During initialization, when creating the send descriptor queues (SDQs),
we specify the CPU egress traffic class of each SDQ. The maximum number
of classes of this type is different in the two ASICs supported by this
PCI driver.
New firmware versions check this value is set correctly, which causes
errors on the Spectrum ASIC, as its max exposed egress traffic class is
lower than 7.
Solve this by setting this field to 3, which is an acceptable value for
both ASICs.
Note that we currently do not expose the QoS capabilities of the ASICs,
so setting this to an hardcoded value is OK for now.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc fails to see that the use of the 'last_offset' variable
in hns_nic_reuse_page() is used correctly and issues a bogus
warning:
drivers/net/ethernet/hisilicon/hns/hns_enet.c: In function 'hns_nic_reuse_page':
drivers/net/ethernet/hisilicon/hns/hns_enet.c:541:6: warning: 'last_offset' may be used uninitialized in this function [-Wmaybe-uninitialized]
This simplifies the function to make it more obvious what is
going on to both readers and compilers, which makes the warning
go away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a PHC support to the mlx5_en driver. Use reader/writer spinlocks to
protect the timecounter since every packet received needs to call
timecounter_cycle2time() when timestamping is enabled. This can become
a performance bottleneck with RSS and multiple receive queues if normal
spinlocks are used.
The driver has been tested with both Documentation/ptp/testptp and the
linuxptp project (http://linuxptp.sourceforge.net/) on a Mellanox
ConnectX-4 card.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for enable/disable HW timestamping for incoming and/or
outgoing packets. To enable/disable HW timestamping appropriate
ioctl should be used. Currently HWTSTAMP_FILTER_ALL/NONE and
HWTSAMP_TX_ON/OFF only are supported. Make all relevant changes in
RX/TX flows to consider TS request and plant HW timestamps into
relevant structures.
Add internal clock for converting hardware timestamp to nanoseconds. In
addition, add a service task to catch internal clock overflow, to make
sure timestamping is accurate.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A preparation step which adds support for reading the hardware
internal timer and the hardware timestamping from the CQE.
In addition, advertize device_frequency_khz HCA capability.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the SKB is cloned, or has an elevated users count, someone else
can be looking at it at the same time.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge port attributes are offloaded to hardware when invoked with SELF
flag set, but it really makes no sense to reflect them when port is not
bridged.
Allow a user to change these attribute only when port is bridged and
initialize them correctly when joining or leaving a bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the bridge status of physical ports in the appropriate functions, to
be consistent with LAG join/leave and vPorts joining/leaving bridge.
Also, remove the error messages in these two functions, as we already
emit errors in both the single functions they call.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for us to fail when joining or leaving a bridge, so let
the user know about that by returning NOTIFY_BAD, as already done for
LAG join/leave and 802.1D bridges.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set PVID to 1 in mlxsw_sp_port_vlan_init(), so we can remove this
statement.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cphy_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARM allmodconfig fails because of the addition of the FMAN driver:
drivers/built-in.o: In function `dtsec_restart_autoneg':
binder.c:(.text+0x173328): undefined reference to `mdiobus_read'
binder.c:(.text+0x173348): undefined reference to `mdiobus_write'
drivers/built-in.o: In function `dtsec_config':
binder.c:(.text+0x173d24): undefined reference to `of_phy_find_device'
drivers/built-in.o: In function `init_phy':
binder.c:(.text+0x1763b0): undefined reference to `of_phy_connect'
drivers/built-in.o: In function `stop':
binder.c:(.text+0x176014): undefined reference to `phy_stop'
drivers/built-in.o: In function `start':
binder.c:(.text+0x176078): undefined reference to `phy_start'
The reason is that the driver uses PHYLIB, but that is a loadable
module here, and fman itself is built-in.
This patch makes it possible to configure fman as a module as well
so we don't change the status of PHYLIB in an allmodconfig kernel,
and it adds a 'select PHYLIB' statement to ensure that phylib is
always built-in when fman is.
The driver uses "builtin_platform_driver(fman_driver);", which means
it cannot be unloaded, but it's still possible to have it as a loadable
module that gets loaded once and never removed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5adae51a64 ("fsl/fman: Add FMan MURAM support")
Signed-off-by: David S. Miller <davem@davemloft.net>
The original way is wrong, it always writes ephy reg 0x03.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY PFM register is in PHY page 0x0a44 register 0x11, not 0x14.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that {cpu|edmac}_to_{edmac|cpu}() functions boiled down to the mere
{cpu|le32}_to_{le32|cpu}() calls, there's no need for these functions
anymore, so just get rid of them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 71557a37ad ("[netdrvr] sh_eth: Add SH7619 support") added support
for the big-endian EDMAC descriptors. However, it was never used and never
worked right until the recent driver fixes. I think we now can just remove
this support, it was only burdening the driver from the start. It should be
easy to do without disturbing the SH platform code, at least for now...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can support either all combined or all rx/tx rings. The
default is combined, but the user can now select rx/tx rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify ring memory allocation and MSIX setup to support shared or
non shared rings and do the proper mapping. Default is still to
use shared rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add logic to calculate how many shared or non shared rings can be
supported. Default is to use shared rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support dedicated or shared completion rings, the ring
indexing and mapping are re-structured as below:
1. bp->grp_info[] array index is 1:1 with bp->bnapi[] array index and
completion ring index.
2. rx rings 0 to n will be mapped to completion rings 0 to n.
3. If tx and rx rings share completion rings, then tx rings 0 to m will
be mapped to completion rings 0 to m.
4. If tx and rx rings use dedicated completion rings, then tx rings 0 to
m will be mapped to completion rings n + 1 to n + m.
5. Each tx or rx ring will use the corresponding completion ring index
for doorbell mapping and MSIX mapping.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each bnxt_napi structure may no longer be having both an rx ring and
a tx ring. Check for a valid ring before using it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, an rx and a tx ring are always paired with a completion ring.
We want to restructure it so that it is possible to have a dedicated
completion ring for tx or rx only.
The bnxt hardware uses a completion ring for rx and tx events. The driver
has to process the completion ring entries sequentially for the rx and tx
events. Using a dedicated completion ring for rx only or tx only has these
benefits:
1. A burst of rx packets can cause delay in processing tx events if the
completion ring is shared. If tx queue is stopped by BQL, this can cause
delay in re-starting the tx queue.
2. A completion ring is sized according to the rx and tx ring size rounded
up to the nearest power of 2. When the completion ring is shared, it is
sized by adding the rx and tx ring sizes and then rounded to the next power
of 2, often with a lot of wasted space.
3. Using dedicated completion ring, we can adjust the tx and rx coalescing
parameters independently for rx and tx.
The first step is to separate the rx and tx ring structures from the
bnxt_napi struct.
In this patch, an rx ring and a tx ring will point to the same bnxt_napi
struct to share the same completion ring. No change in ring assignment
and mapping yet.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By adding 3 separate functions to dump the different ring states.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Prevent XFRM per-cpu counter updates for one namespace from being
applied to another namespace. Fix from DanS treetman.
2) Fix RCU de-reference in iwl_mvm_get_key_sta_id(), from Johannes
Berg.
3) Remove ethernet header assumption in nft_do_chain_netdev(), from
Pablo Neira Ayuso.
4) Fix cpsw PHY ident with multiple slaves and fixed-phy, from Pascal
Speck.
5) Fix use after free in sixpack_close and mkiss_close.
6) Fix VXLAN fw assertion on bnx2x, from Yuval Mintz.
7) natsemi doesn't check for DMA mapping errors, from Alexey
Khoroshilov.
8) Fix inverted test in ip6addrlbl_get(), from ANdrey Ryabinin.
9) Missing initialization of needed_headroom in geneve tunnel driver,
from Paolo Abeni.
10) Fix conntrack template leak in openvswitch, from Joe Stringer.
11) Mission initialization of wq->flags in sock_alloc_inode(), from
Nicolai Stange.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
sctp: sctp should release assoc when sctp_make_abort_user return NULL in sctp_close
net, socket, socket_wq: fix missing initialization of flags
drivers: net: cpsw: fix error return code
openvswitch: Fix template leak in error cases.
sctp: label accepted/peeled off sockets
sctp: use GFP_USER for user-controlled kmalloc
qlcnic: fix a loop exit condition better
net: cdc_ncm: avoid changing RX/TX buffers on MTU changes
geneve: initialize needed_headroom
ipv6: honor ifindex in case we receive ll addresses in router advertisements
addrconf: always initialize sysctl table data
ipv6/addrlabel: fix ip6addrlbl_get()
switchdev: bridge: Pass ageing time as clock_t instead of jiffies
sh_eth: fix 16-bit descriptor field access endianness too
veth: don’t modify ip_summed; doing so treats packets with bad checksums as good.
net: usb: cdc_ncm: Adding Dell DW5813 LTE AT&T Mobile Broadband Card
net: usb: cdc_ncm: Adding Dell DW5812 LTE Verizon Mobile Broadband Card
natsemi: add checks for dma mapping errors
rhashtable: Kill harmless RCU warning in rhashtable_walk_init
openvswitch: correct encoding of set tunnel action attributes
...
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2015-12-29
This series contains updates to ixgbe and ixgbevf.
William Dauchy provides a fix for ixgbevf that was implemented for ixgbe,
commit 5d6002b7b8 ("ixgbe: Fix handling of NAPI budget when multiple
queues are enabled per vector"). The issue was that the polling routine
would increase the budget for receive to at least 1 per queue if multiple
queues were present, which resulted in receive packets being processed
when the budget was 0.
Emil provides minor cleanups for ixgbevf, one being that we need to
check rx_itr_setting with == and not &, since it is not a mask. Added
QSFP PHY support in ixgbe to allow for more accurate reporting of port
settings. Fixed the max RSS limit for X550 which is 63, not 64.
Veola fixes ixgbe ethtool reporting of backplane type interfaces as
1000/10000baseT link modes, instead, report the media as KR, KX or KX4
based on the backplane interface present.
Mark cleans up redundancy in the setting of hw_enc_features that makes
it appear that X550 has more encapsulation features than other devices.
Also do not set NETIF_F_SG any longer since that is set by the
register_netdev() call. Also fixed the X550EM_x revision check, which
needs to check a value, not just a bit.
Alex Duyck fixes additional bugs in ixgbe_clear_vf_vlans(), one being
that the mask was using a divide instead of a modulus, which resulted
in the mask bit being incorrectly set to 0 or 1 based on the value of
the VF being tested. Alex also found that he was not consistent in
using the "word" argument as an offset or as a register offset, so
made the code consistently use word as the offset in the array.
v2: dropped patch 8 of the original series, as it was undoing a part of
the fix Alex Duyck was doing in patch 9 of the original series.
Dropped based on feedback from Emil (the author).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ethtool's --get-dump option in be2net,
to retrieve FW dump. In the past when this option was not yet available,
this feature was supported via the --register-dump option as a workaround.
This patch removes support for FW-dump via --register-dump option as it is
now available via --get-dump option. Even though the
"ethtool --register-dump" cmd which used to work earlier, will now fail
with ENOTSUPP error, we feel it is not an issue as this is used only
for diagnostics purpose.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 72ef3a88fa ("be2net: set pci_func_num while issuing
GET_PROFILE_CONFIG cmd") passed a specific pf_num while issuing a
GET_PROFILE_CONFIG cmd as FW returns descriptors for all functions when
pf_num is zero. But, when pf_num is set to a non-zero value, FW does not
return the Port resource descriptor.
This patch fixes this by setting pf_num to 0 while issuing the query cmd
and adds code to pick the correct NIC resource descriptor from the list of
descriptors returned by FW.
Fixes: 72ef3a88fa ("be2net: set pci_func_num while issuing
GET_PROFILE_CONFIG cmd")
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eeh_error, fw_timeout, hw_error variables in the be_adapter structure are
not used anymore. An earlier patch that introduced adapter->err_flags to
store this information missed removing these variables.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a line of code that changes adapter->recommended_prio
value followed by yet another assignment.
Also, the variable is used to store the vlan priority value that is already
shifted to the PCP bits position in the vlan tag format. Hence, the name of
this variable is changed to recommended_prio_bits.
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(based on a jumper setting on the adapter.) In this mode, the FW image when
flashed is authenticated with a digital signature. This patch logs
appropriate error messages and return a status to ethtool when errors
relating to FW image authentication occur.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All code relating to FW cmds is in be_cmds.[ch] excepting FW flash cmd
related code. This patch moves these routines from be_main.c to be_cmds.c
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many constant definitions relating to the FW-image layout
(such as section offset values) were defined in decimal format rather than
hexa-decimal. This makes this part of the code un-readable. Also some
defines related to BE2 are labeld "g2" and defines related to BE3 are
labeled "g3". This patch cleans up all of this to make this code more
readable.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VF link state setting transition from "disable" to "auto" does not work
due to a bug in SET_LOGICAL_LINK_CONFIG_V1 cmd in FW. This issue could not
be fixed in FW due to some backward compatibility issues it causes with
some released drivers. The issue has been fixed by introducing a new
version (v2) of the cmd from 10.6 FW onwards. In v2, to set the VF link
state to auto, both PLINK_ENABLE and PLINK_TRACK bits have to be set to 1.
The VF link state setting feature now works on Lancer chips too from
FW ver 10.6.315.0 onwards.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I had rewritten the code for ixgbe_clear_vf_vlans() it looks like I
had transitioned back and forth between using word as an offset and using
word as a register offset. As a result I honestly don't see how the code
was working before other than the fact that resetting the VLANs on the VF
like didn't do much to clear them.
Another issue found is that the mask was using a divide instead of a
modulus. As a result the mask bit was incorrectly being set to either bit
0 or 1 based on the value of the VF being tested. As a result the wrong
VFs were having their VLANs cleared if they were enabled.
I have updated the code so that word represents the offset in the array.
This way we can use the modulus and xor operations and they will make sense
instead of being performed on a 4 byte aligned value.
I replaced the statement "(word % 2) ^ 1" with "~word % 2" in order to
reduce the line length as the line exceeded 80 characters with the register
name inserted. The two should be equivalent so the change should be safe.
Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X550EM_x revision check needs to check a value, not just a bit.
Use a mask and check the value. Also remove the redundant check
inside the ixgbe_enter_lplu_t_x550em, because it can only be called
when both the mac type and revision check pass.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X550 allows for up to 64 RSS queues, but the driver can have max
of 63 (-1 MSIX vector for link).
On systems with >= 64 CPUs the driver will set the redirection table
for all 64 queues which will result in packets being dropped.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up minor redundancy in the setting of hw_enc_features that
makes it appears that X550 uniquely has more encapsulation features
than other devices. The driver only supports one more feature, so
make it look that way. No longer set NETIF_F_SG since that is set
by the register_netdev call. Thanks to Alex Duyck for noticing this
slight confusion.
Reported-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ethtool reports backplane type interfaces as 1000/10000baseT link modes.
This has been corrected to report the media as KR, KX or KX4 based on the
backplane interface present.
Signed-off-by: Veola Nazareth <veola.nazareth@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
adapter->rx_itr_setting is not a mask so check it with == instead of &
do not default to 12K interrupts in ixgbevf_set_itr()
There should be no functional effect from these changes.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the same patch as for ixgbe but applied differently according to
busy polling. See commit 5d6002b7b8 ("ixgbe: Fix handling of NAPI
budget when multiple queues are enabled per vector")
Signed-off-by: William Dauchy <william@gandi.net>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the return value of platform_get_irq on failure.
A simplified version of the semantic match that finds the two cases where
no error code is returned at all is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull rdma fixes from Doug Ledford:
"Three late 4.4-rc fixes.
The first two were very small in terms of number of lines, the third
is more lines of change than I like this late in the cycle, but there
are positive test results from Avagotech and from my own test setup
with the target hardware, and given the problem was a 100% failure
case, I sent it through.
- A previous patch updated the mlx4 driver to use vmalloc when there
was not enough memory to get a contiguous region large enough for
our needs, so we need kvfree() whenever we free that item. We
missed one place, so fix that now.
- A previous patch added code to match incoming packets against a
specific device, but failed to compensate for devices that have
both InfiniBand and Ethernet ports. Fix that.
- Under certain vlan conditions, the ocrdma driver would fail to
bring up any vlan interfaces and would print out a circular locking
failure. Fix that"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
RDMA/be2net: Remove open and close entry points
RDMA/ocrdma: Depend on async link events from CNA
RDMA/ocrdma: Dispatch only port event when port state changes
RDMA/ocrdma: Fix vlan-id assignment in qp parameters
IB/mlx4: Replace kfree with kvfree in mlx4_ib_destroy_srq
IB/cma: cma_match_net_dev needs to take into account port_num
Recently Dough Ledford reported a deadlock happening
between ocrdma-load sequence and NetworkManager service
issueing "open" on be2net interface.
The deadlock happens when any be2net hook (e.g. open/close) is called
in parallel to insmod ocrdma.ko.
A. be2net is sending administrative open/close event to ocrdma holding
device_list_mutex. It does this from ndo_open/ndo_stop hooks of be2net.
So sequence of locks is rtnl_lock---> device_list lock
B. When new ocrdma roce device gets registered, infiniband stack now
takes rtnl_lock in ib_register_device() in GID initialization routines.
So sequence of locks in this path is device_list lock ---> rtnl_lock.
This improper locking sequence causes deadlock.
In order to resolve the above deadlock condition, ocrdma intorduced a
patch to stop listening to administrative open/close events generated from
be2net driver. It now depends on link-state-change async-event generated from
CNA. This change leaves behind dead code which used to generate administrative
open/close events. This patch cleans-up all that dead code from be2net.
Reported-by: Doug Ledford <dledford@redhat.com>
CC: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
