The cdn_dp_pd_event_work is using drm_helper_hpd_irq_event to update the
connector status, this function is used to update all connectors of
drm_device. Therefore, the detect of other connector will be call, when
cdn_dp_pd_event_work is triggered, every time. It is not necessary, and
it may cause system crash. replace drm_helper_hpd_irq_event with
drm_kms_helper_hotplug_event, only update cdn-dp status.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
If the driver is in suspended mode, the dp block may be disabled, and
chip registers may not be accessible. Yet, the worker may be triggered
in this situation by an extcon event. If that happens, the following crash
will be seen.
cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] *ERROR* Enable dp failed -19
cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] Connected, not enabled. Enabling cdn
Bad mode in Error handler detected, code 0xbf000002 -- SError
CPU: 1 PID: 10357 Comm: kworker/1:2 Not tainted 4.4.21-05903-ge0514ea #1
Hardware name: Google Kevin (DT)
Workqueue: events cdn_dp_pd_event_work
task: ffffffc0cda67080 ti: ffffffc0b9b80000 task.ti: ffffffc0b9b80000
PC is at cdn_dp_clock_reset+0x30/0xa8
LR is at cdn_dp_enable+0x1e0/0x69c
...
Call trace:
[<ffffffc0005a7e24>] cdn_dp_pd_event_work+0x58/0x3f4
[<ffffffc0002397f0>] process_one_work+0x240/0x424
[<ffffffc00023a28c>] worker_thread+0x2fc/0x424
[<ffffffc00023f5fc>] kthread+0x10c/0x114
[<ffffffc000203dd0>] ret_from_fork+0x10/0x40
Problem is two-fold: The worker should not run while suspended, and the
suspend function should not call cdn_dp_disable() while the worker is
running.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
If no monitor is connected, suspend/resume cycles result in firmware
load errors because the driver attempts to load the firmware while
the system is in suspend state. This results in a kernel warning and
traceback.
Loading the firmware during boot fixes the problem. Note that we can not
just call schedule_work conditionally in cdn_dp_pd_event() if the insertion
status changed. The problem would still be seen if a monitor is connected
for the first time during suspend.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Add support for cdn DP controller which is embedded in the rk3399
SoCs. The DP is compliant with DisplayPort Specification,
Version 1.3, This IP is compatible with the rockchip type-c PHY IP.
There is a uCPU in DP controller, it need a firmware to work,
please put the firmware file to /lib/firmware/rockchip/dptx.bin. The
uCPU in charge of aux communication and link training, the host use
mailbox to communicate with the ucpu.
The dclk pin_pol of vop must not be invert for DP.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
[seanpaul fixed up some races between the worker and modeset]
[seanpaul squashed ~15 commits from chromium.org gerrit]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[groeck fixed compilation errors when building as module]
Signed-off-by: Guenter Roeck <groeck@chromium.org>
rockchip_drm_framebuffer_init is only used in one case, in
rockchip_drm_fbdev.c, where its return value is tested using IS_ERR. To
enable propagating the reason for the error, change the definition so that
it returns an ERR_PTR value.
Problem found with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
The setting of vop registers need a reg_done writing to take effect.
In vop_enable the vop return to work by by restoring registers, but the
registers do not take effect immediately, it should a vop_cfg_done
after it. The same thing is needed by windows_disabled in
vop_crtc_disable.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
The audio chicken bit (register offset 0x62f38) seems required to make
DP audio working on some machines. At least, on Dell Wyse 3040, I
failed to get the audio unless this bit is set once.
Strangely, the bit seems necessary only once, and it persists after
that, even some power-off cycles. The register is supposedly
write-only, so it's no evidence whether the bit keeps effect
persistently. But, judging from the experiment, it looks enough to
set it up once at the device initialization.
The patch is basically a cut from the original patch by Pierre-Louis
Bossart.
v1->v2: drop read since it's a write-only reg.
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
two amd fixes.
* 'drm-fixes-4.10' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Fix vram_size/visible values in DRM_RADEON_GEM_INFO ioctl
drm/amdgpu/si: fix crash on headless asics
here's Maarten's backport of the vma fixes for v4.10.
* tag 'topic/vma-fix-for-4.10-2017-02-02' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Track pinned vma in intel_plane_state
drm/atomic: Unconditionally call prepare_fb.
It includes code cleanups from Bhumika and Liviu, a significant shader
performance fix and additions to the cmdstream validator from Wladimir
and the addition of a cmdbuf suballocator by myself.
The suballocator improves performance on all chips by reducing the CPU
overhead of the kernel driver and side steps the GC3000 FE MMU flush
erratum, now making the workarounds in IOVA allocation we had before
unnecessary, which results in a nice cleanup of the code in that area.
* 'drm-etnaviv-next' of https://git.pengutronix.de/git/lst/linux:
drm/etnaviv: Remove duplicate header file include
Revert "drm/etnaviv: trick drm_mm into giving out a low IOVA"
drm/etnaviv: add cmdbuf suballocator
drm/etnaviv: get cmdbuf physical address through the cmdbuf abstraction
drm/etnaviv: wire up iova handling in new cmdbuf abstraction
drm/etnaviv: move cmdbuf de-/allocation into own file
drm/etnaviv: always flush MMU TLBs on map/unmap
drm/etnaviv: constify etnaviv_iommu_ops structures
drm/etnaviv: set up initial PULSE_EATER register
drm/etnaviv: add new GC3000 sensitive states
We don't add any fences do the buffer, but just use it's address.
Additional to that we don't need a duplicates list here.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead of receiving the num_crts as a parameter, we can read it
directly from the mode_config structure. I audited the drivers that
invoke this helper and I believe all of them initialize the mode_config
struct accordingly, prior to calling the fb_helper.
I used the following coccinelle hack to make this transformation, except
for the function headers and comment updates. The first and second
rules are split because I couldn't find a way to remove the unused
temporary variables at the same time I removed the parameter.
// <smpl>
@r@
expression A,B,D,E;
identifier C;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
expression A,B,C,D,E;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
identifier r.C;
type T;
expression V;
@@
- T C;
<...
when != C
- C = V;
...>
// </smpl>
Changes since v1:
- Rebased on top of the tip of drm-misc-next.
- Remove mention to sti since a proper fix got merged.
Suggested-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202162640.27261-1-krisman@collabora.co.uk
vram_size is supposed to be the total amount of VRAM that can be used by
userspace, which corresponds to the TTM VRAM manager size (which is
normally the full amount of VRAM, but can be just the visible VRAM when
DMA can't be used for BO migration for some reason).
The above was incorrectly used for vram_visible before, resulting in
generally too large values being reported.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some state is coupled into the device lifetime outside of the
load/unload timeframe and requires teardown during final unreference
from drm_dev_release(). For example, dmabufs hold both a device and
module reference and may live longer than expected (i.e. the current
pattern of the driver tearing down its state and then releasing a
reference to the drm device) and yet touch driver private state when
destroyed.
v2: Export drm_dev_fini() and move the responsibility for finalizing the
drm_device and freeing it to the release callback. (If no callback is
provided, the core will call drm_dev_fini() and kfree(dev) as before.)
v3: Remember to add drm_dev_fini() to drm_drv.h
v4: Tidy language for kerneldoc
v5: Cross reference from drm_dev_init() to note that driver->release()
allows for arbitrary embedding.
v6: Refer to driver data rather than driver state, as state is now
becoming associated with the struct drm_atomic_state and friends.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[danvet: Use the proper reference for struct members, which is
&drm_driver.release.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202093632.31017-1-chris@chris-wilson.co.uk
MHL3 protocol requires registry adjustments depending on chosen video mode.
Necessary information is gathered in mode_fixup callback. In case of HDMI
video modes driver should also send special AVI and MHL3 infoframes.
The patch introduces generic helpers for handling MHL3 infoframes, in
case of appearance of other users of MHL3 infoframes these function can
be moved to common library.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-21-git-send-email-a.hajda@samsung.com
