Pull objtool updates from Ingo Molnar:
"There are a lot of objtool changes in this cycle, all across the map:
- Speed up objtool significantly, especially when there are large
number of sections
- Improve objtool's understanding of special instructions such as
IRET, to reduce the number of annotations required
- Implement 'noinstr' validation
- Do baby steps for non-x86 objtool use
- Simplify/fix retpoline decoding
- Add vmlinux validation
- Improve documentation
- Fix various bugs and apply smaller cleanups"
* tag 'objtool-core-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
objtool: Enable compilation of objtool for all architectures
objtool: Move struct objtool_file into arch-independent header
objtool: Exit successfully when requesting help
objtool: Add check_kcov_mode() to the uaccess safelist
samples/ftrace: Fix asm function ELF annotations
objtool: optimize add_dead_ends for split sections
objtool: use gelf_getsymshndx to handle >64k sections
objtool: Allow no-op CFI ops in alternatives
x86/retpoline: Fix retpoline unwind
x86: Change {JMP,CALL}_NOSPEC argument
x86: Simplify retpoline declaration
x86/speculation: Change FILL_RETURN_BUFFER to work with objtool
objtool: Add support for intra-function calls
objtool: Move the IRET hack into the arch decoder
objtool: Remove INSN_STACK
objtool: Make handle_insn_ops() unconditional
objtool: Rework allocating stack_ops on decode
objtool: UNWIND_HINT_RET_OFFSET should not check registers
objtool: is_fentry_call() crashes if call has no destination
x86,smap: Fix smap_{save,restore}() alternatives
...
Pull locking updates from Ingo Molnar:
"The biggest change to core locking facilities in this cycle is the
introduction of local_lock_t - this primitive comes from the -rt
project and identifies CPU-local locking dependencies normally handled
opaquely beind preempt_disable() or local_irq_save/disable() critical
sections.
The generated code on mainline kernels doesn't change as a result, but
still there are benefits: improved debugging and better documentation
of data structure accesses.
The new local_lock_t primitives are introduced and then utilized in a
couple of kernel subsystems. No change in functionality is intended.
There's also other smaller changes and cleanups"
* tag 'locking-core-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
zram: Use local lock to protect per-CPU data
zram: Allocate struct zcomp_strm as per-CPU memory
connector/cn_proc: Protect send_msg() with a local lock
squashfs: Make use of local lock in multi_cpu decompressor
mm/swap: Use local_lock for protection
radix-tree: Use local_lock for protection
locking: Introduce local_lock()
locking/lockdep: Replace zero-length array with flexible-array
locking/rtmutex: Remove unused rt_mutex_cmpxchg_relaxed()
Pull RCU updates from Ingo Molnar:
"The RCU updates for this cycle were:
- RCU-tasks update, including addition of RCU Tasks Trace for BPF use
and TASKS_RUDE_RCU
- kfree_rcu() updates.
- Remove scheduler locking restriction
- RCU CPU stall warning updates.
- Torture-test updates.
- Miscellaneous fixes and other updates"
* tag 'core-rcu-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (103 commits)
rcu: Allow for smp_call_function() running callbacks from idle
rcu: Provide rcu_irq_exit_check_preempt()
rcu: Abstract out rcu_irq_enter_check_tick() from rcu_nmi_enter()
rcu: Provide __rcu_is_watching()
rcu: Provide rcu_irq_exit_preempt()
rcu: Make RCU IRQ enter/exit functions rely on in_nmi()
rcu/tree: Mark the idle relevant functions noinstr
x86: Replace ist_enter() with nmi_enter()
x86/mce: Send #MC singal from task work
x86/entry: Get rid of ist_begin/end_non_atomic()
sched,rcu,tracing: Avoid tracing before in_nmi() is correct
sh/ftrace: Move arch_ftrace_nmi_{enter,exit} into nmi exception
lockdep: Always inline lockdep_{off,on}()
hardirq/nmi: Allow nested nmi_enter()
arm64: Prepare arch_nmi_enter() for recursion
printk: Disallow instrumenting print_nmi_enter()
printk: Prepare for nested printk_nmi_enter()
rcutorture: Convert ULONG_CMP_LT() to time_before()
torture: Add a --kasan argument
torture: Save a few lines by using config_override_param initially
...
Pull kprobes updates from Ingo Molnar:
"Various kprobes updates, mostly centered around cleaning up the
no-instrumentation logic.
Instead of the current per debug facility blacklist, use the more
generic .noinstr.text approach, combined with a 'noinstr' marker for
functions.
Also add instrumentation_begin()/end() to better manage the exact
place in entry code where instrumentation may be used.
And add a kprobes blacklist for modules"
* tag 'core-kprobes-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kprobes: Prevent probes in .noinstr.text section
vmlinux.lds.h: Create section for protection against instrumentation
samples/kprobes: Add __kprobes and NOKPROBE_SYMBOL() for handlers.
kprobes: Support NOKPROBE_SYMBOL() in modules
kprobes: Support __kprobes blacklist in modules
kprobes: Lock kprobe_mutex while showing kprobe_blacklist
Pull printk updates from Petr Mladek:
- Benjamin Herrenschmidt solved a problem with non-matched console
aliases by first checking consoles defined on the command line. It is
a more conservative approach than the previous attempts.
- Benjamin also made sure that the console accessible via /dev/console
always has CON_CONSDEV flag.
- Andy Shevchenko added the %ptT modifier for printing struct time64_t.
It extends the existing %ptR handling for struct rtc_time.
- Bruno Meneguele fixed /dev/kmsg error value returned by unsupported
SEEK_CUR.
- Tetsuo Handa removed unused pr_cont_once().
... and a few small fixes.
* tag 'printk-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk: Remove pr_cont_once()
printk: handle blank console arguments passed in.
kernel/printk: add kmsg SEEK_CUR handling
printk: Fix a typo in comment "interator"->"iterator"
usb: pulse8-cec: Switch to use %ptT
ARM: bcm2835: Switch to use %ptT
lib/vsprintf: Print time64_t in human readable format
lib/vsprintf: update comment about simple_strto<foo>() functions
printk: Correctly set CON_CONSDEV even when preferred console was not registered
printk: Fix preferred console selection with multiple matches
printk: Move console matching logic into a separate function
printk: Convert a use of sprintf to snprintf in console_unlock
Pull fsverity updates from Eric Biggers:
"Fix kerneldoc warnings and some coding style inconsistencies.
This mirrors the similar cleanups being done in fs/crypto/"
* tag 'fsverity-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
fs-verity: remove unnecessary extern keywords
fs-verity: fix all kerneldoc warnings
Pull fscrypt updates from Eric Biggers:
- Add the IV_INO_LBLK_32 encryption policy flag which modifies the
encryption to be optimized for eMMC inline encryption hardware.
- Make the test_dummy_encryption mount option for ext4 and f2fs support
v2 encryption policies.
- Fix kerneldoc warnings and some coding style inconsistencies.
* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
fscrypt: add support for IV_INO_LBLK_32 policies
fscrypt: make test_dummy_encryption use v2 by default
fscrypt: support test_dummy_encryption=v2
fscrypt: add fscrypt_add_test_dummy_key()
linux/parser.h: add include guards
fscrypt: remove unnecessary extern keywords
fscrypt: name all function parameters
fscrypt: fix all kerneldoc warnings
Pull pstore updates from Kees Cook:
"Fixes and new features for pstore.
This is a pretty big set of changes (relative to past pstore pulls),
but it has been in -next for a while. The biggest change here is the
ability to support a block device as a pstore backend, which has been
desired for a while. A lot of additional fixes and refactorings are
also included, mostly in support of the new features.
- refactor pstore locking for safer module unloading (Kees Cook)
- remove orphaned records from pstorefs when backend unloaded (Kees
Cook)
- refactor dump_oops parameter into max_reason (Pavel Tatashin)
- introduce pstore/zone for common code for contiguous storage
(WeiXiong Liao)
- introduce pstore/blk for block device backend (WeiXiong Liao)
- introduce mtd backend (WeiXiong Liao)"
* tag 'pstore-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (35 commits)
mtd: Support kmsg dumper based on pstore/blk
pstore/blk: Introduce "best_effort" mode
pstore/blk: Support non-block storage devices
pstore/blk: Provide way to query pstore configuration
pstore/zone: Provide way to skip "broken" zone for MTD devices
Documentation: Add details for pstore/blk
pstore/zone,blk: Add ftrace frontend support
pstore/zone,blk: Add console frontend support
pstore/zone,blk: Add support for pmsg frontend
pstore/blk: Introduce backend for block devices
pstore/zone: Introduce common layer to manage storage zones
ramoops: Add "max-reason" optional field to ramoops DT node
pstore/ram: Introduce max_reason and convert dump_oops
pstore/platform: Pass max_reason to kmesg dump
printk: Introduce kmsg_dump_reason_str()
printk: honor the max_reason field in kmsg_dumper
printk: Collapse shutdown types into a single dump reason
pstore/ftrace: Provide ftrace log merging routine
pstore/ram: Refactor ftrace buffer merging
pstore/ram: Refactor DT size parsing
...
Pull crypto updates from Herbert Xu:
"API:
- Introduce crypto_shash_tfm_digest() and use it wherever possible.
- Fix use-after-free and race in crypto_spawn_alg.
- Add support for parallel and batch requests to crypto_engine.
Algorithms:
- Update jitter RNG for SP800-90B compliance.
- Always use jitter RNG as seed in drbg.
Drivers:
- Add Arm CryptoCell driver cctrng.
- Add support for SEV-ES to the PSP driver in ccp"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (114 commits)
crypto: hisilicon - fix driver compatibility issue with different versions of devices
crypto: engine - do not requeue in case of fatal error
crypto: cavium/nitrox - Fix a typo in a comment
crypto: hisilicon/qm - change debugfs file name from qm_regs to regs
crypto: hisilicon/qm - add DebugFS for xQC and xQE dump
crypto: hisilicon/zip - add debugfs for Hisilicon ZIP
crypto: hisilicon/hpre - add debugfs for Hisilicon HPRE
crypto: hisilicon/sec2 - add debugfs for Hisilicon SEC
crypto: hisilicon/qm - add debugfs to the QM state machine
crypto: hisilicon/qm - add debugfs for QM
crypto: stm32/crc32 - protect from concurrent accesses
crypto: stm32/crc32 - don't sleep in runtime pm
crypto: stm32/crc32 - fix multi-instance
crypto: stm32/crc32 - fix run-time self test issue.
crypto: stm32/crc32 - fix ext4 chksum BUG_ON()
crypto: hisilicon/zip - Use temporary sqe when doing work
crypto: hisilicon - add device error report through abnormal irq
crypto: hisilicon - remove codes of directly report device errors through MSI
crypto: hisilicon - QM memory management optimization
crypto: hisilicon - unify initial value assignment into QM
...
Pull regulator updates from Mark Brown:
"The big change in this release is that Matti Vaittinen has factored
out the linear ranges support into a separate library in lib/ since it
is also useful for at least the power subsystem (and most likely
others too), it helps subsystems which need to map register values
into more useful real world values do so with minimal per-driver code.
- Factoring out of the linear ranges support into a library in lib/
from Matti Vaittinen.
- Trace points for bypass mode.
- Use the consumer name in debugfs to make it easier to understand.
- New drivers for Maxim MAX77826 and MAX8998"
* tag 'regulator-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (23 commits)
regulator: max8998: max8998_set_current_limit() can be static
dt-bindings: regulator: Convert anatop regulator to json-schema
regulator: core: Add regulator bypass trace points
regulator: extract voltage balancing code to the separate function
regulator/mfd: max8998: Document charger regulator
regulator: max8998: Add charger regulator
MAINTAINERS: Add maintainer entry for linear ranges helper
regulator: bd718x7: remove voltage change restriction from BD71847 LDOs
lib: linear_ranges: Add missing MODULE_LICENSE()
regulator: use linear_ranges helper
power: supply: bd70528: rename linear_range to avoid collision
lib/test_linear_ranges: add a test for the 'linear_ranges'
lib: add linear ranges helpers
regulator: db8500-prcmu: Use true,false for bool variable
regulator: bd718x7: remove voltage change restriction from BD71847
regulator: max77826: Remove erroneous additionalProperties
regulator: qcom-rpmh: Fix typos in pm8150 and pm8150l
regulator: Document bindings for max77826
regulator: max77826: Add max77826 regulator driver
regulator: tps80031: remove redundant assignment to variables ret and val
...
Pull regmap updates from Mark Brown:
"This has been a very active release for the regmap API for some
reason, a lot of it due to new devices with odd requirements that can
sensibly be handled here.
- Add support for buses implementing a custom reg_update_bits()
method in case the bus has a native operation for this.
- Support 16 bit register addresses in SMBus.
- Allow customization of the device attached to regmap-irq.
- Helpers for bitfield operations and per-port field initializations"
* tag 'regmap-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: provide helpers for simple bit operations
regmap: add helper for per-port regfield initialization
regmap-i2c: add 16-bit width registers support
regmap: Simplify implementation of the regmap_field_read_poll_timeout() macro
regmap: Simplify implementation of the regmap_read_poll_timeout() macro
regmap: add reg_sequence helpers
regmap-irq: make it possible to add irq_chip do a specific device node
regmap: Add bus reg_update_bits() support
regmap: debugfs: check count when read regmap file
Pull hwmon updates from Guenter Roeck:
"Infrastructure:
- Add notification support
New drivers:
- Baikal-T1 PVT sensor driver
- amd_energy driver to report energy counters
- Driver for Maxim MAX16601
- Gateworks System Controller
Various:
- applesmc: avoid overlong udelay()
- dell-smm: Use one DMI match for all XPS models
- ina2xx: Implement alert functions
- lm70: Add support for ACPI
- lm75: Fix coding-style warnings
- lm90: Add max6654 support to lm90 driver
- nct7802: Replace container_of() API
- nct7904: Set default timeout
- nct7904: Add watchdog function
- pmbus: Improve initialization of 'currpage' and 'currphase'"
* tag 'hwmon-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (24 commits)
hwmon: Add Baikal-T1 PVT sensor driver
hwmon: Add notification support
dt-bindings: hwmon: Add Baikal-T1 PVT sensor binding
hwmon: (applesmc) avoid overlong udelay()
hwmon: (nct7904) Set default timeout
hwmon: (amd_energy) Missing platform_driver_unregister() on error in amd_energy_init()
MAINTAINERS: add entry for AMD energy driver
hwmon: (amd_energy) Add documentation
hwmon: Add amd_energy driver to report energy counters
hwmon: (nct7802) Replace container_of() API
hwmon: (lm90) Add max6654 support to lm90 driver
hwmon : (nct6775) Use kobj_to_dev() API
hwmon: (pmbus) Driver for Maxim MAX16601
hwmon: (pmbus) Improve initialization of 'currpage' and 'currphase'
hwmon: (adt7411) update contact email
hwmon: (lm75) Fix all coding-style warnings on lm75 driver
hwmon: Reduce indentation level in __hwmon_device_register()
hwmon: (ina2xx) Implement alert functions
hwmon: (lm70) Add support for ACPI
hwmon: (dell-smm) Use one DMI match for all XPS models
...
Pull tpm updates from Jarkko Sakkinen.
* tag 'tpmdd-next-20200522' of git://git.infradead.org/users/jjs/linux-tpmdd:
tpm: eventlog: Replace zero-length array with flexible-array member
tpm/tpm_ftpm_tee: Use UUID API for exporting the UUID
Pull networking fixes from David Miller:
"Another week, another set of bug fixes:
1) Fix pskb_pull length in __xfrm_transport_prep(), from Xin Long.
2) Fix double xfrm_state put in esp{4,6}_gro_receive(), also from Xin
Long.
3) Re-arm discovery timer properly in mac80211 mesh code, from Linus
Lüssing.
4) Prevent buffer overflows in nf_conntrack_pptp debug code, from
Pablo Neira Ayuso.
5) Fix race in ktls code between tls_sw_recvmsg() and
tls_decrypt_done(), from Vinay Kumar Yadav.
6) Fix crashes on TCP fallback in MPTCP code, from Paolo Abeni.
7) More validation is necessary of untrusted GSO packets coming from
virtualization devices, from Willem de Bruijn.
8) Fix endianness of bnxt_en firmware message length accesses, from
Edwin Peer.
9) Fix infinite loop in sch_fq_pie, from Davide Caratti.
10) Fix lockdep splat in DSA by setting lockless TX in netdev features
for slave ports, from Vladimir Oltean.
11) Fix suspend/resume crashes in mlx5, from Mark Bloch.
12) Fix use after free in bpf fmod_ret, from Alexei Starovoitov.
13) ARP retransmit timer guard uses wrong offset, from Hongbin Liu.
14) Fix leak in inetdev_init(), from Yang Yingliang.
15) Don't try to use inet hash and unhash in l2tp code, results in
crashes. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (77 commits)
l2tp: add sk_family checks to l2tp_validate_socket
l2tp: do not use inet_hash()/inet_unhash()
net: qrtr: Allocate workqueue before kernel_bind
mptcp: remove msk from the token container at destruction time.
mptcp: fix race between MP_JOIN and close
mptcp: fix unblocking connect()
net/sched: act_ct: add nat mangle action only for NAT-conntrack
devinet: fix memleak in inetdev_init()
virtio_vsock: Fix race condition in virtio_transport_recv_pkt
drivers/net/ibmvnic: Update VNIC protocol version reporting
NFC: st21nfca: add missed kfree_skb() in an error path
neigh: fix ARP retransmit timer guard
bpf, selftests: Add a verifier test for assigning 32bit reg states to 64bit ones
bpf, selftests: Verifier bounds tests need to be updated
bpf: Fix a verifier issue when assigning 32bit reg states to 64bit ones
bpf: Fix use-after-free in fmod_ret check
net/mlx5e: replace EINVAL in mlx5e_flower_parse_meta()
net/mlx5e: Fix MLX5_TC_CT dependencies
net/mlx5e: Properly set default values when disabling adaptive moderation
net/mlx5e: Fix arch depending casting issue in FEC
...
pstore/blk is similar to pstore/ram, but uses a block device as the
storage rather than persistent ram.
The pstore/blk backend solves two common use-cases that used to preclude
using pstore/ram:
- not all devices have a battery that could be used to persist
regular RAM across power failures.
- most embedded intelligent equipment have no persistent ram, which
increases costs, instead preferring cheaper solutions, like block
devices.
pstore/blk provides separate configurations for the end user and for the
block drivers. User configuration determines how pstore/blk operates, such
as record sizes, max kmsg dump reasons, etc. These can be set by Kconfig
and/or module parameters, but module parameter have priority over Kconfig.
Driver configuration covers all the details about the target block device,
such as total size of the device and how to perform read/write operations.
These are provided by block drivers, calling pstore_register_blkdev(),
including an optional panic_write callback used to bypass regular IO
APIs in an effort to avoid potentially destabilized kernel code during
a panic.
Signed-off-by: WeiXiong Liao <liaoweixiong@allwinnertech.com>
Link: https://lore.kernel.org/lkml/20200511233229.27745-3-keescook@chromium.org/
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Now that pstore_register() can correctly pass max_reason to the kmesg
dump facility, introduce a new "max_reason" module parameter and
"max-reason" Device Tree field.
The "dump_oops" module parameter and "dump-oops" Device
Tree field are now considered deprecated, but are now automatically
converted to their corresponding max_reason values when present, though
the new max_reason setting has precedence.
For struct ramoops_platform_data, the "dump_oops" member is entirely
replaced by a new "max_reason" member, with the only existing user
updated in place.
Additionally remove the "reason" filter logic from ramoops_pstore_write(),
as that is not specifically needed anymore, though technically
this is a change in behavior for any ramoops users also setting the
printk.always_kmsg_dump boot param, which will cause ramoops to behave as
if max_reason was set to KMSG_DUMP_MAX.
Co-developed-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Link: https://lore.kernel.org/lkml/20200515184434.8470-6-keescook@chromium.org/
Signed-off-by: Kees Cook <keescook@chromium.org>
Add a new member to struct pstore_info for passing information about
kmesg dump maximum reason. This allows a finer control of what kmesg
dumps are sent to pstore storage backends.
Those backends that do not explicitly set this field (keeping it equal to
0), get the default behavior: store only Oopses and Panics, or everything
if the printk.always_kmsg_dump boot param is set.
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Link: https://lore.kernel.org/lkml/20200515184434.8470-5-keescook@chromium.org/
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
kmsg_dump() allows to dump kmesg buffer for various system events: oops,
panic, reboot, etc. It provides an interface to register a callback
call for clients, and in that callback interface there is a field
"max_reason", but it was getting ignored when set to any "reason"
higher than KMSG_DUMP_OOPS unless "always_kmsg_dump" was passed as
kernel parameter.
Allow clients to actually control their "max_reason", and keep the
current behavior when "max_reason" is not set.
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Link: https://lore.kernel.org/lkml/20200515184434.8470-3-keescook@chromium.org/
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
In order to more cleanly pass around backend names, make the "name" member
const. This means the module param needs to be dynamic (technically, it
was before, so this actually cleans up a minor memory leak if a backend
was specified and then gets unloaded.)
Link: https://lore.kernel.org/lkml/20200510202436.63222-3-keescook@chromium.org/
Signed-off-by: Kees Cook <keescook@chromium.org>
Hi!
This patchset is another attempt to fix the regulator coupling on
Exynos5800/5422 SoCs. Here are links to the previous attempts:
https://lore.kernel.org/linux-samsung-soc/20191008101709.qVNy8eijBi0LynOteWFMnTg4GUwKG599n6OyYoX1Abs@z/https://lore.kernel.org/lkml/20191017102758.8104-1-m.szyprowski@samsung.com/https://lore.kernel.org/linux-pm/cover.1589528491.git.viresh.kumar@linaro.org/https://lore.kernel.org/linux-pm/20200528131130.17984-1-m.szyprowski@samsung.com/
The problem is with "vdd_int" regulator coupled with "vdd_arm" on Odroid
XU3/XU4 boards family. "vdd_arm" is handled by CPUfreq. "vdd_int" is
handled by devfreq. CPUfreq initialized quite early during boot and it
starts changing OPPs and "vdd_arm" value. Sometimes CPU activity during
boot goes down and some low-frequency OPPs are selected, what in turn
causes lowering "vdd_arm". This happens before devfreq applies its
requirements on "vdd_int". Regulator balancing code reduces "vdd_arm"
voltage value, what in turn causes lowering "vdd_int" value to the lowest
possible value. This is much below the operation point of the wcore bus,
which still runs at the highest frequency.
The issue was hard to notice because in the most cases the board managed
to boot properly, even when the regulator was set to lowest value allowed
by the regulator constraints. However, it caused some random issues,
which can be observed as "Unhandled prefetch abort" or low USB stability.
Adding more and more special cases to the generic code has been rejected,
so the only way to ensure the desired behavior on Exynos5800-based SoCs
is to make a custom regulator coupler driver.
Best regards,
Marek Szyprowski
Patch summary:
Marek Szyprowski (2):
regulator: extract voltage balancing code to separate function
soc: samsung: Add simple voltage coupler for Exynos5800
arch/arm/mach-exynos/Kconfig | 1 +
drivers/regulator/core.c | 49 ++++++++-------
drivers/soc/samsung/Kconfig | 3 +
drivers/soc/samsung/Makefile | 1 +
.../soc/samsung/exynos-regulator-coupler.c | 59 +++++++++++++++++++
include/linux/regulator/coupler.h | 8 +++
6 files changed, 101 insertions(+), 20 deletions(-)
create mode 100644 drivers/soc/samsung/exynos-regulator-coupler.c
--
2.17.1
base-commit: 8f3d9f3542
Bartosz Golaszewski <bgolaszewski@baylibre.com>:
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
I noticed that oftentimes I use regmap_update_bits() for simple bit
setting or clearing. In this case the fourth argument is superfluous as
it's always 0 or equal to the mask argument.
This series proposes to add simple bit operations for setting, clearing
and testing specific bits with regmap.
The second patch uses all three in a driver that got recently picked into
the net-next tree.
The patches obviously target different trees so - if you're ok with
the change itself - I propose you pick the first one into your regmap
tree for v5.8 and then I'll resend the second patch to add the first
user for these macros for v5.9.
v1 -> v2:
- convert the new macros to static inline functions
v2 -> v3:
- drop unneeded ternary operator
Bartosz Golaszewski (2):
regmap: provide helpers for simple bit operations
net: ethernet: mtk-star-emac: use regmap bitops
drivers/base/regmap/regmap.c | 22 +++++
drivers/net/ethernet/mediatek/mtk_star_emac.c | 80 ++++++++-----------
include/linux/regmap.h | 36 +++++++++
3 files changed, 93 insertions(+), 45 deletions(-)
base-commit: 8f3d9f3542
--
2.26.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Looking at the Felix and Ocelot drivers, Maxim asked if it would be
possible to use them as a base for a new driver for the switch inside
NXP T1040. Turns out, it is! The result is a driver eerily similar to
Felix.
The biggest challenge seems to be getting register read/write API
generic enough to cover such wild bitfield variations between hardware
generations. There is a patch on the regmap core which I would like to
get in through the networking subsystem, if possible (and if Mark is
ok), since it's a trivial addition.
Maxim Kochetkov (4):
soc/mscc: ocelot: add MII registers description
net: mscc: ocelot: convert SYS_PAUSE_CFG register access to regfield
net: mscc: ocelot: extend watermark encoding function
net: dsa: ocelot: introduce driver for Seville VSC9953 switch
Vladimir Oltean (7):
regmap: add helper for per-port regfield initialization
net: mscc: ocelot: unexport ocelot_probe_port
net: mscc: ocelot: convert port registers to regmap
net: mscc: ocelot: convert QSYS_SWITCH_PORT_MODE and SYS_PORT_MODE to
regfields
net: dsa: ocelot: create a template for the DSA tags on xmit
net: mscc: ocelot: split writes to pause frame enable bit and to
thresholds
net: mscc: ocelot: disable flow control on NPI interface
drivers/net/dsa/ocelot/Kconfig | 12 +
drivers/net/dsa/ocelot/Makefile | 6 +
drivers/net/dsa/ocelot/felix.c | 49 +-
drivers/net/dsa/ocelot/felix_vsc9959.c | 72 +-
drivers/net/dsa/ocelot/seville.c | 742 +++++++++++++++
drivers/net/dsa/ocelot/seville.h | 50 +
drivers/net/dsa/ocelot/seville_vsc9953.c | 1064 ++++++++++++++++++++++
drivers/net/ethernet/mscc/ocelot.c | 87 +-
drivers/net/ethernet/mscc/ocelot.h | 9 +-
drivers/net/ethernet/mscc/ocelot_board.c | 21 +-
drivers/net/ethernet/mscc/ocelot_io.c | 18 +-
drivers/net/ethernet/mscc/ocelot_regs.c | 57 ++
include/linux/regmap.h | 8 +
include/soc/mscc/ocelot.h | 68 +-
include/soc/mscc/ocelot_dev.h | 78 --
include/soc/mscc/ocelot_qsys.h | 13 -
include/soc/mscc/ocelot_sys.h | 23 -
net/dsa/tag_ocelot.c | 21 +-
18 files changed, 2196 insertions(+), 202 deletions(-)
create mode 100644 drivers/net/dsa/ocelot/seville.c
create mode 100644 drivers/net/dsa/ocelot/seville.h
create mode 100644 drivers/net/dsa/ocelot/seville_vsc9953.c
base-commit: 8f3d9f3542
--
2.25.1
In many instances regmap_update_bits() is used for simple bit setting
and clearing. In these cases the last argument is redundant and we can
hide it with a static inline function.
This adds three new helpers for simple bit operations: set_bits,
clear_bits and test_bits (the last one defined as a regular function).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200528154503.26304-2-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Recent change in virtio_net_hdr_to_skb() broke some packetdrill tests.
When --mss=XXX option is set, packetdrill always provide gso_type & gso_size
for its inbound packets, regardless of packet size.
if (packet->tcp && packet->mss) {
if (packet->ipv4)
gso.gso_type = VIRTIO_NET_HDR_GSO_TCPV4;
else
gso.gso_type = VIRTIO_NET_HDR_GSO_TCPV6;
gso.gso_size = packet->mss;
}
Since many other programs could do the same, relax virtio_net_hdr_to_skb()
to no longer return an error, but instead ignore gso settings.
This keeps Willem intent to make sure no malicious packet could
reach gso stack.
Note that TCP stack has a special logic in tcp_set_skb_tso_segs()
to clear gso_size for small packets.
Fixes: 6dd912f826 ("net: check untrusted gso_size at kernel entry")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace superfluous VM_BUG_ON() with comment about correct usage.
Technically reverts commit 1d148e218a ("mm: add VM_BUG_ON_PAGE() to
page_mapcount()"), but context lines have changed.
Function isolate_migratepages_block() runs some checks out of lru_lock
when choose pages for migration. After checking PageLRU() it checks
extra page references by comparing page_count() and page_mapcount().
Between these two checks page could be removed from lru, freed and taken
by slab.
As a result this race triggers VM_BUG_ON(PageSlab()) in page_mapcount().
Race window is tiny. For certain workload this happens around once a
year.
page:ffffea0105ca9380 count:1 mapcount:0 mapping:ffff88ff7712c180 index:0x0 compound_mapcount: 0
flags: 0x500000000008100(slab|head)
raw: 0500000000008100 dead000000000100 dead000000000200 ffff88ff7712c180
raw: 0000000000000000 0000000080200020 00000001ffffffff 0000000000000000
page dumped because: VM_BUG_ON_PAGE(PageSlab(page))
------------[ cut here ]------------
kernel BUG at ./include/linux/mm.h:628!
invalid opcode: 0000 [#1] SMP NOPTI
CPU: 77 PID: 504 Comm: kcompactd1 Tainted: G W 4.19.109-27 #1
Hardware name: Yandex T175-N41-Y3N/MY81-EX0-Y3N, BIOS R05 06/20/2019
RIP: 0010:isolate_migratepages_block+0x986/0x9b0
The code in isolate_migratepages_block() was added in commit
119d6d59dc ("mm, compaction: avoid isolating pinned pages") before
adding VM_BUG_ON into page_mapcount().
This race has been predicted in 2015 by Vlastimil Babka (see link
below).
[akpm@linux-foundation.org: comment tweaks, per Hugh]
Fixes: 1d148e218a ("mm: add VM_BUG_ON_PAGE() to page_mapcount()")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/159032779896.957378.7852761411265662220.stgit@buzz
Link: https://lore.kernel.org/lkml/557710E1.6060103@suse.cz/
Link: https://lore.kernel.org/linux-mm/158937872515.474360.5066096871639561424.stgit@buzz/T/ (v1)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For hwmon drivers using the hwmon_device_register_with_info() API, it
is desirable to have a generic notification mechanism available. This
mechanism can be used to notify userspace as well as the thermal
subsystem if the driver experiences any events, such as warning or
critical alarms.
Implement hwmon_notify_event() to provide this mechanism. The function
generates a sysfs event and a udev event. If the device is registered
with the thermal subsystem and the event is associated with a temperature
sensor, also notify the thermal subsystem that a thermal event occurred.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Maxim Kaurkin <Maxim.Kaurkin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The various struct pagevec per CPU variables are protected by disabling
either preemption or interrupts across the critical sections. Inside
these sections spinlocks have to be acquired.
These spinlocks are regular spinlock_t types which are converted to
"sleeping" spinlocks on PREEMPT_RT enabled kernels. Obviously sleeping
locks cannot be acquired in preemption or interrupt disabled sections.
local locks provide a trivial way to substitute preempt and interrupt
disable instances. On a non PREEMPT_RT enabled kernel local_lock() maps
to preempt_disable() and local_lock_irq() to local_irq_disable().
Create lru_rotate_pvecs containing the pagevec and the locallock.
Create lru_pvecs containing the remaining pagevecs and the locallock.
Add lru_add_drain_cpu_zone() which is used from compact_zone() to avoid
exporting the pvec structure.
Change the relevant call sites to acquire these locks instead of using
preempt_disable() / get_cpu() / get_cpu_var() and local_irq_disable() /
local_irq_save().
There is neither a functional change nor a change in the generated
binary code for non PREEMPT_RT enabled non-debug kernels.
When lockdep is enabled local locks have lockdep maps embedded. These
allow lockdep to validate the protections, i.e. inappropriate usage of a
preemption only protected sections would result in a lockdep warning
while the same problem would not be noticed with a plain
preempt_disable() based protection.
local locks also improve readability as they provide a named scope for
the protections while preempt/interrupt disable are opaque scopeless.
Finally local locks allow PREEMPT_RT to substitute them with real
locking primitives to ensure the correctness of operation in a fully
preemptible kernel.
[ bigeasy: Adopted to use local_lock ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20200527201119.1692513-4-bigeasy@linutronix.de
The radix-tree and idr preload mechanisms use preempt_disable() to protect
the complete operation between xxx_preload() and xxx_preload_end().
As the code inside the preempt disabled section acquires regular spinlocks,
which are converted to 'sleeping' spinlocks on a PREEMPT_RT kernel and
eventually calls into a memory allocator, this conflicts with the RT
semantics.
Convert it to a local_lock which allows RT kernels to substitute them with
a real per CPU lock. On non RT kernels this maps to preempt_disable() as
before, but provides also lockdep coverage of the critical region.
No functional change.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20200527201119.1692513-3-bigeasy@linutronix.de
preempt_disable() and local_irq_disable/save() are in principle per CPU big
kernel locks. This has several downsides:
- The protection scope is unknown
- Violation of protection rules is hard to detect by instrumentation
- For PREEMPT_RT such sections, unless in low level critical code, can
violate the preemptability constraints.
To address this PREEMPT_RT introduced the concept of local_locks which are
strictly per CPU.
The lock operations map to preempt_disable(), local_irq_disable/save() and
the enabling counterparts on non RT enabled kernels.
If lockdep is enabled local locks gain a lock map which tracks the usage
context. This will catch cases where an area is protected by
preempt_disable() but the access also happens from interrupt context. local
locks have identified quite a few such issues over the years, the most
recent example is:
b7d5dc2107 ("random: add a spinlock_t to struct batched_entropy")
Aside of the lockdep coverage this also improves code readability as it
precisely annotates the protection scope.
PREEMPT_RT substitutes these local locks with 'sleeping' spinlocks to
protect such sections while maintaining preemtability and CPU locality.
local locks can replace:
- preempt_enable()/disable() pairs
- local_irq_disable/enable() pairs
- local_irq_save/restore() pairs
They are also used to replace code which implicitly disables preemption
like:
- get_cpu()/put_cpu()
- get_cpu_var()/put_cpu_var()
with PREEMPT_RT friendly constructs.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20200527201119.1692513-2-bigeasy@linutronix.de
Pull fanotify FAN_DIR_MODIFY disabling from Jan Kara:
"A single patch that disables FAN_DIR_MODIFY support that was merged in
this merge window.
When discussing further functionality we realized it may be more
logical to guard it with a feature flag or to call things slightly
differently (or maybe not) so let's not set the API in stone for now."
* tag 'fsnotify_for_v5.7-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fanotify: turn off support for FAN_DIR_MODIFY
Pull cgroup fixes from Tejun Heo:
- Reverted stricter synchronization for cgroup recursive stats which
was prepping it for event counter usage which never got merged. The
change was causing performation regressions in some cases.
- Restore bpf-based device-cgroup operation even when cgroup1 device
cgroup is disabled.
- An out-param init fix.
* 'for-5.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
device_cgroup: Cleanup cgroup eBPF device filter code
xattr: fix uninitialized out-param
Revert "cgroup: Add memory barriers to plug cgroup_rstat_updated() race window"
FAN_DIR_MODIFY has been enabled by commit 44d705b037 ("fanotify:
report name info for FAN_DIR_MODIFY event") in 5.7-rc1. Now we are
planning further extensions to the fanotify API and during that we
realized that FAN_DIR_MODIFY may behave slightly differently to be more
consistent with extensions we plan. So until we finalize these
extensions, let's not bind our hands with exposing FAN_DIR_MODIFY to
userland.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
>> include/linux/netfilter/nf_conntrack_pptp.h:13:20: warning: 'const' type qualifier on return type has no effect [-Wignored-qualifiers]
extern const char *const pptp_msg_name(u_int16_t msg);
^~~~~~
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 4c559f15ef ("netfilter: nf_conntrack_pptp: prevent buffer overflows in debug code")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Syzkaller again found a path to a kernel crash through bad gso input:
a packet with gso size exceeding len.
These packets are dropped in tcp_gso_segment and udp[46]_ufo_fragment.
But they may affect gso size calculations earlier in the path.
Now that we have thlen as of commit 9274124f02 ("net: stricter
validation of untrusted gso packets"), check gso_size at entry too.
Fixes: bfd5f4a3d6 ("packet: Add GSO/csum offload support.")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
