Modify the RT5645 driver to parse platform data from device tree. This is
missing from previous patch in sound/soc/codecs/rt5645.c, that was present
in v3.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch separates the IO function from the rt286. It is prepared to share
for new chips that support the same IO function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit ea178d1456 ("ASoC: tas2552: Make the enable-gpio really optional")
makes enable-gpio optional. devm_gpiod_get_optional() is the better
function for optional gpio, so let's switch to use it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds some debugfs nodes to get information
about the currently running firmware.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we have a codec_probe stage initialization in the wm_adsp
driver, we can make the wm_adsp driver create its own ALSA controls
instead of having that responsibility pushed to every codec driver.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the only init function in wm_adsp is called by the
codec driver early in its probe before the codec has been
registered with SOC.
This patch adds stubs for the codec_probe and codec_remove stages
and calls them from WM5102 and WM5110 codec drivers. This allows us
to hang anything that needs setup during the codec probe stage off
these functions without further modification of the codec drivers.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: Updates for v4.2
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
Register RT5650_TDM_CTRL_4(0x7A) is readable and used for mixer
setting. It should be added in rt5645_readable_register function.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5645_enable_push_button_irq uses snd_soc_dapm_*_unlocked
functions, so it needs to lock the required dapm mutex.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The set of supported sample rates depends on the master clock supplied
to the codec. Allow the machine driver to set the required master clock
in hw_params().
Signed-off-by: Sergej Sawazki <ce3a@gmx.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In tas2552_sw_shutdown() tas_data is used while the rest of the driver uses
tas2552 when dealing with the 'struct tas2552_data'
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Double semicolon was added by the following commit:
ea178d1456 ASoC: tas2552: Make the enable-gpio really optional
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The module can not be loaded again after it has been removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Align the numbers in the header file to the same column.
At the same time change the wrapping of CFG_2 register write in the probe
function to be uniform with the other calls.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct the bit definition so the code will change the bits what it
supposed to change. Also rename the register define to
TAS2552_BOOST_APT_CTRL.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Do not write to DOUT Tristate register at probe time, specially not write
data which is defined to be used in Output Data Register.
Fix the defines for the Output Data Register and correct the register write
at probe time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
'DIN source' enum can be used to select the DIN Source (muted, left, right
or average of left and right channels).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Do not restrict the sampling rate to 44.1/48KHz. The pll_clk clock should
be (sampling rate * 512) in all cases.
Correct the J.D calculation (the D part was incorrectly calculated).
Restore PLL enable status after we are done with the configuration.
Implement hardware constraint handling towards the pll_clkin:
if D != 0 (in J.D) then 1.1MHz <= pll_clkin <= 9.2MHz needs to be checked.
If the PLL setup does not met with this constraint, fall back to BCLK as
reference clock, if BCLK fails, use the internal 1.8MHz clock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of hard wiring the WCLK frequency at probe time do it runtime.
The hard wired 88_96KHz was not even setting the correct bits since it was
defined as (1 << 6) which will change the I2S_OUT_SEL bit and will leave
the amplifier configured for 8KHz.
At the same time clean up and fix the CFG3 register bits.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Configure the word length based on the params_width of the stream.
Also configure the clock per frame value which is used when tas2552 is bus
master.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Certain sequence need to be followed in order to have smooth power up and
power down performance.
Execute this sequence via DAPM_POST widget.
Remove patching the RESERVED_0D register at probe time since it has to be
handled every time when we stop or start the amplifier.
In order to be able to execute the sequence at the correct time, the driver
need to request to ignore the pmdown time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The last parameter for DECLARE_TLV_DB_SCALE() is to tell if the gain will
be muted or not when it is set to raw 0. IN this case it is not muted.
The PGA_GAIN is in 0-4 bits in the register. Fix the offset in the
SOC_SINGLE_TLV() for this.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The strings should be: 'static const char * const tas2552_input_texts[]'
SOC_DAPM_ENUM should have "Route" in place of xname and no need to have it
as an array.
Also align the parameters.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TDM support is achieved using DSP transfer mode and setting a programmable
offset which specifies where data begins with respect to the frame sync.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use names from the datasheet for the definitions.
Correct the data format definitions since they were not correct.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP_A mode require one bit delay from the FS, DSP_B is without data delay.
When checking the requested format, also match the bit and fs inversion
flag along with the format since it is not possible to change inversion.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of hard wiring the PLL_CLKIN and PDM_CLK to be sourced from BCLK add
proper clock configuration via the set_dai_sysclk callback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prevents frequent panic on boot, if the irq handler rt5645_irq
gets called before the workqueue rt5645_jack_detect_work is
initialized.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
MCLK is one of the possible source for the pll_clkin frequency. Make this
clear by renaming the variable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function name and parameters of:
tas2552_sw_shutdown(struct tas2552_data *tas_data, int sw_shutdown)
implies that if sw_shutdown is 1 we should be entering to the software
shutdown mode.
The code can be simplified as well within the function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initialize the cfg1_reg to 0 and set the mute bit only when it is needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the _MASK postfix of the bit definitions, collect the CFG1 bit
definition in one place and correct the bit shifts at the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PDM clock can be selected via bit0-1.
PDM_DATA_ES bit is at bit2.
The code were trying to select BCLK as PDM reference clock but instead
it was selecting PLL and set the DATA_ES bit to 1.
Selecting the PLL output as reference clock as default does make sense,
but the driver should not change the PDM data edge.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SOC_DAPM_SINGLE("Playback AMP", ..) should not be under kcontrols. It
causes kernel crash (NULL pointer) when the mixers are listed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
