SoC for 4.11:
- small cleanup
* tag 'at91-ab-4.11-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: pm: remove useless extern definition
Signed-off-by: Olof Johansson <olof@lixom.net>
ARMv8 Vexpress/Juno DT updates for v4.11
1. Addition of Coresight support on Juno R1 and R2 variants
2. Addition of STM(System Trace Macrocell) support on all Juno variants
3. Removed incorrect nesting of dtsi files
4. Removed untested USB hub only available on initial Juno R0 motherboard
5. Added ETR SMMU power domain and dma-ranges property
* tag 'juno-updates-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: remove motherboard USB node
arm64: dts: juno: add ETR SMMU power domain
arm64: dts: juno: add dma-ranges property
arm64: dts: juno: add missing CoreSight STM component
arm64: dts: juno: add CoreSight support for Juno r1/r2 variants
arm64: dts: juno: refactor CoreSight support on Juno r0
arm64: dts: juno: remove dtsi nesting inside tree structure
Signed-off-by: Olof Johansson <olof@lixom.net>
Fixes for omaps for v4.10-rc cycle. Mostly a DMA regression fix for
omap1, and then a handful of trivial fixes for boards and devices to
work:
- Fixes TI wilink bluetooth strange platform data baud rate
- Remove duplicate pinmux line for am335x-icev2
- Fix omap1 dma regression
- Fix uninitialized return value for wkup_m3_ipc_probe()
- Fix Ethernet PHY binding typo for dra72-evm
- Fix init for omap5 and dra7 sata ports
- Fix mmc card detect pin for Logic PD SOM-LV
* tag 'omap-for-v4.10/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3: Fix Card Detect and Write Protect on Logic PD SOM-LV
ARM: dts: OMAP5 / DRA7: indicate that SATA port 0 is available.
ARM: dts: dra72-evm-revc: fix typo in ethernet-phy node
soc: ti: wkup_m3_ipc: Fix error return code in wkup_m3_ipc_probe()
ARM: OMAP1: DMA: Correct the number of logical channels
ARM: dts: am335x-icev2: Remove the duplicated pinmux setting
ARM: OMAP2+: Fix WL1283 Bluetooth Baud Rate
Signed-off-by: Olof Johansson <olof@lixom.net>
vs. fixed 512M before.
But this still assumes that all of memory is under IOC which may not be
true for the SoC. Improve that later when this becomes a real issue, by
specifying this from DT.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
On AXS103 release bitfiles, DMA data corruptions were seen because IOC
setup was not following the recommended way in documentation.
Flipping IOC on when caches are enabled or coherency transactions are in
flight, might cause some of the memory operations to not observe
coherency as expected.
So strictly follow the programming model recommendations as documented
in comment header above arc_ioc_setup()
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
There is one blue LED on the front of the device. Keep it lit and
configure it as panic indicator.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds pinctrl group nodes for the CTS and RTS pins of each serial
controller. This makes it possible to enable the CTS and RTS pins which
are controlled by the serial controller hardware (through the meson_uart
driver).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the missing node for the uart_AO_B port to the meson-gx.dtsi
(as this is supported by GXBB, GXL and GXM) along with the required
pinctrl pins. This is required as some boards are using it (the boards
from the Khadas VIM series for example have it exposed on the pin
headers).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit 9f24273837 ("bonding: use last_arp_rx in slave_last_rx()").
However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.
Previously, there was an accompanying comment for the last_rx member
added in commit 4dc89133f4 ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit f8ff080dac ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.
Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.
Compile-tested with allyesconfig and allmodconfig on x86 and arm.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relax ordering(RO) is one feature of 82599 NIC, to enable this feature can
enhance the performance for some cpu architecure, such as SPARC and so on.
Currently it only supports one special cpu architecture(SPARC) in 82599
driver to enable RO feature, this is not very common for other cpu architecture
which really needs RO feature.
This patch add one common config CONFIG_ARCH_WANT_RELAX_ORDER to set RO feature,
and should define CONFIG_ARCH_WANT_RELAX_ORDER in sparc Kconfig firstly.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Alexander Duyck <alexander.duyck@gmail.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This plugin detects any structures that contain __user attributes and
makes sure it is being fully initialized so that a specific class of
information exposure is eliminated. (This plugin was originally designed
to block the exposure of siginfo in CVE-2013-2141.)
Ported from grsecurity/PaX. This version adds a verbose option to the
plugin and the Kconfig.
Signed-off-by: Kees Cook <keescook@chromium.org>
Pull ARM fixes from Russell King:
"A few ARM fixes:
- fix a crash while performing TLB maintanence on early ARM SMP cores
- blacklist Scorpion CPUs for hardware breakpoints
- ARMs asm/types.h has been included as part of the UAPI due to the
way the makefiles work, move it to uapi/asm/types.h to make it
official
- fix up ftrace syscall name matching"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8613/1: Fix the uaccess crash on PB11MPCore
MAINTAINERS: update rmk's entries
ARM: put types.h in uapi
ARM: 8634/1: hw_breakpoint: blacklist Scorpion CPUs
ARM: 8632/1: ftrace: fix syscall name matching
commit d65283f7b6 added mod->arch.secstr under
CONFIG_ARC_DW2_UNWIND, but used it unconditionally which broke builds
when the option was disabled. Fix that by adjusting the #ifdef guard.
And while at it add a missing guard (for unwinder) in module.c as well
Reported-by: Waldemar Brodkorb <wbx@openadk.org>
Cc: stable@vger.kernel.org #4.9
Fixes: d65283f7b6 ("ARC: module: elide loop to save reference to .eh_frame")
Tested-by: Anton Kolesov <akolesov@synopsys.com>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
[abrodkin: provided fixlet to Kconfig per failure in allnoconfig build]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull SMP hotplug update from Thomas Gleixner:
"This contains a trivial typo fix and an extension to the core code for
dynamically allocating states in the prepare stage.
The extension is necessary right now because we need a proper way to
unbreak LTTNG, which iscurrently non functional due to the removal of
the notifiers. Surely it's out of tree, but it's widely used by
distros.
The simple solution would have been to reserve a state for LTTNG, but
I'm not fond about unused crap in the kernel and the dynamic range,
which we admittedly should have done right away, allows us to remove
quite some of the hardcoded states, i.e. those which have no ordering
requirements. So doing the right thing now is better than having an
smaller intermediate solution which needs to be reworked anyway"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu/hotplug: Provide dynamic range for prepare stage
perf/x86/amd/ibs: Fix typo after cleanup state names in cpu/hotplug
Support for Exynos4415 is going away because there are no internal nor
external users.
Since commit 46dcf0ff0d ("ARM: dts: exynos: Remove exynos4415.dtsi"),
the platform cannot be instantiated so remove also the mach code.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kukjin Kim <kgene@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
When the header is not included implicitly, we get a build failure:
arch/arm/mach-pxa/idp.c:205:22: error: field 'cdev' has incomplete type
struct led_classdev cdev;
This adds an explicit #include.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The camera_supply_dummy_device definition is shared between a780 and a910,
but only provided when the first is enabled and fails to build for a
configuration with only a910:
arch/arm/mach-pxa/ezx.c:1097:3: error: 'camera_supply_dummy_device' undeclared here (not in a function)
This moves the definition into its own section.
Fixes: 6c1b417adc ("ARM: pxa: ezx: use the new pxa_camera platform_data")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
We cannot preserve partial fields for hardware breakpoints, because
the values written by userspace to the hardware breakpoint
registers can't subsequently be recovered intact from the hardware.
So, just reject attempts to write incomplete fields with -EINVAL.
Cc: <stable@vger.kernel.org> # 3.7.x-
Fixes: 478fcb2cdb ("arm64: Debugging support")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <Will.Deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds an explicit __reserved[] field to user_fpsimd_state
to replace what was previously unnamed padding.
This ensures that data in this region are propagated across
assignment rather than being left possibly uninitialised at the
destination.
Cc: <stable@vger.kernel.org> # 3.7.x-
Fixes: 60ffc30d56 ("arm64: Exception handling")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <Will.Deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ensure that if userspace supplies insufficient data to
PTRACE_SETREGSET to fill all the registers, the thread's old
registers are preserved.
Cc: <stable@vger.kernel.org> # 4.3.x-
Fixes: 5d220ff942 ("arm64: Better native ptrace support for compat tasks")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <Will.Deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ensure that if userspace supplies insufficient data to
PTRACE_SETREGSET to fill all the registers, the thread's old
registers are preserved.
Cc: <stable@vger.kernel.org> # 3.19.x-
Fixes: 766a85d7bc ("arm64: ptrace: add NT_ARM_SYSTEM_CALL regset")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <Will.Deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ensure that if userspace supplies insufficient data to
PTRACE_SETREGSET to fill all the registers, the thread's old
registers are preserved.
Cc: <stable@vger.kernel.org> # 3.7.x-
Fixes: 478fcb2cdb ("arm64: Debugging support")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <Will.Deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The "samsung,exynos5433-mipi-video-phy" and "samsung,exynos5250-dwusb3"
DT bindings don't specify a reg property for these nodes, so having a
unit name leads to the following DTC warnings:
Node /soc/video-phy@105c0710 has a unit name, but no reg property
Node /soc/usb@15400000 has a unit name, but no reg property
Node /soc/usb@15a00000 has a unit name, but no reg property
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The first batch of Juno boards included a discrete USB controller chip
as a contingency in case of issues with the USB 2.0 IP integrated into
the SoC. As it turned out, the latter was fine, and to the best of my
knowledge the motherboard USB was never even brought up and validated.
Since this also isn't present on later boards, and uses a compatible
string undocumented and unmatched by any driver in the kernel, let's
just tidy it away for ever to avoid any confusion.
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
It is not at all clear from the documentation, but straightforward to
determine in practice, that the ETR SMMU is actually in the DEBUGSYS
power domain. Add that to the DT so that anyone brave enough to enable
said SMMU doesn't experience a system lockup on boot, especially a
sneaky one which goes away as soon as you connect an external debugger
to have a look at where it's stuck (thus powering up DEBUGSYS by other
means and allowing it to make progress again before actually halting...)
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The interconnects around Juno have a 40-bit address width, and DMA
masters have no restrictions beyond their own individual limitations.
Describe this to ensure that DT-based DMA masks get set up correctly
for all devices capable of 40-bit addressing.
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The arm64 __page_to_voff() macro takes a parameter called 'page', and
also refers to 'struct page'. Thus, if the value passed in is not
called 'page', we'll refer to the wrong struct name (which might not
exist).
Fixes: 3fa72fe9c6 ("arm64: mm: fix __page_to_voff definition")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Suggested-by: Volodymyr Babchuk <Volodymyr_Babchuk@epam.com>
Signed-off-by: Oleksandr Andrushchenko <Oleksandr_Andrushchenko@epam.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the missing CoreSight STM component definition to the
device tree of all the juno variants(r0,r1,r2)
STM component is connected to different funnels depending on Juno
platform variant.
Reviewed-and-tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mike Leach <mike.leach@linaro.org>
[sudeep.holla@arm.com: minor changelog update and reorganising the STM
node back into juno-base.dtsi to avoid duplication]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The CoreSight support added for Juno is valid for only Juno r0.
The Juno r1 and r2 variants have additional components and alternative
connection routes between trace source and sinks.
This patch builds on top of the existing r0 support and extends it to
Juno r1/r2 variants.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mike Leach <mike.leach@linaro.org>
[sudeep.holla@arm.com: minor changelog update and major reorganisation of
the common coresight components back into juno-base.dtsi to avoid
duplication, also renamed funnel node names]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Currently the Coresight components are supported only on Juno r0
variant. In preparation to add support to Juno r1/r2 variants, this
patch refactors the existing coresight device nodes so that r1/r2
support can be added easily.
It also cleans up some of the device node names which were previously
named so as they were confused as the labels rather than the node names.
Reviewed-and-tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Currently juno-clock.dtsi and juno-base.dtsi are nested badly inside
the device tree structure. It's generally good practice to ensure that
individual dtsi stand by themselves at the top of the file.
This patch removes the nesting of the above mentioned dtsi files and
makes them independent.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
While the SinA31s does have a proper 5-pin mini USB OTG port, the ID
pin does not seem to work. The pin used in the schematics is always low,
regardless of the attached OTG cable or SoC internal pin bias settings.
The v1.5 board is missing bias resistors shown in the schematics for
earlier revisions, and the connections of the remaining one does not
match the schematics either.
In addition, VBUS for this port is disconnected from the board's 5V
power rail. The board features a pad to solder jumper pins to connect
VBUS to 5V manually.
Given the above and the fact that the board has 5 more USB host ports,
it makes more sense to have the OTG port work in peripheral mode.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
SIER and SIAR are not updated correctly for some samples, so force the
use of MSR and regs->nip instead for misc_flag updates. This is done by
adding a new ppmu flag and updating the use_siar logic in
perf_read_regs() to use it, and dropping the PPMU_HAS_SIER flag.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[mpe: Rename flag to PPMU_NO_SIAR, and also drop PPMU_HAS_SIER]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We give up recovery on permanent error, simply shutdown the affected
devices and remove them. If the devices can't be put into quiet state,
they spew more traffic that is likely to cause another unexpected EEH
error. This was observed on "p8dtu2u" machine:
0002:00:00.0 PCI bridge: IBM Device 03dc
0002:01:00.0 Ethernet controller: Intel Corporation \
Ethernet Controller X710/X557-AT 10GBASE-T (rev 02)
0002:01:00.1 Ethernet controller: Intel Corporation \
Ethernet Controller X710/X557-AT 10GBASE-T (rev 02)
0002:01:00.2 Ethernet controller: Intel Corporation \
Ethernet Controller X710/X557-AT 10GBASE-T (rev 02)
0002:01:00.3 Ethernet controller: Intel Corporation \
Ethernet Controller X710/X557-AT 10GBASE-T (rev 02)
On P8 PowerNV platform, the IO path is frozen when shutdowning the
devices, meaning the memory registers are inaccessible. It is why
the devices can't be put into quiet state before removing them.
This fixes the issue by enabling IO path prior to putting the devices
into quiet state.
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use 0x10012 event code for PM_BRU_CMPL event in power9 event list
instead of current 0x40060.
Fixes: 34922527a2 ('powerpc/perf: Add power9 event list macros for generic and cache events')
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we switched to big endian page table, we never updated the hugepd
format such that it can work for both big endian and little endian
config. This patch series update hugepd format such that it is looked at
as __be64 value in big endian page table config.
This patch also switch hugepd_t.pd from signed long to unsigned long.
I did update the FSL hugepd_ok check to check for the top bit instead
of checking > 0.
Fixes: 5dc1ef858c ("powerpc/mm: Use big endian Linux page tables for book3s 64")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The generic hugetlbfs code can handle not finding the default huge page
size correctly. With HPAGE_SHIFT = 0 we see in dmesg:
hugetlbfs: disabling because there are no supported hugepage sizes
bash-4.2# echo 30 > /proc/sys/vm/nr_hugepages
bash: echo: write error: Operation not supported
Fixes: 03bb2d6590 ("powerpc: get hugetlbpage handling more generic")
Reported-by: Chris Smart <chris@distroguy.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 9b081e1080 ("powerpc: port 64 bits pgtable_cache to 32 bits")
mixed up PMD_INDEX_SIZE and PMD_CACHE_INDEX a couple of times. This
resulted in 64s/hash/4k configs to panic at boot with a false positive
error check.
Fix that and simplify error handling by moving the check to the caller.
Fixes: 9b081e1080 ("powerpc: port 64 bits pgtable_cache to 32 bits")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes commit ab8dd3aed0 ("ARM: DTS: Add minimal Support for
Logic PD DM3730 SOM-LV") where the Card Detect and Write Protect
pins were improperly configured.
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for
Logic PD DM3730 SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The current hardware is not able to run with all cores enabled at a
cluster frequency superior at 1536MHz.
But the currently shipped u-boot for the platform still reports an OPP
table with possible DVFS frequency up to 2GHz, and will not change since
the off-tree linux tree supports limiting the OPPs with a kernel parameter.
A recent u-boot change reports the boot-time DVFS around 100MHz and
the default performance cpufreq governor sets the maximum frequency.
Previous version of u-boot reported to be already at the max OPP and
left the OPP as is.
Nevertheless, other governors like ondemand could setup the max frequency
and make the system crash.
This patch disables the DVFS clock and disables cpufreq.
Fixes: 70db166a2b ("ARM64: dts: meson-gxbb: Add SCPI with cpufreq & sensors Nodes")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Some places in the kernel open-code sequences using ADRP for a symbol
another instruction using a :lo12: relocation for that same symbol.
These sequences are easy to get wrong, and more painful to read than is
necessary. For these reasons, it is preferable to use the
{adr,ldr,str}_l macros for these cases.
This patch makes use of these in entry-ftrace.S, removing open-coded
sequences using adrp. This results in a minor code change, since a
temporary register is not used when generating the address for some
symbols, but this is fine, as the value of the temporary register is not
used elsewhere.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Some places in the kernel open-code sequences using ADRP for a symbol
another instruction using a :lo12: relocation for that same symbol.
These sequences are easy to get wrong, and more painful to read than is
necessary. For these reasons, it is preferable to use the
{adr,ldr,str}_l macros for these cases.
This patch makes use of these in efi-entry.S, removing open-coded
sequences using adrp.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Some places in the kernel open-code sequences using ADRP for a symbol
another instruction using a :lo12: relocation for that same symbol.
These sequences are easy to get wrong, and more painful to read than is
necessary. For these reasons, it is preferable to use the
{adr,ldr,str}_l macros for these cases.
This patch makes use of adr_l these in head.S, removing an open-coded
sequence using adrp.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
