Masking the link partner's capabilities with local capabilities can be
misleading in autonegotiation scenarios such as PAUSE frame
autonegotiation.
This patch calculates the join between the local capabilities and the
link parner capabilities, when it determines the speed and duplex
settings, but does not mask any of the link partner capabilities when
it calculates PAUSE frame settings.
Signed-off-by: Cristian Bercaru <cristian.bercaru@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton akpm@linux-foundation.org>:
MAINTAINERS: change mailing list address for Altera UART drivers
Makefile: fix build with make 3.80 again
MAINTAINERS: update L: misuses
Makefile: fix extra parenthesis typo when CC_STACKPROTECTOR_REGULAR is enabled
ipc,mqueue: remove limits for the amount of system-wide queues
memcg: change oom_info_lock to mutex
mm, thp: fix infinite loop on memcg OOM
drivers/fmc/fmc-write-eeprom.c: fix decimal permissions
drivers/iommu/omap-iommu-debug.c: fix decimal permissions
mm, hwpoison: release page on PageHWPoison() in __do_fault()
netlink_sendmsg() was changed to prevent non-root processes from sending
messages with dst_pid != 0.
netlink_connect() however still only checks if nladdr->nl_groups is set.
This patch modifies netlink_connect() to check for the same condition.
Signed-off-by: Mike Pecovnik <mike.pecovnik@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without a shutdown handler, T4 cards behave very badly after a kexec.
Some firmware calls return errors indicating allocation failures, for
example. This is probably because thouse resources were not released by
a BYE message to the firmware, for example.
Using the remove handler guarantees we will use a well tested path.
With this patch I applied, I managed to use kexec multiple times and
probe and iSCSI login worked every time.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shahed Shaikh says:
====================
qlcnic: Bug fixes
This patch series includes following bug fixes,
* Fix for return value handling of function qlcnic_enable_msi_legacy().
* Fix for the usage of module parameters for interrupt mode.
Driver should use flags while checking for driver's interrupt mode instead of
module parameters.
* Revert commit 1414abea04 (qlcnic: Restrict VF from configuring any VLAN mode),
in order to save some multicast filters.
* Fix a bug where driver was not re-setting sds ring count to 1 when
it falls back from MSI-x mode to legacy interrupt mode.
Please apply to net.
Change in v2 -
Dropped patch "qlcnic: reset firmware API lock during driver load" for further rework.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver was not re-setting sds ring count to 1 after failing
to allocate msi-x interrupts.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o This patch reverts commit 1414abea04
(qlcnic: Restrict VF from configuring any VLAN mode.)
This will allow same multicast address to be used with any VLAN
instead of programming seperate (MAC, VLAN) tuples in adapter.
This will help save some multicast filters.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once interrupts are enabled, instead of using module parameters,
use flags (QLCNIC_MSI_ENABLED and QLCNIC_MSIX_ENABLED) set by driver
to check interrupt mode.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver was treating -ve return value as success in case of
qlcnic_enable_msi_legacy() failure
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To guarantee that a qdio ccw_device no longer touches the
qdio memory shared with Linux, the qdio ccw_device should
be offline when freeing the qdio memory. Thus this patch
postpones freeing of qdio memory.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the UFO fragmentation process does not correctly handle inner
UDP frames.
(The following tcpdumps are captured on the parent interface with ufo
disabled while tunnel has ufo enabled, 2000 bytes payload, mtu 1280,
both sit device):
IPv6:
16:39:10.031613 IP (tos 0x0, ttl 64, id 3208, offset 0, flags [DF], proto IPv6 (41), length 1300)
192.168.122.151 > 1.1.1.1: IP6 (hlim 64, next-header Fragment (44) payload length: 1240) 2001::1 > 2001::8: frag (0x00000001:0|1232) 44883 > distinct: UDP, length 2000
16:39:10.031709 IP (tos 0x0, ttl 64, id 3209, offset 0, flags [DF], proto IPv6 (41), length 844)
192.168.122.151 > 1.1.1.1: IP6 (hlim 64, next-header Fragment (44) payload length: 784) 2001::1 > 2001::8: frag (0x00000001:0|776) 58979 > 46366: UDP, length 5471
We can see that fragmentation header offset is not correctly updated.
(fragmentation id handling is corrected by 916e4cf46d ("ipv6: reuse
ip6_frag_id from ip6_ufo_append_data")).
IPv4:
16:39:57.737761 IP (tos 0x0, ttl 64, id 3209, offset 0, flags [DF], proto IPIP (4), length 1296)
192.168.122.151 > 1.1.1.1: IP (tos 0x0, ttl 64, id 57034, offset 0, flags [none], proto UDP (17), length 1276)
192.168.99.1.35961 > 192.168.99.2.distinct: UDP, length 2000
16:39:57.738028 IP (tos 0x0, ttl 64, id 3210, offset 0, flags [DF], proto IPIP (4), length 792)
192.168.122.151 > 1.1.1.1: IP (tos 0x0, ttl 64, id 57035, offset 0, flags [none], proto UDP (17), length 772)
192.168.99.1.13531 > 192.168.99.2.20653: UDP, length 51109
In this case fragmentation id is incremented and offset is not updated.
First, I aligned inet_gso_segment and ipv6_gso_segment:
* align naming of flags
* ipv6_gso_segment: setting skb->encapsulation is unnecessary, as we
always ensure that the state of this flag is left untouched when
returning from upper gso segmenation function
* ipv6_gso_segment: move skb_reset_inner_headers below updating the
fragmentation header data, we don't care for updating fragmentation
header data
* remove currently unneeded comment indicating skb->encapsulation might
get changed by upper gso_segment callback (gre and udp-tunnel reset
encapsulation after segmentation on each fragment)
If we encounter an IPIP or SIT gso skb we now check for the protocol ==
IPPROTO_UDP and that we at least have already traversed another ip(6)
protocol header.
The reason why we have to special case GSO_IPIP and GSO_SIT is that
we reset skb->encapsulation to 0 while skb_mac_gso_segment the inner
protocol of GSO_UDP_TUNNEL or GSO_GRE packets.
Reported-by: Wolfgang Walter <linux@stwm.de>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Documentation/Changes, make 3.80 is still being supported
for building the kernel, hence make files must not make (unconditional)
use of features introduced only in newer versions. Commit 8779657d29
("stackprotector: Introduce CONFIG_CC_STACKPROTECTOR_STRONG") however
introduced an "else ifdef" construct which make 3.80 doesn't understand.
Also correct a warning message still referencing the old config option
name.
Apart from that I question the use of "ifdef" here (but it was used that
way already prior to said commit): ifeq (,y) would seem more to the
point.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An extra parenthesis typo introduced in 19952a9203 ("stackprotector:
Unify the HAVE_CC_STACKPROTECTOR logic between architectures") is
causing the following error when CONFIG_CC_STACKPROTECTOR_REGULAR is
enabled:
Makefile:608: Cannot use CONFIG_CC_STACKPROTECTOR: -fstack-protector not supported by compiler
Makefile:608: *** missing separator. Stop.
Signed-off-by: Fathi Boudra <fathi.boudra@linaro.org>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 93e6f119c0 ("ipc/mqueue: cleanup definition names and
locations") added global hardcoded limits to the amount of message
queues that can be created. While these limits are per-namespace,
reality is that it ends up breaking userspace applications.
Historically users have, at least in theory, been able to create up to
INT_MAX queues, and limiting it to just 1024 is way too low and dramatic
for some workloads and use cases. For instance, Madars reports:
"This update imposes bad limits on our multi-process application. As
our app uses approaches that each process opens its own set of queues
(usually something about 3-5 queues per process). In some scenarios
we might run up to 3000 processes or more (which of-course for linux
is not a problem). Thus we might need up to 9000 queues or more. All
processes run under one user."
Other affected users can be found in launchpad bug #1155695:
https://bugs.launchpad.net/ubuntu/+source/manpages/+bug/1155695
Instead of increasing this limit, revert it entirely and fallback to the
original way of dealing queue limits -- where once a user's resource
limit is reached, and all memory is used, new queues cannot be created.
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Reported-by: Madars Vitolins <m@silodev.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: <stable@vger.kernel.org> [3.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kirill has reported the following:
Task in /test killed as a result of limit of /test
memory: usage 10240kB, limit 10240kB, failcnt 51
memory+swap: usage 10240kB, limit 10240kB, failcnt 0
kmem: usage 0kB, limit 18014398509481983kB, failcnt 0
Memory cgroup stats for /test:
BUG: sleeping function called from invalid context at kernel/cpu.c:68
in_atomic(): 1, irqs_disabled(): 0, pid: 66, name: memcg_test
2 locks held by memcg_test/66:
#0: (memcg_oom_lock#2){+.+...}, at: [<ffffffff81131014>] pagefault_out_of_memory+0x14/0x90
#1: (oom_info_lock){+.+...}, at: [<ffffffff81197b2a>] mem_cgroup_print_oom_info+0x2a/0x390
CPU: 2 PID: 66 Comm: memcg_test Not tainted 3.14.0-rc1-dirty #745
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS Bochs 01/01/2011
Call Trace:
__might_sleep+0x16a/0x210
get_online_cpus+0x1c/0x60
mem_cgroup_read_stat+0x27/0xb0
mem_cgroup_print_oom_info+0x260/0x390
dump_header+0x88/0x251
? trace_hardirqs_on+0xd/0x10
oom_kill_process+0x258/0x3d0
mem_cgroup_oom_synchronize+0x656/0x6c0
? mem_cgroup_charge_common+0xd0/0xd0
pagefault_out_of_memory+0x14/0x90
mm_fault_error+0x91/0x189
__do_page_fault+0x48e/0x580
do_page_fault+0xe/0x10
page_fault+0x22/0x30
which complains that mem_cgroup_read_stat cannot be called from an atomic
context but mem_cgroup_print_oom_info takes a spinlock. Change
oom_info_lock to a mutex.
This was introduced by 947b3dd1a8 ("memcg, oom: lock
mem_cgroup_print_oom_info").
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Reported-by: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Masayoshi Mizuma reported a bug with the hang of an application under
the memcg limit. It happens on write-protection fault to huge zero page
If we successfully allocate a huge page to replace zero page but hit the
memcg limit we need to split the zero page with split_huge_page_pmd()
and fallback to small pages.
The other part of the problem is that VM_FAULT_OOM has special meaning
in do_huge_pmd_wp_page() context. __handle_mm_fault() expects the page
to be split if it sees VM_FAULT_OOM and it will will retry page fault
handling. This causes an infinite loop if the page was not split.
do_huge_pmd_wp_zero_page_fallback() can return VM_FAULT_OOM if it failed
to allocate one small page, so fallback to small pages will not help.
The solution for this part is to replace VM_FAULT_OOM with
VM_FAULT_FALLBACK is fallback required.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix irq_set_affinity callbacks in the Meta IRQ chip drivers to AND
cpu_online_mask into the cpumask when picking a CPU to vector the
interrupt to.
As Thomas pointed out, the /proc/irq/$N/smp_affinity interface doesn't
filter out offline CPUs, so without this patch if you offline CPU0 and
set an IRQ affinity to 0x3 it vectors the interrupt onto CPU0 even
though it is offline.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-metag@vger.kernel.org
Cc: stable@vger.kernel.org
Pull dmaengine fixes from Dan Williams:
"Fix tasklet lifetime management in the ioat driver causing ksoftirqd
to spin indefinitely.
References:
https://lkml.org/lkml/2014/1/27/282https://lkml.org/lkml/2014/2/19/672"
* tag 'dmaengine-fixes-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
ioat: fix tasklet tear down
Pull MTD fixes from Brian Norris:
"Two main MTD fixes:
1. Read retry counting was off by one, so if we had a true ECC error
(i.e., no retry voltage threshold would give a clean read), we
would end up returning -EINVAL on the Nth mode instead of -EBADMSG
after then (N-1)th mode
2. The OMAP NAND driver had some of its ECC layouts wrong when
introduced in 3.13, causing incompatibilities between the
bootloader on-flash layout and the layout expected in Linux. The
expected layouts are now documented in the commit messages, and we
plan to add this under Documentation/mtd/nand/ eventually"
* tag 'for-linus-20140225' of git://git.infradead.org/linux-mtd:
mtd: nand: omap: fix ecclayout->oobfree->length
mtd: nand: omap: fix ecclayout->oobfree->offset
mtd: nand: omap: fix ecclayout to be in sync with u-boot NAND driver
mtd: nand: fix off-by-one read retry mode counting
Pull m68k update from Geert Uytterhoeven:
- More barrier.h consolidation
- Sched_[gs]etattr() syscalls
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up sched_setattr and sched_getattr
m68k: Switch to asm-generic/barrier.h
m68k: Sort arch/m68k/include/asm/Kbuild
Pull tensa fixes from Chris Zankel:
"This series includes fixes for potentially serious bugs in the
routines spilling processor registers to stack, as well as other
issues and compiler errors and warnings.
- allow booting xtfpga on boards with new uBoot and >128MBytes memory
- drop nonexistent GPIO32 support from fsf variant
- don't select USE_GENERIC_SMP_HELPERS
- enable common clock framework support, set up ethoc clock on xtfpga
- wire up sched_setattr and sched_getattr syscalls.
- fix system call to spill the processor registers to stack.
- improve kernel macro to spill the processor registers
- export ccount_freq symbol
- fix undefined symbol warning"
* tag 'xtensa-next-20140224' of git://github.com/czankel/xtensa-linux:
xtensa: wire up sched_setattr and sched_getattr syscalls
xtensa: xtfpga: set ethoc clock frequency
xtensa: xtfpga: use common clock framework
xtensa: support common clock framework
xtensa: no need to select USE_GENERIC_SMP_HELPERS
xtensa: fsf: drop nonexistent GPIO32 support
xtensa: don't pass high memory to bootmem allocator
xtensa: fix fast_syscall_spill_registers
xtensa: fix fast_syscall_spill_registers
xtensa: save current register frame in fast_syscall_spill_registers_fixup
xtensa: introduce spill_registers_kernel macro
xtensa: export ccount_freq
xtensa: fix warning '"CONFIG_OF" is not defined'
The Core Specification (4.1) leaves room for sending an SMP Identity
Address Information PDU with an all-zeros BD_ADDR value. This
essentially means that we would not have an Identity Address for the
device and the only means of identifying it would be the IRK value
itself.
Due to lack of any known implementations behaving like this it's best to
keep our implementation as simple as possible as far as handling such
situations is concerned. This patch updates the Identity Address
Information handler function to simply ignore the IRK received from such
a device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only set sc->rx.discard_next to rx_stats->rs_more when actually
discarding the current descriptor.
Also, fix a detection of broken descriptors:
First the code checks if the current descriptor is not done.
Then it checks if the next descriptor is done.
Add a check that afterwards checks the first descriptor again, because
it might have been completed in the mean time.
This fixes a regression introduced in
commit 723e711356
"ath9k: fix handling of broken descriptors"
Cc: stable@vger.kernel.org
Reported-by: Marco André Dinis <marcoandredinis@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check if the baseband state remains stable, and add a small delay
between register reads.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the connectable setting is toggled using mgmt_set_connectable the
HCI_CONNECTABLE flag will only be set once the related HCI commands
succeed. When determining what kind of advertising to do we need to
therefore also check whether there is a pending Set Connectable command
in addition to the current flag value.
The enable_advertising function was already taking care of this for the
advertising type with the help of the get_adv_type function, but was
failing to do the same for the address type selection. This patch
converts the get_adv_type function to be more generic in that it returns
the expected connectable state and updates the enable_advertising
function to use the return value both for the advertising type as well
as the advertising address type.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since commit 7787380336 "net_dma: mark broken" we no longer pin dma
engines active for the network-receive-offload use case. As a result
the ->free_chan_resources() that occurs after the driver self test no
longer has a NET_DMA induced ->alloc_chan_resources() to back it up. A
late firing irq can lead to ksoftirqd spinning indefinitely due to the
tasklet_disable() performed by ->free_chan_resources(). Only
->alloc_chan_resources() can clear this condition in affected kernels.
This problem has been present since commit 3e037454bc "I/OAT: Add
support for MSI and MSI-X" in 2.6.24, but is now exposed. Given the
NET_DMA use case is deprecated we can revisit moving the driver to use
threaded irqs. For now, just tear down the irq and tasklet properly by:
1/ Disable the irq from triggering the tasklet
2/ Disable the irq from re-arming
3/ Flush inflight interrupts
4/ Flush the timer
5/ Flush inflight tasklets
References:
https://lkml.org/lkml/2014/1/27/282https://lkml.org/lkml/2014/2/19/672
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: <stable@vger.kernel.org>
Reported-by: Mike Galbraith <bitbucket@online.de>
Reported-by: Stanislav Fomichev <stfomichev@yandex-team.ru>
Tested-by: Mike Galbraith <bitbucket@online.de>
Tested-by: Stanislav Fomichev <stfomichev@yandex-team.ru>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As mount() and kill_sb() is not a one-to-one match, we shoudn't get
ns refcnt unconditionally in sysfs_mount(), and instead we should
get the refcnt only when kernfs_mount() allocated a new superblock.
v2:
- Changed the name of the new argument, suggested by Tejun.
- Made the argument optional, suggested by Tejun.
v3:
- Make the new argument as second-to-last arg, suggested by Tejun.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
---
fs/kernfs/mount.c | 8 +++++++-
fs/sysfs/mount.c | 5 +++--
include/linux/kernfs.h | 9 +++++----
3 files changed, 15 insertions(+), 7 deletions(-)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reset regdomain to world regdomain in case
of errors in set_regdom() function.
This will fix a problem with such scenario:
- iw reg set US
- iw reg set 00
- iw reg set US
The last step always fail and we get deadlock
in kernel regulatory code. Next setting new
regulatory wasn't possible due to:
Pending regulatory request, waiting for it to be processed...
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 7053aee26a "fsnotify: do not share events between notification
groups" used overflow event statically allocated in a group with the
size of the generic notification event. This causes problems because
some code looks at type specific parts of event structure and gets
confused by a random data it sees there and causes crashes.
Fix the problem by allocating overflow event with type corresponding to
the group type so code cannot get confused.
Signed-off-by: Jan Kara <jack@suse.cz>
If the event queue overflows when we are handling permission event, we
will never get response from userspace. So we must avoid waiting for it.
Change fsnotify_add_notify_event() to return whether overflow has
happened so that we can detect it in fanotify_handle_event() and act
accordingly.
Signed-off-by: Jan Kara <jack@suse.cz>
Currently we didn't initialize event's list head when we removed it from
the event list. Thus a detection whether overflow event is already
queued wasn't working. Fix it by always initializing the list head when
deleting event from a list.
Signed-off-by: Jan Kara <jack@suse.cz>
pci_get_device() decrements the reference count of "from" (last
argument) so when we break off the loop successfully we have only one
device reference - and we don't know which device we have. If we want
a reference to each device, we must take them explicitly and let
the pci_get_device() walk complete to avoid duplicate references.
This is serious, as over-putting device references will cause
the device to eventually disappear. Without this fix, the kernel
crashes after a few insmod/rmmod cycles.
Tested on an Intel S7000FC4UR system with a 7300 chipset.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: http://lkml.kernel.org/r/20140224111656.09bbb7ed@endymion.delvare
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: stable@vger.kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
The reference count changes done by pci_get_device can be a little
misleading when the usage diverges from the most common scheme. The
reference count of the device passed as the last parameter is always
decreased, even if the function returns no new device. So if we are
going to try alternative device IDs, we must manually increment the
device reference count before each retry. If we don't, we end up
decreasing the reference count, and after a few modprobe/rmmod cycles
the PCI devices will vanish.
In other words and as Alan put it: without this fix the EDAC code
corrupts the PCI device list.
This fixes kernel bug #50491:
https://bugzilla.kernel.org/show_bug.cgi?id=50491
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: http://lkml.kernel.org/r/20140224093927.7659dd9d@endymion.delvare
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: stable@vger.kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
The tunnel endpoints of the xfrm_state we got from the xfrm_lookup
must match the tunnel endpoints of the vti interface. This patch
ensures this matching.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
With this patch we can tunnel ipv6 traffic via a vti4
interface. A vti4 interface can now have an ipv6 address
and ipv6 traffic can be routed via a vti4 interface.
The resulting traffic is xfrm transformed and tunneled
throuhg ipv4 if matching IPsec policies and states are
present.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We need to be protocol family indepenent to support
inter addresss family tunneling with vti. So use a
dst_entry instead of the ipv4 rtable in vti_tunnel_xmit.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This was used from vti and is replaced by the IPsec protocol
multiplexer hooks. It is now unused, so remove it.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
With this patch, vti uses the IPsec protocol multiplexer to
register it's own receive side hooks for ESP, AH and IPCOMP.
Vti now does the following on receive side:
1. Do an input policy check for the IPsec packet we received.
This is required because this packet could be already
prosecces by IPsec, so an inbuond policy check is needed.
2. Mark the packet with the i_key. The policy and the state
must match this key now. Policy and state belong to the outer
namespace and policy enforcement is done at the further layers.
3. Call the generic xfrm layer to do decryption and decapsulation.
4. Wait for a callback from the xfrm layer to properly clean the
skb to not leak informations on namespace and to update the
device statistics.
On transmit side:
1. Mark the packet with the o_key. The policy and the state
must match this key now.
2. Do a xfrm_lookup on the original packet with the mark applied.
3. Check if we got an IPsec route.
4. Clean the skb to not leak informations on namespace
transitions.
5. Attach the dst_enty we got from the xfrm_lookup to the skb.
6. Call dst_output to do the IPsec processing.
7. Do the device statistics.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Vti uses the o_key to mark packets that were transmitted or received
by a vti interface. Unfortunately we can't apply different marks
to in and outbound packets with only one key availabe. Vti interfaces
typically use wildcard selectors for vti IPsec policies. On forwarding,
the same output policy will match for both directions. This generates
a loop between the IPsec gateways until the ttl of the packet is
exceeded.
The gre i_key/o_key are usually there to find the right gre tunnel
during a lookup. When vti uses the i_key to mark packets, the tunnel
lookup does not work any more because vti does not use the gre keys
as a hash key for the lookup.
This patch workarounds this my not including the i_key when comupting
the hash for the tunnel lookup in case of vti tunnels.
With this we have separate keys available for the transmitting and
receiving side of the vti interface.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
