If the driver is unloaded when D3 debug data pulling is enabled
but not triggered, it doesn't release the data buffer.
Fix this by adding iwl_fw_runtime_free and calling it from the
relevant places.
Fixes: 2d8c261511 ("iwlwifi: add d3 debug data support")
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the firmware starts, it doesn't have any regulatory
information, hence it uses the world wide limitations. The
driver can feed the firmware with previous knowledge that
was kept in the driver, but the firmware may still not
update its internal tables.
This happens when we start a BSS interface, and then the
firmware can change the regulatory tables based on our
location and it'll use more lenient, location specific
rules. Then, if the firmware is shut down (when the
interface is brought down), and then an AP interface is
created, the firmware will forget the country specific
rules.
The host will think that we are in a certain country that
may allow channels and will try to teach the firmware about
our location, but the firmware may still not allow to drop
the world wide limitations and apply country specific rules
because it was just re-started.
In this case, the firmware will reply with MCC_RESP_ILLEGAL
to the MCC_UPDATE_CMD. In that case, iwlwifi needs to let
the upper layers (cfg80211 / hostapd) know that the channel
list they know about has been updated.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201105
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The oldest firmware supported by iwlmvm do support getting
the average beacon RSSI. Enable the sta_statistics() call
from mac80211 even on older firmware versions.
Fixes: 33cef92563 ("iwlwifi: mvm: support beacon statistics for BSS client")
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
From coreboot/BIOS:
Name ("WGDS", Package() {
Revision,
Package() {
DomainType, // 0x7:WiFi ==> We miss this one.
WgdsWiFiSarDeltaGroup1PowerMax1, // Group 1 FCC 2400 Max
WgdsWiFiSarDeltaGroup1PowerChainA1, // Group 1 FCC 2400 A Offset
WgdsWiFiSarDeltaGroup1PowerChainB1, // Group 1 FCC 2400 B Offset
WgdsWiFiSarDeltaGroup1PowerMax2, // Group 1 FCC 5200 Max
WgdsWiFiSarDeltaGroup1PowerChainA2, // Group 1 FCC 5200 A Offset
WgdsWiFiSarDeltaGroup1PowerChainB2, // Group 1 FCC 5200 B Offset
WgdsWiFiSarDeltaGroup2PowerMax1, // Group 2 EC Jap 2400 Max
WgdsWiFiSarDeltaGroup2PowerChainA1, // Group 2 EC Jap 2400 A Offset
WgdsWiFiSarDeltaGroup2PowerChainB1, // Group 2 EC Jap 2400 B Offset
WgdsWiFiSarDeltaGroup2PowerMax2, // Group 2 EC Jap 5200 Max
WgdsWiFiSarDeltaGroup2PowerChainA2, // Group 2 EC Jap 5200 A Offset
WgdsWiFiSarDeltaGroup2PowerChainB2, // Group 2 EC Jap 5200 B Offset
WgdsWiFiSarDeltaGroup3PowerMax1, // Group 3 ROW 2400 Max
WgdsWiFiSarDeltaGroup3PowerChainA1, // Group 3 ROW 2400 A Offset
WgdsWiFiSarDeltaGroup3PowerChainB1, // Group 3 ROW 2400 B Offset
WgdsWiFiSarDeltaGroup3PowerMax2, // Group 3 ROW 5200 Max
WgdsWiFiSarDeltaGroup3PowerChainA2, // Group 3 ROW 5200 A Offset
WgdsWiFiSarDeltaGroup3PowerChainB2, // Group 3 ROW 5200 B Offset
}
})
When read the ACPI data to find out the WGDS, the DATA_SIZE is never
matched.
From the above format, it gives 19 numbers, but our driver is hardcode
as 18.
Fix it to pass then can parse the data into our wgds table.
Then we will see:
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init Sending GEO_TX_POWER_LIMIT
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[0]
Band[0]: chain A = 68 chain B = 69 max_tx_power = 54
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[0]
Band[1]: chain A = 48 chain B = 49 max_tx_power = 70
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[1]
Band[0]: chain A = 51 chain B = 67 max_tx_power = 50
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[1]
Band[1]: chain A = 69 chain B = 70 max_tx_power = 68
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[2]
Band[0]: chain A = 49 chain B = 50 max_tx_power = 48
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[2]
Band[1]: chain A = 52 chain B = 53 max_tx_power = 51
Cc: stable@vger.kernel.org # 4.12+
Fixes: a6bff3cb19 ("iwlwifi: mvm: add GEO_TX_POWER_LIMIT cmd for geographic tx power table")
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
with CONFIG_THERMAL=m and cxgb4 as built-in build fails, and
'commit e70a57fa59 ("cxgb4: fix thermal configuration dependencies")'
tries to fix it but when cxgb4i is made built-in build fails again,
use IS_REACHABLE instead of IS_ENABLED to fix the issue.
Fixes: e70a57fa59 (cxgb4: fix thermal configuration dependencies)
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To keep track of the number of times the workaround code for 57500 A0
has been triggered. This is a per NQ counter.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware can sometimes not generate NQ MSIX with a single pending
CP ring entry. This seems to always happen at the last entry of
the CP ring before it wraps. Add logic to check all the CP rings for
pending entries without the CP ring consumer index advancing. Calling
HWRM_DBG_RING_INFO_GET to read the context of the CP ring will flush
out the NQ entry and MSIX.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no RDMA support on 57500 chips yet, so prevent bnxt_re from
registering on these chips. There is intermittent failure if bnxt_re
is allowed to register and proceed with RDMA operations.
Fixes: 1ab968d2f1 ("bnxt_en: Add PCI ID for BCM57508 device.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The software counter structure is defined in both the CP ring's structure
and the NQ ring's structure on the new devices. The legacy code adds the
counter to the CP ring's structure and the counter won't get displayed
since the ethtool code is looking at the NQ ring's structure.
Since all other counters are contained in the NQ ring's structure, it
makes more sense to count rx_l4_csum_errors in the NQ.
Fixes: 50e3ab7836 ("bnxt_en: Allocate completion ring structures for 57500 series chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent commit has added the reservation of RSS context. This requires
bnxt_hwrm_vnic_qcaps() to be called before allocating any RSS contexts.
The bnxt_hwrm_vnic_qcaps() call sets up proper flags that will
determine how many RSS contexts to allocate to support NTUPLE.
This causes a regression that too many RSS contexts are being reserved
and causing resource shortage when enabling many VFs. Fix it by calling
bnxt_hwrm_vnic_qcaps() earlier.
Fixes: 41e8d79837 ("bnxt_en: Modify the ring reservation functions for 57500 series chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of "sb_index" is written by the hardware. Reading its value and
writing it to "index" must finish before checking the loop condition.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain flows need to access the rdma-info structure, for example dcbx
update flows. In some cases there can be a race between the allocation or
deallocation of the structure which was done in roce start / roce stop and
an asynchrounous dcbx event that tries to access the structure.
For this reason, we move the allocation of the rdma_info structure to be
similar to the iscsi/fcoe info structures which are allocated during device
setup.
We add a new field of "active" to the struct to define whether roce has
already been started or not, and this is checked instead of whether the
pointer to the info structure.
Fixes: 51ff17251c ("qed: Add support for RoCE hw init")
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TC received from APP TLV is stored in offload_tc, and should not be
set by protocols which did not receive an APP TLV. Fixed the condition
when overriding the offload_tc.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
pull-request: can 2018-11-09
this is a pull request of 20 patches for net/master.
First we have a patch by Oliver Hartkopp which changes the raw socket's
raw_sendmsg() to return an error value if the user tries to send a CANFD
frame to a CAN-2.0 device.
The next two patches are by Jimmy Assarsson and fix potential problems
in the kvaser_usb driver.
YueHaibing's patches for the ucan driver fix a compile time warning and
remove a duplicate include.
Eugeniu Rosca patch adds more binding documentation to the rcar_can
driver bindings. The next two patches are by Fabrizio Castro for the
rcar_can driver and fixes a problem in the driver's probe function and
document the r8a774a1 binding.
Lukas Wunner's patch fixes a recpetion problem in hi311x driver by
switching from edge to level triggered interruts.
The next three patches all target the flexcan driver. Pankaj Bansal's
patch unconditionally unlocks the last mailbox used for RX. Alexander
Stein provides a better workaround for a hardware limitation when
sending RTR frames, by using the last mailbox for TX, resulting in fewer
lost frames. The patch by me simplyfies the driver, by making a runtime
value a compile time constant.
The following 4 patches are by me and provide the groundwork for the
next patches by Oleksij Rempel. To avoid code duplication common code in
the common CAN driver infrastructure is factured out and error handling
is cleaned up.
The next 4 patches are by Oleksij Rempel and fix the problem in the
flexcan driver that other processes see TX frames arrive out of order
with ragards to a RX'ed frame (which are send by a different system on
the CAN bus as the result of our TX frame).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver assigns DMAE channel 0 for FW as part of START_RAMROD command. FW
uses this channel for DMAE operations (e.g., TIME_SYNC implementation).
Driver also uses the same channel 0 for DMAE operations for some of the PFs
(e.g., PF0 on Port0). This could lead to concurrent access to the DMAE
channel by FW and driver which is not legal. Hence need to assign unique
DMAE id for FW.
Currently following DMAE channels are used by the clients,
MFW - OCBB/OCSD functionality uses DMAE channel 14/15
Driver 0-3 and 8-11 (for PF dmae operations)
4 and 12 (for stats requests)
Assigning unique dmae_id '13' to the FW.
Changes from previous version:
------------------------------
v2: Incorporated the review comments.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6161 would sometime fail to probe with a timeout waiting for
the switch to complete an operation. This operation is supposed to
clear the statistics counters. However, due to a read/modify/write,
without the needed mask, the operation actually carried out was more
random, with invalid parameters, resulting in the switch not
responding. We need to preserve the histogram mode bits, so apply a
mask to keep them.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 40cff8fca9 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A null dereference was observed when a sysctl was being set
from userspace and rmnet was stuck trying to complete some actions
in the NETDEV_REGISTER callback. This is because the real_dev is set
only after the device registration handler completes.
sysctl call stack -
<6> Unable to handle kernel NULL pointer dereference at
virtual address 00000108
<2> pc : rmnet_vnd_get_iflink+0x1c/0x28
<2> lr : dev_get_iflink+0x2c/0x40
<2> rmnet_vnd_get_iflink+0x1c/0x28
<2> inet6_fill_ifinfo+0x15c/0x234
<2> inet6_ifinfo_notify+0x68/0xd4
<2> ndisc_ifinfo_sysctl_change+0x1b8/0x234
<2> proc_sys_call_handler+0xac/0x100
<2> proc_sys_write+0x3c/0x4c
<2> __vfs_write+0x54/0x14c
<2> vfs_write+0xcc/0x188
<2> SyS_write+0x60/0xc0
<2> el0_svc_naked+0x34/0x38
device register call stack -
<2> notifier_call_chain+0x84/0xbc
<2> raw_notifier_call_chain+0x38/0x48
<2> call_netdevice_notifiers_info+0x40/0x70
<2> call_netdevice_notifiers+0x38/0x60
<2> register_netdevice+0x29c/0x3d8
<2> rmnet_vnd_newlink+0x68/0xe8
<2> rmnet_newlink+0xa0/0x160
<2> rtnl_newlink+0x57c/0x6c8
<2> rtnetlink_rcv_msg+0x1dc/0x328
<2> netlink_rcv_skb+0xac/0x118
<2> rtnetlink_rcv+0x24/0x30
<2> netlink_unicast+0x158/0x1f0
<2> netlink_sendmsg+0x32c/0x338
<2> sock_sendmsg+0x44/0x60
<2> SyS_sendto+0x150/0x1ac
<2> el0_svc_naked+0x34/0x38
Fixes: b752eff5be ("net: qualcomm: rmnet: Implement ndo_get_iflink")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets with marked invalid IP/UDP/TCP checksums were considered as good
by the driver. The error was in a logic, processing offload bits in
RX descriptor.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a condition mistake due to which macvlans unicast
item number 32 was not added in the unicast filter.
The consequence is that when exactly 32 macvlans are created
on NIC, the last created macvlan receives no traffic because
its MAC was not registered in HW.
Fixes: 94b3b54230 ("net: aquantia: vlan unicast address list correct handling")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IOMMU fault may occurr on unbind/bind or if_down/if_up sequence.
Although driver disables the rings on down, this is not enough.
Due to internal HW design, during subsequent initialization
NIC sometimes may reuse RX descriptors cache and write to the
host memory from the descriptor cache.
That's get catched by IOMMU on host.
This patch invalidates the descriptor cache in NIC on interface down
to prevent writing to the cached descriptors and to the memory pointed
in those descriptors.
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control statuses were not synchronized between blocks,
that caused packets/link drop on some corner cases, when
MAC sent PFC although Phy was not expecting these to come.
Driver should readout the negotiated FC from phy and
configure RX block accordigly.
This is done on each link change event with information from FW.
Fixes: 288551de45 ("net: aquantia: Implement rx/tx flow control ethtools callback")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in case of bus error, driver will generate error message and put
in the tail of the message queue. To avoid confusions, this change should
place the bus related messages in proper order.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Current flexcan driver will put TX-ECHO in regular unsorted way, in
this case TX-ECHO can come after the response to the same TXed message.
In some cases, for example for J1939 stack, things will break.
This patch is using new rx-offload API to put the messages just in the
right place.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Current CAN framework can't guarantee proper/chronological order
of RX and TX-ECHO messages. To make this possible, drivers should use
this functions instead of can_get_echo_skb().
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Prior to echoing a successfully transmitted CAN frame (by calling
can_get_echo_skb()), CAN drivers have to put the CAN frame (by calling
can_put_echo_skb() in the transmit function). These put and get function
take an index as parameter, which is used to identify the CAN frame.
A driver calling can_get_echo_skb() with a index not pointing to a skb
is a BUG, so add an appropriate error message.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the "struct can_priv::echo_skb" is accessed out of bounds would lead
to a kernel crash. Better print a sensible warning message instead and
try to recover.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch replaces the use of "struct can_frame::can_dlc" by "struct
canfd_frame::len" to access the frame's length. As it is ensured that
both structures have a compatible memory layout for this member this is
no functional change. Futher, this compatibility is documented in a
comment.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch factors out all non sending parts of can_get_echo_skb() into
a seperate function __can_get_echo_skb(), so that it can be re-used in
an upcoming patch.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The previous patch changes the TX path to always use the last mailbox
regardless of the used offload scheme (rx-fifo or timestamp based). This
means members "tx_mb" and "tx_mb_idx" of the struct flexcan_priv don't
depend on the offload scheme, so replace them by compile time constants.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Essentially this patch moves the TX mailbox to position 63, regardless
of timestamp based offloading or RX FIFO. So mainly the iflag register
usage regarding TX has changed. The rest is consolidating RX FIFO and
timestamp offloading as they now use both the same TX mailbox.
The reason is a very annoying behavior regarding sending RTR frames when
_not_ using RX FIFO:
If a TX mailbox sent a RTR frame it becomes a RX mailbox. For that
reason flexcan_irq disables the TX mailbox again. But if during the time
the RTR was sent and the TX mailbox is disabled a new CAN frames is
received, it is lost without notice. The reason is that so-called
"Move-in" process starts from the lowest mailbox which happen to be a TX
mailbox set to EMPTY.
Steps to reproduce (I used an imx7d):
1. generate regular bursts of messages
2. send a RTR from flexcan with higher priority than burst messages every
1ms, e.g. cangen -I 0x100 -L 0 -g 1 -R can0
3. notice a lost message without notification after some seconds
When running an iperf in parallel this problem is occurring even more
frequently. Using filters is not possible as at least one single CAN-ID
is allowed. Handling the TX MB during RX is also not possible as there
is no race-free disable of RX MB.
There is still a slight window when the described problem can occur. But
for that all RX MB must be in use which is essentially next to an
overrun. Still there will be no indication if it ever occurs.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Unlock the MB irrespective of reception method being FIFO or timestamp
based. It is optional but recommended to unlock Mailbox as soon as
possible and make it available for reception.
Reported-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the hi3110 shares the SPI bus with another traffic-intensive device
and packets are received in high volume (by a separate machine sending
with "cangen -g 0 -i -x"), reception stops after a few minutes and the
counter in /proc/interrupts stops incrementing. Bus state is "active".
Bringing the interface down and back up reconvenes the reception. The
issue is not observed when the hi3110 is the sole device on the SPI bus.
Using a level-triggered interrupt makes the issue go away and lets the
hi3110 successfully receive 2 GByte over the course of 5 days while a
ks8851 Ethernet chip on the same SPI bus handles 6 GByte of traffic.
Unfortunately the hi3110 datasheet is mum on the trigger type. The pin
description on page 3 only specifies the polarity (active high):
http://www.holtic.com/documents/371-hi-3110_v-rev-kpdf.do
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Assigning 2 to "renesas,can-clock-select" tricks the driver into
registering the CAN interface, even though we don't want that.
This patch improves one of the checks to prevent that from happening.
Fixes: 862e2b6af9 ("can: rcar_can: support all input clocks")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/can/usb/ucan.c: In function 'ucan_disconnect':
drivers/net/can/usb/ucan.c:1578:21: warning:
variable 'udev' set but not used [-Wunused-but-set-variable]
struct usb_device *udev;
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The call to can_put_echo_skb() may result in the skb being freed. The skb
is later used in the call to dev->ops->dev_frame_to_cmd().
This is avoided by moving the call to can_put_echo_skb() after
dev->ops->dev_frame_to_cmd().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no unregister netlink notifier and family on error paths
in init_mac80211_hwsim(). Also there is an error path where
hwsim_class is not destroyed.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 62759361eb ("mac80211-hwsim: Provide multicast event for HWSIM_CMD_NEW_RADIO")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The commit f77f0aee4d ("net: use core MTU range checking in USB NIC
drivers") introduce a common MTU handling for usbnet. But it's missing
the necessary changes for smsc95xx. So set the MTU range accordingly.
This patch has been tested on a Raspberry Pi 3.
Fixes: f77f0aee4d ("net: use core MTU range checking in USB NIC drivers")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ping problems with packets > 8191 as shown:
PING 192.168.1.99 (192.168.1.99) 8150(8178) bytes of data.
8158 bytes from 192.168.1.99: icmp_seq=1 ttl=64 time=0.669 ms
wrong data byte 8144 should be 0xd0 but was 0x0
16 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f
20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f
%< ---------------snip--------------------------------------
8112 b0 b1 b2 b3 b4 b5 b6 b7 b8 b9 ba bb bc bd be bf
c0 c1 c2 c3 c4 c5 c6 c7 c8 c9 ca cb cc cd ce cf
8144 0 0 0 0 d0 d1
^^^^^^^
Notice the 4 bytes of 0 before the expected byte of d0.
Databook notes that the RX buffer must be a multiple of 4/8/16
bytes [1].
Update the DMA Buffer size define to 8188 instead of 8192. Remove
the -1 from the RX buffer size allocations and use the new
DMA Buffer size directly.
[1] Synopsys DesignWare Cores Ethernet MAC Universal v3.70a
[section 8.4.2 - Table 8-24]
Tested on SoCFPGA Stratix10 with ping sweep from 100 to 8300 byte packets.
Fixes: 286a837217 ("stmmac: add CHAINED descriptor mode support (V4)")
Suggested-by: Jose Abreu <jose.abreu@synopsys.com>
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A stuck ramrod should be deleted from the completion_pending list,
otherwise it will be added again in the future and corrupt the list.
Return error value to inform that ramrod is stuck and should be deleted.
Signed-off-by: Sagiv Ozeri <sagiv.ozeri@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qed_sp_destroy_request() API was added for SPQ users that need to
free/return the entry they acquired in their error flows.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there are no SPQ entries left in the free_pool, new entries are
allocated and are added to the unlimited list. When an entry in the pool
is available, the content is copied from the original entry, and the new
entry is sent to the device. qed_spq_post() is not aware of that, so the
additional entry is stored in the original entry as p_post_ent, which can
later be returned to the pool.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
