1) Fix a name of the error bit to correctly indicate the error.
2) Added a fd_id field in the 32 byte desc at the place(qw0) where it gets
reported in the programming error desc WB. In a normal data desc
the fd_id field is reported in qw3.
Change-ID: Ide9a24bff7273da5889c36635d629bc3b5212010
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The update filter logic was causing a kernel panic in the original code.
We need to compare the input set to decide whether or not to delete a
filter since we do not have a hash stored. This new design helps fix the issue.
Change-ID: I2462b108e58ca4833312804cda730b4660cc18c9
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We've been deleting the netdev before getting around to deleting the napi
structs. Unfortunately, we then didn't delete the napi structs because we
have a check for netdev, thus we were leaving garbage around in the system.
Change-ID: Ife540176f6c9f801147495b3f2d2ac2e61ddcc58
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to make sure that we stay away from the cache line
where the DD bit (done) may be getting written back for
the transmit ring since the hardware may be writing the
whole cache line for a partial update.
Change-ID: Id0b6dfc01f654def6a2a021af185803be1915d7e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver needs to use the format that the current NVM
uses when printing the version of the NVM. It should remain
this way from now on forward.
The driver was reporting when firmware was less than
an expected version number, but this is not a requirement
for the product and we print the firmware number at
init and in ethtool -i output. Just remove the print.
Change-ID: Ide0b856cd454ebf867610ef9a0d639bb358a4a60
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the do/while to a for loop, so we don't hit the delay each
time, even when the register is ready for action.
Don't bother to set or clear the QENA_STAT bit as it is
read-only.
Change-ID: Ie464718804dd79f6d726f291caa9b0c872b49978
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ain't nothing gonna break my stride, nobody's gonna slow me down,
oh no. I got to keep on moving.
This was originally put in for debugging just-in-case purposes
and never removed.
Change-ID: Ic12c2e179c3923f54e6ba0a9e4ab05d25c3bab29
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the DOWN flag before attempting to disable VFs when unloading the
driver. Also, don't attempt to reset the VFs when the driver is
unloading, because the switch configuration will fail. This fixes a
panic on unload when VFs are enabled.
Change-ID: I25a6567e89c9687145f510ff4f630932412c5c5d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset all of the VFs after a PF reset, so that they are in a known
state, and the VF driver can detect the reset and reinit itself.
Change-ID: I93c5b3a0f8b1371d0da078f92de948b9d3a6413f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This looks like a cut and paste error. The code makes no sense where
it is, and accomplishes nothing. Since we've removed the goto, we can
also get rid of the extraneous brackets.
Change-ID: I9315e3eafeee0a5713c94b0dc57b58b60a849124
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indentation mismatch spotted with Coverity.
Introduced in 4e3b35b044 ("i40e: add DCB and DCBNL support")
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds capability to configure DCB on i40e network
interfaces using Intel XL710 adapter firmware APIs.
By default all VSIs are only enabled for the default traffic
class enabled by firmware for any given PF. The driver would
query the firmware for the traffic classes that are enabled for
the port and reconfigure the LAN VSI to match to the port traffic
class settings. All other VSIs are only enabled for the default
traffic class settings for now.
The driver registers and listens to firmware events that may
require change in the DCB settings. It may reconfigure the VSI
settings based on these events.
This patch exposes IEEE DCBNL interfaces for the i40e driver to
allow any application to query the DCB settings on the adapter.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-By: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel XL710 series of adapters support QoS as per the
IEEE 802.1 DCB (Data Center Bridging) standard.
This is supported in conjuction with:
- Enhanced Transmission Selection (ETS) - IEEE 802.1Qaz
- Priority Flow Control (PFC) - IEEE 802.1Qbb
- DCB eXchange Protocol (DCBX) - IEEE 802.1Qaz
On Intel XL710 adapters DCBX is performed by the adapter
firmware. The firmware runs DCBX in willing mode and configures
the port as per the DCB settings recommended by it's link
partner.
By default in absence of any DCBX; firmware would configure the
port with a single traffic class and all of the port bandwith
will be allocated to that traffic class.
This patch adds functions and calls to support querying and
configuring DCB using firmware APIs.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-By: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i40e hardware was generating some inconsistent results
when using current programming methods. This refactor
fixes the inconsistencies that were preventing clean
unloads of the driver, and moves the queues for handling
flow director errors into their own hardware VSI.
This patch also implements a corrected version of the
basic ethtool add ntuple rule, which will disable
the driver's automatic flow programming. A future patch
adds remove/replay/list support for ntuple.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a workaround that is no longer necessary and implement
a better understanding of what firmware is returning in the MSI-X
vector count. This makes it so that the driver ends up with the
right amount of queues when using all available MSI-X vectors.
Change-ID: I34e60cc71dcfb1b5412f37df956fedcc49ade187
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that the descriptors were allocated before trying to dump
them to the logfile. While we're there, de-trick-ify the code
so as to be easier to read and not abusing the types and unions.
Change-ID: I22898f4b22cecda3582d4d9e4018da9cd540f177
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On port VLAN deletion the list of MAC filters for the virtual function (VF)
VSI were all deleted. Let's keep them around, they come in handy for keeping
the VF functional.
Change-Id: I335e760392f274dc8b8b40efcb708f65b49d7973
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i40e Physical Function (PF) driver will allow the
Virtual Function (VF) driver to configure its own VLAN filters if no port
VLAN filter has been configured. This leads to the possibility of the
administrator setting a port VLAN filter for the VF after the VF has already
configured its own VLAN filters. This leads to a conflict that can only be
resolved by reloading the VF driver. When the conflicting administrative
command is detected in setting the port VLAN then log a message indicating to
the system administrator that he must now reload the VF driver for the new
port VLAN settings to take effect.
Change-Id: I8de73b885d944a043aff32226297e4249862bcad
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug where the queue was not associated with the right set-up
within the hardware. The fix is to use the right QTX_CTL VSI type
when associating it to the VSI.
Change-ID: I65ef6c5a8205601c640a6593e4b7e78d6ba45545
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
