Per PCI specification, Configuration Register has different types (RO,
RW, RW1C, Rsvd). For RO Register bits are read-only and cannot be
altered by software. For RW1C Register bits indicate status when read.
A Set bit indicates a status event which is Cleared by writing a 1b.
Writing a 0b to RW1C bits has no effect. Reserved Register is for future
implementations, and they are read-only and must return zero when read.
Current vGPU configuration write emulation just copy the value as it is.
So we haven't emulated RO, RW1C and Rsvd Registers correctly. This patch
is following the Spec to correct emulation logic. We add a function
vgpu_cfg_mem_write to wrap the access to vGPU configuration memory.
The write function uses a RW Register bitmap to avoid RO bits be
overwritten, and emulate RW1C behavior for the particular status Register.
v2:
new = src[i] --> new = src[i] & mask (zhenyu)
Signed-off-by: Changbin Du <changbin.du@intel.com>
Cc: Xiaoguang Chen <xiaoguang.chen@intel.com>
Cc: Zhiyuan Lv <zhiyuan.lv@intel.com>
Cc: Min He <min.he@intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Currently i915 has a request replay mechanism which can make sure
the request can be replayed after a GPU reset. With this mechanism,
gvt should wait until the GVT request seqno passed before complete
the current workload. So that there should be a context switch interrupt
come before gvt free the workload. In this way, workload lifecylce
matches with the i915 request lifecycle. The workload can only be freed
after the request is completed.
v2: use gvt_dbg_sched instead of gvt_err to print when wait again
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
The THC63LVDM83D is a transparent LVDS encoder. Unlike dumb LVDS
encoders it can be controlled through a few pins (power down, LVDS
swing, clock edge selection) and requires power supplies. However, on
several boards where the device is used neither the control pins nor the
power supply are controllable.
To avoid developing a separate device-specific driver add a
"thine,thc63lvdm83d" compatible entry to the lvds-encoder driver. This
will allow supporting many THC63LVDM83D-based boards easily, while
allowing future development of an thc63lvdm83d driver when needed
without breaking backward compatibility.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302104728.7150-5-laurent.pinchart+renesas@ideasonboard.com
The ADV7123 is a transparent VGA DAC. Unlike dumb VGA DACs it can be
controlled through a power save pin, and requires a power supply.
However, on most boards where the device is used neither the power save
signal nor the power supply are controllable.
To avoid developing a separate device-specific driver add an
"adi,adv7123" compatible entry to the dumb-vga-dac driver. This will
allow supporting most ADV7123-based boards easily, while allowing future
development of an adv7123 driver when needed without breaking backward
compatibility.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302104728.7150-4-laurent.pinchart+renesas@ideasonboard.com
Pull sched.h split-up from Ingo Molnar:
"The point of these changes is to significantly reduce the
<linux/sched.h> header footprint, to speed up the kernel build and to
have a cleaner header structure.
After these changes the new <linux/sched.h>'s typical preprocessed
size goes down from a previous ~0.68 MB (~22K lines) to ~0.45 MB (~15K
lines), which is around 40% faster to build on typical configs.
Not much changed from the last version (-v2) posted three weeks ago: I
eliminated quirks, backmerged fixes plus I rebased it to an upstream
SHA1 from yesterday that includes most changes queued up in -next plus
all sched.h changes that were pending from Andrew.
I've re-tested the series both on x86 and on cross-arch defconfigs,
and did a bisectability test at a number of random points.
I tried to test as many build configurations as possible, but some
build breakage is probably still left - but it should be mostly
limited to architectures that have no cross-compiler binaries
available on kernel.org, and non-default configurations"
* 'WIP.sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (146 commits)
sched/headers: Clean up <linux/sched.h>
sched/headers: Remove #ifdefs from <linux/sched.h>
sched/headers: Remove the <linux/topology.h> include from <linux/sched.h>
sched/headers, hrtimer: Remove the <linux/wait.h> include from <linux/hrtimer.h>
sched/headers, x86/apic: Remove the <linux/pm.h> header inclusion from <asm/apic.h>
sched/headers, timers: Remove the <linux/sysctl.h> include from <linux/timer.h>
sched/headers: Remove <linux/magic.h> from <linux/sched/task_stack.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/init.h>
sched/core: Remove unused prefetch_stack()
sched/headers: Remove <linux/rculist.h> from <linux/sched.h>
sched/headers: Remove the 'init_pid_ns' prototype from <linux/sched.h>
sched/headers: Remove <linux/signal.h> from <linux/sched.h>
sched/headers: Remove <linux/rwsem.h> from <linux/sched.h>
sched/headers: Remove the runqueue_is_locked() prototype
sched/headers: Remove <linux/sched.h> from <linux/sched/hotplug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/debug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/nohz.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/stat.h>
sched/headers: Remove the <linux/gfp.h> include from <linux/sched.h>
sched/headers: Remove <linux/rtmutex.h> from <linux/sched.h>
...
On VLV/CHV enabling sprite0 when sprite1 has already been enabled may
lead to an underrun. This only happens when sprite0 FIFO size is zero
prior to enabling it. Hence an effective workaround is to always
allocate at least one cacheline for sprite0 when sprite1 is active.
I've not observed this sort of failure during any other type of plane
enable/disable sequence.
v2: s/noninverted/raw/ for consistency with other platforms
Testcase: igt/kms_plane_blinker
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-14-ville.syrjala@linux.intel.com
Remove crtc->wm.cxsr_allowed and just rely on crtc_state->disable_cxsr
instead. This was used only by vlv/chv to indicate whether to enable
cxsr in the wm computation. That doesn't really work anymore, and as far
as the optimal watermarks go we'll just consider the number of planes
and the current pipe, and for the intermediate watermarks we'll also
start to consider disable_cxsr which is set appropriately when planes
are being enabled/disabled.
We'll also flip over the crtc_state->wm.need_postvbl_update setup so
that it's the wm code that will set it. Previously the generic code set
it up, and then the wm code cleared it again if it thought it's not
needed after all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-11-ville.syrjala@linux.intel.com
Since the watermark registers arent double buffered on VLV/CHV, we'll
need to play around with intermediate watermarks same was as we do on
ILK-BDW.
The watermark registers on VLV/CHV contain inverted values, so to find
the intermediate watermark value we just take the minimum of the
active and optimal values. This also means that, unlike ILK-BDW,
there's no chance that we'd fail to find a working intermediate
watermarks. As long as both the active and optimal watermarks are valid
the intermediate watermarks will come out valid as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-10-ville.syrjala@linux.intel.com
Check whether anything relevant has actually change when we compute new
watermarks for each plane in the state. If the watermarks for no
primary/sprite planes changed we don't have to recompute the FIFO split
or reprogram the DSBARB registers. And even the cursor watermarks didn't
change we can skip the merge+invert step between all the planes on
the pipe as well.
v2: s/noninverted/raw/ for consistency with other platforms
v3: Drop duplicated vlv_get_fifo_size() call during init
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-9-ville.syrjala@linux.intel.com
Start computing the vlv/chv watermarks the atomic way, from the
.compute_pipe_wm() hook. We'll recompute the actual watermarks
for only planes that are part of the state, the other planes will
keep their watermark from the last time it was computed.
And the actual watermark programming will happen from the
.initial_watermarks() hook. For now we'll just compute the
optimal watermarks, and we'll hook up the intermediate
watermarks properly later.
The DSPARB registers responsible for the FIFO paritioning are
double buffered, so they will be programming from
intel_begin_crtc_commit().
v2: s/noninverted/raw/ for consistency with other platforms
s/vlv_plane_wm_set/vlv_raw_plane_wm_set/ for clarity
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-8-ville.syrjala@linux.intel.com
Let's compute the watermarks first and the FIFO size second. This way we
can make sure the FIFO split is the most accommodating to the watermarks.
Previously we could have potentially computed a FIFO split that couldn't
accommodate the PM2 watermarks simply due to a bad split even if the
total FIFO size would have been sufficient.
It'll also allow us to avoid recomputing the wms for all planes whenever
the FIFO split would change. Thus we don't have to add any extra planes
to the state when the FIFO needs to be repartitioned.
To help with this we'll keep around copies of the non-inverted
watermarks in the crtc state. For now that doesn't help too much, but
once we start to do the watermark computation only for the planes
that change we'll need the non-inverted values around for the other
planes.
v2: s/noninverted/raw/ for consistency with other platforms
Fix the memset() of the "raw" watermarks
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-7-ville.syrjala@linux.intel.com
If we setup the vm size early, we can use the newly introduced
i915_vm_is_48bit() in majority of callsites wanting to know the vm size.
As we operate either with 3lvl or 4lvl page table structure,
wrap the vm size query inside a function which tells us if
4lvl setup is needed for particular vm, as the following
code uses the function names where level is noted.
v2: use_4lvl (Chris)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1488295691-9404-3-git-send-email-mika.kuoppala@intel.com
During reset_all_global_seqno() on seqno rollover, we have to update the
HWS. This causes all in flight requests to be completed, so first we
wait. However, we were only waiting for the requests themselves to be
completed and clearing out the waiter rbtrees - what I had missed was
the extra reference in execlists->port[]. Since commit fe9ae7a3bf
("drm/i915/execlists: Detect an out-of-order context switch") we can
detect when the request is retired before the context switch interrupt
is completed. The impact should be neglible outside of debugging.
Testcase: igt/gem_exec_whisper
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303121947.20482-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
