Conflicts:
drivers/net/ethernet/chelsio/cxgb4vf/sge.c
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.
ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Split off the setting of the RSS key into its own function. This
will help when we add support for X550 which can have different
RSS keys per pool.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch will add in the new MAC defines and fit it into the switch
cases throughout the driver. New functionality and enablement support will
be added in following patches.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move setting of drop enable to support function. This not only makes the
code more readable but is also prep for following patches that add
additional MAC support.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On topologies including few levels of PCIe switching X540 can run into an
unexpected completion error. We get around this by waiting after enabling
loopback a sufficient amount of time until Tx Data Fetch is sent. We then
poll the pending transaction bit to ensure we received the completion. Only
then do we go on to clear the buffers.
Signed-of-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following commands:
modprobe ixgbe
ifconfig ethX up
ethtool -s ethX advertise 0x020
can lead to "setup link failed with code -14" error due to the setup_link
call racing with the SFP detection routine in the watchdog.
This patch resolves this issue by protecting the setup_link call with check
for __IXGBE_IN_SFP_INIT.
Reported-by: Scott Harrison <scoharr2@cisco.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The check for vfinfo is not sufficient because it does not protect
against specifying vf that is outside of sriov_num_vfs range.
All of the ndo functions have a check for it except for
ixgbevf_ndo_set_spoofcheck().
The following patch is all we need to protect against this panic:
ip link set p96p1 vf 0 spoofchk off
BUG: unable to handle kernel NULL pointer dereference at 0000000000000052
IP: [<ffffffffa044a1c1>]
ixgbe_ndo_set_vf_spoofchk+0x51/0x150 [ixgbe]
Reported-by: Thierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: Thierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is illegal to use atomic_set(&page->_count, 2) even if we 'own'
the page. Other entities in the kernel need to use get_page_unless_zero()
to get a reference to the page before testing page properties, so we could
loose a refcount increment.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consolidates the logic behind dynamically setting TXDCTL.WTHRESH
depending on interrupt throttle rate (ITR) setting regardless of BQL.
Previously TXDCTL.WTHRESH was dynamically being set only with BQL being
enabled, but we have to set it regardless of BQL when ITR is low to avoid
Tx stalls/hangs.
CC: John Greene <jogreene@redhat.com>
Reported by: Masayuki Gouji <gouji.masayuki@jp.fujitsu.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes couple of wait loops on autoneg that are not needed.
During validation we noticed that the loops always time out, so there
should be no user impact.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Convert the normal packet completion path to dev_consume_skb_any() so
packet drop profiling via dropwatch or perf top -G -e skb_kfree_skb
is not cluttered with false hits.
Compile tested only. There is a dev_kfree_skb_any() in the routine
ixgbe_ptp_tx_hwtstamp() in ixgbe_ptp.c that looks like a conversion
candidate but I wasn't familiar enough with the code to pull the
trigger.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Again, we should not be directly using netif_printk, as we have our own
error print routines that we generate. In addition, instead of using an
early return we can just use the else block of this one line if
statement.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In this case, disabling DCB is not an error. We can still function, but
we just have to let the user know. In addition, since we call this
during probe before allocating our netdevice structure, we should use
e_dev_warn instead of e_warn.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Our calculated v_budget doesn't matter except if we allocate MSI-X
vectors. We shouldn't need to calculate this outside of the function, so
don't. Instead, only calculate it once we attempt to acquire MSI-X
vectors. This helps collocate all of the MSI-X vector code together.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We already have to kfree this value if we fail, and this is only part of
MSI-X mode, so we should simply allocate the value where we need it.
This is cleaner, and makes it a lot more obvious why we are freeing it
inside of ixgbe_acquire_msix_vectors.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to how ixgbevf handles acquiring MSI-X vectors, we can return an
error code instead of relying on the flag being set. This makes it more
clear that we have failed to setup MSI-X mode, and also will make it
easier to consolidate MSI-X related code all into the single function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The netif_printk relies on our netdevice structure to be registered
already. We may call ixgbe_acquire_msix_vectors prior to registering our
netdevice, so we should not use the netdevice specific printk.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a hardware Tx timestamp is requested, an uninitialized
workqueue entry may be scheduled, especially on an 82598 adapter.
Add a check for a PTP clock to avoid that. Also only apply the
unlikely to the first term of the conditional. That will make the
rest of the checks be in the cold path.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Because bd_number is not useful anymore, so remove it from adapter struct, or
if keep it, we have to fix the boards driven counter bug in ixgbe_remove() and
ixgbe_probe() only for trivial debug purpose -- other output is enough.
Signed-off-by: Ethan Zhao <ethan.zhao@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change addresses several issues in the current ixgbe implementation of
busy poll sockets.
First was the fact that it was possible for frames to be delivered out of
order if they were held in GRO. This is addressed by flushing the GRO buffers
before releasing the q_vector back to the idle state.
The other issue was the fact that we were having to take a spinlock on
changing the state to and from idle. To resolve this I have replaced the
state value with an atomic and use atomic_cmpxchg to change the value from
idle, and a simple atomic set to restore it back to idle after we have
acquired it. This allows us to only use a locked operation on acquiring the
vector without a need for a locked operation to release it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change removes the Rx buffer allocation at the end of ixgbe_clean_rx_irq.
The reason for removing this is to avoid the extra latency introduced by the
MMIO write. This can amount to somewhere around an extra 100ns of latency and
one extra message worth of PCIe bus overhead.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves warnings produced by ixgbe in W=2 kernel
builds. There are missing-field-initializers warnings and shadow
warnings. None of these point to any deeper problem, so just
resolve them so any new warnings get analyzed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we previously called ixgbe_set_num_queues just prior to attempting
to set our interrupt scheme, it may be non obvious why we have to call
it again inside the function. Add a comment which helps make it more
obvious that we are resetting features based on the fact that we do not
have MSI-X enabled, and cannot use the previous settings.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe initiates a reset of the interface on link loss with pending Tx work
in order to clear the rings.
This patch extends the pending Tx work check to the VF interfaces with the
same purpose.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that the behavior for FDB handling is consistent
between both the SR-IOV and non-SR-IOV cases. The main change here is that we
perform bounds checking on the number of SR-IOV addresses regardless of if
SR-IOV is enabled or not as we can only support a certain number of addresses
in the hardware.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When xmit_more mode is being used and the ring is about to
become full or the stack has stopped the ring, enforce a tail
pointer write to the hw. Otherwise, we could risk a TX hang.
Code suggested by Alexander Duyck.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements the deferred tail pointer flush API for the ixgbe
driver. Similar version also proposed longer time ago by Alexander Duyck.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
All other add functions for lists have the new item as first argument
and the position where it is added as second argument. This was changed
for no good reason in this function and makes using it unnecessary
confusing.
The name was changed to hlist_add_behind() to cause unconverted code to
generate a compile error instead of using the wrong parameter order.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Ken Helias <kenhelias@firemail.de>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [intel driver bits]
Cc: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make return values more direct, eliminating some gotos and
otherwise unneeded conditionals. This also eliminates some
local variables. Also a few minor cleanups in affected code
so checkpatch won't complain.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If ixgbe_write_mbx is called and no mbx->ops.write method
exists, no error code is returned. The corresponding read
function explicitly returns an error in such a case as do
other functions, so this appears to be a minor bug. Fix
it for consistency, and generate return values directly
to make things clearer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the function ixgbe_get_swfw_sync_semaphore, an incorrect
check was treating success as failure and vice-versa. This led
to manipulating the IXGBE_SWFW_SYNC register without holding
the software semaphore first, which is an error. In addition,
if getting the REGSMP bit in the IXGBE_SW_FW_SYNC register
timed out, no error code would be returned, making the caller
think that it had successfully acquired the lock. Fix both of
those issues and clean up the function a bit, such as make the
name in the comment match the function.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Failure to acquire the semaphore would lead to a spurious release
of the semaphore in several functions. Do not release a semaphore
that you did not get.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch prevents the display of the minimum link qualification check
if we might be in a virtual machine. This check is incorrect and
misleading in this case, since we actually don't really know what the
available bandwidth is. To do so, we simply check whether each function
on the bus matches our device id. If it doesn't the most likely scenario
is that we're directly assigned to a virtual machine.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug in the misuse of the list_for_each macro to loop over every
entry in the bus_list. Instead of attempting to loop over the list from
a random entry point, go up to the bus and use the real list_head entry
point. This prevents the possible read or write of unallocated or
incorrectly addressed memory.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change some uses of strncpy to use the more appropriate strlcpy
when clearing is not needed to prevent information leakage. Also
change some length arguments to use the preferred sizeof form.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ixgbe_probe, the code at label err_dma can dereference adapter
when it has a NULL value. The check is there to avoid disabling a
disabled device. When adapter is NULL, treat it as if the device
is enabled, because it is enabled in that case.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
