A wrong decoding of the touch coordinate message causes a wrong touch
ID. Touch ID for dual touch must be 0 or 1.
According to the actual Neonode nine byte touch coordinate coding,
the state is transported in the lower nibble and the touch ID in
the higher nibble of payload byte five.
Signed-off-by: Knut Wohlrab <Knut.Wohlrab@de.bosch.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit c6f39257c9 ("mfd: twl6040: Use regmap for register cache")
did remove the private cache for the vibra control registers and replaced
access within twl6040_get_vibralr_status() by calls to regmap. This is OK,
as long as twl6040_get_vibralr_status() uses already cached values or is
not called from interrupt context. But we call this in vibra_play() for
checking that the vibrator is not configured for audio mode.
The result is a "BUG: scheduling while atomic" if the first use of the
twl6040 is a vibra effect, because the first fetch is by reading the
twl6040 registers through (blocking) i2c and not from the cache.
As soon as the regmap has cached the status, further calls are fine.
The solution is to move the condition to the work() function which
runs in context that can block.
The original code returns -EBUSY, but the return value of ->play()
functions is ignored anyways. Hence, we do not loose functionality
by not returning an error but just reporting the issue to INFO loglevel.
Tested-on: Pyra (omap5) prototype
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For devm-managed input devices we should not modify input device's parent,
otherwise automatic release of resources will not work properly.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For devm-managed input devices we should not modify input device's parent,
otherwise automatic release of resources will not work properly.
Tested-by: "H. Nikolaus Schaller" <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Returning ret is wrong. And checking for an error as well. User space
may call multiple times until the work is really scheduled.
twl4030-vibra.c also ignores the return value.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit 21fb9f0d5e ("Input: twl6040-vibra - use system workqueue")
says that it switches to use the system workqueue but it did neither
- remove the workqueue struct variable
- replace code to really use the system workqueue
Instead it calls queue_work() on uninitialized info->workqueue.
The result is a NULL pointer dereference in vibra_play().
Solution: use schedule_work
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The trigger delay algorithm that converts from microseconds to
the register value looks incorrect. According to most of the PMIC
documentation, the equation is
delay (Seconds) = (1 / 1024) * 2 ^ (x + 4)
except for one case where the documentation looks to have a
formatting issue and the equation looks like
delay (Seconds) = (1 / 1024) * 2 x + 4
Most likely this driver was written with the improper
documentation to begin with. According to the downstream sources
the valid delays are from 2 seconds to 1/64 second, and the
latter equation just doesn't make sense for that. Let's fix the
algorithm and the range check to match the documentation and the
downstream sources.
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 92d57a73e4 ("input: Add support for Qualcomm PMIC8XXX power key")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We shouldn't assign the parent device of the input_dev to be the
parent MFD device, because this will be used for devres which causes
input_unregister_device to run after the haptics device has been
removed, since it is itself a child of the MFD device. The default
of using the haptics device itself as the parent is correct.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds the VID/PID combination for the Xbox One version of the Mad
Catz FightStick TE 2.
The functionality that this provides is about on par with what the
Windows drivers for the stick manage to deliver.
What works:
- Digital stick
- 6 main buttons
- Xbox button
- The two buttons on the back
- The locking buttons (preventing accidental Xbox button press)
What doesn't work:
- Two of the main buttons (don't work on Windows either)
- The "Haptic" button setting does not have an effect (not sure if it
works on Windows)
I added the MAP_TRIGGERS_TO_BUTTONS option but in my (limited) testing
there was no practical difference with or without. The FightStick does
not have triggers though so adding it makes sense.
Signed-off-by: Silvan Jegen <s.jegen@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The gtco driver expects at least one valid endpoint. If given malicious
descriptors that specify 0 for the number of endpoints, it will crash in
the probe function. Ensure there is at least one endpoint on the interface
before using it.
Also let's fix a minor coding style issue.
The full correct report of this issue can be found in the public
Red Hat Bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=1283385
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
During the initialisation the driver uses a buffer on the stack for DMA.
That violates the cache coherency rules. The fix is to allocate the buffer
with kmalloc().
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ati_remote2 driver expects at least two interfaces with one
endpoint each. If given malicious descriptor that specify one
interface or no endpoints, it will crash in the probe function.
Ensure there is at least two interfaces and one endpoint for each
interface before using it.
The full disclosure: http://seclists.org/bugtraq/2016/Mar/90
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Originally the irq_mask member of rmi_function was a pointer. Then it was
switched to being a zero length array. However, the checks for a NULL
pointer where not removed.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Windows driver's settings dialog contains a visualization of the
regions for the hardware edge scrolling capability, which uses a
temporarily-enabled limited-resolution absolute mode.
This patch enables this during normal operation, and combines the
absolute packets with the existing relative packets to provide
accurate absolute position and touch reporting.
It also adds documentation for all known gesture packets and
initialization commands.
Reviewed-by: Chris Diamand <chris@diamand.org>
Signed-off-by: Richard Pospesel <pospeselr@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The powermate driver expects at least one valid USB endpoint in its
probe function. If given malicious descriptors that specify 0 for
the number of endpoints, it will crash. Validate the number of
endpoints on the interface before using them.
The full report for this issue can be found here:
http://seclists.org/bugtraq/2016/Mar/85
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On error syscon_regmap_lookup_by_phandle() returns ERR_PTR() value,
which makes a check for NULL invalid and may lead to oops on error
path.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Synaptics uses the Register Mapped Interface (RMI) protocol as a
communications interface for their devices. This driver adds the core
functionality needed to interface with RMI4 devices.
RMI devices can be connected to the host via several transport protocols
and can supports a wide variety of functionality defined by RMI functions.
Support for transport protocols and RMI functions are implemented in
individual drivers. The RMI4 core driver uses a bus architecture to
facilitate the various combinations of transport and function drivers
needed by a particular device.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Christopher Heiny <cheiny@synaptics.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add device tree support for the I2C and SPI variant of AD7879(-1).
This allows to specify the touchscreen controller as a I2C client
node or SPI slave device. Most of the options available in platform
data are also available as device tree properties, the only exception
being GPIO capabilities, which can not be activated through device
tree currently.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The X/Y position measurements read from the controller are interpreted
wrong. The first measurement X+ contains the Y position, and the second
measurement Y+ the X position (see also Table 11 Register Table in the
data sheet).
The problem is already known and a swap option has been introduced:
commit 6680884a44 ("Input: ad7879 - add option to correct xy axis")
However, the meaning of the new boolean is inverted since the underlying
values are already swapped. Let ts->swap_xy set to true actually be the
swapped configuration of the two axis.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The header file is used by the SPI and I2C variant of the driver.
Therefore, move it to a more generic place under platform_data.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Technologic Systems TS-4800 is an i.MX515 board, so its drivers
are useless unless building a SOC_IMX51 kernel, except for build
testing purposes.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Bring in updates to roraty encoder driver switching it away from legacy
platform data and over to generic device properties and adding support
for encoders using more than 2 GPIOs.
When changing the scan rate as part of runtime-resume process we may lose
some of the events, because:
1) for gen3 trackpads, the driver must msleep() some time to ensure that
the device is ready to accept next command;
2) for gen5 and later trackpads, the queue dumping function will simply
ignore the events when waiting for the set power mode command response.
The solution is to keep polling and report those valid events when the set
power mode command is in progress.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A dependency on ARCH_SHMOBILE seems to be the best option for sh_keysc:
* For Super H based SoCs: sh_keysc is used on SH_MIGOR, SH_ECOVEC, SH_KFR2R09,
SH_7722_SOLUTION_ENGINE, and SH_7724_SOLUTION_ENGINE, which depend on
either CPU_SUBTYPE_SH7722 or CPU_SUBTYPE_SH7724, and both select
ARCH_SHMOBILE.
* For ARM Based SoCs: Since the removal of legacy (non-multiplatform) support
this driver has not been used by any Renesas ARM based SoCs. The Renesas
ARM based SoCs currently select ARCH_SHMOBILE, however, it is planned
that this will no longer be the case.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for retrieving device resolution (pixels per mm) from firmware
and using it when setting up input device.
Signed-off-by: Sangwon Jee <jeesw@melfas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This changes how the used gpios are stored (i.e. a struct gpio_descs
instead of two struct gpio_desc) and as with >2 gpios the states are
numbered differently the function rotary_encoder_get_state returns
unencoded numbers instead of grey encoded numbers before. The latter has
some implications on how the returned value is used and so the change is
bigger than one might expect at first.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Drop support for platform data passed via a C-structure and switch to
device properties instead, which should make the driver compatible with all
platforms: OF, ACPI and static boards. Static boards should use property
sets to communicate device parameters to the driver.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit e4b88e1989
"Input: stmpe-ts - enforce device tree only mode"
removed platform data but accidentally stripped away useful
kerneldoc, so reintroduce it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The SNVS power key driver has suspend/resume functions that
are accessed using SIMPLE_DEV_PM_OPS, which hide the reference
when CONFIG_PM_SLEEP is not set, resulting in a warning about
unused functions:
drivers/input/keyboard/snvs_pwrkey.c:183:12: error: 'imx_snvs_pwrkey_suspend' defined but not used [-Werror=unused-function]
drivers/input/keyboard/snvs_pwrkey.c:194:12: error: 'imx_snvs_pwrkey_resume' defined but not used [-Werror=unused-function]
This adds __maybe_unused annotations to let the compiler know
it can silently drop the function definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The spear keyboard driver uses #ifdef CONFIG_PM to hide its
power management functions, but then uses references from
SIMPLE_DEV_PM_OPS that are only present if both CONFIG_PM
and CONFIG_PM_SLEEP are set, resulting in a warning about unused
functions:
drivers/input/keyboard/spear-keyboard.c:292:12: error: 'spear_kbd_suspend' defined but not used [-Werror=unused-function]
drivers/input/keyboard/spear-keyboard.c:345:12: error: 'spear_kbd_resume' defined but not used [-Werror=unused-function]
This removes the #ifdef and instead uses a __maybe_unused
annotation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of manipulating capability bits directly let's use appropriate
helpers. Also there is no need to explicitly set EV_ABS when calling
input_set_abs_params().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of using old GPIO API, let's switch to GPIOD API, which
automatically handles polarity.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of guarding PM methods with #ifdef let's mark them as
__maybe_unused as it allows for better compile coverage.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert to use threaded IRQs to support GPIOs that can sleep.
Protect the irq handler with mutex as it can be triggered from
two different irq lines accessing the same state.
This allows using GPIO expanders behind I2C or SPI bus.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
