On imx53-qsb the TVE DAC regulator comes from:
- LDO7 on the board with the Dialog DA9052 PMIC
- VDAC on the board with the MC34708 PMIC
Pass them in the 'dac-supply' node.
While at it, remove the 'regulator-always-on/regulator-boot-on'
properties as the TVE driver will properly handle it.
Tested on a imx53-qsb board with a Dialog DA9052 PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since the codec is probed first, the pinctrl node should be
under the codec node.
The codec init was working for this board since U-Boot was
already setting GPIO_0 as CLKO1 but better fix it anyway.
Fixes: 3faa1bb2e8 ("ARM: dts: imx: add Boundary Devices Nitrogen6_SOM2 support")
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch fixes the following error:
sgtl5000 0-000a: Error reading chip id -6
imx-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered
imx-sgtl5000 sound: snd_soc_register_card failed (-517)
The problem was that the pinctrl group was linked to the sound driver
instead of the codec node. Since the codec is probed first, the sys_mclk
was missing and it would therefore fail to initialize.
Fixes: b32e700256 ("ARM: dts: imx: add Boundary Devices Nitrogen6_Max board")
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch provides support for Liebherr's Monitor 6 board (abverrated as
mccmon6) to Linux kernel.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LS1012A features an advanced 64-bit ARM v8 CortexA53 processor
with 32 KB of parity protected L1-I cache, 32 KB of ECC protected
L1-D cache, as well as 256 KB of ECC protected L2 cache.
Features summary
One 64-bit ARM-v8 Cortex-A53 core with the following capabilities
- Arranged as a cluster of one core supporting a 256 KB L2 cache with ECC
protection
- Speed up to 800 MHz
- Parity-protected 32 KB L1 instruction cache and 32 KB L1 data cache
- Neon SIMD engine
- ARM v8 cryptography extensions
One 16-bit DDR3L SDRAM memory controller
ARM core-link CCI-400 cache coherent interconnect
Cryptography acceleration (SEC)
One Configurable x3 SerDes
One PCI Express Gen2 controller, supporting x1 operation
One serial ATA (SATA Gen 3.0) controller
One USB 3.0/2.0 controller with integrated PHY
Following levels of DTSI/DTS files have been created for the LS1012A
SoC family:
- fsl-ls1012a.dtsi:
DTS-Include file for FSL LS1012A SoC.
- fsl-ls1012a-frdm.dts:
DTS file for FSL LS1012A FRDM board.
- fsl-ls1012a-qds.dts:
DTS file for FSL LS1012A QDS board.
- fsl-ls1012a-rdb.dts:
DTS file for FSL LS1012A RDB board.
Signed-off-by: Harninder Rai <harninder.rai@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DryIce block on i.MX25 chipset uses two interrupts: A normal and a
security violation interrupt. Add the security violation interrupt to
the list, it is optional.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In generic_load_microcode(), curr_mc_size is the size of the last
allocated buffer and since we have this performance "optimization"
there to vmalloc a new buffer only when the current one is bigger,
curr_mc_size ends up becoming the size of the biggest buffer we've seen
so far.
However, we end up saving the microcode patch which matches our CPU
and its size is not curr_mc_size but the respective mc_size during the
iteration while we're staring at it.
So save that mc_size into a separate variable and use it to store the
previously found microcode buffer.
Without this fix, we could get oops like this:
BUG: unable to handle kernel paging request at ffffc9000e30f000
IP: __memcpy+0x12/0x20
...
Call Trace:
? kmemdup+0x43/0x60
__alloc_microcode_buf+0x44/0x70
save_microcode_patch+0xd4/0x150
generic_load_microcode+0x1b8/0x260
request_microcode_user+0x15/0x20
microcode_write+0x91/0x100
__vfs_write+0x34/0x120
vfs_write+0xc1/0x130
SyS_write+0x56/0xc0
do_syscall_64+0x6c/0x160
entry_SYSCALL64_slow_path+0x25/0x25
Fixes: 06b8534cb7 ("x86/microcode: Rework microcode loading")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/4f33cbfd-44f2-9bed-3b66-7446cd14256f@ce.jp.nec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since on Intel we're required to do CPUID(1) first, before reading
the microcode revision MSR, let's add a special helper which does the
required steps so that we don't forget to do them next time, when we
want to read the microcode revision.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/20170109114147.5082-4-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Intel supplies the microcode revision value in MSR 0x8b
(IA32_BIOS_SIGN_ID) after CPUID(1) has been executed. Execute it each
time before reading that MSR.
It used to do sync_core() which did do CPUID but
c198b121b1 ("x86/asm: Rewrite sync_core() to use IRET-to-self")
changed the sync_core() implementation so we better make the microcode
loading case explicit, as the SDM documents it.
Reported-and-tested-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/20170109114147.5082-3-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Back to regular -misc pulls with reasonable sizes:
- dma_fence error clarification (Chris)
- drm_crtc_from_index helper (Shawn), pile more patches on the m-l to roll
this out to drivers
- mmu-less support for fbdev helpers from Benjamin
- piles of kerneldoc work
- some polish for crc support from Tomeu and Benjamin
- odd misc stuff all over
* tag 'drm-misc-next-2017-01-09' of git://anongit.freedesktop.org/git/drm-misc: (48 commits)
dma-fence: Introduce drm_fence_set_error() helper
dma-fence: Wrap querying the fence->status
dma-fence: Clear fence->status during dma_fence_init()
drm: fix compilations issues introduced by "drm: allow to use mmuless SoC"
drm: Change the return type of the unload hook to void
drm: add more document for drm_crtc_from_index()
drm: remove useless parameters from drm_pick_cmdline_mode function
drm: crc: Call wake_up_interruptible() each time there is a new CRC entry
drm: allow to use mmuless SoC
drm: compile drm_vm.c only when needed
fbmem: add a default get_fb_unmapped_area function
drm: crc: Wait for a frame before returning from open()
drm: Move locking into drm_debugfs_crtc_crc_add
drm/imx: imx-tve: Remove unused variable
Revert "drm: nouveau: fix build when LEDS_CLASS=m"
drm: Add kernel-doc for drm_crtc_commit_get/put
drm/atomic: Fix outdated comment.
drm: reference count event->completion
gpu: drm: mgag200: mgag200_main:- Handle error from pci_iomap
drm: Document deprecated load/unload hook
...
Pull networking fixes from David Miller:
1) Fix dumping of nft_quota entries, from Pablo Neira Ayuso.
2) Fix out of bounds access in nf_tables discovered by KASAN, from
Florian Westphal.
3) Fix IRQ enabling in dp83867 driver, from Grygorii Strashko.
4) Fix unicast filtering in be2net driver, from Ivan Vecera.
5) tg3_get_stats64() can race with driver close and ethtool
reconfigurations, fix from Michael Chan.
6) Fix error handling when pass limit is reached in bpf code gen on
x86. From Daniel Borkmann.
7) Don't clobber switch ops and use proper MDIO nested reads and writes
in bcm_sf2 driver, from Florian Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
net: dsa: bcm_sf2: Utilize nested MDIO read/write
net: dsa: bcm_sf2: Do not clobber b53_switch_ops
net: stmmac: fix maxmtu assignment to be within valid range
bpf: change back to orig prog on too many passes
tg3: Fix race condition in tg3_get_stats64().
be2net: fix unicast list filling
be2net: fix accesses to unicast list
netlabel: add CALIPSO to the list of built-in protocols
vti6: fix device register to report IFLA_INFO_KIND
net: phy: dp83867: fix irq generation
amd-xgbe: Fix IRQ processing when running in single IRQ mode
sh_eth: R8A7740 supports packet shecksumming
sh_eth: fix EESIPR values for SH77{34|63}
r8169: fix the typo in the comment
nl80211: fix sched scan netlink socket owner destruction
bridge: netfilter: Fix dropping packets that moving through bridge interface
netfilter: ipt_CLUSTERIP: check duplicate config when initializing
netfilter: nft_payload: mangle ckecksum if NFT_PAYLOAD_L4CSUM_PSEUDOHDR is set
netfilter: nf_tables: fix oob access
netfilter: nft_queue: use raw_smp_processor_id()
...
Checks on the operand to VMXON are performed after the check for
legacy mode operation and the #GP checks, according to the pseudo-code
in Intel's SDM.
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
On interrupt delivery the PPR can only grow (except for auto-EOI),
so it is impossible that non-auto-EOI interrupt delivery results
in KVM_REQ_EVENT. We can therefore use __apic_update_ppr.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On PPR update, we set KVM_REQ_EVENT unconditionally anytime PPR is lowered.
But we can take into account IRR here already.
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
PPR needs to be updated whenever on every IRR read because we
may have missed TPR writes that _increased_ PPR. However, these
writes need not generate KVM_REQ_EVENT, because either KVM_REQ_EVENT
has been set already in __apic_accept_irq, or we are going to
process the interrupt right away.
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since we're already in VCPU context, all we have to do here is recompute
the PPR value. That will in turn generate a KVM_REQ_EVENT if necessary.
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This statistic can be useful to estimate the cost of an IRQ injection
scenario, by comparing it with irq_injections. For example the stat
shows that sti;hlt triggers more KVM_REQ_EVENT than sti;nop.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a guest causes a NPF which requires emulation, KVM sometimes walks
the guest page tables to translate the GVA to a GPA. This is unnecessary
most of the time on AMD hardware since the hardware provides the GPA in
EXITINFO2.
The only exception cases involve string operations involving rep or
operations that use two memory locations. With rep, the GPA will only be
the value of the initial NPF and with dual memory locations we won't know
which memory address was translated into EXITINFO2.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
LAPIC after reset is in xAPIC mode, which poses a problem for hotplug of
VCPUs with high APIC ID, because reset VCPU is waiting for INIT/SIPI,
but there is no way to uniquely address it using xAPIC.
From many possible options, we chose the one that also works on real
hardware: accepting interrupts addressed to LAPIC's x2APIC ID even in
xAPIC mode.
KVM intentionally differs from real hardware, because real hardware
(Knights Landing) does just "x2apic_id & 0xff" to decide whether to
accept the interrupt in xAPIC mode and it can deliver one interrupt to
more than one physical destination, e.g. 0x123 to 0x123 and 0x23.
Fixes: 682f732ecf ("KVM: x86: bump MAX_VCPUS to 288")
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Slow path tried to prevent IPIs from x2APIC VCPUs from being delivered
to xAPIC VCPUs and vice-versa. Make slow path behave like fast path,
which never distinguished that.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There were three calls sites:
- recalculate_apic_map and kvm_apic_match_physical_addr, where it would
only complicate implementation of x2APIC hotplug;
- in apic_debug, where it was still somewhat preserved, but keeping the
old function just for apic_debug was not worth it
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This change implements lockless access tracking for Intel CPUs without EPT
A bits. This is achieved by marking the PTEs as not-present (but not
completely clearing them) when clear_flush_young() is called after marking
the pages as accessed. When an EPT Violation is generated as a result of
the VM accessing those pages, the PTEs are restored to their original values.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MMIO SPTEs currently set both bits 62 and 63 to distinguish them as special
PTEs. However, bit 63 is used as the SVE bit in Intel EPT PTEs. The SVE bit
is ignored for misconfigured PTEs but not necessarily for not-Present PTEs.
Since MMIO SPTEs use an EPT misconfiguration, so using bit 63 for them is
acceptable. However, the upcoming fast access tracking feature adds another
type of special tracking PTE, which uses not-Present PTEs and hence should
not set bit 63.
In order to use common bits to distinguish both type of special PTEs, we
now use only bit 62 as the special bit.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
mmu_spte_update() tracks changes in the accessed/dirty state of
the SPTE being updated and calls kvm_set_pfn_accessed/dirty
appropriately. However, in some cases (e.g. when aging the SPTE),
this shouldn't be done. mmu_spte_update_no_track() is introduced
for use in such cases.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This simplifies mmu_spte_update() a little bit.
The checks for clearing of accessed and dirty bits are refactored into
separate functions, which are used inside both mmu_spte_update() and
mmu_spte_clear_track_bits(), as well as kvm_test_age_rmapp(). The new
helper functions handle both the case when A/D bits are supported in
hardware and the case when they are not.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This change adds retries into the Fast Page Fault path. Without the
retries, the code still works, but if a retry does end up being needed,
then it will result in a second page fault for the same memory access,
which will cause much more overhead compared to just retrying within the
original fault.
This would be especially useful with the upcoming fast access tracking
change, as that would make it more likely for retries to be needed
(e.g. due to read and write faults happening on different CPUs at
the same time).
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This change renames spte_is_locklessly_modifiable() to
spte_can_locklessly_be_made_writable() to distinguish it from other
forms of lockless modifications. The full set of lockless modifications
is covered by spte_has_volatile_bits().
Signed-off-by: Junaid Shahid <junaids@google.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This change adds some symbolic constants for VM Exit Qualifications
related to EPT Violations and updates handle_ept_violation() to use
these constants instead of hard-coded numbers.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When using two-dimensional paging, the mmu_page_hash (which provides
lookups for existing kvm_mmu_page structs), becomes imbalanced; with
too many collisions in buckets 0 and 512. This has been seen to cause
mmu_lock to be held for multiple milliseconds in kvm_mmu_get_page on
VMs with a large amount of RAM mapped with 4K pages.
The current hash function uses the lower 10 bits of gfn to index into
mmu_page_hash. When doing shadow paging, gfn is the address of the
guest page table being shadow. These tables are 4K-aligned, which
makes the low bits of gfn a good hash. However, with two-dimensional
paging, no guest page tables are being shadowed, so gfn is the base
address that is mapped by the table. Thus page tables (level=1) have
a 2MB aligned gfn, page directories (level=2) have a 1GB aligned gfn,
etc. This means hashes will only differ in their 10th bit.
hash_64() provides a better hash. For example, on a VM with ~200G
(99458 direct=1 kvm_mmu_page structs):
hash max_mmu_page_hash_collisions
--------------------------------------------
low 10 bits 49847
hash_64 105
perfect 97
While we're changing the hash, increase the table size by 4x to better
support large VMs (further reduces number of collisions in 200G VM to
29).
Note that hash_64() does not provide a good distribution prior to commit
ef703f49a6 ("Eliminate bad hash multipliers from hash_32() and
hash_64()").
Signed-off-by: David Matlack <dmatlack@google.com>
Change-Id: I5aa6b13c834722813c6cca46b8b1ed6f53368ade
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Report the maximum number of mmu_page_hash collisions as a per-VM stat.
This will make it easy to identify problems with the mmu_page_hash in
the future.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The check in kvm_set_pic_irq() and kvm_set_ioapic_irq() was just a
temporary measure until the code improved enough for us to do this.
This changes APIC in a case when KVM_SET_GSI_ROUTING is called to set up pic
and ioapic routes before KVM_CREATE_IRQCHIP. Those rules would get overwritten
by KVM_CREATE_IRQCHIP at best, so it is pointless to allow it. Userspaces
hopefully noticed that things don't work if they do that and don't do that.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We don't treat kvm->arch.vpic specially anymore, so the setup can look
like ioapic. This gets a bit more information out of return values.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
irqchip_in_kernel() tried to save a bit by reusing pic_irqchip(), but it
just complicated the code.
Add a separate state for the irqchip mode.
Reviewed-by: David Hildenbrand <david@redhat.com>
[Used Paolo's version of condition in irqchip_in_kernel().]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Split irqchip cannot be created after creating the kernel irqchip, but
we forgot to restrict the other way. This is an API change.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ADC driver depends on REGULATOR and IIO that are not yet selected.
Current hardware boards (like stm32f429i-eval) is using fixed
regulators.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This enables the pwm-beeper module. This is used by the speaker on LEGO
MINDSTORMS EV3.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
When clock_event_device::set_state_oneshot_stopped() is not implemented,
hrtimer_cancel() can't stop the clock when there is no more timer in
the queue. So the ghost of the freshly cancelled hrtimer haunts us back
later with an extra interrupt:
<idle>-0 [002] d..2 2248.557659: hrtimer_cancel: hrtimer=ffff88021fa92d80
<idle>-0 [002] d.h1 2249.303659: local_timer_entry: vector=239
So let's implement this missing callback for the lapic clock. This
consist in calling its set_state_shutdown() callback. There don't seem
to be a lighter way to stop the clock. Simply writing 0 to APIC_TMICT
won't be enough to stop the clock and avoid the extra interrupt, as
opposed to what is specified in the specs. We must also mask the
timer interrupt in the device.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Reviewed-by: Wanpeng Li <wanpeng.li@hotmail.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: http://lkml.kernel.org/r/1483029949-6925-1-git-send-email-fweisbec@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If after too many passes still no image could be emitted, then
swap back to the original program as we do in all other cases
and don't use the one with blinding.
Fixes: 959a757916 ("bpf, x86: add support for constant blinding")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
