HDMI_TX_CEC_LINE pin is used for CEC, so pass it in the device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit c26ebe98a1 ("PCI: imx6: Add regulator support"), it is
possible to pass the 'vpcie-supply' property to describe the PCIE supply.
This way we can remove the 'regulator-always-on' property from the
regulator and have a better device tree description.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6q, imx6dl icore-rqs modules share common sound nodes,
so move the sound nodes from imx6q-icore-rqs into dtsi so-that
both can share the common node details.
And also replace codec: sgtl5000@0a => sgtl5000: codec@a
on imx6q-icore-rqs.dts to [label:] node-name[@unit-address]
according to devicetree specification from ePAPER v1.1
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add basic board support for the Ubiquiti UniFi Switch 8 port model. This
is a small home and office use managed switch based on the BCM53342
switching control SoC.
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Describe the Broadcom Hurricane 2 SoC comprised of a Cortex-A9 CPU
complex along with standard iProc peripherals:
* timers
* SPI controller
* NAND controller
* a single AMAC (Ethernet MAC controller)
* dual PCIe controllers
The design is largely similar to existing iProc-based SoCs such as
Northstar Plus.
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable ostm0 and ostm1 timers to be used as clock source and clockevent
source. The timers provides greater accuracy than the already enabled
mtu2 one.
With these enabled:
clocksource: ostm: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 57352151442 ns
sched_clock: 32 bits at 33MHz, resolution 30ns, wraps every 64440619504ns
ostm: used for clocksource
ostm: used for clock events
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Suggested-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The following 'capacity-dmips-mhz' dt property values are used:
Cortex-A15: 1024, Cortex-A7: 539
They have been derived form the cpu_efficiency values:
Cortex-A15: 3891, Cortex-A7: 2048
by scaling them so that the Cortex-A15s (big cores) use 1024.
The cpu_efficiency values were originally derived from the "Big.LITTLE
Processing with ARM Cortex™-A15 & Cortex-A7" white paper
(http://www.cl.cam.ac.uk/~rdm34/big.LITTLE.pdf). Table 1 lists 1.9x
(3891/2048) as the Cortex-A15 vs Cortex-A7 performance ratio for the
Dhrystone benchmark.
The following platform is affected once cpu-invariant accounting
support is re-connected to the task scheduler:
r8a7790-lager
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Meson6, Meson8 and Meson8b are using the same MMC controller IP. This
adds the MMC controller node to meson.dtsi so it can be used by all
SoCs.
The controller itself is a bit special, because it has multiple slots.
Each slot is accessed through a sub-node of the controller. However,
currently the driver for this hardware only supports one slot.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This DTS has support for the Fairphone 2 (codenamed FP2).
This first version of the DTS supports just the serial console via the
MSM UART pins.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the GSBI6 and GSBI7 IO blocks to the MSM8660 DTSI file.
On the APQ8060 DragonBoard, GSBI6 DM is used for Bluetooth UART,
and GSBI7 I2C is used for FM radio I2C.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds a basic DTS file for the Sony Xperia Z2 Tablet, containing
definitions for regulators, eMMC/SD-card, USB, WiFi, Touchscreen,
charger, backlight, coincell and buttons.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch marks gsbi i2c node at soc level dtsi, so that kernel
would not assume that its enabled and result in pin conflicts on
some boards like IFC6410 which do use these pins for uart.
Without this patch we see below pin conflict:
apq8064-pinctrl 800000.pinctrl: pin GPIO_16 already requested by
16540000.serial; cannot claim for 16580000.i2c
apq8064-pinctrl 800000.pinctrl: pin-16 (16580000.i2c) status -22
apq8064-pinctrl 800000.pinctrl: could not request pin 16 (GPIO_16)
from group gpio16 on device 800000.pinctrl
i2c_qup 16580000.i2c: Error applying setting, reverse things back
i2c_qup: probe of 16580000.i2c failed with error -22
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the necessary #phy-cells property to the DSI and HDMI
phys.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
The devicetree prefix mcp is deprecated in favour of microchip. Thus
this replaces mcp with microchip for the mcp23017 gpio expander chip.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the pcie_rc node to common file so that it can be
used by dra76-evm as well.
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per recent TRM, PBIAS cell on omap5 devices supports
3.3v and not 3.0v as documented earlier.
Update PBIAS regulator max voltage to match this.
Document reference:
SWPU249AF - OMAP543x Technical reference manual August 2016
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per recent TRM, PBIAS cell on dra7 devices supports
3.3v and not 3.0v as documented earlier.
Update PBIAS regulator max voltage to match this.
Document reference:
SPRUI30C – DRA75x, DRA74x Technical reference manual- November 2016
Tested on:
DRA75x PG 2.0 REV H EVM
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All the A31/A31s devices I own have some kind of HDMI connector wired
to the dedicated HDMI pins on the SoC:
- A31 Hummingbird (standard HDMI connector, display already enabled)
- Sinlinx SinA31s (standard HDMI connector)
- MSI Primo81 tablet (micro HDMI connector)
Enable the display pipeline (if needed) and HDMI output for them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we support the HDMI controller on the A31 SoC, we can add it
to the device tree.
This adds a device node for the HDMI controller, and the of_graph nodes
connecting it to the 2 TCONs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The TRM has marked dra7 SmartReflex as reserved and we should not
touch those registers as pointed out by Nishanth Menon <nm@ti.com>.
We do still want to idle the related interconnect target modules on
init though.
Let's do this by only configuring the generic interconnect target modules
and not add the child SmartReflex devices.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On omap4 we are missing dts nodes for several interconnect target
modules that we are idling on init. This currently works with the
legacy platform data still around.
To fix this, let's add the interconnect target modules so we can
idle the unused interconnect target module on init.
Also note that adding the interconnect target module node does not
necessarily mean that there is a driver available for the child IP
block, or that the child IP block is even functional.
In the SGX case, the PowerVR driver is closed source. And McASP on
omap4 has at least the TX path disabled and is not supported by the
davinci-mcasp driver. For AESS there is old Android 3.4 kernel
driver available.
For smarflex, we are still probing with platform data and the
driver needs more work before we can add the device ip child nodes.
And finally, we're not yet using the interconnet ranges. I will
be posting separate patches for those later on.
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
K2G EVM has n25q128a13 SPI NOR flash on SPI1. Enable SPI1 in the DT
node as well as add a subnode for the SPI NOR.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Add nodes for the various SPI instances.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Enable PWM ECAP0 which will be used for display backlight.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Enable USB 0 which will be used as a host port and USB 1 which will be
used in peripheral mode.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Add nodes for both USB instances supported by 66AK2G.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
K2G EVM has an onboard I2C EEPROM connected to I2C0. This patch adds
the necessary DT entry for the AT24CM01 EEPROM.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
