Pull ARM SoC fixes from Olof Johansson:
"A slightly larger set of fixes have accrued in the last two weeks.
Mostly a collection of the usual smaller fixes:
- Marvell Armada: USB phy setup issues on Turris Mox
- Broadcom: GPIO/pinmux DT mapping corrections for Stingray, MMC bus
width fix for RPi Zero W, GPIO LED removal for RPI CM3. Also some
maintainer updates.
- OMAP: Fixlets for display config, interrupt settings for wifi, some
clock/PM pieces. Also IOMMU regression fix and a ti-sysc
no-watchdog regression fix.
- i.MX: A few fixes around PM/settings, some devicetree fixlets and
catching up with config option changes in DRM
- Rockchip: RockRro64 misc DT fixups, Hugsun X99 USB-C, Kevin display
panel settings
... and some smaller fixes for Davinci (backlight, McBSP DMA),
Allwinner (phy regulators, PMU removal on A64, etc)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
MAINTAINERS: Update the Spreadtrum SoC maintainer
MAINTAINERS: Remove Gregory and Brian for ARCH_BRCMSTB
ARM: dts: bcm2837-rpi-cm3: Avoid leds-gpio probing issue
bus: ti-sysc: Fix watchdog quirk handling
ARM: OMAP2+: Add pdata for OMAP3 ISP IOMMU
ARM: OMAP2+: Plug in device_enable/idle ops for IOMMUs
ARM: davinci_all_defconfig: enable GPIO backlight
ARM: davinci: dm365: Fix McBSP dma_slave_map entry
ARM: dts: bcm2835-rpi-zero-w: Fix bus-width of sdhci
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
mailmap: Add Simon Arlott (replacement for expired email address)
arm64: dts: rockchip: Fix override mode for rk3399-kevin panel
...
A number of fixes for this release, but mostly:
- A fixup for the A10 CSI DT binding merged during the 5.4-rc1 window
- A fix for a dt-binding error
- Addition of phy regulator delays
- The PMU on the A64 was found to be non-functional, so we've dropped it for now
* tag 'sunxi-fixes-for-5.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun7i: Drop the module clock from the device tree
dt-bindings: media: sun4i-csi: Drop the module clock
media: dt-bindings: Fix building error for dt_binding_check
arm64: dts: allwinner: a64: sopine-baseboard: Add PHY regulator delay
arm64: dts: allwinner: a64: Drop PMU node
arm64: dts: allwinner: a64: pine64-plus: Add PHY regulator delay
Link: https://lore.kernel.org/r/80085a57-c40f-4bed-a9c3-19858d87564e.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
This pull request contains Broadcom ARM-based SoC Device Tree fixes for
5.4, please pull the following:
- Stefan removes the activity LED node from the CM3 DTS since there is
no driver for that LED yet and leds-gpio cannot drive it either
* tag 'arm-soc/for-5.4/devicetree-fixes-part2' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2837-rpi-cm3: Avoid leds-gpio probing issue
Link: https://lore.kernel.org/r/20191021194302.21024-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.4, please pull the following:
- Stefan fixes the MMC controller bus-width property for the Raspberry Pi
Zero Wireless which was incorrect after a prior refactoring
* tag 'arm-soc/for-5.4/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2835-rpi-zero-w: Fix bus-width of sdhci
Link: https://lore.kernel.org/r/20191015172356.9650-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
i.MX fixes for 5.4:
- Re-enable SNVS power key for imx6q-logicpd board which was accidentally
disabled by a SoC level change.
- Fix I2C switches on vf610-zii-scu4-aib board by specifying property
i2c-mux-idle-disconnect.
- A fix on imx-scu API that reads UID from firmware to avoid kernel NULL
pointer dump.
- A series from Anson to correct i.MX7 GPT and i.MX8 USDHC IPG clock.
- A fix on DRM_MSM Kconfig regression on i.MX5 by adding the option
explicitly into imx_v6_v7_defconfig.
- Fix ARM regulator states issue for zii-ultra board, which is impacting
stability of the board.
- A correction on CPU core idle state name for LayerScape LX2160A SoC.
* tag 'imx-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
arm64: dts: zii-ultra: fix ARM regulator states
soc: imx: imx-scu: Getting UID from SCU should have response
Link: https://lore.kernel.org/r/20191017141851.GA22506@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
Fixes for omaps for v5.4-rc cycle
More fixes for omap variants:
- Update more panel options in omap2plus_defconfig that got changed
as we moved to use generic LCD panels
- Remove unused twl_keypad for logicpd-torpedo-som to avoid boot
time warnings. This is only a cosmetic fix, but at least dmesg output
is now getting more readable after all the fixes to remove pointless
warnings
- Fix gpu_cm node name as we still have a non-standard node name
dependency for clocks. This should eventually get fixed by use
of domain specific compatible property
- Fix use of i2c-mux-idle-disconnect for m3874-iceboard
- Use level interrupt for omap4 & 5 wlcore to avoid lost edge
interrupts
* tag 'omap-for-v5.4/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Use level interrupt for omap4 & 5 wlcore
ARM: dts: am3874-iceboard: Fix 'i2c-mux-idle-disconnect' usage
ARM: dts: omap5: fix gpu_cm clock provider name
ARM: dts: logicpd-torpedo-som: Remove twl_keypad
ARM: omap2plus_defconfig: Fix selected panels after generic panel changes
Link: https://lore.kernel.org/r/pull-1571242890-118432@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull networking fixes from David Miller:
"I was battling a cold after some recent trips, so quite a bit piled up
meanwhile, sorry about that.
Highlights:
1) Fix fd leak in various bpf selftests, from Brian Vazquez.
2) Fix crash in xsk when device doesn't support some methods, from
Magnus Karlsson.
3) Fix various leaks and use-after-free in rxrpc, from David Howells.
4) Fix several SKB leaks due to confusion of who owns an SKB and who
should release it in the llc code. From Eric Biggers.
5) Kill a bunc of KCSAN warnings in TCP, from Eric Dumazet.
6) Jumbo packets don't work after resume on r8169, as the BIOS resets
the chip into non-jumbo mode during suspend. From Heiner Kallweit.
7) Corrupt L2 header during MPLS push, from Davide Caratti.
8) Prevent possible infinite loop in tc_ctl_action, from Eric
Dumazet.
9) Get register bits right in bcmgenet driver, based upon chip
version. From Florian Fainelli.
10) Fix mutex problems in microchip DSA driver, from Marek Vasut.
11) Cure race between route lookup and invalidation in ipv4, from Wei
Wang.
12) Fix performance regression due to false sharing in 'net'
structure, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (145 commits)
net: reorder 'struct net' fields to avoid false sharing
net: dsa: fix switch tree list
net: ethernet: dwmac-sun8i: show message only when switching to promisc
net: aquantia: add an error handling in aq_nic_set_multicast_list
net: netem: correct the parent's backlog when corrupted packet was dropped
net: netem: fix error path for corrupted GSO frames
macb: propagate errors when getting optional clocks
xen/netback: fix error path of xenvif_connect_data()
net: hns3: fix mis-counting IRQ vector numbers issue
net: usb: lan78xx: Connect PHY before registering MAC
vsock/virtio: discard packets if credit is not respected
vsock/virtio: send a credit update when buffer size is changed
mlxsw: spectrum_trap: Push Ethernet header before reporting trap
net: ensure correct skb->tstamp in various fragmenters
net: bcmgenet: reset 40nm EPHY on energy detect
net: bcmgenet: soft reset 40nm EPHYs before MAC init
net: phy: bcm7xxx: define soft_reset for 40nm EPHY
net: bcmgenet: don't set phydev->link from MAC
net: Update address for MediaTek ethernet driver in MAINTAINERS
ipv4: fix race condition between route lookup and invalidation
...
bcm2835-rpi.dtsi defines the behavior of the ACT LED, which is available
on all Raspberry Pi boards. But there is no driver for this particual
GPIO on CM3 in mainline yet, so this node was left incomplete without
the actual GPIO definition. Since commit 025bf37725 ("gpio: Fix return
value mismatch of function gpiod_get_from_of_node()") this causing probe
issues of the leds-gpio driver for users of the CM3 dtsi file.
leds-gpio: probe of leds failed with error -2
Until we have the necessary GPIO driver hide the ACT node for CM3
to avoid this.
Reported-by: Fredrik Yhlen <fredrik.yhlen@endian.se>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Fixes: a54fe8a6cf ("ARM: dts: add Raspberry Pi Compute Module 3 and IO board")
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* Removes mediatek,physpeed property from dtsi that is useless in PHYLINK
* Use the fixed-link property speed = <2500> to set the phy in 2.5Gbit.
* Set gmac1 to gmii mode that connect to a internal gphy
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit e7774049ff ("ARM: dts: bcm283x: Define MMC interfaces at
board level") accidently dropped the bus width for the sdhci on the
RPi Zero W, because the board file was relying on the defaults
from bcm2835-rpi.dtsi. So fix this performance regression by adding
the bus width to the board file.
Fixes: e7774049ff ("ARM: dts: bcm283x: Define MMC interfaces at board level")
Reported-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
i.MX7S/D's GPT ipg clock should be from GPT clock root and
controlled by CCM's GPT CCGR, using correct clock source for
GPT ipg clock instead of IMX7D_CLK_DUMMY.
Fixes: 3ef79ca6bd ("ARM: dts: imx7d: use imx7s.dtsi as base device tree")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A previous patch disabled the SNVS power key by default which
breaks the ability for the imx6q-logicpd board to wake from sleep.
This patch re-enables this feature for this board.
Fixes: 770856f0da ("ARM: dts: imx6qdl: Enable SNVS power key according to board design")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull USB fixes from Greg KH:
"Here are a lot of small USB driver fixes for 5.4-rc3.
syzbot has stepped up its testing of the USB driver stack, now able to
trigger fun race conditions between disconnect and probe functions.
Because of that we have a lot of fixes in here from Johan and others
fixing these reported issues that have been around since almost all
time.
We also are just deleting the rio500 driver, making all of the syzbot
bugs found in it moot as it turns out no one has been using it for
years as there is a userspace version that is being used instead.
There are also a number of other small fixes in here, all resolving
reported issues or regressions.
All have been in linux-next without any reported issues"
* tag 'usb-5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (65 commits)
USB: yurex: fix NULL-derefs on disconnect
USB: iowarrior: use pr_err()
USB: iowarrior: drop redundant iowarrior mutex
USB: iowarrior: drop redundant disconnect mutex
USB: iowarrior: fix use-after-free after driver unbind
USB: iowarrior: fix use-after-free on release
USB: iowarrior: fix use-after-free on disconnect
USB: chaoskey: fix use-after-free on release
USB: adutux: fix use-after-free on release
USB: ldusb: fix NULL-derefs on driver unbind
USB: legousbtower: fix use-after-free on release
usb: cdns3: Fix for incorrect DMA mask.
usb: cdns3: fix cdns3_core_init_role()
usb: cdns3: gadget: Fix full-speed mode
USB: usb-skeleton: drop redundant in-urb check
USB: usb-skeleton: fix use-after-free after driver unbind
USB: usb-skeleton: fix NULL-deref on disconnect
usb:cdns3: Fix for CV CH9 running with g_zero driver.
usb: dwc3: Remove dev_err() on platform_get_irq() failure
usb: dwc3: Switch to platform_get_irq_byname_optional()
...
Commit 572cf7d7b0 ("ARM: dts: Improve omap l4per idling with wlcore edge
sensitive interrupt") changed wlcore interrupts to use edge interrupt based
on what's specified in the wl1835mod.pdf data sheet.
However, there are still cases where we can have lost interrupts as
described in omap_gpio_unidle(). And using a level interrupt instead of edge
interrupt helps as we avoid the check for untriggered GPIO interrupts in
omap_gpio_unidle().
And with commit e6818d29ea ("gpio: gpio-omap: configure edge detection
for level IRQs for idle wakeup") GPIOs idle just fine with level interrupts.
Let's change omap4 and 5 wlcore users back to using level interrupt
instead of edge interrupt. Let's not change the others as I've only seen
this on omap4 and 5, probably because the other SoCs don't have l4per idle
independent of the CPUs.
Fixes: 572cf7d7b0 ("ARM: dts: Improve omap l4per idling with wlcore edge sensitive interrupt")
Depends-on: e6818d29ea ("gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup")
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: Eyal Reizer <eyalr@ti.com>
Cc: Guy Mishol <guym@ti.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clkctrl code searches for the parent clockdomain based on the name
of the CM provider node. The introduction of SGX node for omap5 made
the node name for the gpu_cm to be clock-controller. There is no
clockdomain named like this, so the lookup fails. Fix by changing
the node name properly.
Fixes: 394534cb07 ("ARM: dts: Configure sgx for omap5")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
What we thought would be the module clock is actually the clock meant to be
used by the sensors, and play no role in the CSI controller. Now that the
binding has been updated to reflect that, let's update the device tree too.
Fixes: d2b9c64443 ("ARM: dts: sun7i: Add CSI0 controller")
Reported-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
The TWL4030 used on the Logit PD Torpedo SOM does not have the
keypad pins routed. This patch disables the twl_keypad driver
to remove some splat during boot:
twl4030_keypad 48070000.i2c:twl@48:keypad: missing or malformed property linux,keymap: -22
twl4030_keypad 48070000.i2c:twl@48:keypad: Failed to build keymap
twl4030_keypad: probe of 48070000.i2c:twl@48:keypad failed with error -22
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: removed error time stamps]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This reverts commits 3d109bdca9 ("ARM: dts: sunxi: Remove useless
phy-names from EHCI and OHCI"), 0a3df8bb6d ("ARM: dts: sunxi: h3/h5:
Remove useless phy-names from EHCI and OHCI") and 3c7ab90aaa ("arm64:
dts: allwinner: Remove useless phy-names from EHCI and OHCI").
It turns out that while the USB bindings were not mentionning it, the PHY
client bindings were mandating that phy-names is set when phys is. Let's
add it back.
Fixes: 3d109bdca9 ("ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI")
Fixes: 0a3df8bb6d ("ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI")
Fixes: 3c7ab90aaa ("arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-1-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes for omaps for v5.4-rc cycle
Here are fixes for omaps to deal with few regressions, and to fix
more boot time errors and warnings:
- The recent ti-sysc interconnect target module driver changes had
incorrect clock bits for both clocks and dts that cause warnings
- For omap3-gta04, gpio changes caused the LCD to break a while back,
and after discussing things the right fix is to set spi-cs-high
- Recent omapdrm changes to use generic panels caused tfp410 to be
disabled as we now must enable the generic support for it in
defconfig
- Recent omapdrm and backlight changes also finally made droid4 LCD
to work, so let's enable it in the defconfig it can be used out
of the box. This is not strictly a fix, but we still also have the
older CONFIG_MFD_TI_LMU options available so this cuts down the
confusion for trying to guess which display and which backlight
is needed
- Recent ti-sysc interconnect target module changes need the gpio
module disabled on some boards, but this now needs to happen at
the module level, not at the gpio driver level
- Recent changes to probe system timers with ti-sysc caused warnings
about mismatch in syconfig registers, so let's configure the option
for RESET_STATUS as available in the TRMs
- Recent changes to probe LCDC with ti-sysc caused warnings about
mismatch in sysconfig registers, so let's configure the missing
idlemodes for both platform data and dts as documented in TRMs
- Since we moved mach-omap2 to probe with device tree, we've been
getting voltage controller warnings. Turns out this code is no
longer needed, so let's just remove omap2_set_init_voltage() to
get rid of the pointless warnings
- Configure am4372 dispc memory bandwidth to avoid underflow errors
* tag 'omap-for-v5.4/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372: Set memory bandwidth limit for DISPC
ARM: OMAP2+: Fix warnings with broken omap2_set_init_voltage()
ARM: OMAP2+: Add missing LCDC midlemode for am335x
ARM: OMAP2+: Fix missing reset done flag for am3 and am43
ARM: dts: Fix gpio0 flags for am335x-icev2
ARM: omap2plus_defconfig: Enable more droid4 devices as loadable modules
ARM: omap2plus_defconfig: Enable DRM_TI_TFP410
DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again
ARM: dts: Fix wrong clocks for dra7 mcasp
clk: ti: dra7: Fix mcasp8 clock bits
Link: https://lore.kernel.org/r/pull-1570040410-308159@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM SoC fixes from Olof Johansson:
"A few fixes that have trickled in through the merge window:
- Video fixes for OMAP due to panel-dpi driver removal
- Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7
- Fixing arch version on ASpeed ast2500
- Two fixes for reset handling on ARM SCMI"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: aspeed: ast2500 is ARMv6K
reset: reset-scmi: add missing handle initialisation
firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset
bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
ARM: dts: am3517-evm: Fix missing video
ARM: dts: logicpd-torpedo-baseboard: Fix missing video
ARM: omap2plus_defconfig: Fix missing video
bus: ti-sysc: Fix handling of invalid clocks
bus: ti-sysc: Fix clock handling for no-idle quirks
Set memory bandwidth limit to filter out resolutions above 720p@60Hz to
avoid underflow errors due to the bandwidth needs of higher resolutions.
am43xx can not provide enough bandwidth to DISPC to correctly handle
'high' resolutions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes for omap variants
Few fixes for ti-sysc interconnect target module driver for no-idle
quirks that caused nfsroot to fail on some dra7 boards.
And let's fixes to get LCD working again for logicpd board that got
broken a while back with removal of panel-dpi driver. We need to now
use generic CONFIG_DRM_PANEL_SIMPLE instead.
* tag 'fixes-5.4-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
ARM: dts: am3517-evm: Fix missing video
ARM: dts: logicpd-torpedo-baseboard: Fix missing video
ARM: omap2plus_defconfig: Fix missing video
bus: ti-sysc: Fix handling of invalid clocks
bus: ti-sysc: Fix clock handling for no-idle quirks
Link: https://lore.kernel.org/r/pull-1568819401-72461@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
TRM "Table 13-34. SYSCONFIG Register Field Descriptions" lists both
standbymode and idlemode that should be just the sidle and midle
registers where midle is currently unconfigured for lcdc_sysc. As
the dts data has been generated based on lcdc_sysc, we now have an
empty "ti,sysc-midle" property.
And so we currently get a warning for lcdc because of a difference
with dts provided configuration compared to the legacy platform
data. This is because lcdc has SYSC_HAS_MIDLEMODE configured in
the platform data without configuring the modes.
Let's fix the issue by adding the missing midlemode to lcdc_sysc,
and configuring the "ti,sysc-midle" property based on the TRM
values.
Fixes: f711c575cf ("ARM: dts: am335x: Add l4 interconnect hierarchy and ti-sysc data")
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ti,no-idle-on-init and ti,no-reset-on-init flags need to be at
the interconnect target module level for the modules that have it
defined. Otherwise we get the following warnings:
dts flag should be at module level for ti,no-idle-on-init
dts flag should be at module level for ti,no-reset-on-init
Fixes: 87fc89ced3 ("ARM: dts: am335x: Move l4 child devices to probe them with ti-sysc")
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Reported-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit 6953c57ab1 "gpio: of: Handle SPI chipselect legacy bindings"
did introduce logic to centrally handle the legacy spi-cs-high property
in combination with cs-gpios. This assumes that the polarity
of the CS has to be inverted if spi-cs-high is missing, even
and especially if non-legacy GPIO_ACTIVE_HIGH is specified.
The DTS for the GTA04 was orginally introduced under the assumption
that there is no need for spi-cs-high if the gpio is defined with
proper polarity GPIO_ACTIVE_HIGH.
This was not a problem until gpiolib changed the interpretation of
GPIO_ACTIVE_HIGH and missing spi-cs-high.
The effect is that the missing spi-cs-high is now interpreted as CS being
low (despite GPIO_ACTIVE_HIGH) which turns off the SPI interface when the
panel is to be programmed by the panel driver.
Therefore, we have to add the redundant and legacy spi-cs-high property
to properly activate CS.
Cc: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ahclkr clkctrl clock bit 28 only exists for mcasp 1 and 2 on dra7.
This causes the following warning on beagle-x15:
ti-sysc 48468000.target-module: could not add child clock ahclkr: -19
Also the mcasp clkctrl clock bits are wrong:
For mcasp1 and 2 we have four clocks at bits 28, 24, 22 and 0:
bit 28 is ahclkr
bit 24 is ahclkx
bit 22 is auxclk
bit 0 is fck
For mcasp3 to 8 we have three clocks at bits 24, 22 and 0.
bit 24 is ahclkx
bit 22 is auxclk
bit 0 is fck
We do not have currently mapped auxclk at bit 22 for the drivers, that can
be added if needed.
Fixes: 5241ccbf28 ("ARM: dts: Add missing ranges for dra7 mcasp l3 ports")
Cc: Suman Anna <s-anna@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull ARM SoC late updates from Arnd Bergmann:
"This is some material that we picked up into our tree late or that had
complex inter-depondencies. The fact that there are these
interdependencies tends to meant that these are often actually the
most interesting new additions:
- The new Aspeed AST2600 baseboard management controller is added,
this is a Cortex-A7 based follow-up to the ARM11 based AST2500 and
had some dependencies on other device drivers.
- After many years, support for the MMP2 based OLPC XO-1.75 finally
makes it into the kernel.
- The Armada 3720 based Turris Mox open source router platform is a
late addition and it follows some preparatory work across multiple
branches.
- The OMAP2+ platform had some large-scale cleanup involving driver
changes and DT changes, here we finish it off, dropping a lot of
the now-unused platform data.
- The TI K3 platform that got added for 5.3 gains a lot more support
for individual bits on the SoC, this part just came late for the
merge window"
[ This pull request itself wasn't actually sent late at all by Arnd, but
I waited on the branches that it used to be pulled first, so it ends
up being merged much later than the other ARM SoC pull requests this
merge window - Linus ]
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
ARM: dts: dir685: Drop spi-cpol from the display
ARM: dts: aspeed: Add AST2600 pinmux nodes
ARM: dts: aspeed: Add AST2600 and EVB
ARM: exynos: Enable support for ARM architected timers
ARM: samsung: Fix system restart on S3C6410
ARM: dts: mmp2: add OLPC XO 1.75 machine
ARM: dts: mmp2: rename the USB PHY node
ARM: dts: mmp2: specify reg-shift for the UARTs
ARM: dts: mmp2: add camera interfaces
ARM: dts: mmp2: fix the SPI nodes
ARM: dts: mmp2: trivial whitespace fix
arm64: dts: marvell: add DTS for Turris Mox
dt-bindings: marvell: document Turris Mox compatible
arm64: dts: marvell: armada-37xx: add SPI CS1 pinctrl
arm64: dts: ti: k3-j721e-main: Fix gic-its node unit-address
arm64: dts: ti: k3-am65-main: Fix gic-its node unit-address
arm64: dts: ti: k3-j721e-main: Add hwspinlock node
arm64: dts: ti: k3-am65-main: Add hwspinlock node
arm64: dts: k3-j721e: Add gpio-keys on common processor board
dt-bindings: pinctrl: k3: Introduce pinmux definitions for J721E
...
Pull USB updates from Greg KH:
"Here is the big set of USB patches for 5.4-rc1.
Two major chunks of code are moving out of the tree and into the
staging directory, uwb and wusb (wireless USB support), because there
are no devices that actually use this protocol anymore, and what we
have today probably doesn't work at all given that the maintainers
left many many years ago. So move it to staging where it will be
removed in a few releases if no one screams.
Other than that, lots of little things. The usual gadget and xhci and
usb serial driver updates, along with a bunch of sysfs file cleanups
due to the driver core changes to support that. Nothing really major,
just constant forward progress.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (159 commits)
USB: usbcore: Fix slab-out-of-bounds bug during device reset
usb: cdns3: Remove redundant dev_err call in cdns3_probe()
USB: rio500: Fix lockdep violation
USB: rio500: simplify locking
usb: mtu3: register a USB Role Switch for dual role mode
usb: common: add USB GPIO based connection detection driver
usb: common: create Kconfig file
usb: roles: get usb-role-switch from parent
usb: roles: Add fwnode_usb_role_switch_get() function
device connection: Add fwnode_connection_find_match()
usb: roles: Introduce stubs for the exiting functions in role.h
dt-bindings: usb: mtu3: add properties about USB Role Switch
dt-bindings: usb: add binding for USB GPIO based connection detection driver
dt-bindings: connector: add optional properties for Type-B
dt-binding: usb: add usb-role-switch property
usbip: Implement SG support to vhci-hcd and stub driver
usb: roles: intel: Enable static DRD mode for role switch
xhci-ext-caps.c: Add property to disable Intel SW switch
usb: dwc3: remove generic PHY calibrate() calls
usb: core: phy: add support for PHY calibration
...
Pull ARM DT updates from Arnd Bergmann:
"This is another huge branch with close to 450 changessets related to
devicetree files, roughly half of this for 32-bit and 64-bit
respectively. There are lots of cleanups and additional hardware
support for platforms we already support based on SoCs from Renesas,
ST-Microelectronics, Intel/Altera, Rockchips, Allwinner, Broadcom and
other manufacturers.
A total of 6 new SoCs and 37 new boards gets added this time, one more
SoC will come in a follow-up branch. Most of the new boards are for
64-bit ARM SoCs, the others are typically for the 32-bit Cortex-A7.
Going more into details for SoC platforms with new hardware support:
- The Snapdragon 855 (SM8150) is Qualcomm's current high-end phone
platform, usually paired with an external 5G modem. So far we only
support the Qualcomm SM8150 MTP reference platform, but no actual
products.
- For the slightly older Qualcomm platforms, support for several
interesting products is getting added: Three laptops based on
Snapdragon 835/MSM8998 (Asus NovaGo, HP Envy X2 and Lenovo Miix
630), one laptop based on Snapdragon 850/sdm850 (Lenovo Yoga C630)
and several phones based on the older Snapdragon 410/MSM8916
(Samsung A3 and A5, Longcheer L8150 aka Android One 2nd gen "seed"
aka Wileyfox Swift).
- Mediatek MT7629 is a new wireless network router chip, similar to
the older MT7623. It gets added together with the reference board
implementation.
- Allwinner V3 is a repackaged version of the existing low-end V3s
chip, and is used in the tiny Lichee Pi Zero plus, also added here.
There is also a new TV set-top box based on Allwinner H6, the Tanix
TX6, and the eMMC variant of the Olimex A64-Olinuxino development
board.
- NXP i.MX8M Nano is a new member of the ever-expanding i.MX SoC
family, similar to the i.MX8M Mini. As usual, there is a large
number of new boards for i.MX SoCs: Einfochips i.MX8QXP AI_ML,
SolidRun Hummingboard Pulse baseboard and System-on-Module,
Boundary Devices i.MX8MQ Nitrogen8M, and TechNexion
PICO-PI-IMX8M-DEV for the 64-bit i.MX8 line. For 32-bit, we get the
Kontron i.MX6UL N6310 SoM with two baseboards, the PHYTEC
phyBOARD-Segin SoM with three baseboards, and the Zodiac Inflight
Innovations i.MX7 RMU2 board.
- In a different NXP product line, the Layerscape LS1046A "Freeway"
reference board gets added.
- Amlogic SM1 (S905X3) and G12B (S922X, A311D) are updated chips from
their set-top-box line and smart speaker with newer CPU and GPU
cores compared to their predecessors. Both are now also supported
by the Khadas VIM3 development board series, and the dts files for
that get reorganized a bit to better deal with all variants.
Another board based on SM1 that gets added is the SEI Robotics
SEI610.
- There are a handful of new x86 and Power9 server boards using
Aspeed BMC chips that are gaining support for running Linux on the
BMC through the OpenBMC project: Facebook
Minipack/Wedge100/Wedge40, Lenovo Hr855xg2, and Mihawk. Notably
these are still new machines using SoCs based on the ARM9 and ARM11
CPU cores, as support for the new Cortex-A7 based AST2600 is still
ramping up.
- There are three new end-user products using 32-bit Rockchips SoCs:
Mecer Xtreme Mini S6 is an Android "mini PC" box based on the
low-end RK3229 chip, while the two AOpen products Chromebox Mini
(Fievel) and Chromebase Mini (Tiger) run ChromeOS and are meant for
commercial settings(digital signage, PoS, ...).
- One more single-board computer based on the popular 64-bit RK3399
is added: the Leez RK3399 P710"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (467 commits)
arm64: dts: qcom: Add Lenovo Yoga C630
ARM: dts: aspeed-g5: Fixe gpio-ranges upper limit
ARM; dts: aspeed: mihawk: File should not be executable
ARM: dts: aspeed: swift: Change power supplies to version 2
ARM: dts: aspeed: vesnin: Add secondary SPI flash chip
ARM: dts: aspeed: vesnin: Add wdt2 with alt-boot option
ARM: dts: aspeed-g4: Add all flash chips
ARM: dts: exynos: Enable GPU/Mali T604 on Arndale board
ARM: dts: exynos: Enable GPU/Mali T604 on Chromebook Snow
ARM: dts: exynos: Add GPU/Mali T604 node to Exynos5250
ARM: dts: exynos: Fix min/max buck4 for GPU on Arndale board
ARM: dts: exynos: Mark LDO10 as always-on on Peach Pit/Pi Chromebooks
ARM: dts: exynos: Remove not accurate secondary ADC compatible
arm64: dts: rockchip: limit clock rate of MMC controllers for RK3328
arm64: dts: meson-sm1-sei610: add stdout-path property back
arm64: dts: meson-sm1-sei610: enable DVFS
arm64: dts: khadas-vim3: add support for the SM1 based VIM3L
dt-bindings: arm: amlogic: add Amlogic SM1 based Khadas VIM3L bindings
arm64: dts: khadas-vim3: move common nodes into meson-khadas-vim3.dtsi
arm64: dts: meson: g12a: add reset to tdm formatters
...
The D-Link DIR-685 had its clock polarity set as active
low using the special SPI "spi-cpol" property.
This is not correct: the datasheet clearly states:
"Fix SCL to GND level when not in use" which is
indicative that this line is active high.
After a recent fix making the GPIO-based SPI driver
force the clock line de-asserted at the beginning of
each SPI transaction this reared its ugly head: now
de-asserted was taken to mean the line should be
driven high, but it should be driven low.
Fix this up in the DTS file and the display works again.
Link: https://lore.kernel.org/r/20190915135444.11066-1-linus.walleij@linaro.org
Cc: Mark Brown <broonie@kernel.org>
Fixes: 2922d1cc16 ("spi: gpio: Add SPI_MASTER_GPIO_SS flag")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is a fairly complete description of an OLPC XO 1.75 laptop.
What's missing for now is the GPU, LCD controller, DCON, the panel and
audio.
The machine is booted with OpenFirmware and thus has a devicetree.
However, older versions are unable to create a valid FDT and don't
follow the Linux bindings. Having an device tree in the kernel tree
makes it easier to use mainline kernels on such machines, test changes
with CONFIG_ARM_APPENDED_DTB and give a good reference on what bindings
are used on the machine without an access to one.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
This device is not an OTG phy, it's a regular USB HS phy. Follow the
generic node name recommendation, and rename it to "usb-phy".
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
This makes the 8250_of driver happy. There are two more drivers in the
tree that bind to mrvl,mmp-uart compatibles: pxa and 8250_pxa and
neither of them requires the reg-shift property, assuming it's always 2.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
The SPI bus has a single address cell and not size cells.
Also, dtc thinks the SPI nodes are preferrably called "spi" and it is
right to think so.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
When the pinmux configuration was added, it was accidentally placed into
the omap3_pmx_wkup node when it should have been placed into the
omap3_pmx_core. This error was accidentally propagated to stable by
me when I blindly requested the pull after seeing I2C issues without
actually reviewing the content of the pinout. Since the bootloader
previously muxed these correctly in the past, was a hidden error.
This patch moves the i2c2_pins and i2c3_pins to the correct node
which should eliminate i2c bus errors and timeouts due to the fact
the bootloader uses the save device tree that no longer properly
assigns these pins.
Fixes: 5fe3c0fa0d ("ARM: dts: Add pinmuxing for i2c2 and i2c3
for LogicPD SOM-LV") #4.9+
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A previous commit removed the panel-dpi driver, which made the
video on the AM3517-evm stop working because it relied on the dpi
driver for setting video timings. Now that the simple-panel driver
is available in omap2plus, this patch migrates the am3517-evm
to use a similar panel and remove the manual timing requirements.
Fixes: 8bf4b16211 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A previous commit removed the panel-dpi driver, which made the
Torpedo video stop working because it relied on the dpi driver
for setting video timings. Now that the simple-panel driver is
available in omap2plus, this patch migrates the Torpedo dev kits
to use a similar panel and remove the manual timing requirements.
Fixes: 8bf4b16211 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
