The patch add the customize setting for Dell Dino project.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We assign rt286->codec in rt286_probe. If rt286_jack_detect is
invoked before rt286_probe, rt286->codec will be NULL and cause
a kernel panic.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
this patch fixes following sparse warning:
ts3a227e.c:222:5: warning: symbol 'ts3a227e_enable_jack_detect' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To quote from section 1.3.1 of the data sheet:
The SGTL5000 has an internal reset that is deasserted
8 SYS_MCLK cycles after all power rails have been brought
up. After this time, communication can start
...
1.0us represents 8 SYS_MCLK cycles at the minimum 8.0 MHz SYS_MCLK.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Disables GPIO support and LINE2 input and renames Mic3 input to Mic2,
if tlv320aic3104 mode is seleced. Devicetree binding document is
updated accordingly.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Shift the I2S mode value by the necessary amount before writing the
registers. This makes Right Justified and PCM mode work in addition to
the default Left Justified mode.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the issue introduced by:
3684940933 ASoC: tlv320aic3x: Add TDM support
The CTRLC register were not receiving the correct delay configuration,
which will corrupt DSP_A audio mode.
Fixes: 3684940933 (ASoC: tlv320aic3x: Add TDM support)
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This was overlooked in the late change to remove the I2S padding bits
from S24_LE mode. The patch also limits S32_LE mode to 384kHz, the
maximum according to the datasheets.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5677 codec has gained code that requires SPI to work correctly,
but there is no provision in Kconfig to prevent the driver from
being used when SPI is disabled or a loadable module, resulting
in this build error:
sound/built-in.o: In function `rt5677_spi_write':
:(.text+0xa7ba0): undefined reference to `spi_sync'
sound/built-in.o: In function `rt5677_spi_driver_init':
:(.init.text+0x253c): undefined reference to `spi_register_driver'
ERROR: "spi_sync" [sound/soc/codecs/snd-soc-rt5677-spi.ko] undefined!
ERROR: "spi_register_driver" [sound/soc/codecs/snd-soc-rt5677-spi.ko] undefined!
This makes the SPI portion of the driver depend on the SPI subsystem,
and disables the function that uses SPI for firmware download if SPI
is disabled. The latter may not be the correct solution, but I could
not come up with a better one.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: af48f1d08a ("ASoC: rt5677: Support DSP function for VAD application")
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM8904 and WM8918 has the same data type, while the WM8912
has different data type. So, use the data in dt ids table to
distinguish them.
Signed-off-by: Alexander Morozov <linux@meltdown.ru>
[voice.shen@atmel.com: add code to distinguish device type]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PLL introduces jitter, which in turn introduces noice if used
to clock the DAC. Thus, avoid the PLL output, and use the PLL input
to drive the DAC clock, if possible.
This is described for the PCM5142/PCM5242 chips in the answers to the
forum post "PCM5142/PCM5242 DAC clock source" at the TI E2E community
pages (1).
(1) http://e2e.ti.com/support/data_converters/audio_converters/f/64/t/389994
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using the PLL in master mode requires using an external connection
between one of the GPIO pins (configured as PLL/4 output) and the
SCK pin. It also requires the external clock to be fed to some other
GPIO pin instead of the SCK pin.
This is described for the PCM5122 chip in the answers to the forum post
"PCM5122 DAC as I2S master troubles with PLL mode" at the TI E2E
community pages (1). The clocking functionality is also much better
described in the datasheet for the chip PCM5242, which seems to be
register compatible with PCM512x and PCM514x (which both have severely
lacking datasheets).
(1) http://e2e.ti.com/support/data_converters/audio_converters/f/64/t/267830
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use register field names from the seemingly compatible PCM5242 datasheet,
as the PCM512x and PCM514x datasheets are severly lacking.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Give the output disable sequence a chance to fully complete, otherwise
there is a danger we may remove the clock before it is finished
resulting in a pop noise. The delay for each output must be cumulative
and these are coalesced into a single delay.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Add description for the driver
- Add dependency on the I2C module
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
make the sta32x driver usable with device tree configs. Code is heavily based
on the sta350 driver.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The reset GPIO on the STA32X Codecs is used to reset the Codec and clear
all registers. Also taking it down puts the IC in power save mode, so
we put the device in reset mode when we go to sleep.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
use the regmap API directly rather than relying on the snd_soc_read/write
functions as this seems to be in accordance with common practice.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IDE bit in the CONFF register is the third bit not the fourth.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Asus T100TAF uses ACPI ID "10EC5642" for its audio codec. I suppose it is
updated ACPI ID for the RT5642 codec since some earlier platforms are using
"10EC5640" with the RT5642 too.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The purpose of rt286_adc_event is to mute/numnte the ADC mixer.
However, it will also set the capture volume to default value.
As a result, "ADC0 Capture Volume" is not working if it is set
before capture start. This patch remove rt286_adc_event and add
"ADC0 Capture Switch" to mute/unmute ADC mixer.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm97xx touchscreen driver binds itself to the snd_ac97 device that gets
registered by the CODEC driver and expects that the device has already been
reset. Before commit 6794f709b7 ("ASoC: ac97: Drop delayed device
registration") the device was only registered after the probe function of
the CODEC driver had finished running, but starting with the mentioned
commit the device is registered as soon as snd_soc_new_ac97_codec() is
called. This causes the touchscreen driver to no longer work. Modify the
CODEC drivers to use snd_soc_alloc_ac97_codec() instead of
snd_soc_new_ac97_codec() and make sure that the AC'97 device is reset before
the snd_ac97 device gets registered.
Fixes: 6794f709b7 ("ASoC: ac97: Drop delayed device registration")
Reported-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
