_irqrestore(&rp->b_lock, flags);
Concurrent execution of mon_bin_vma_fault() with mon_bin_vma_close() and
mon_bin_ioctl() could lead to atomicity violations. mon_bin_vma_fault()
accesses rp->b_size and rp->b_vec without locking, risking array
out-of-bounds access or use-after-free bugs due to possible modifications
in mon_bin_ioctl().
This possible bug is found by an experimental static analysis tool
developed by our team, BassCheck[1]. This tool analyzes the locking APIs
to extract function pairs that can be concurrently executed, and then
analyzes the instructions in the paired functions to identify possible
concurrency bugs including data races and atomicity violations. The above
possible bug is reported when our tool analyzes the source code of
Linux 6.2.
To address this issue, it is proposed to add a spin lock pair in
mon_bin_vma_fault() to ensure atomicity. With this patch applied, our tool
never reports the possible bug, with the kernel configuration allyesconfig
for x86_64. Due to the lack of associated hardware, we cannot test the
patch in runtime testing, and just verify it according to the code logic.
[1] https://sites.google.com/view/basscheck/
Fixes: 19e6317d24 ("usb: mon: Fix a deadlock in usbmon between ...")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gui-Dong Han <2045gemini@gmail.com>
Link: https://lore.kernel.org/r/20240105052412.9377-1-2045gemini@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5962ded777d689cd8bf04454273e32228d7fb71f upstream.
When typec_altmode_put_partner is called by a plug altmode upon release,
the port altmode the plug belongs to will not remove its reference to the
plug. The check to see if the altmode being released is a plug evaluates
against the released altmode's partner instead of the calling altmode, so
change adev in typec_altmode_put_partner to properly refer to the altmode
being released.
Because typec_altmode_set_partner calls get_device() on the port altmode,
add partner_adev that points to the port altmode in typec_put_partner to
call put_device() on. typec_altmode_set_partner is not called for port
altmodes, so add a check in typec_altmode_release to prevent
typec_altmode_put_partner() calls on port altmode release.
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Cc: <stable@vger.kernel.org>
Co-developed-by: Christian A. Ehrhardt <lk@c--e.de>
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Tested-by: Christian A. Ehrhardt <lk@c--e.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240103181754.2492492-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 128d849074d05545becf86e713715ce7676fc074 upstream.
After the chipidea driver introduce extcon for id and vbus, it's able
to wakeup from another irq source, in case the system with extcon ID
cable, wakeup from usb ID cable and device removal, the usb device
disconnect irq may come firstly before the extcon notifier while system
resume, so we will get 2 "wakeup" irq, one for usb device disconnect;
and one for extcon ID cable change(real wakeup event), current driver
treat them as 2 successive wakeup irq so can't handle it correctly, then
finally the usb irq can't be enabled. This patch adds a check to bypass
further usb events before controller resume finished to fix it.
Fixes: 1f874edcb7 ("usb: chipidea: add runtime power management support")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20231228110753.1755756-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afe28cd686aeb77e8d9140d50fb1cf06a7ecb731 upstream.
This reverts commit e835c0a4e23c38531dcee5ef77e8d1cf462658c7.
Don't omit soft-reset. During initialization, the driver may need to
perform a soft reset to ensure the phy is ready when the controller
updates the GCTL.PRTCAPDIR or other settings by issuing phy soft-reset.
Many platforms often have access to DCTL register for soft-reset despite
being host-only. If there are actual reported issues from the platforms
that don't expose DCTL registers, then we will need to revisit (perhaps
to teach dwc3 to perform xhci's soft-reset USBCMD.HCRST).
Cc: <stable@vger.kernel.org>
Fixes: e835c0a4e23c ("usb: dwc3: don't reset device side if dwc3 was configured as host-only")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/7668ab11a48f260820825274976eb41fec7f54d1.1703282469.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9d40b215e38480fd94c66b06d79045717a59e9c upstream.
Current implementation blocks the running operations when Plug-out and
Plug-In is performed continuously, process gets stuck in
dwc3_thread_interrupt().
Code Flow:
CPU1
->Gadget_start
->dwc3_interrupt
->dwc3_thread_interrupt
->dwc3_process_event_buf
->dwc3_process_event_entry
->dwc3_endpoint_interrupt
->dwc3_ep0_interrupt
->dwc3_ep0_inspect_setup
->dwc3_ep0_stall_and_restart
By this time if pending_list is not empty, it will get the next request
on the given list and calls dwc3_gadget_giveback which will unmap request
and call its complete() callback to notify upper layers that it has
completed. Currently dwc3_gadget_giveback status is set to -ECONNRESET,
whereas it should be -ESHUTDOWN based on condition if not dwc->connected
is true.
Cc: <stable@vger.kernel.org>
Fixes: d742220b35 ("usb: dwc3: ep0: giveback requests on stall_and_restart")
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20231222094704.20276-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff2b89de471da942a4d853443688113a44fd35ed upstream.
When CONFIG_USB_OTG is not set, mxs_phy_is_otg_host() will always return
false. This behaviour is wrong. Since phy.last_event will always be set
for either host or device mode. Therefore, CONFIG_USB_OTG condition
can be removed.
Fixes: 5eda42aebb76 ("usb: phy: mxs: fix getting wrong state with mxs_phy_is_otg_host()")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20231228110753.1755756-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7fbcd195e2b8cc952e4aeaeb50867b798040314c ]
Here "temp" is the number of characters that we have written and "size"
is the size of the buffer. The intent was clearly to say that if we have
written to the end of the buffer then stop.
However, for that to work the comparison should have been done on the
original "size" value instead of the "size -= temp" value. Not only
will that not trigger when we want to, but there is a small chance that
it will trigger incorrectly before we want it to and we break from the
loop slightly earlier than intended.
This code was recently changed from using snprintf() to scnprintf(). With
snprintf() we likely would have continued looping and passed a negative
size parameter to snprintf(). This would have triggered an annoying
WARN(). Now that we have converted to scnprintf() "size" will never
drop below 1 and there is no real need for this test. We could change
the condition to "if (temp <= 1) goto done;" but just deleting the test
is cleanest.
Fixes: 7d50195f6c ("usb: host: Faraday fotg210-hcd driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/ZXmwIwHe35wGfgzu@suswa
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 513d88a88e0203188a38f4647dd08170aebd85df upstream.
Update the constant names for unused USB PIDs (product identifiers) to
reflect the new products now using the PIDs.
Signed-off-by: Mark Glover <mark.glover@actisense.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73ea73affe8622bdf292de898da869d441da6a9d upstream.
The KOBJ_CHANGE uevent is sent before gadget unbind is actually
executed, resulting in inaccurate uevent emitted at incorrect timing
(the uevent would have USB_UDC_DRIVER variable set while it would
soon be removed).
Move the KOBJ_CHANGE uevent to the end of the unbind function so that
uevent is sent only after the change has been made.
Fixes: 2ccea03a8f ("usb: gadget: introduce UDC Class")
Cc: stable@vger.kernel.org
Signed-off-by: Roy Luo <royluo@google.com>
Link: https://lore.kernel.org/r/20231128221756.2591158-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b17b7fe6dd5c6ff74b38b0758ca799cdbb79e26e upstream.
When typec_altmode_put_partner is called by a plug altmode upon release,
the port altmode the plug belongs to will not remove its reference to the
plug. The check to see if the altmode being released evaluates against the
released altmode's partner instead of the calling altmode itself, so change
adev in typec_altmode_put_partner to properly refer to the altmode being
released.
typec_altmode_set_partner is not run for port altmodes, so also add a check
in typec_altmode_release to prevent typec_altmode_put_partner() calls on
port altmode release.
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231129192349.1773623-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61890dc28f7d9e9aac8a9471302613824c22fae4 upstream.
The commit 89ff3dfac604 ("usb: gadget: f_hid: fix f_hidg lifetime vs
cdev") has introduced a bug that leads to hid device corruption after
the replug operation.
Reverse device managed memory allocation for the report descriptor
to fix the issue.
Tested:
This change was tested on the AMD EthanolX CRB server with the BMC
based on the OpenBMC distribution. The BMC provides KVM functionality
via the USB gadget device:
- before: KVM page refresh results in a broken USB device,
- after: KVM page refresh works without any issues.
Fixes: 89ff3dfac604 ("usb: gadget: f_hid: fix f_hidg lifetime vs cdev")
Cc: stable@vger.kernel.org
Signed-off-by: Konstantin Aladyshev <aladyshev22@gmail.com>
Link: https://lore.kernel.org/r/20231206080744.253-2-aladyshev22@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 70f400d4d957c2453c8689552ff212bc59f88938 ]
Move the "removable" attribute from USB to core in order to allow it to be
supported by other subsystem / buses. Individual buses that want to support
this attribute can populate the removable property of the device while
enumerating it with the 3 possible values -
- "unknown"
- "fixed"
- "removable"
Leaving the field unchanged (i.e. "not supported") would mean that the
attribute would not show up in sysfs for that device. The UAPI (location,
symantics etc) for the attribute remains unchanged.
Move the "removable" attribute from USB to the device core so it can be
used by other subsystems / buses.
By default, devices do not have a "removable" attribute in sysfs.
If a subsystem or bus driver wants to support a "removable" attribute, it
should call device_set_removable() before calling device_register() or
device_add(), e.g.:
device_set_removable(dev, DEVICE_REMOVABLE);
device_register(dev);
The possible values and the resulting sysfs attribute contents are:
DEVICE_REMOVABLE_UNKNOWN -> "unknown"
DEVICE_REMOVABLE -> "removable"
DEVICE_FIXED -> "fixed"
Convert the USB "removable" attribute to use this new device core
functionality. There should be no user-visible change in the location or
semantics of attribute for USB devices.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Link: https://lore.kernel.org/r/20210524171812.18095-1-rajatja@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 432e664e7c98 ("drm/amdgpu: don't use ATRM for external devices")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 974bba5c118f4c2baf00de0356e3e4f7928b4cbc ]
The BOS descriptor defines a root descriptor and is the base descriptor for
accessing a family of related descriptors.
Function 'usb_get_bos_descriptor()' encounters an iteration issue when
skipping the 'USB_DT_DEVICE_CAPABILITY' descriptor type. This results in
the same descriptor being read repeatedly.
To address this issue, a 'goto' statement is introduced to ensure that the
pointer and the amount read is updated correctly. This ensures that the
function iterates to the next descriptor instead of reading the same
descriptor repeatedly.
Cc: stable@vger.kernel.org
Fixes: 3dd550a2d3 ("USB: usbcore: Fix slab-out-of-bounds bug during device reset")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231115121325.471454-1-niklas.neronin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a09c1269702db8eccb6f718da2b00173e1e0034 ]
It has been pointed out that the kernel log messages warning about
problems in USB configuration and related descriptors are vexing for
users. The warning log level has a fairly high priority, but the user
can do nothing to fix the underlying errors in the device's firmware.
To reduce the amount of useless information produced by tools that
filter high-priority log messages, we can change these warnings to
notices, i.e., change dev_warn() to dev_notice(). The same holds for
a few messages that currently use dev_err(): Unless they indicate a
failure that might make a device unusable (such as inability to
transfer a config descriptor), change them to dev_notice() also.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216630
Suggested-by: Artem S. Tashkinov <aros@gmx.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Y2KzPx0h6z1jXCuN@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 974bba5c118f ("usb: config: fix iteration issue in 'usb_get_bos_descriptor()'")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 41f5a0973259db9e4e3c9963d36505f80107d1a0 upstream.
The Qualcomm glue driver is overriding the interrupt trigger types
defined by firmware when requesting the wakeup interrupts during probe.
This can lead to a failure to map the DP/DM wakeup interrupts after a
probe deferral as the firmware defined trigger types do not match the
type used for the initial mapping:
irq: type mismatch, failed to map hwirq-14 for interrupt-controller@b220000!
irq: type mismatch, failed to map hwirq-15 for interrupt-controller@b220000!
Fix this by not overriding the firmware provided trigger types when
requesting the wakeup interrupts.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org # 4.18
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231120161607.7405-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0583bc776ca5b5a3f5752869fc31cf7322df2b35 upstream.
dwc2_hc_n_intr() writes back INTMASK as read but evaluates it
with intmask applied. In stress testing this causes spurious
interrupts like this:
[Mon Aug 14 10:51:07 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 7 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:07 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 0 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 4 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_update_urb_state_abn(): trimming xfer length
Applying INTMASK prevents this. The issue exists in all versions of the
driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: Ivan Ivanov <ivan.ivanov@suse.com>
Tested-by: Andrea della Porta <andrea.porta@suse.com>
Link: https://lore.kernel.org/r/20231115144514.15248-1-oneukum@suse.com
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 51392a1879ff06dc21b68aef4825f6ef68a7be42 ]
The driver needs to deregister and free the newly allocated dwc3 core
platform device on ACPI probe errors (e.g. probe deferral) and on driver
unbind but instead it leaked those resources while erroneously dropping
a reference to the parent platform device which is still in use.
For OF probing the driver takes a reference to the dwc3 core platform
device which has also always been leaked.
Fix the broken ACPI tear down and make sure to drop the dwc3 core
reference for both OF and ACPI.
Fixes: 8fd95da2cfb5 ("usb: dwc3: qcom: Release the correct resources in dwc3_qcom_remove()")
Fixes: 2bc02355f8 ("usb: dwc3: qcom: Add support for booting with ACPI")
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org # 4.18
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Lee Jones <lee@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231117173650.21161-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 9cf87666fc6e ("USB: dwc3: qcom: fix ACPI platform device leak")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4db356924a50f72a00834ae04f11202d9703faeb ]
Refactor handler for stop endpoint command completion. Yank out the part
that invalidates cancelled TDs and turn it into a separate function.
Invalidating cancelled TDs should be done while the ring is stopped,
but not exclusively in the stop endpoint command completeion handler.
We will need to invalidate TDs after resetting endpoints as well.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: a5f928db5951 ("usb: host: xhci-plat: fix possible kernel oops while resuming")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a04224da1f3424b2c607b12a3bd1f0e302fb8231 ]
Previously, gadget assignment to the net device occurred exclusively
during the initial binding attempt.
Nevertheless, the gadget pointer could change during bind/unbind
cycles due to various conditions, including the unloading/loading
of the UDC device driver or the detachment/reconnection of an
OTG-capable USB hub device.
This patch relocates the gether_set_gadget() function out from
ncm_opts->bound condition check, ensuring that the correct gadget
is assigned during each bind request.
The provided logs demonstrate the consistency of ncm_opts throughout
the power cycle, while the gadget may change.
* OTG hub connected during boot up and assignment of gadget and
ncm_opts pointer
[ 2.366301] usb 2-1.5: New USB device found, idVendor=2996, idProduct=0105
[ 2.366304] usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.366306] usb 2-1.5: Product: H2H Bridge
[ 2.366308] usb 2-1.5: Manufacturer: Aptiv
[ 2.366309] usb 2-1.5: SerialNumber: 13FEB2021
[ 2.427989] usb 2-1.5: New USB device found, VID=2996, PID=0105
[ 2.428959] dabridge 2-1.5:1.0: dabridge 2-4 total endpoints=5, 0000000093a8d681
[ 2.429710] dabridge 2-1.5:1.0: P(0105) D(22.06.22) F(17.3.16) H(1.1) high-speed
[ 2.429714] dabridge 2-1.5:1.0: Hub 2-2 P(0151) V(06.87)
[ 2.429956] dabridge 2-1.5:1.0: All downstream ports in host mode
[ 2.430093] gadget 000000003c414d59 ------> gadget pointer
* NCM opts and associated gadget pointer during First ncm_bind
[ 34.763929] NCM opts 00000000aa304ac9
[ 34.763930] NCM gadget 000000003c414d59
* OTG capable hub disconnecte or assume driver unload.
[ 97.203114] usb 2-1: USB disconnect, device number 2
[ 97.203118] usb 2-1.1: USB disconnect, device number 3
[ 97.209217] usb 2-1.5: USB disconnect, device number 4
[ 97.230990] dabr_udc deleted
* Reconnect the OTG hub or load driver assaign new gadget pointer.
[ 111.534035] usb 2-1.1: New USB device found, idVendor=2996, idProduct=0120, bcdDevice= 6.87
[ 111.534038] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 111.534040] usb 2-1.1: Product: Vendor
[ 111.534041] usb 2-1.1: Manufacturer: Aptiv
[ 111.534042] usb 2-1.1: SerialNumber: Superior
[ 111.535175] usb 2-1.1: New USB device found, VID=2996, PID=0120
[ 111.610995] usb 2-1.5: new high-speed USB device number 8 using xhci-hcd
[ 111.630052] usb 2-1.5: New USB device found, idVendor=2996, idProduct=0105, bcdDevice=21.02
[ 111.630055] usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 111.630057] usb 2-1.5: Product: H2H Bridge
[ 111.630058] usb 2-1.5: Manufacturer: Aptiv
[ 111.630059] usb 2-1.5: SerialNumber: 13FEB2021
[ 111.687464] usb 2-1.5: New USB device found, VID=2996, PID=0105
[ 111.690375] dabridge 2-1.5:1.0: dabridge 2-8 total endpoints=5, 000000000d87c961
[ 111.691172] dabridge 2-1.5:1.0: P(0105) D(22.06.22) F(17.3.16) H(1.1) high-speed
[ 111.691176] dabridge 2-1.5:1.0: Hub 2-6 P(0151) V(06.87)
[ 111.691646] dabridge 2-1.5:1.0: All downstream ports in host mode
[ 111.692298] gadget 00000000dc72f7a9 --------> new gadget ptr on connect
* NCM opts and associated gadget pointer during second ncm_bind
[ 113.271786] NCM opts 00000000aa304ac9 -----> same opts ptr used during first bind
[ 113.271788] NCM gadget 00000000dc72f7a9 ----> however new gaget ptr, that will not set
in net_device due to ncm_opts->bound = true
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Link: https://lore.kernel.org/r/20231020153324.82794-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5f928db59519a15e82ecba4ae3e7cbf5a44715a ]
If this driver enables the xHC clocks while resuming from sleep, it calls
clk_prepare_enable() without checking for errors and blithely goes on to
read/write the xHC's registers -- which, with the xHC not being clocked,
at least on ARM32 usually causes an imprecise external abort exceptions
which cause kernel oops. Currently, the chips for which the driver does
the clock dance on suspend/resume seem to be the Broadcom STB SoCs, based
on ARM32 CPUs, as it seems...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Fixes: 8bd954c56197 ("usb: host: xhci-plat: suspend and resume clocks")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
