Renesas ARM Based SoC Fixes for v4.20
* R-Car V3H (r8a77980) based Condor board
- Switch from EtherAVB to GEther to match offical boards
* RZ/G2E (ra8774c0) SoC: correct documentation of part number
* R-Car H3 (r8a7795) SoC: reinstate all DMA channels on HSCIF2
* tag 'renesas-fixes-for-v4.20' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: condor: switch from EtherAVB to GEther
dt-bindings: arm: Fix RZ/G2E part number
arm64: dts: renesas: r8a7795: add missing dma-names on hscif2
Signed-off-by: Olof Johansson <olof@lixom.net>
Exercising the gpu reloc path strenuously revealed an issue where the
updated relocations (from MI_STORE_DWORD_IMM) were not being observed
upon execution. After some experiments with adding pipecontrols (a lot
of pipecontrols (32) as gen4/5 do not have a bit to wait on earlier pipe
controls or even the current on), it was discovered that we merely
needed to delay the EMIT_INVALIDATE by several flushes. It is important
to note that it is the EMIT_INVALIDATE as opposed to the EMIT_FLUSH that
needs the delay as opposed to what one might first expect -- that the
delay is required for the TLB invalidation to take effect (one presumes
to purge any CS buffers) as opposed to a delay after flushing to ensure
the writes have landed before triggering invalidation.
Testcase: igt/gem_tiled_fence_blits
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181105094305.5767-1-chris@chris-wilson.co.uk
The order in which the frequencies are displayed in cpufreq stats
depends on the order in which the frequencies were sorted in the
frequency table provided to cpufreq core by the cpufreq driver. They can
be completely unsorted as well.
The documentation's claim that the stats will be sorted in descending
order is hence incorrect and here is an attempt to fix it.
Reported-by: Pavel <pavel2000@ngs.ru>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
TRACE_INCLUDE_PATH and TRACE_INCLUDE_FILE are used by
<trace/define_trace.h>, so like that #include, they should
be outside #ifdef protection.
They also need to be #undefed before defining, in case multiple trace
headers are included by the same C file. This became the case on
book3e after commit cf4a608515 ("powerpc/mm: Add missing tracepoint for
tlbie"), leading to the following build error:
CC arch/powerpc/kvm/powerpc.o
In file included from arch/powerpc/kvm/powerpc.c:51:0:
arch/powerpc/kvm/trace.h:9:0: error: "TRACE_INCLUDE_PATH" redefined
[-Werror]
#define TRACE_INCLUDE_PATH .
^
In file included from arch/powerpc/kvm/../mm/mmu_decl.h:25:0,
from arch/powerpc/kvm/powerpc.c:48:
./arch/powerpc/include/asm/trace.h:224:0: note: this is the location of
the previous definition
#define TRACE_INCLUDE_PATH asm
^
cc1: all warnings being treated as errors
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commit d87161bea4.
The issues that forced us to disable blk_mq for ufs have been resolved.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Three regressions
- Revert frame counter support
. This patch fixes a issue which doesn't work extension and clone
mode because some CRTC devices don't provide frame counter value
properly.
- Fix lack of fbdev on Rinato and trats boards.
. This patch considers for connector to be registered by DSI after
DRM device is registered, and also it makes fbdev initializaion
to be done even if no connector at the moment.
- Check for dsi->panel object correctly
. This patch fixes checking for dsi->panel. of_drm_find_panel
function returns panel object or error value so error value
should be checked using IS_ERR macro.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1541407733-7632-1-git-send-email-inki.dae@samsung.com
ext4_mark_iloc_dirty() callers expect that it releases iloc->bh
even if it returns an error.
Fixes: 0db1ff222d ("ext4: add shutdown bit and check for it")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org # 4.11
Similar to ppfeaturemask. Allows you to selectively enable/disable
DC features.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The value is dependent on whether fbc is available.
v2: only check if num_pipes is valid
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
RETIMER_REDRIVER_INFO shows the buffer as a decimal value with a '0x'
prefix, which is somewhat misleading.
Fix it to print hexadecimal, as was intended.
Fixes: 2f14bc89("drm/amd/display: add retimer log for HWQ tuning use.")
Cc: Charlene Liu <charlene.liu@amd.com>
Cc: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 0cafc82fae.
This breaks some apps that assume 0 is minimum brightness.
Revert for 4.20. This is fixed properly for drm-next/4.21 in:
"drm/amd: Don't fail on backlight = 0"
However, that patch depends on more extensive changes to the
backlight interface which are too invasive for -fixes.
Fixes: Bugzilla: https://bugs.freedesktop.org/108668
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The split out of the hard lockup detector exposed two new weak functions,
but no prototypes for them, which triggers the build warning:
kernel/watchdog.c:109:12: warning: no previous prototype for ‘watchdog_nmi_enable’ [-Wmissing-prototypes]
kernel/watchdog.c:115:13: warning: no previous prototype for ‘watchdog_nmi_disable’ [-Wmissing-prototypes]
Add the prototypes.
Fixes: 73ce0511c4 ("kernel/watchdog.c: move hardlockup detector to separate file")
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Babu Moger <babu.moger@oracle.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180606194232.17653-1-malat@debian.org
The timecounter needs to be updated at least once per ~550 seconds in
order to avoid a 40-bit SYSTIM timestamp to be misinterpreted as an old
timestamp.
Since commit 500462a9de ("timers: Switch to a non-cascading wheel"),
scheduling of delayed work seems to be less accurate and a requested
delay of 540 seconds may actually be longer than 550 seconds. Also, the
PHC may be adjusted to run up to 6% faster than real time and the system
clock up to 10% slower. Shorten the delay to 360 seconds to be sure the
timecounter is updated in time.
This fixes an issue with HW timestamps on 82580/I350/I354 being off by
~1100 seconds for few seconds every ~9 minutes.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the driver does a TSO offload the bytecount sent to
netdev_tx_sent_queue will be incorrect. This is because in ice_tso we
overwrite the initial value that we set in ice_tx_map. This creates a
mismatch between the Tx and Tx clean flow. In the Tx clean flow we
calculate the bytecount (called total_bytes) as we clean the
descriptors so the value used in the Tx clean path is correct. Fix this
by using += in ice_tso instead of =. This fixes the mismatch in
bytecount mentioned above.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Prior to this commit the driver was running into tx_timeouts when a
queue was stressed enough. This was happening because the HW tail
and SW tail (NTU) were incorrectly out of sync. Consequently this was
causing the HW head to collide with the HW tail, which to the hardware
means that all descriptors posted for Tx have been processed.
Due to the Tx logic used in the driver SW tail and HW tail are allowed
to be out of sync. This is done as an optimization because it allows the
driver to write HW tail as infrequently as possible, while still
updating the SW tail index to keep track. However, there are situations
where this results in the tail never getting updated, resulting in Tx
timeouts.
Tx HW tail write condition:
if (netif_xmit_stopped(txring_txq(tx_ring) || !skb->xmit_more)
writel(sw_tail, tx_ring->tail);
An issue was found in the Tx logic that was causing the afore mentioned
condition for updating HW tail to never happen, causing tx_timeouts.
In ice_xmit_frame_ring we calculate how many descriptors we need for the
Tx transaction based on the skb the kernel hands us. This is then passed
into ice_maybe_stop_tx along with some extra padding to determine if we
have enough descriptors available for this transaction. If we don't then
we return -EBUSY to the stack, otherwise we move on and eventually
prepare the Tx descriptors accordingly in ice_tx_map and set
next_to_watch. In ice_tx_map we make another call to ice_maybe_stop_tx
with a value of MAX_SKB_FRAGS + 4. The key here is that this value is
possibly less than the value we sent in the first call to
ice_maybe_stop_tx in ice_xmit_frame_ring. Now, if the number of unused
descriptors is between MAX_SKB_FRAGS + 4 and the value used in the first
call to ice_maybe_stop_tx in ice_xmit_frame_ring then we do not update
the HW tail because of the "Tx HW tail write condition" above. This is
because in ice_maybe_stop_tx we return success from ice_maybe_stop_tx
instead of calling __ice_maybe_stop_tx and subsequently calling
netif_stop_subqueue, which sets the __QUEUE_STATE_DEV_XOFF bit. This
bit is then checked in the "Tx HW tail write condition" by calling
netif_xmit_stopped and subsequently updating HW tail if the
afore mentioned bit is set.
In ice_clean_tx_irq, if next_to_watch is not NULL, we end up cleaning
the descriptors that HW sets the DD bit on and we have the budget. The
HW head will eventually run into the HW tail in response to the
description in the paragraph above.
The next time through ice_xmit_frame_ring we make the initial call to
ice_maybe_stop_tx with another skb from the stack. This time we do not
have enough descriptors available and we return NETDEV_TX_BUSY to the
stack and end up setting next_to_watch to NULL.
This is where we are stuck. In ice_clean_tx_irq we never clean anything
because next_to_watch is always NULL and in ice_xmit_frame_ring we never
update HW tail because we already return NETDEV_TX_BUSY to the stack and
eventually we hit a tx_timeout.
This issue was fixed by making sure that the second call to
ice_maybe_stop_tx in ice_tx_map is passed a value that is >= the value
that was used on the initial call to ice_maybe_stop_tx in
ice_xmit_frame_ring. This was done by adding the following defines to
make the logic more clear and to reduce the chance of mucking this up
again:
ICE_CACHE_LINE_BYTES 64
ICE_DESCS_PER_CACHE_LINE (ICE_CACHE_LINE_BYTES / \
sizeof(struct ice_tx_desc))
ICE_DESCS_FOR_CTX_DESC 1
ICE_DESCS_FOR_SKB_DATA_PTR 1
The ICE_CACHE_LINE_BYTES being 64 is an assumption being made so we
don't have to figure this out on every pass through the Tx path. Instead
I added a sanity check in ice_probe to verify cache line size and print
a message if it's not 64 Bytes. This will make it easier to file issues
if they are seen when the cache line size is not 64 Bytes when reading
from the GLPCI_CNF2 register.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the remove path, the vsi->netdev is being set to NULL before the call
to free vectors. This is causing the netif_napi_del call to never be made.
Add a call to ice_napi_del to the same location as the calls to
unregister_netdev and just prior to them. This will use the reverse flow
as the register and netif_napi_add calls.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_restore_vlan and active_vlans were originally put in place to
reprogram VLAN filters in the replay path. This is now done as part
of the much broader VSI rebuild/replay framework. So remove both
ice_restore_vlan and active_vlans
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The remove path does not currently check to see if a
reset is in progress before proceeding. This can cause
a resource collision resulting in various types of errors.
Check for reset in progress and wait for a reasonable
amount of time before allowing the remove to progress.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
vSMP dependency on pv_irq_ops has been removed some years ago, but the code
still deals with pv_irq_ops.
In short, "cap & ctl & (1 << 4)" is always returning 0, so all
PARAVIRT/PARAVIRT_XXL code related to that can be removed.
However, the rest of the code depends on CONFIG_PCI, so fix it accordingly.
Rename set_vsmp_pv_ops to set_vsmp_ctl as the original name does not make
sense anymore.
Signed-off-by: Eial Czerwacki <eial@scalemp.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Shai Fultheim <shai@scalemp.com>
Cc: Juergen Gross <jgross@suse.com>
Link: https://lkml.kernel.org/r/1541439114-28297-1-git-send-email-eial@scalemp.com
Add a function to check whether there is at least one plane that
supports a specific format and modifier combination. Drivers can
use this to reject unsupported formats/modifiers in .fb_create().
v2: Accept anyformat if the driver doesn't do planes (Eric)
s/planes_have_format/any_plane_has_format/ (Eric)
Check the modifier as well since we already have a function
that does both
v3: Don't do the check in the core since we may not know the
modifier yet, instead export the function and let drivers
call it themselves
Cc: Eric Anholt <eric@anholt.net>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029183453.28541-1-ville.syrjala@linux.intel.com
