Add i2c-thermtrip which would set the DEV_OFF bit in the DCDC control
register of the TPS65911 PMIC.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Clean-up pinmuxing:
- white-space clean-up
- explicitly disable input of BKL1_ON, BKL1_PWM and BKL1_PWM_EN#
- annotate Apalis I2C3 usage for CAM
- get rid of nvidia,lock property
- add missing eMMC sdmmc4_cmd_pt7 and explicitly enable input
- explicitly disable lcd_dc1_pd2 (e.g. LM95245 I2C address pin)
- annotate TOUCH_PEN_INT# being on-module
- As underscores in node names are not recommended replace them all
where possible with dashes.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Annotate UARTs and move the serial UART "nvidia,tegra30-hsuart"
compatible definitions from the carrier board to the module level device
trees. One could still override this in a custom carrier board device
tree if required.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Annotate PCIe port nodes and clean-up PCIe controller/port status' with
respect to carrier board vs. module level device trees. As port 3
connects to the on-module Gigabit Ethernet MACPHY it is always enabled
together with the PCIe controller itself.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to avoid any floating SD card detect pins as may e.g. happen on
Ixora V1.1A pull them all up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is similar to tegra124 and avoids the following being reported
upon boot:
hw perfevents: no interrupt-affinity property for /pmu, guessing.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the actual dts for the tinker board S, which brings its own emmc
device, not therefore not requiring an sd-card to boot.
Signed-off-by: David Summers <beagleboard@davidjohnsummers.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tinker Board and Tinker Board S share most of their components,
so should also not replicate these for each variant.
So move them to a shared dtsi that then can get included by both
boards.
Signed-off-by: David Summers <beagleboard@davidjohnsummers.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On the imx6qdl-zii-rdu2 board the RTC functionality is provided via
a DS1341 RTC connected via I2C bus, so we can safely disable the internal
one.
Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to Documentation/devicetree/bindings/rtc/rtc-ds1307.txt the
original compatible "maxim,ds1341" is not a valid entry.
Switch to the documented "dallas,ds1341" compatible.
Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6UL, accessing OCOTP directly is wrong because the ocotp clock
needs to be enabled first, so use the nvmem-cells binding instead.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dtc has new checks for SPI buses. Fix the warnings in node names and
unit-addresses.
There's over 100 warnings for FSL boards, a few examples:
arch/arm/boot/dts/imx28-duckbill-2-spi.dtb: Warning (spi_bus_bridge): /apb@80000000/apbh@80000000/ssp@80014000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/imx53-ppd.dtb: Warning (spi_bus_bridge): /soc/aips@50000000/spba@50000000/ecspi@50010000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/imx6dl-colibri-eval-v3.dtb: Warning (spi_bus_reg): /soc/aips-bus@2000000/spba-bus@2000000/spi@2014000/mcp251x@1: SPI bus unit address format error, expected "0"
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To use the "earlycon" kernel command line parameter (without arguments)
we need a stdout-path property under the /chosen node. Add this to make
it easier to spot errors early in the boot process when looking for
them.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Odroid-C1 exposes ADC channels 0 and 1 on the GPIO headers. NOTE: Due
to the SoC design these are limited to 1.8V (instead of 3.3V like all
other pins).
Enable the SAR ADC to enable voltage measurements on these pins.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There are multiple fixed regulators on the Odroid-C1 board. Add them so
they can be used when we add the devices that need them (SAR ADC needs
the 1.8V IOREF, RTC needs VDD_RTC).
These are:
- P5V0 is the main 5V power input
- VCC3V3 / VDDIO_AO3V3 / VDD3V3: fixed regulator with 3.3V output which
is supplied by P5V0
- IOREF_1V8 / VCC1V8 / VDD1V8: fixed regulator with 1.8V output which is
supplied by P5V0
- VDD_RTC: fixed voltage regulator with 0.9V output which is supplied by
VDDIO_AO3V3
- DDR_VDDC / DDR3_1V5: fixed voltage regulator with 1.5V output which is
supplied by P5V0
- the existing TF_IO and RFLASH_VDD_EN regulators are supplied by
VDDIO_AO3V3
- the existing VCCK regulator is supplied by P5V0
This does not add the missing VDDEE regulator (controlled by PWM_D)
because it's not clear yet how to configure the voltage of that
regulator.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The CPU voltage regulator is a "Monolithic Power Systems MP2161"
(according to the Odroid-C1+'s schematics). It is driven by PWM_C on
GPIODV_9.
Hardkernel's 3.10 kernel (based on the Amlogic GPL kernel sources)
defines a PWM voltage table with the following values:
- 0.86 volts = PWM register value 0x10f001b
- (more values in 0.1 volt increments)
- 1.14 volts = PWM register value 0x000012a
When using the XTAL (24MHz) as input this translates into a PWM period
of 12218ns with 0.86V using a duty cycle of 91% and 1.14V using a duty
cycle of 0%.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Endless Mini (EC-100) is a grapefruit-sized computer based on the
Amlogic Meson8b (S805) SoC which comes in two variants.
Both variants have in common:
- Amlogic Meson8b (S805) SoC
- two USB 2.0 ports on the rear, one one the front (connected to the SoC
through an internal hub)
- 3.5mm Stereo out and MIC combo port
- HDMI and CVBS output
- 5V power supply (rated at 3A / 15W)
- an internal embedded micro-controller (called "EC") which implements a
"breathing" effect for the LED and allows shutting down (powering off)
the whole device
- 10/100 Mbit/s Ethernet using an IC Plus IP101A/G PHY (note: the website
incorrectly lists a Gigabit Ethernet port)
- the CPU voltage is regulated using a PWM regulator. The GPL sources of
the EC-100 are using a PWM value of 0x1c0000 for 0.86V and a PWM value
of 0x00001c for 1.14V. When using the XTAL (24MHz) as input this
translates into a PWM period of 1148ns with 0.86V using a duty cycle of
100% and 1.14V using a duty cycle of 0%.
The main differences are:
- the main indicator for the variant is the RAM size: the "cheaper"
variant has 1 GB of RAM, while the more expensive one comes with 2GB
- the storage size differs: 24 GB vs 32 GB
- the "1 GB RAM" variant has Ethernet connectivity only, while the "2 GB"
variant has a Realtek RTL8723BS SDIO chip which adds 802.11b/g/n wifi
and Bluetooth 4.0 support
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Some boards use an RMII Ethernet PHY which requires fewer pins than the
RGMII PHYs. Add a separate eth_rmii_pins node which does not include the
pins which are only required for RGMII (but not for RMII) PHYs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
These are used for example on the Endless Mini (EC-100):
- I2C_A is connected to the Realtek RT5640 audio codec
- PWM_C (GPIODV_9) is connected to a PWM regulator which is used for
VCCK (CPU voltage supply)
- UART_B is connected to the Bluetooth module (of the RTL8723BS SDIO
wifi and Bluetooth combo chip)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Remove unused parameter from SPI6 dmas property on stm32mp157c SoC.
Fixes: dc3f8c86c1 ("ARM: dts: stm32: add SPI support on stm32mp157c")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
[olof: Without this patch, SPI6 will fall back to interrupt mode with
lower perfmance]
Signed-off-by: Olof Johansson <olof@lixom.net>
imx51-zii-scu2-mezz has an external watchdog in the environment
microcontroller, so disable the internal one.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This pull request contains Broadcom ARM-based SoCs Device Tree changes
intended for 4.19, please pull the following:
- Florian fixes the PPI and SPI interrupts in the BCM63138 (DSL) SoC DTS
* tag 'arm-soc/for-4.19/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM63xx: Fix incorrect interrupt specifiers
Signed-off-by: Olof Johansson <olof@lixom.net>
Samsung DTS ARM changes for v4.20
1. Bring up DSI and HDMI on Exynos5250 Arndale.
2. Use the new way of setting external wakeup interrupts on S5Pv210.
3. Use proper cpufreq suspend OPP to fix suspend/wakeup from RAM on Snow
Chromebook (Exynos5250).
4. Fully describe regualtors on Odroid XU3-family boards.
5. Fix sound in Snow-rev5 Chromebook.
6. Fix regulators configuration on Peach Pi/Pit Chromebooks (Exynos5420)
which should be always on.
7. Fix pull control on PMIC interrupt lines on multiple boards which
essentially fixes waking up by RTC.
8. Add PMIC interrupts on Exynos4210 UniversalC210 board.
9. Add external SD card support for Trats board (Exynos4210).
10. Correct audio subsystem parent clock on Peach Chromebooks.
11. Minor cleanups.
* tag 'samsung-dt-4.20-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Correct audio subsystem parent clock on Peach Chromebooks
ARM: dts: exynos: Add external SD card support for Trats board
ARM: dts: exynos: Disable pull control for PMIC IRQ line on Artik5 board
ARM: dts: exynos: Disable pull control for S5M8767 PMIC
ARM: dts: exynos: Remove double SD card detect pin inversion
ARM: dts: exynos: Add missing PMIC interrupts on UniversalC210 board
ARM: dts: exynos: Disable pull control for MAX8997 interrupts on Origen
ARM: dts: exynos: Fix regulators configuration on Peach Pi/Pit Chromebooks
ARM: dts: exynos: Fix sound in Snow-rev5 Chromebook
ARM: dts: exynos: Add LDO28 regulator on Exynos5422 Odroid boards
ARM: dts: exynos: Disable unused PMIC regulators on Exynos5422 Odroid boards
ARM: dts: exynos: Add unused PMIC regulators on Exynos5422 Odroid boards
ARM: dts: exynos: Add missing used PMIC regulators on Exynos5422 Odroid boards
ARM: dts: exynos: Mark 1 GHz CPU OPP as suspend OPP on Exynos5250
ARM: dts: exynos: Convert exynos5250.dtsi to opp-v2 bindings
ARM: dts: s5pv210: Switch to S5Pv210 specific pinctrl wakeup compatible
ARM: dts: exynos: Fix HDMI-HPD line handling on Arndale
ARM: dts: exynos: Use i2c-gpio for HDMI-DDC on Arndale
ARM: dts: exynos: Add DSI and panel nodes on Arndale
ARM: dts: exynos: Add DSI node on Exynos5250
Signed-off-by: Olof Johansson <olof@lixom.net>
SoCFPGA DTS updates for v4.20, part 2
- Fix I2C bus unit-address warning with new DTC checks
- Add reset properties for timers
* tag 'socfpga_updates_for_v4.20_part2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: add timer resets for SoCFPGA platform
ARM: dts: socfpga: Fix I2C bus unit-address error
Signed-off-by: Olof Johansson <olof@lixom.net>
STi DT update:
_ Change syntax of multiple DAI links
* tag 'sti-dt-for-v4.20-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: stih410: change syntax of multiple DAI
Signed-off-by: Olof Johansson <olof@lixom.net>
AT91 DT for 4.20
- warning fiwes from Rob
- many updates for the axentia boards
- ADC, I2S and touch screen support for sama5d2
* tag 'at91-4.20-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
arm: dts: sama5d2: Update coresight bindings for hardware ports
ARM: dts: at91: sama5d27_som1_ek: add adc regulators
ARM: dts: atmel: Fix I2C and SPI bus warnings
ARM: dts: at91: sama5d4: add labels to soc dtsi for derivative boards
ARM: dts: at91: tse850: drop three indentation levels
ARM: dts: at91: nattis: drop three indentation levels
ARM: dts: at91: nattis: describe the lvds panel
ARM: dts: at91: nattis: move pinctrls for the lvds chip to the lvds node
ARM: dts: at91: nattis: state the actual lvds-encoder chip
ARM: dts: at91: nattis: make the SD-card slot work
ARM: dts: at91: nattis: set the PRLUD and HIPOW signals low
ARM: dts: at91/trivial: remove old NAND bindings leftover in sama5d2
ARM: dts: at91/trivial: Fix USART1 definition for at91sam9g45
ARM: dts: at91: sama5d2 Xplained: add pin muxing for I2S
ARM: dts: at91: sama5d2: add nodes for I2S controllers
ARM: dts: at91: sama5d2: add I2S clock muxing nodes
ARM: dts: at91: sama5d2: Add resistive touch device
ARM: dts: at91: sama5d2: add channel cells for ADC device
Signed-off-by: Olof Johansson <olof@lixom.net>
