Pull clk fixes from Stephen Boyd:
"A few clk driver fixes this time:
- Introduce protected-clock DT binding to fix breakage on qcom
sdm845-mtp boards where the qspi clks introduced this merge window
cause the firmware on those boards to take down the system if we
try to read the clk registers
- Fix a couple off-by-one errors found by Dan Carpenter
- Handle failure in zynq fixed factor clk driver to avoid using
uninitialized data"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: zynqmp: Off by one in zynqmp_is_valid_clock()
clk: mmp: Off by one in mmp_clk_add()
clk: mvebu: Off by one bugs in cp110_of_clk_get()
arm64: dts: qcom: sdm845-mtp: Mark protected gcc clocks
clk: qcom: Support 'protected-clocks' property
dt-bindings: clk: Introduce 'protected-clocks' property
clk: zynqmp: handle fixed factor param query error
Pull input updates from Dmitry Torokhov:
"Mostly new IDs for Elan/Synaptics touchpads, plus a few small fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: omap-keypad - fix keyboard debounce configuration
Input: xpad - quirk all PDP Xbox One gamepads
Input: synaptics - enable SMBus for HP 15-ay000
Input: synaptics - add PNP ID for ThinkPad P50 to SMBus
Input: elan_i2c - add ACPI ID for Lenovo IdeaPad 330-15ARR
Input: elan_i2c - add support for ELAN0621 touchpad
Input: hyper-v - fix wakeup from suspend-to-idle
Input: atkbd - clean up indentation issue
Input: st1232 - convert to SPDX identifiers
Input: migor_ts - convert to SPDX identifiers
Input: dt-bindings - fix a typo in file input-reset.txt
Input: cros_ec_keyb - fix button/switch capability reports
Input: elan_i2c - add ELAN0620 to the ACPI table
Input: matrix_keypad - check for errors from of_get_named_gpio()
Pull media fixes from Mauro Carvalho Chehab:
- Revert a dt-bindings patch whose driver didn't make for 4.20
- fix a kernel oops at vicodec driver
- fix a frame overflow at gspca with was causing regressions on some
cameras, making them to not work
- use the proper type for wait_queue head
- make media request API compatible with 32-bit userspace on 64-bit
kernel
- fix a regression on Kernel 4.19 at dvb-pll
- don't use SPDX headers yet for GFDL
* tag 'media/v4.20-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: mediactl docs: Fix licensing message
media: dvb-pll: don't re-validate tuner frequencies
media: dvb-pll: fix tuner frequency ranges
media: Revert "media: dt-bindings: Document the Rockchip VPU bindings"
media: gspca: fix frame overflow error
media: vicodec: fix memchr() kernel oops
media: cedrus: add action item to the TODO
media: media-request: Add compat ioctl
media: Use wait_queue_head_t for media_request
Pull USB/PHY driver fixes from Greg KH:
"Here are some small USB and PHY driver fixes for 4.20-rc5
Nothing big at all, just the usual handful of USB fixes for reported
issues, along with some gadget and PHY driver bug fixes.
All of these have been in linux-next with no reported issues. Note,
the USB gadget fixes were in linux-next on its own branch, not in
mine, it just got merged into here yesterday and missed linux-next of
today"
* tag 'usb-4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: u_ether: fix unsafe list iteration
USB: omap_udc: fix rejection of out transfers when DMA is used
USB: omap_udc: fix USB gadget functionality on Palm Tungsten E
USB: omap_udc: fix omap_udc_start() on 15xx machines
USB: omap_udc: fix crashes on probe error and module removal
USB: omap_udc: use devm_request_irq()
usb: core: quirks: add RESET_RESUME quirk for Cherry G230 Stream series
USB: usb-storage: Add new IDs to ums-realtek
Revert "usb: dwc3: gadget: skip Set/Clear Halt when invalid"
phy: qcom-qusb2: Fix HSTX_TRIM tuning with fused value for SDM845
phy: qcom-qusb2: Use HSTX_TRIM fused value as is
dt-bindings: phy-qcom-qmp: Fix several mistakes from prior commits
phy: uniphier-pcie: Depend on HAS_IOMEM
Pull spi fixes from Mark Brown:
"A few driver specific fixes here, nothing big or that stands out for
anyone other than the driver users.
The omap2-mcspi fix is for issues that started showing up with a
change in defconfig in this release to make cpuidle get turned on by
default"
* tag 'spi-fix-v4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: omap2-mcspi: Add missing suspend and resume calls
spi: mediatek: use correct mata->xfer_len when in fifo transfer
spi: uniphier: fix incorrect property items
Kishon writes:
phy: for 4.20-rc
*) Fix updating HSTX_TRIM tuning parameter in qcom-qusb2 PHY driver
*) Fix inconsistencies between dt-bindings and the driver
*) Add "Depend on HAS_IOMEM" uniphier-pcie to avoid randconfig errors
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-4.20-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: qcom-qusb2: Fix HSTX_TRIM tuning with fused value for SDM845
phy: qcom-qusb2: Use HSTX_TRIM fused value as is
dt-bindings: phy-qcom-qmp: Fix several mistakes from prior commits
phy: uniphier-pcie: Depend on HAS_IOMEM
This reverts commit e4183d3256.
The commit was picked by mistake, as the Rockchip VPU driver
is not ready for inclusion yet, and it's still under discussion.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a generic clk property for clks which are not intended to be used by
the OS due to security restrictions put in place by firmware. For
example, on some Qualcomm firmwares reading or writing certain clk
registers causes the entire system to reboot, but on other firmwares
reading and writing those same registers is required to make devices
like QSPI work. Rather than adding one-off properties each time a new
set of clks appears to be protected, let's add a generic clk property to
describe any set of clks that shouldn't be touched by the OS. This way
we never need to register the clks or use them in certain firmware
configurations.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Pull networking fixes from David Miller:
1) Fix some potentially uninitialized variables and use-after-free in
kvaser_usb can drier, from Jimmy Assarsson.
2) Fix leaks in qed driver, from Denis Bolotin.
3) Socket leak in l2tp, from Xin Long.
4) RSS context allocation fix in bnxt_en from Michael Chan.
5) Fix cxgb4 build errors, from Ganesh Goudar.
6) Route leaks in ipv6 when removing exceptions, from Xin Long.
7) Memory leak in IDR allocation handling of act_pedit, from Davide
Caratti.
8) Use-after-free of bridge vlan stats, from Nikolay Aleksandrov.
9) When MTU is locked, do not force DF bit on ipv4 tunnels. From
Sabrina Dubroca.
10) When NAPI cached skb is reused, we must set it to the proper initial
state which includes skb->pkt_type. From Eric Dumazet.
11) Lockdep and non-linear SKB handling fix in tipc from Jon Maloy.
12) Set RX queue properly in various tuntap receive paths, from Matthew
Cover.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tuntap: fix multiqueue rx
ipv6: Fix PMTU updates for UDP/raw sockets in presence of VRF
tipc: don't assume linear buffer when reading ancillary data
tipc: fix lockdep warning when reinitilaizing sockets
net-gro: reset skb->pkt_type in napi_reuse_skb()
tc-testing: tdc.py: Guard against lack of returncode in executed command
tc-testing: tdc.py: ignore errors when decoding stdout/stderr
ip_tunnel: don't force DF when MTU is locked
MAINTAINERS: Add entry for CAKE qdisc
net: bridge: fix vlan stats use-after-free on destruction
socket: do a generic_file_splice_read when proto_ops has no splice_read
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
Revert "net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs"
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
net/sched: act_pedit: fix memory leak when IDR allocation fails
net: lantiq: Fix returned value in case of error in 'xrx200_probe()'
ipv6: fix a dst leak when removing its exception
net: mvneta: Don't advertise 2.5G modes
drivers/net/ethernet/qlogic/qed/qed_rdma.h: fix typo
net/mlx4: Fix UBSAN warning of signed integer overflow
...
Pull power management fixes from Rafael Wysocki:
"These remove a stale DT entry left behind after recent removal of a
cpufreq driver without users, fix up error handling in the imx6q
cpufreq driver, fix two issues in the cpufreq documentation, and
update the ARM cpufreq driver.
Specifics:
- Drop stale DT binding for the arm_big_little_dt driver removed
recently (Sudeep Holla).
- Fix up error handling in the imx6q cpufreq driver to make it report
voltage scaling failures (Anson Huang).
- Fix two issues in the cpufreq documentation (Viresh Kumar, Zhao Wei
Liew).
- Fix ARM cpuidle driver initialization regression from the 4.19 time
frame and rework the driver registration part of it to simplify
code (Ulf Hansson)"
* tag 'pm-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ARM: cpuidle: Convert to use cpuidle_register|unregister()
ARM: cpuidle: Don't register the driver when back-end init returns -ENXIO
dt-bindings: cpufreq: remove stale arm_big_little_dt entry
Documentation: cpufreq: Correct a typo
cpufreq: imx6q: add return value check for voltage scale
Documentation: cpu-freq: Frequencies aren't always sorted
Marc Kleine-Budde says:
====================
pull-request: can 2018-11-09
this is a pull request of 20 patches for net/master.
First we have a patch by Oliver Hartkopp which changes the raw socket's
raw_sendmsg() to return an error value if the user tries to send a CANFD
frame to a CAN-2.0 device.
The next two patches are by Jimmy Assarsson and fix potential problems
in the kvaser_usb driver.
YueHaibing's patches for the ucan driver fix a compile time warning and
remove a duplicate include.
Eugeniu Rosca patch adds more binding documentation to the rcar_can
driver bindings. The next two patches are by Fabrizio Castro for the
rcar_can driver and fixes a problem in the driver's probe function and
document the r8a774a1 binding.
Lukas Wunner's patch fixes a recpetion problem in hi311x driver by
switching from edge to level triggered interruts.
The next three patches all target the flexcan driver. Pankaj Bansal's
patch unconditionally unlocks the last mailbox used for RX. Alexander
Stein provides a better workaround for a hardware limitation when
sending RTR frames, by using the last mailbox for TX, resulting in fewer
lost frames. The patch by me simplyfies the driver, by making a runtime
value a compile time constant.
The following 4 patches are by me and provide the groundwork for the
next patches by Oleksij Rempel. To avoid code duplication common code in
the common CAN driver infrastructure is factured out and error handling
is cleaned up.
The next 4 patches are by Oleksij Rempel and fix the problem in the
flexcan driver that other processes see TX frames arrive out of order
with ragards to a RX'ed frame (which are send by a different system on
the CAN bus as the result of our TX frame).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Digging through the "phy-qcom-qmp" showed me many inconsistencies
between the bindings and the reality of the driver. Let's fix them
all.
* In commit 2d66eab183 ("dt-bindings: phy: qmp: Add support for QMP
phy in IPQ8074") we probably should have explicitly listed that
there are no clocks for this PHY and also added the reset names in
alphabetical order. You can see that there are no clocks in the
driver where "clk_list" is NULL.
* In commit 8587b220f0 ("dt-bindings: phy-qcom-qmp: Update bindings
for QMP V3 USB PHY") we probably should have listed the resets for
this new PHY and also removed the "(Optional)" marking for the "cfg"
reset since PHYs that need "cfg" really do need it. It's just that
not all PHYs need it.
* In commit 7f08020741 ("dt-bindings: phy-qcom-qmp: Update bindings
for sdm845") we forgot to update one instance of the string
"qcom,qmp-v3-usb3-phy" to be "qcom,sdm845-qmp-usb3-phy". Let's fix
that. We should also have added "qcom,sdm845-qmp-usb3-uni-phy" to
the clock-names and reset-names lists.
* In commit 99c7c7364b ("dt-bindings: phy-qcom-qmp: Add UFS phy
compatible string for sdm845") we should have added the set of
clocks and resets for "qcom,sdm845-qmp-ufs-phy". These were taken
from the driver.
* Cleanup the wording for what properties child nodes have to make it
more obvious which types of PHYs need clocks and resets. This was
sorta implicit in the "-names" description but I found myself
confused.
* As per the code not all "pcie qmp phys" have resets. Specifically
note that the "has_lane_rst" property in the driver is false for
"ipq8074-qmp-pcie-phy". Thus make it clear exactly which PHYs need
child nodes with resets.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Pull i2c updates from Wolfram Sang:
"I2C has one bugfix (qcom-geni driver), one arch enablement (i2c-omap
driver, no code change), and a new driver (nvidia-gpu) this time"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
usb: typec: ucsi: add support for Cypress CCGx
i2c: nvidia-gpu: make pm_ops static
i2c: add i2c bus driver for NVIDIA GPU
i2c: qcom-geni: Fix runtime PM mismatch with child devices
MAINTAINERS: Add entry for i2c-omap driver
i2c: omap: Enable for ARCH_K3
dt-bindings: i2c: omap: Add new compatible for AM654 SoCs
AM654 SoCs have same I2C IP as OMAP SoCs. Add new compatible to
handle AM654 SoCs. While at that reformat the existing compatible list
for older SoCs to list one valid compatible per line.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the hi3110 shares the SPI bus with another traffic-intensive device
and packets are received in high volume (by a separate machine sending
with "cangen -g 0 -i -x"), reception stops after a few minutes and the
counter in /proc/interrupts stops incrementing. Bus state is "active".
Bringing the interface down and back up reconvenes the reception. The
issue is not observed when the hi3110 is the sole device on the SPI bus.
Using a level-triggered interrupt makes the issue go away and lets the
hi3110 successfully receive 2 GByte over the course of 5 days while a
ks8851 Ethernet chip on the same SPI bus handles 6 GByte of traffic.
Unfortunately the hi3110 datasheet is mum on the trigger type. The pin
description on page 3 only specifies the polarity (active high):
http://www.holtic.com/documents/371-hi-3110_v-rev-kpdf.do
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Most of the ARM platforms used v2 OPP bindings to support big-little
configurations. This arm_big_little_dt binding is incomplete and was
never used.
Commit f174e49e49 (cpufreq: remove unused arm_big_little_dt driver)
removed the driver supporting this binding, but the binding was left
unnoticed, so let's get rid of it now.
Fixes: f174e49e49 (cpufreq: remove unused arm_big_little_dt driver)
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull more timer updates from Thomas Gleixner:
"A set of commits for the new C-SKY architecture timers"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dt-bindings: timer: gx6605s SOC timer
clocksource/drivers/c-sky: Add gx6605s SOC system timer
dt-bindings: timer: C-SKY Multi-processor timer
clocksource/drivers/c-sky: Add C-SKY SMP timer
Pull pwm updates from Thierry Reding:
"This series contains a number of improvements to existing drivers,
such as LPSS. Some drivers, such as renesas-tpu and rcar get support
for more SoC generations. To round things off this fixes an issue with
the sysfs interface"
* tag 'pwm/for-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: lpss: Only set update bit if we are actually changing the settings
pwm: lpss: Force runtime-resume on suspend on Cherry Trail
pwm: Enable TI ECAP driver for ARCH_K3
dt-bindings: pwm: tiecap: Add TI AM654 SoC specific compatible
dt-bindings: pwm: rcar: Add r8a774a1 support
pwm: Send a uevent on the pwmchip device upon channel sysfs (un)export
Revert "pwm: Set class for exported channels in sysfs"
dt-bindings: pwm: renesas-tpu: Document r8a7744 support
dt-bindings: pwm: rcar: Add r8a7744 support
dt-bindings: pwm: renesas: tpu: Document R8A779{7|8}0 bindings
dt-bindings: pwm: renesas: pwm-rcar: Document R8A779{7|8}0 bindings
dt-bindings: pwm: renesas: tpu: Fix "compatible" prop description
pwm: Use SPDX identifier for Renesas drivers
pwm: lpss: Add get_state callback
pwm: lpss: Release runtime-pm reference from the driver's remove callback
pwm: lpss: Check PWM powerstate after resume on Cherry Trail devices
pwm: lpss: Move struct pwm_lpss_chip definition to the header file
pwm: lpss: Add ACPI HID for second PWM controller on Cherry Trail devices
ACPI / PM: Export acpi_device_get_power() for use by modular build drivers
pwm: tegra: Remove gratuituous blank line
Pull drm fixes from Dave Airlie:
"Pretty much a normal fixes pull pre-rc1, mostly amdgpu fixes, one i915
link training regression fix, and a couple of minor panel/bridge fixes
and a panel quirk"
* tag 'drm-next-2018-11-02' of git://anongit.freedesktop.org/drm/drm: (37 commits)
drm/amdgpu: revert "enable gfxoff in non-sriov and stutter mode by default"
drm/amd/pp: Print warning if od_sclk/mclk out of range
drm/amd/pp: Fix pp_sclk/mclk_od not work on Vega10
drm/amd/pp: Fix pp_sclk/mclk_od not work on smu7
drm/amd/powerplay: no MGPU fan boost enablement on DPM disabled
drm/amdgpu: Fix skipping hangged job reset during gpu recover.
drm/amd/powerplay: revise Vega20 pptable version check
drm/amd/display: set backlight level limit to 1
drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1
dt-bindings: drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1
drm/bridge: ti-sn65dsi86: Remove the mystery delay
drm/panel: simple: Add "no-hpd" delay for Innolux TV123WAM
drm/panel: simple: Support panels with HPD where HPD isn't connected
dt-bindings: drm/panel: simple: Add no-hpd property
drm/edid: Add 6 bpc quirk for BOE panel.
drm/amdgpu: fix reporting of failed msg sent to SMU (v2)
drm/amdgpu: Fix compute ring 1.0.0 failure after reset
drm/amdgpu: fix VM leaf walking
drm/amdgpu: fix amdgpu_vm_fini
drm/amd/powerplay: commonize the API for retrieving current clocks
...
Pull Devicetree fixes from Rob Herring:
- fix cpu node iterator for powerpc systems
- clarify ARM CPU binding 'capacities-dmips-mhz' property calculations
* tag 'devicetree-fixes-for-4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: Fix cpu node iterator to not ignore disabled cpu nodes
dt-bindings: arm: Explain capacities-dmips-mhz calculations in example
Pull clk updates from Stephen Boyd:
"This time it looks like a quieter release cycle in the clk tree. I
guess that's because of summer time holidays/vacations. The biggest
change in the diffstat is in the Qualcomm clk driver, where they got
support for CPUs and handful of SoCs. After that, the at91 driver got
a major rewrite for newer DT bindings that should make things easier
going forward and the TI code moved to a clockdomain based design.
The long tail is mostly small driver updates for newer clks and some
simpler SoC clock drivers such as the Hisilicon and imx support.
In the core framework, we only have two small changes this time.
One is a new clk API to get all clks for a device with the bulk clk
APIs. This allows drivers that don't care about doing anything besides
turning on all the clks to just clk_get() them all and turn them on.
The other change is the beginning of a way to support save and restore
of clk settings in the clk framework. TI is the only user right now,
but we will want to expand upon this design in the future to support
more save and restore of clk registers. At least this gets us started
and works well enough for one SoC, but there's more work in the
future.
Core:
- clk_bulk_get_all() API and friends to get all the clks for a device
- Basic clk state save/restore hooks
New Drivers:
- Renesas RZ/A2 (R7S9210) SoC, including early clocks
- Rensas RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs
- Rensas RZ/G2M (r8a774a1) SoC
- Qualcomm Krait CPU clk support
- Qualcomm QCS404 GCC support
- Qualcomm SDM660 GCC support
- Qualcomm SDM845 camera clock controller
- Ingenic jz4725b CGU
- Hisilicon 3670 SoC support
- TI SCI clks on K3 SoCs
- iMX6 MMDC clks
- Reset Controller (RMU) support for Actions Semi Owl S900 and S700 SoCs
Updates:
- Rework at91 PMC clock driver for new DT bindings
- Nvidia Tegra clk driver MBIST workaround fix
- S2RAM support for Marvell mvebu periph clks
- Use updated printk format for OF node names
- Fix TI code to only search DT subnodes
- Various static analysis finds
- Tag various drivers with SPDX license tags
- Support dynamic frequency switching (DFS) on qcom SDM845 GCC
- Only use s2mps11 dt-binding defines instead of redefining them in the driver
- Add some more missing clks to qcom MSM8996 GCC
- Quad SPI clks on qcom SDM845
- Add support for CMT timer clocks on R-Car V3H
- Add support for SHDI and various timer clocks on R-Car V3M
- Improve OSC and RCLK (watchdog) handling on R-Car Gen3 SoCs
- Amlogic clk-pll driver improvements and updates
- Amlogic axg audio controller system clocks
- Register Amlogic meson8b clock controller early
- Add support for SATA and Fine Display Processor (FDP) clocks on R-Car M3-N
- Consolidation of system suspend related code in Exynos, S5P, S3C SoC clk drivers
- Fixes for system suspend support on Exynos542x (Odroid boards) and Exynos5433 SoC
- Remove obsoleted Exynos4212 ISP clock definitions
- Migrated TI am3/4/5 and dra7 SoCs to clockdomain based design
- TI RTC+DDR sleep mode support for clock save/restore
- Allwinner A64 display engine support and fixes
- Allwinner A83t display engine support and fixes"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (186 commits)
clk: qcom: Remove unused arrays in SDM845 GCC
clk: fixed-rate: fix of_node_get-put imbalance
clk: s2mps11: Add used attribute to s2mps11_dt_match
clk: qcom: gcc-sdm660: Add MODULE_LICENSE
clk: qcom: Add safe switch hook for krait mux clocks
dt-bindings: clock: Document qcom,krait-cc
clk: qcom: Add Krait clock controller driver
dt-bindings: arm: Document qcom,kpss-gcc
clk: qcom: Add KPSS ACC/GCC driver
clk: qcom: Add support for Krait clocks
clk: qcom: Add IPQ806X's HFPLLs
clk: qcom: Add MSM8960/APQ8064's HFPLLs
dt-bindings: clock: Document qcom,hfpll
clk: qcom: Add HFPLL driver
clk: qcom: Add support for High-Frequency PLLs (HFPLLs)
ARM: Add Krait L2 register accessor functions
clk: imx6q: add mmdc0 ipg clock
clk: imx6sl: add mmdc ipg clocks
clk: imx6sll: add mmdc1 ipg clock
clk: imx6sx: add mmdc1 ipg clock
...
Pull new experimental media request API from Mauro Carvalho Chehab:
"A new media request API
This API is needed to support device drivers that can dynamically
change their parameters for each new frame. The latest versions of
Google camera and codec HAL depends on such feature.
At this stage, it supports only stateless codecs.
It has been discussed for a long time (at least over the last 3-4
years), and we finally reached to something that seem to work.
This series contain both the API and core changes required to support
it and a new m2m decoder driver (cedrus).
As the current API is still experimental, the only real driver using
it (cedrus) was added at staging[1]. We intend to keep it there for a
while, in order to test the API. Only when we're sure that this API
works for other cases (like encoders), we'll move this driver out of
staging and set the API into a stone.
[1] We added support for the vivid virtual driver (used only for
testing) to it too, as it makes easier to test the API for the ones
that don't have the cedrus hardware"
* tag 'media/v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (53 commits)
media: dt-bindings: Document the Rockchip VPU bindings
media: platform: Add Cedrus VPU decoder driver
media: dt-bindings: media: Document bindings for the Cedrus VPU driver
media: v4l: Add definition for the Sunxi tiled NV12 format
media: v4l: Add definitions for MPEG-2 slice format and metadata
media: videobuf2-core: Rework and rename helper for request buffer count
media: v4l2-ctrls.c: initialize an error return code with zero
media: v4l2-compat-ioctl32.c: add missing documentation for a field
media: media-request: update documentation
media: media-request: EPERM -> EACCES/EBUSY
media: v4l2-ctrls: improve media_request_(un)lock_for_update
media: v4l2-ctrls: use media_request_(un)lock_for_access
media: media-request: add media_request_(un)lock_for_access
media: vb2: set reqbufs/create_bufs capabilities
media: videodev2.h: add new capabilities for buffer types
media: buffer.rst: only set V4L2_BUF_FLAG_REQUEST_FD for QBUF
media: v4l2-ctrls: return -EACCES if request wasn't completed
media: media-request: return -EINVAL for invalid request_fds
media: vivid: add request support
media: vivid: add mc
...
The example contains two values for the capacity currently, 446 in text
and 578 in code. The numbers are all correct but can confuse some of the
readers. This patch tries to explain how the numbers are calculated to
avoid same confusion going forward.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Pull remoteproc updates from Bjorn Andersson:
"This contains a series of patches that reworks the memory carveout
handling in remoteproc, in order to allow this to be reused for
statically allocated memory regions to be used for e.g. firmware.
It adds support for audio DSP (both TZ-assisted and non-TZ assisted)
and compute DSP on Qualcomm SDM845, TZ-assisted audio DSP, compute DSP
and WiFi processor on Qualcomm QCS404 and through some renaming of the
drivers cleans up the naming situation.
Finally support for custom coreudmp segment handlers is added and is
used in the Qualcomm modem remoteproc driver to gather memory dumps of
the firmware"
* tag 'rproc-v4.20' of git://github.com/andersson/remoteproc: (36 commits)
remoteproc: qcom: q6v5-mss: Register segments/dumpfn for coredump
remoteproc: qcom: q6v5-mss: Add custom dump function for modem
remoteproc: qcom: q6v5-mss: Refactor mba load/unload sequence
remoteproc: Add mechanism for custom dump function assignment
remoteproc: Introduce custom dump function for each remoteproc segment
remoteproc: modify vring allocation to rely on centralized carveout allocator
remoteproc: qcom: q6v5: shore up resource probe handling
remoteproc: qcom: qcom_q6v5_adsp: Fix some return value check
remoteproc: modify rproc_handle_carveout to support pre-registered region
remoteproc: add helper function to check carveout device address
remoteproc: add helper function to allocate rproc_mem_entry from reserved memory
remoteproc: add alloc ops in rproc_mem_entry struct
remoteproc: introduce rproc_find_carveout_by_name function
remoteproc: introduce rproc_add_carveout function
remoteproc: add helper function to allocate and init rproc_mem_entry struct
remoteproc: add name in rproc_mem_entry struct
remoteproc: add release ops in rproc_mem_entry struct
remoteproc: add rproc_va_to_pa function
remoteproc: configure IOMMU only if device address requested
remoteproc: qcom: q6v5-mss: add SCM probe dependency
...
Pull ARM SoC platform updates from Arnd Bergmann:
"A couple of platforms change hands in the MAINTAINERS file:
- Linus Walleij lists himself for the ARM Reference platforms:
versatile, vexpress, integrator and realview. He has been the main
contributor for these for a while, and makes it official now.
- Vladimir Zapolskiy takes over the LPC18xx platform from Joachim
Eastwood
- Manivannan Sadhasivam becomes a secondary maintainer for the
Actions Semi machines
- Nicolas Ferre lists updates the MAINTAINER listing for the AT91
platform: Ludovic Desroches is now a co-maintainer for the
platform, and several other people (Claudiu Beznea, Cristian
Birsan, Eugen Hristev, Codrin Ciubotariu) take over individual
device drivers.
Thanks everyone for working on this, and welcome to the new
maintainers!
The "virt" platform on qemy or kvm can now be used in big-endian mode
without additional tricks, thanks to Jason Donenfeld.
Once again, we gain support for another NXP i.MX6 variant, this time
it's the i.MX 6ULZ 32-bit single-core version.
On arm64, we add support for two SoCs from Renesas: RZ/G2E (r8a774c0)
and RZ/G2M (r8a774a1). These are described as microcontrollers on the
manufacturer website, but appear to be rather powerful. The RZ/G2M is
used on the reference board for the CIP Super Long Term Support (SLTS)
Linux Kernels"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
MAINTAINERS: Assign myself as a maintainer of ARM/LPC18XX architecture
arm64: exynos: Enable generic power domain support
MAINTAINERS: remove non-exsiting email address of Baoyou
MAINTAINERS: fix pattern in ARM/Synaptics berlin SoC section
MAINTAINERS: Drop dt-bindings/genpd/k2g.h
ARM: samsung: Limit SAMSUNG_PM_CHECK config option to non-Exynos platforms
arm64: actions: Enable PINCTRL in platforms Kconfig
MAINTAINERS: Add entry for Actions Semi Owl SoCs DMA driver
MAINTAINERS: Add entry for Actions Semiconductor Owl I2C driver
MAINTAINERS: Update clock binding entry for Actions Semi Owl SoCs
ARM: imx: add i.mx6ulz msl support
ARM: Assume maintainership of ARM reference designs
ARM: support big-endian for the virt architecture
MAINTAINERS: sdhci: move the Microchip entry to proper location
MAINTAINERS: move former ATMEL entries to proper MICROCHIP location
MAINTAINERS: remove the / ATMEL string from MICROCHIP entries
MAINTAINERS: iio: add co-maintainer to SAMA5D2-compatible ADC driver
MAINTAINERS: pwm: add entry for Microchip pwm driver
MAINTAINERS: dmaengine: add files to Microchip dma entry
MAINTAINERS: USB: change maintainer for Microchip USBA gadget driver
...
Pull ARM SoC driver updates from Arnd Bergmann:
"The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl"
interface that was a little controversial at first, but the version
we merged solved that by not exposing arbitrary firmware calls to
user space.
- The Amlogic Meson platform gains a "canvas" driver that is used for
video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for their
respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in
particular a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem" device
driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (129 commits)
firmware: tegra: bpmp: Implement suspend/resume support
drivers: clk: Add ZynqMP clock driver
dt-bindings: clock: Add bindings for ZynqMP clock driver
firmware: xilinx: Add zynqmp IOCTL API for device control
Documentation: xilinx: Add documentation for eemi APIs
MAINTAINERS: imx: include drivers/firmware/imx path
firmware: imx: add misc svc support
firmware: imx: add SCU firmware driver support
reset: Fix potential use-after-free in __of_reset_control_get()
dt-bindings: arm: fsl: add scu binding doc
soc: fsl: qbman: add interrupt coalesce changing APIs
soc: fsl: bman_portals: defer probe after bman's probe
soc: fsl: qbman: Use last response to determine valid bit
soc: fsl: qbman: Add 64 bit DMA addressing requirement to QBMan
soc: fsl: qbman: replace CPU 0 with any online CPU in hotplug handlers
soc: fsl: qbman: Check if CPU is offline when initializing portals
reset: qcom: PDC Global (Power Domain Controller) reset controller
dt-bindings: reset: Add PDC Global binding for SDM845 SoCs
reset: Grammar s/more then once/more than once/
bus: ti-sysc: Just use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
...
Pull ARM SoC device tree updates from Arnd Bergmann:
"There are close to 800 indivudal changesets in this branch again,
which feels like a lot. There are particularly many changes for the
NVIDIA Tegra platform this time, in fact more than it has seen in the
two years since the v4.9 merge window. Aside from this, it's been
fairly normal, with lots of changes going into Renesas R-CAR, NXP
i.MX, Allwinner Sunxi, Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5 is a
minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core Marvell Armada 8040
network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in the
BMC.
NXP i.MX usually sees a lot of new boards each release. This time
there we only add one minor variant: ConnectCore 6UL SBC Pro uses the
same SoM design as the ConnectCore 6UL SBC Express added later.
However, there is a new chip, the i.MX6ULZ, which is an even smaller
variant of the i.MX6ULL, with features removed. There is also support
for the reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute
module based on bcm2837, it was launched in early 2017 but only now
added to the kernel, both as 32-bit and as 64-bit files, as we tend to
do for Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time are:
- Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
- Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
- Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
- Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana Pi
M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit Asus
Tinker board, the model 'S' based on rk3288, and three now boards
based on the popular RK3399 chip:
- ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
- Rock960: https://www.96boards.org/product/rock960/
- RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and the
RK3399 is the same chip used in several Chromebooks. Finally, we get
support for the PX30 (aka rk3326) chip, which is based on the low-end
64-bit Cortex-A35 CPU core. So far, only the evaluation board is
supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is
based on the MT7622 WiFi router platform, and the first product I've
seen with a 64-bit Mediatek chip in that market:
http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2), another
quad-core Cortex-A53 SoC, and its evaluation platform. On the 32-bit
side, we gain support for an actual end-user product, the Endless
Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform.
This chip is commonly known as the Snapdragon 835, and is used in
high-end phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the
previously added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the
M3NULCB Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing
files, the only board that gets added is the Toradex Colibri T20 on
Colibri Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the
(formerly Marvell) Berlin line of set-top-box chips used e.g. in the
various Google Chromecast. Only the .dtsi gets added at this point, no
actual machines"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (721 commits)
ARM: dts: socfgpa: remove ethernet aliases from dtsi
arm64: dts: stratix10: add ethernet aliases
dt-bindings: mediatek: Add bindig for MT7623 IOMMU and SMI
dt-bindings: mediatek: Add JPEG Decoder binding for MT7623
dt-bindings: iommu: mediatek: Add binding for MT7623
dt-bindings: clock: mediatek: add support for MT7623
ARM: dts: mvebu: armada-385-db-88f6820-amc: auto-detect nand ECC properites
ARM: dts: da850-lego-ev3: slow down A/DC as much as possible
ARM: dts: da850-evm: Enable tca6416 on baseboard
arm64: dts: uniphier: Add USB2 PHY nodes
arm64: dts: uniphier: Add USB3 controller nodes
ARM: dts: uniphier: Add USB2 PHY nodes
ARM: dts: uniphier: Add USB3 controller nodes
arm64: dts: meson-axg: s400: disable emmc
arm64: dts: meson-axg: s400: add missing emmc pwrseq
arm64: dts: clearfog-gt-8k: add PCIe slot description
ARM: dts: at91: sama5d4_xplained: even nand memory partitions
ARM: dts: at91: sama5d3_xplained: even nand memory partitions
ARM: dts: at91: at91sam9x5cm: even nand memory partitions
ARM: dts: at91: sama5d2_ptc_ek: fix bootloader env offsets
...
Pull i2c updates from Wolfram Sang:
"I2C has not so much stuff this time. Mostly driver enablement for new
SoCs, some driver bugfixes, and some cleanups"
* 'i2c/for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (35 commits)
MAINTAINERS: add maintainer for Renesas RIIC driver
i2c: sh_mobile: Remove dummy runtime PM callbacks
i2c: uniphier-f: fix race condition when IRQ is cleared
i2c: uniphier-f: fix occasional timeout error
i2c: uniphier-f: make driver robust against concurrency
i2c: i2c-qcom-geni: Simplify irq handler
i2c: i2c-qcom-geni: Simplify tx/rx functions
i2c: designware: Set IRQF_NO_SUSPEND flag for all BYT and CHT controllers
i2c: mux: mlxcpld: simplify code to reach the adapter
i2c: mux: ltc4306: simplify code to reach the adapter
i2c: mux: pca954x: simplify code to reach the adapter
i2c: core: remove level of indentation in i2c_transfer
i2c: core: remove outdated DEBUG output
i2c: zx2967: use core to detect 'no zero length' quirk
i2c: tegra: use core to detect 'no zero length' quirk
i2c: qup: use core to detect 'no zero length' quirk
i2c: omap: use core to detect 'no zero length' quirk
i2c: Convert to using %pOFn instead of device_node.name
i2c: brcmstb: Allow enabling the driver on DSL SoCs
eeprom: at24: fix unexpected timeout under high load
...
Pull media updates from Mauro Carvalho Chehab:
- new dvb frontend driver: lnbh29
- new sensor drivers: imx319 and imx 355
- some old soc_camera driver renames to avoid conflict with new
drivers
- new i.MX Pixel Pipeline (PXP) mem-to-mem platform driver
- a new V4L2 frontend for the FWHT codec
- several other improvements, bug fixes, code cleanups, etc
* tag 'media/v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (289 commits)
media: rename soc_camera I2C drivers
media: cec: forgot to cancel delayed work
media: vivid: Support 480p for webcam capture
media: v4l2-tpg: fix kernel oops when enabling HFLIP and OSD
media: vivid: Add 16-bit bayer to format list
media: v4l2-tpg-core: Add 16-bit bayer
media: pvrusb2: replace `printk` with `pr_*`
media: venus: vdec: fix decoded data size
media: cx231xx: fix potential sign-extension overflow on large shift
media: dt-bindings: media: rcar_vin: add device tree support for r8a7744
media: isif: fix a NULL pointer dereference bug
media: exynos4-is: make const array config_ids static
media: cx23885: make const array addr_list static
media: ivtv: make const array addr_list static
media: bttv-input: make const array addr_list static
media: cx18: Don't check for address of video_dev
media: dw9807-vcm: Fix probe error handling
media: dw9714: Remove useless error message
media: dw9714: Fix error handling in probe function
media: cec: name for RC passthrough device does not need 'RC for'
...
Pull tty/serial updates from Greg KH:
"Here is the big tty and serial pull request for 4.20-rc1
Lots of little things here, including a merge from the SPI tree in
order to keep things simpler for everyone to sync around for one
platform.
Major stuff is:
- tty buffer clearing after use
- atmel_serial fixes and additions
- xilinx uart driver updates
and of course, lots of tiny fixes and additions to individual serial
drivers.
All of these have been in linux-next with no reported issues for a
while"
* tag 'tty-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (66 commits)
of: base: Change logic in of_alias_get_alias_list()
of: base: Fix english spelling in of_alias_get_alias_list()
serial: sh-sci: do not warn if DMA transfers are not supported
serial: uartps: Do not allow use aliases >= MAX_UART_INSTANCES
tty: check name length in tty_find_polling_driver()
serial: sh-sci: Add r8a77990 support
tty: wipe buffer if not echoing data
tty: wipe buffer.
serial: fsl_lpuart: Remove the alias node dependence
TTY: sn_console: Replace spin_is_locked() with spin_trylock()
Revert "serial:serial_core: Allow use of CTS for PPS line discipline"
serial: 8250_uniphier: add auto-flow-control support
serial: 8250_uniphier: flatten probe function
serial: 8250_uniphier: remove unused "fifo-size" property
dt-bindings: serial: sh-sci: Document r8a7744 bindings
serial: uartps: Fix missing unlock on error in cdns_get_id()
tty/serial: atmel: add ISO7816 support
tty/serial_core: add ISO7816 infrastructure
serial:serial_core: Allow use of CTS for PPS line discipline
serial: docs: Fix filename for serial reference implementation
...
Pull staging/IIO driver updates from Greg KH:
"Here is the big staging and IIO driver pull request for 4.20-rc1.
There are lots of things here, we ended up adding more lines than
removing, thanks to a large influx of Comedi National Instrument
device support. Someday soon we need to get comedi out of staging...
Other than the comedi drivers, the "big" things here are:
- new iio drivers
- delete dgnc driver (no one used it and no one had the hardware
anymore)
- vbox driver updates and fixes
- erofs fixes
- tons and tons of tiny checkpatch fixes for almost all staging
drivers
All of these have been in linux-next, with the last few happening a
bit "late" due to them getting stuck on my laptop during travel to the
Mantainers summit"
* tag 'staging-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (690 commits)
staging: gasket: Fix sparse "incorrect type in assignment" warnings.
staging: gasket: remove debug logs for callback invocation
staging: gasket: remove debug logs in page table mapping calls
staging: rtl8188eu: core: Use sizeof(*p) instead of sizeof(struct P) for memory allocation
staging: ks7010: Remove extra blank line
staging: gasket: Remove extra blank line
staging: media: davinci_vpfe: Fix spelling mistake in enum
staging: speakup: Add a pair of braces
staging: wlan-ng: Replace long int with long
staging: MAINTAINERS: remove obsolete IPX staging directory
staging: MAINTAINERS: remove NCP filesystem entry
staging: rtl8188eu: cleanup comparsions to false
staging: gasket: Update device virtual address comment
staging: gasket: sysfs: fix attribute release comment
staging: gasket: apex: fix sysfs_show
staging: gasket: page_table: simplify gasket_components_to_dev_address
staging: gasket: page_table: fix comment in components_to_dev_address
staging: gasket: page table: fixup error path allocating coherent mem
staging: gasket: page_table: rearrange gasket_page_table_entry
staging: gasket: page_table: remove unnecessary PTE status set to free
...
Pull mailbox updates from Jassi Brar:
- convert print users to use the %pOFn format specifier
- enable ti-msgmr driver for the K3 platform as well
- add QCS404 to compatible list of QCOM's APCS IPC driver
- minor spelling fixes toogle -> toggle
- kzalloc failure catch in Mediatek driver
* tag 'mailbox-v4.20' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: mediatek: Add check for possible failure of kzalloc
mailbox: bcm-flexrm-mailbox: fix spelling mistake "toogle" -> "toggle"
mailbox: qcom: Add QCS404 APPS Global compatible
drivers: mailbox: Make ti-msgmr driver depend on ARCH_K3
mailbox: Convert to using %pOFn instead of device_node.name
As far as I can tell the bindings that were added in commit
9c04400f7e ("dt-bindings: drm/panel: Document Innolux TV123WAM panel
bindings") weren't actually for Innolux TV123WAM but were actually for
Innolux P120ZDG-BF1.
As far as I can tell the Innolux TV123WAM isn't a real panel and but
it's a mosh between the TI TV123WAM and the Innolux P120ZDG-BF1.
Let's unmosh.
Here's my evidence:
* Searching for TV123WAM on the Internet turns up a TI panel. While
it's possible that an Innolux panel has the same model number as the
TI Panel, it seems a little doubtful. Looking up the datasheet from
the TI Panel shows that it's 1920 x 1280 and 259.2 mm x 172.8 mm.
* As far as I know, the patch adding the Innolux Panel was supposed to
be for the board that's sitting in front of me as I type this
(support for that board is not yet upstream). On the back of that
panel I see Innolux P120ZDZ-EZ1 rev B1.
* Someone pointed me at a datasheet that's supposed to be for the
panel in front of me (sorry, I can't share the datasheet). That
datasheet has the string "p120zdg-bf1"
* If I search for "P120ZDG-BF1" on the Internet I get hits for panels
that are 2160x1440. They don't have datasheets, but the fact that
the resolution matches is a good sign.
While we doing the rename, also mention that no-hpd can be used with
this panel. See the previous patch in this series ("drm/panel:
simple: Add "no-hpd" delay for Innolux TV123WAM").
Fixes: 9c04400f7e ("dt-bindings: drm/panel: Document Innolux TV123WAM panel bindings")
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-5-dianders@chromium.org
Some eDP panels that are designed to be always connected to a board
use their HPD signal to signal that they've finished powering on and
they're ready to be talked to.
However, for various reasons it's possible that the HPD signal from
the panel isn't actually hooked up. In the case where the HPD isn't
hooked up you can look at the timing diagram on the panel datasheet
and insert a delay for the maximum amount of time that the HPD might
take to come up.
Let's add a property in the device tree for this concept.
Reviewed-by: Sean Paul <sean@poorly.run>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-1-dianders@chromium.org
Pull C-SKY architecture port from Guo Ren:
"This contains the Linux port for C-SKY(csky) based on linux-4.19
Release, which has been through 10 rounds of review on mailing list.
More information:
http://en.c-sky.com
The development repo:
https://github.com/c-sky/csky-linux
ABI Documentation:
https://github.com/c-sky/csky-doc
Here is the pre-built cross compiler for fast test from our CI:
https://gitlab.com/c-sky/buildroot/-/jobs/101608095/artifacts/file/output/images/csky_toolchain_qemu_csky_ck807f_4.18_glibc_defconfig_482b221e52908be1c9b2ccb444255e1562bb7025.tar.xz
We use buildroot as our CI-test enviornment. "LTP, Lmbench ..." will
be tested for every commit. See here for more details:
https://gitlab.com/c-sky/buildroot/pipelines
We'll continouslly improve csky subsystem in future"
Arnd acks, and adds the following notes:
"I did a thorough review of the ABI, which as usual mainly consists of
spotting any files that don't use the asm-generic ABI itself, and
having it changed to it matches exactly what we do on other new
architectures.
I also looked at every other patch and commented on maybe half of them
where I saw something that did not quite seem right. Others have
reviewed specific patches in greater depth. I'm sure that one could
fine more of the minor details, but as long as they are not ABI
relevant, they can be fixed later.
The only patch that is part of the ABI and that nobody reviewed is the
signal handling. This is one of the areas I never worked on in much
detail. I did not see anything wrong with it, but I also don't know
what the problems with the other architectures are here, and we seem
to be hitting issues occasionally, and we never managed to generalize
this enough for new architectures to have a trivial implementation.
I was originally hoping that we could have the 64-bit time_t
interfaces ready in time to completely drop the 32-bit ones, but that
did not happen. We might still remove them in the next merge window
depending on whether the libc upstream people prefer to keep them or
not.
One more general comment: I think this may well be the last new CPU
architecture we ever add to the kernel. Both nds32 and c-sky are made
by companies that also work on risc-v, and generally speaking risc-v
seems to be killing off any of the minor licensable instruction set
projects, just like ARM has mostly killed off the custom
vendor-specific instruction sets already.
If we add another architecture in the future, it may instead be
something like the LLVM bitcode or WebAssembly, who knows?"
To which Geert Uytterhoeven pipes in about another architecture still in
the pipeline: Kalray MPPA.
* tag 'csky-for-linus-4.20' of https://github.com/c-sky/csky-linux: (24 commits)
dt-bindings: interrupt-controller: C-SKY APB intc
irqchip: add C-SKY APB bus interrupt controller
dt-bindings: interrupt-controller: C-SKY SMP intc
irqchip: add C-SKY SMP interrupt controller
MAINTAINERS: Add csky
dt-bindings: Add vendor prefix for csky
dt-bindings: csky CPU Bindings
csky: Misc headers
csky: SMP support
csky: Debug and Ptrace GDB
csky: User access
csky: Library functions
csky: ELF and module probe
csky: Atomic operations
csky: IRQ handling
csky: VDSO and rt_sigreturn
csky: Process management and Signal
csky: MMU and page table management
csky: Cache and TLB routines
csky: System Call
...
Pull drm updates from Dave Airlie:
"This is going to rebuild more than drm as it adds a new helper to
list.h for doing bulk updates. Seemed like a reasonable addition to
me.
Otherwise the usual merge window stuff lots of i915 and amdgpu, not so
much nouveau, and piles of everything else.
Core:
- Adds a new list.h helper for doing bulk list updates for TTM.
- Don't leak fb address in smem_start to userspace (comes with EXPORT
workaround for people using mali out of tree hacks)
- udmabuf device to turn memfd regions into dma-buf
- Per-plane blend mode property
- ref/unref replacements with get/put
- fbdev conflicting framebuffers code cleaned up
- host-endian format variants
- panel orientation quirk for Acer One 10
bridge:
- TI SN65DSI86 chip support
vkms:
- GEM support.
- Cursor support
amdgpu:
- Merge amdkfd and amdgpu into one module
- CEC over DP AUX support
- Picasso APU support + VCN dynamic powergating
- Raven2 APU support
- Vega20 enablement + kfd support
- ACP powergating improvements
- ABGR/XBGR display support
- VCN jpeg support
- xGMI support
- DC i2c/aux cleanup
- Ycbcr 4:2:0 support
- GPUVM improvements
- Powerplay and powerplay endian fixes
- Display underflow fixes
vmwgfx:
- Move vmwgfx specific TTM code to vmwgfx
- Split out vmwgfx buffer/resource validation code
- Atomic operation rework
bochs:
- use more helpers
- format/byteorder improvements
qxl:
- use more helpers
i915:
- GGTT coherency getparam
- Turn off resource streamer API
- More Icelake enablement + DMC firmware
- Full PPGTT for Ivybridge, Haswell and Valleyview
- DDB distribution based on resolution
- Limited range DP display support
nouveau:
- CEC over DP AUX support
- Initial HDMI 2.0 support
virtio-gpu:
- vmap support for PRIME objects
tegra:
- Initial Tegra194 support
- DMA/IOMMU integration fixes
msm:
- a6xx perf improvements + clock prefix
- GPU preemption optimisations
- a6xx devfreq support
- cursor support
rockchip:
- PX30 support
- rgb output interface support
mediatek:
- HDMI output support on mt2701 and mt7623
rcar-du:
- Interlaced modes on Gen3
- LVDS on R8A77980
- D3 and E3 SoC support
hisilicon:
- misc fixes
mxsfb:
- runtime pm support
sun4i:
- R40 TCON support
- Allwinner A64 support
- R40 HDMI support
omapdrm:
- Driver rework changing display pipeline ordering to use common code
- DMM memory barrier and irq fixes
- Errata workarounds
exynos:
- out-bridge support for LVDS bridge driver
- Samsung 16x16 tiled format support
- Plane alpha and pixel blend mode support
tilcdc:
- suspend/resume update
mali-dp:
- misc updates"
* tag 'drm-next-2018-10-24' of git://anongit.freedesktop.org/drm/drm: (1382 commits)
firmware/dmc/icl: Add missing MODULE_FIRMWARE() for Icelake.
drm/i915/icl: Fix signal_levels
drm/i915/icl: Fix DDI/TC port clk_off bits
drm/i915/icl: create function to identify combophy port
drm/i915/gen9+: Fix initial readout for Y tiled framebuffers
drm/i915: Large page offsets for pread/pwrite
drm/i915/selftests: Disable shrinker across mmap-exhaustion
drm/i915/dp: Link train Fallback on eDP only if fallback link BW can fit panel's native mode
drm/i915: Fix intel_dp_mst_best_encoder()
drm/i915: Skip vcpi allocation for MSTB ports that are gone
drm/i915: Don't unset intel_connector->mst_port
drm/i915: Only reset seqno if actually idle
drm/i915: Use the correct crtc when sanitizing plane mapping
drm/i915: Restore vblank interrupts earlier
drm/i915: Check fb stride against plane max stride
drm/amdgpu/vcn:Fix uninitialized symbol error
drm: panel-orientation-quirks: Add quirk for Acer One 10 (S1003)
drm/amd/amdgpu: Fix debugfs error handling
drm/amdgpu: Update gc_9_0 golden settings.
drm/amd/powerplay: update PPtable with DC BTC and Tvr SocLimit fields
...
Pull watchdog updates from Wim Van Sebroeck:
- Add Armada 37xx CPU watchdog
- w83627hf_wdt: Add Support for NCT6796D, NCT6797D, NCT6798D
- hpwdt: several improvements
- renesas_wdt: SPDX identifiers, stop when unregistering, support for
R7S9210
- rza_wdt: SPDX identifiers, support longer timeouts
- core: fix null pointer dereference when releasing cdev
- iTCO_wdt: Drop option vendorsupport=2
- sama5d4: fix timeout-sec usage
- lantiq_wdt: convert to watchdog framework
- several small fixes
* tag 'linux-watchdog-4.20-rc1' of git://www.linux-watchdog.org/linux-watchdog: (30 commits)
watchdog: ts4800: release syscon device node in ts4800_wdt_probe()
watchdog: armada_37xx_wdt: use do_div for u64 division
documentation: watchdog: add documentation for armada-37xx-wdt
dt-bindings: watchdog: Document armada-37xx-wdt binding
watchdog: Add support for Armada 37xx CPU watchdog
dt-bindings: watchdog: add mpc8xxx-wdt support
watchdog: mpc8xxx: provide boot status
MAINTAINERS: Fix file pattern for MEN Z069 watchdog driver
dt-bindings: watchdog: renesas-wdt: Add support for R7S9210
watchdog: rza_wdt: Support longer timeouts
watchdog: hpwdt: Disable PreTimeout when Timeout is smaller
watchdog: w83627hf_wdt: Support NCT6796D, NCT6797D, NCT6798D
watchdog: mpc8xxx: use dev_xxxx() instead of pr_xxxx()
watchdog: lantiq: add get_timeleft callback
watchdog: lantiq: Convert to watchdog_device
watchdog: lantiq: update register names to better match spec
watchdog: sama5d4: fix timeout-sec usage
watchdog: fix a small number of "watchog" typos in comments
watchdog: rza_wdt: convert to SPDX identifiers
watchdog: iTCO_wdt: Remove unused hooks
...
Pull Devicetree updates from Rob Herring:
"A bit bigger than normal as I've been busy this cycle.
There's a few things with dependencies and a few things subsystem
maintainers didn't pick up, so I'm taking them thru my tree.
The fixes from Johan didn't get into linux-next, but they've been
waiting for some time now and they are what's left of what subsystem
maintainers didn't pick up.
Summary:
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral
bindings out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers"
* tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits)
ARM: dt: relicense two DT binding IRQ headers
power: supply: twl4030-charger: fix OF sibling-node lookup
NFC: nfcmrvl_uart: fix OF child-node lookup
net: stmmac: dwmac-sun8i: fix OF child-node lookup
net: bcmgenet: fix OF child-node lookup
drm/msm: fix OF child-node lookup
drm/mediatek: fix OF sibling-node lookup
of: Add missing exports of node name compare functions
dt-bindings: Add OLPC vendor prefix
dt-bindings: misc: bk4: Add device tree binding for Liebherr's BK4 SPI bus
dt-bindings: thermal: samsung: Add SPDX license identifier
dt-bindings: clock: samsung: Add SPDX license identifiers
dt-bindings: timer: ostm: Add R7S9210 support
dt-bindings: phy: rcar-gen2: Add r8a7744 support
dt-bindings: can: rcar_can: Add r8a7744 support
dt-bindings: timer: renesas, cmt: Document r8a7744 CMT support
dt-bindings: watchdog: renesas-wdt: Document r8a7744 support
dt-bindings: thermal: rcar: Add device tree support for r8a7744
Documentation: dt: Add binding for /secure-chosen/stdout-path
dt-bindings: arm: zte: Move sysctrl bindings to their own doc
...
Pull thermal SoC updates from Eduardo Valentin:
"Several new things coming up. Specifics:
- Rework of tsens and hisi thermal drivers
- OF-thermal now allows sharing multiple cooling devices on maps
- Added support for r8a7744 and R8A77970 on rcar thermal driver
- Added support for r8a774a1 on rcar_gen3 thermal driver
- New thermal driver stm32
- Fixes on multiple thermal drivers: of-thermal, imx, qoriq, armada,
qcom-spmi, rcar, da9062/61"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: (41 commits)
thermal: da9062/61: Prevent hardware access during system suspend
thermal: rcar_thermal: Prevent doing work after unbind
thermal: rcar_thermal: Prevent hardware access during system suspend
thermal: rcar_gen3_thermal: add R8A77980 support
dt-bindings: thermal: rcar-gen3-thermal: document R8A77980 bindings
thermal: add stm32 thermal driver
dt-bindings: stm32-thermal: add binding documentation
thermal: rcar_thermal: add R8A77970 support
dt-bindings: thermal: rcar-thermal: document R8A77970 bindings
thermal: rcar_thermal: fix duplicate IRQ request
dt-bindings: thermal: rcar: Add device tree support for r8a7744
thermal/drivers/hisi: Add the dual clusters sensors for hi3660
thermal/drivers/hisi: Add more sensors channel
thermal/drivers/hisi: Remove pointless irq field
thermal/drivers/hisi: Use platform_get_irq_byname
thermal/drivers/hisi: Replace macro name with relevant sensor location
thermal/drivers/hisi: Add multiple sensors support
thermal/drivers/hisi: Prepare to support multiple sensors
thermal/drivers/hisi: Factor out the probe functions
thermal/drivers/hisi: Set the thermal zone private data to the sensor pointer
...
Pull IOMMU updates from Joerg Roedel:
- Debugfs support for the Intel VT-d driver.
When enabled, it now also exposes some of its internal data
structures to user-space for debugging purposes.
- ARM-SMMU driver now uses the generic deferred flushing and fast-path
iova allocation code.
This is expected to be a major performance improvement, as this
allocation path scales a lot better.
- Support for r8a7744 in the Renesas iommu driver
- Couple of minor fixes and improvements all over the place
* tag 'iommu-updates-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (39 commits)
iommu/arm-smmu-v3: Remove unnecessary wrapper function
iommu/arm-smmu-v3: Add SPDX header
iommu/amd: Add default branch in amd_iommu_capable()
dt-bindings: iommu: ipmmu-vmsa: Add r8a7744 support
iommu/amd: Move iommu_init_pci() to .init section
iommu/arm-smmu: Support non-strict mode
iommu/io-pgtable-arm-v7s: Add support for non-strict mode
iommu/arm-smmu-v3: Add support for non-strict mode
iommu/io-pgtable-arm: Add support for non-strict mode
iommu: Add "iommu.strict" command line option
iommu/dma: Add support for non-strict mode
iommu/arm-smmu: Ensure that page-table updates are visible before TLBI
iommu/arm-smmu-v3: Implement flush_iotlb_all hook
iommu/arm-smmu-v3: Avoid back-to-back CMD_SYNC operations
iommu/arm-smmu-v3: Fix unexpected CMD_SYNC timeout
iommu/io-pgtable-arm: Fix race handling in split_blk_unmap()
iommu/arm-smmu-v3: Fix a couple of minor comment typos
iommu: Fix a typo
iommu: Remove .domain_{get,set}_windows
iommu: Tidy up window attributes
...
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc patches for 4.20-rc1.
Loads of things here, we have new code in all of these driver
subsystems:
- fpga
- stm
- extcon
- nvmem
- eeprom
- hyper-v
- gsmi
- coresight
- thunderbolt
- vmw_balloon
- goldfish
- soundwire
along with lots of fixes and minor changes to other small drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (245 commits)
Documentation/security-bugs: Clarify treatment of embargoed information
lib: Fix ia64 bootloader linkage
MAINTAINERS: Clarify UIO vs UIOVEC maintainer
docs/uio: fix a grammar nitpick
docs: fpga: document programming fpgas using regions
fpga: add devm_fpga_region_create
fpga: bridge: add devm_fpga_bridge_create
fpga: mgr: add devm_fpga_mgr_create
hv_balloon: Replace spin_is_locked() with lockdep
sgi-xp: Replace spin_is_locked() with lockdep
eeprom: New ee1004 driver for DDR4 memory
eeprom: at25: remove unneeded 'at25_remove'
w1: IAD Register is yet readable trough iad sys file. Fix snprintf (%u for unsigned, count for max size).
misc: mic: scif: remove set but not used variables 'src_dma_addr, dst_dma_addr'
misc: mic: fix a DMA pool free failure
platform: goldfish: pipe: Add a blank line to separate varibles and code
platform: goldfish: pipe: Remove redundant casting
platform: goldfish: pipe: Call misc_deregister if init fails
platform: goldfish: pipe: Move the file-scope goldfish_pipe_dev variable into the driver state
platform: goldfish: pipe: Move the file-scope goldfish_pipe_miscdev variable into the driver state
...
