The libgpio code pre-sets the GPIO values for the gpio-reset in the
device tree. This results in the device being reset during bringup.
To prevent this pre-setting, use the "open-source" flag in the device
tree.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: b1aaf88 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625hr DTS file")
Fixes: 10baed1 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625xmc DTS file")
Fixes: 088e3148 ("ARM: dts: NSP: Add new DT file for bcm958522er")
Fixes: e3227c1 ("ARM: dts: NSP: Add new DT file for bcm958525er")
Fixes: 2f8bc00 ("ARM: dts: NSP: Add new DT file for bcm958622hr")
Fixes: d454c37 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Fixes: f27eacf ("ARM: dts: NSP: Add new DT file for bcm988312hr")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add and enable the third AMAC ethernet interface in the device trees for
the platforms where it is present. Also, enable amac1 on some of the
platforms where that was missing.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
QSPI device tree entries are present in bcm958625k, but missing from
bcm958522er, bcm958525er, bcm958525xmc, bcm958622hr, bcm958623hr,
bcm958625hr, and bcm988312hr. Duplicate the entry in bcm958625k for
all of those that are missing it (as they are identical).
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The QSPI entry was added out of the sequental order that the rest of the
DTSI file is in. Move it to make it fit in properly. Also, some other
entries have been added in a non-alphabetical order in the DTS files,
making them different from the other NSP DTS files. Move the relevant
peices to make it match. Finally, remove errant new lines.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the ability to reboot the bcm958625hr board via GPIO.
Unfortunately, not all of the NSP based boards use the same GPIO pin and
one doesn't have the ability to reboot via GPIO at all. So, this will
need to be specified per DTS file.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The BCM958625HR board has 2GB of RAM available. Increase the amount
from 512MB to 2GB and add the device type to the memory entry.
Fixes: 9a4865d42f ("ARM: dts: NSP: Specify RAM amount for BCM958625HR board")
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the layout of the switch ports found on the BCM958625HR reference
board. The CPU port is hooked up to the AMAC0 Ethernet controlelr
adapter, so we also enable it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Create a new device tree file for the Broadcom Northstar Plus HR SVK.
This SVK is a smaller form factor, and thus only has 2 PCI slots and 1
UART. Also, it has the ability to reboot via GPIO (instead of the
processor reset).
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
