This patch adds helpers for calculating the maximum compressed BPP
supported with small joiner.
This also adds a helper for calculating the slice count in case
of small joiner.
These are inside intel_dp since they take into account hardware
limitations.
v6:
* Take mode_clock and mode_hdisplay as input arguments
so that this can be called in intel_dp_mode_valid (Manasi)
v5:
* Get the max slice width from DPCD
* Check against Min_Slice_width of 2560 (Anusha)
v4:
* #defines for PPR in slice count helper (Gaurav)
v3:
* Simply logic for bpp (DK)
* Limit the valid slice count by max supported by Sink (Manasi)
v2:
* Change the small joiner RAM buffer constant as bspec changed (Manasi)
* rename it as SMALL_JOINER since we are not enabling
big joiner yet (Anusha)
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-5-manasi.d.navare@intel.com
DSC is supported on eDP starting GEN 10 display (on GLK) and on DP starting
GEN 11.
This patch implements the discovery phase of DSC. On hotplug,
source reads the DSC DPCD register set (0x00060 - 0x0006F) to
read the decompression capabilities of the sink device.
This entire block of registers is cached in intel_dp so that
capability information can be used during DSC configuration
phase during compute_config phase of the modeset.
For eDP, this caching happens during the eDP initialization.
This caching is done only for eDP and DP rev >= 1.4
v5:
* Fix the block comment (Gaurav)
* Fix the commit message DSC DPCD addresses (Gaurav)
* Use DRM_ERROR for dpcd_read fail (Gaurav,Anusha)
v4:
* Cache these only for Gen >= 11
v3:
* Remove the dsc_sink_support field in intel_dp (Jani N)
v2:
* Clear the cached registers on hotplug always (Jani N)
* Combine the eDP and DP caching in same function (Jani N)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-3-manasi.d.navare@intel.com
LSPCON chips can generate YCBCR outputs, if asked nicely :).
In order to generate YCBCR 4:2:0 outputs, a source must:
- send YCBCR 4:4:4 signals to LSPCON
- program color space as 4:2:0 in AVI infoframes
Whereas for YCBCR 4:4:4 outputs, the source must:
- send YCBCR 4:4:4 signals to LSPCON
- program color space as 4:4:4 in AVI infoframes
So for both 4:2:0 as well as 4:4:4 outputs, we are driving the
pipe for YCBCR 4:4:4 output, but AVI infoframe's color space
information indicates LSPCON FW to start scaling down from YCBCR
4:4:4 and generate YCBCR 4:2:0 output. As the scaling is done by
LSPCON device, we need not to reserve a scaler for 4:2:0 outputs.
V2: rebase
V3: Addressed review comments from Ville
- add enum crtc_output_format instead of bool ycbcr420
- use crtc_output_format=4:4:4 for modeset of LSPCON 4:2:0 output
cases in this way we will have YCBCR 4:4:4 framework ready (except
the ABI part)
V4: Added r-b from Maarten (for v3)
Addressed review comments from Ville:
- Do not add a non-atomic state variable to determine lspcon output.
Instead add bool in CRTC state to indicate lspcon based scaling.
V5: Addressed review comments from Ville:
- Change the state bool name from external scaling to something more
relavent.
- Keep the info and adjusted_mode structures const.
- use crtc_state instead of pipe_config.
- Push all the config change into lspcon_ycbcr420_config function.
V6: Rebase, small changes to accommodate changes in patch 2.
V7: Fixed checkpatch warnings for alignment
V8: Rebase
PS: Ignored following warnings to match the current formatting:
drm/i915: Add YCBCR 4:2:0/4:4:4 support for LSPCON
-:53: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#53: FILE: drivers/gpu/drm/i915/i915_reg.h:8721:
+#define TRANS_MSA_SAMPLING_444 (2<<1)
^
-:54: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#54: FILE: drivers/gpu/drm/i915/i915_reg.h:8722:
+#define TRANS_MSA_CLRSP_YCBCR (2<<3)
V9: Rebase
V10: Rebase
V11: Rebase
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-8-git-send-email-shashank.sharma@intel.com
This patch adds an enum "intel_output_format" to represent
the output format of a particular CRTC. This enum will be
used to produce a RGB/YCBCR4:4:4/YCBCR4:2:0 output format
during the atomic modeset calculations.
V5:
- Created this separate patch to introduce and init output_format.
- Initialize parameters of output_format_str respectively (Jani N).
- Call it intel_output_format than crtc_output_format(Ville).
- Set output format in pipe_config for every encoder (Ville).
- Get rid of extra DRM_DEBUG_KMS during get_pipe_config (Ville)
V6: Rebase
V7: Fixed alignment warnings (checkpatch)
V8: Another check[atch warning for alignment
V9: Rebase
V10: Rebase on top of DSI restructure
V11: Addressed review comment from Ville
- Set CRTC format for pre-HSW get_pipe_config() function too.
Added Ville's R-B
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-1-git-send-email-shashank.sharma@intel.com
Always print out the information whether the port and sink can each
do MST. And let's include the modparam in the debug output as well.
Makes life a little less confusing when you don't have to wonder
why MST isn't kicking in.
This does cause a slight change in our behaviour towards the sink.
Previously we only read the MSTM_CAP register after passing all
the other checks. Now we will read that register regardless. Hopefully
some crazy sink doesn't get confused by a simple register read.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003184210.1306-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
We've opted to use the maximum link rate and lane count for eDP panels,
because typically the maximum supported configuration reported by the
panel has matched the native resolution requirements of the panel, and
optimizing the link has lead to problems.
With eDP 1.4 rate select method and DSC features, this is decreasingly
the case. There's a need to optimize the link parameters. Moreover,
already eDP 1.3 states fast link with fewer lanes is preferred over the
wide and slow. (Wide and slow should still be more reliable for longer
cable lengths.)
Additionally, there have been reports of panels failing on arbitrary
link configurations, although arguably all configurations they claim to
support should work.
Optimize eDP 1.4+ link config fast and narrow.
Side note: The implementation has a near duplicate of the link config
function, with just the two inner for loops turned inside out. Perhaps
there'd be a way to make this, say, more table driven to reduce the
duplication, but seems like that would lead to duplication in the table
generation. We'll also have to see how the link config optimization for
DSC turns out.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: "Lee, Shawn C" <shawn.c.lee@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105267
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180905095321.13843-1-jani.nikula@intel.com
Comment claims link needs to be retrained because the connected sink raised
a long pulse to indicate link loss. If the sink did so,
intel_dp_hotplug() would have handled link retraining. Looking at the
logs in Bugzilla referenced in commit '3cf71bc9904d ("drm/i915: Re-apply
Perform link quality check, unconditionally during long pulse"")', the
issue is that the sink does not trigger an interrupt. What we want is
->detect() from user space to check link status and retrain. Ville's
review for the original patch also indicates the same root cause. So,
rewrite the comment.
v2: Patch split and rewrote comment.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jan-Marek Glogowski <glogow@fbihome.de>
References: 3cf71bc990 ("drm/i915: Re-apply "Perform link quality check, unconditionally during long pulse"")
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-1-dhinakaran.pandiyan@intel.com
So far we have only been calling
drm_connector_init_panel_orientation_property(), which checks for
panel orientation quirks in the drm_panel_orientation_quirks.c file,
for DSI panels as so far only devices with DSI panels have had panels
which are not mounted up right.
The new GPD win2 device uses a portrait screen in a landscape case,
so now we've a device with an eDP panel which needs the panel-orientation
property to let the fbcon code and userspace know that the image needs to
be fixed-up.
This commit makes intel_edp_init_connector() call
drm_connector_init_panel_orientation_property() so that the property
gets added.
Reported-and-tested-by: russianneuromancer@ya.ru
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180909133457.10636-2-hdegoede@redhat.com
drm-misc-next for 4.20:
UAPI Changes:
- None
Cross-subsystem Changes:
- None
Core Changes:
- Allow drivers to disable features with per-device granularity (Ville)
- Use EOPNOTSUPP when iface/feature is unsupported instead of
EINVAL/errno soup (Chris)
- Simplify M/N DP quirk by using constant N to limit size of M/N (Shawn)
- add quirk for LG LP140WF6-SPM1 eDP panel (Shawn)
Driver Changes:
- i915/amdgpu: Disable DRIVER_ATOMIC for older/unsupported devices (Ville)
- sun4i: add support for R40 HDMI PHY (Icenowy)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Lee, Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20180919200218.GA186644@art_vandelay
This re-applies the workaround for "some DP sinks, [which] are a
little nuts" from commit 1a36147bb9 ("drm/i915: Perform link
quality check unconditionally during long pulse").
It makes the secondary AOC E2460P monitor connected via DP to an
acer Veriton N4640G usable again.
This hunk was dropped in commit c85d200e83 ("drm/i915: Move SST
DP link retraining into the ->post_hotplug() hook")
Fixes: c85d200e83 ("drm/i915: Move SST DP link retraining into the ->post_hotplug() hook")
[Cleaned up commit message, added stable cc]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jan-Marek Glogowski <glogow@fbihome.de>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20180825191035.3945-1-lyude@redhat.com
Unlike the other ports, TC ports are not available to use as soon as
we get a hotplug. The TC PHYs can be shared between multiple
controllers: display, USB, etc. As a result, handshaking through FIA
is required around connect and disconnect to cleanly transfer
ownership with the controller and set the type-C power state.
This patch implements the flow sequences described by our
specification. We opt to grab ownership of the ports as soon as we get
the hotplugs in order to simplify the interactions and avoid surprises
in the user space side. We may consider changing this in the future,
once we improve our testing capabilities on this area.
v2:
* This unifies the DP and HDMI patches so we can discuss everything
at once so people looking at random single patches can actually
understand the direction.
* I found out the spec was updated a while ago. There's a small
difference in the connect flow and the patch was updated for that.
* Our spec also now gives a good explanation on what is really
happening. As a result, comments were added.
* Add some more comments as requested by Rodrigo (Rodrigo).
v3:
* Downgrade a DRM_ERROR that shouldn't ever happen but we can't act
on in case it does (Chris).
BSpec: 21750, 4250.
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180801173441.9789-1-paulo.r.zanoni@intel.com
The short pulse handler checks if channel equalization is okay and
goes onto retrain a link if there are active MST links. This retraining
path is not meant for new MST connections, but due to a bug elsewhere, if
active_mst_links is < 0 the boolean check for active_mst_links passes and
we proceed to retrain a new link. This results in a sequence of failed link
training attempts, most likely due to the hardware not setup for link
training at that point i.e., missing the DDI pre_enable sequence.
[ 80.301272] [drm:intel_dp_check_mst_status] channel EQ not ok, retraining
[ 80.301312] [drm:intel_ddi_prepare_link_retrain] *ERROR* Timeout waiting for DDI BUF C idle bit
The above error gives us a hint something went wrong before link
training started.
Check for a positive value of active_mst_links and throw in a warning for
invalid active_mst_links as debug aid.
Cc: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Tested-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180718171943.3246-1-dhinakaran.pandiyan@intel.com
