In commit 47b7e7f828, this bit was removed at the same time the
RT6_LOOKUP_F_IFACE flag was removed. However, it is needed when
link-local addresses are used, which is a very common case: when
packets are routed, neighbor solicitations are done using link-local
addresses. For example, the following neighbor solicitation is not
matched by "-m rpfilter":
IP6 fe80::5254:33ff:fe00:1 > ff02::1:ff00:3: ICMP6, neighbor
solicitation, who has 2001:db8::5254:33ff:fe00:3, length 32
Commit 47b7e7f828 doesn't quite explain why we shouldn't use
RT6_LOOKUP_F_IFACE in the rpfilter case. I suppose the interface check
later in the function would make it redundant. However, the remaining
of the routing code is using RT6_LOOKUP_F_IFACE when there is no
source address (which matches rpfilter's case with a non-unicast
destination, like with neighbor solicitation).
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Fixes: 47b7e7f828 ("netfilter: don't set F_IFACE on ipv6 fib lookups")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This reverts commit f92b40a8b2
("netfilter: core: only allow one nat hook per hook point"), this
limitation is no longer needed. The nat core now invokes these
functions and makes sure that hook evaluation stops after a mapping is
created and a null binding is created otherwise.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently the packet rewrite and instantiation of nat NULL bindings
happens from the protocol specific nat backend.
Invocation occurs either via ip(6)table_nat or the nf_tables nat chain type.
Invocation looks like this (simplified):
NF_HOOK()
|
`---iptable_nat
|
`---> nf_nat_l3proto_ipv4 -> nf_nat_packet
|
new packet? pass skb though iptables nat chain
|
`---> iptable_nat: ipt_do_table
In nft case, this looks the same (nft_chain_nat_ipv4 instead of
iptable_nat).
This is a problem for two reasons:
1. Can't use iptables nat and nf_tables nat at the same time,
as the first user adds a nat binding (nf_nat_l3proto_ipv4 adds a
NULL binding if do_table() did not find a matching nat rule so we
can detect post-nat tuple collisions).
2. If you use e.g. nft_masq, snat, redir, etc. uses must also register
an empty base chain so that the nat core gets called fro NF_HOOK()
to do the reverse translation, which is neither obvious nor user
friendly.
After this change, the base hook gets registered not from iptable_nat or
nftables nat hooks, but from the l3 nat core.
iptables/nft nat base hooks get registered with the nat core instead:
NF_HOOK()
|
`---> nf_nat_l3proto_ipv4 -> nf_nat_packet
|
new packet? pass skb through iptables/nftables nat chains
|
+-> iptables_nat: ipt_do_table
+-> nft nat chain x
`-> nft nat chain y
The nat core deals with null bindings and reverse translation.
When no mapping exists, it calls the registered nat lookup hooks until
one creates a new mapping.
If both iptables and nftables nat hooks exist, the first matching
one is used (i.e., higher priority wins).
Also, nft users do not need to create empty nat hooks anymore,
nat core always registers the base hooks that take care of reverse/reply
translation.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This adds the infrastructure to register nat hooks with the nat core
instead of the netfilter core.
nat hooks are used to configure nat bindings. Such hooks are registered
from ip(6)table_nat or by the nftables core when a nat chain is added.
After next patch, nat hooks will be registered with nf_nat instead of
netfilter core. This allows to use many nat lookup functions at the
same time while doing the real packet rewrite (nat transformation) in
one place.
This change doesn't convert the intended users yet to ease review.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This will allow the nat core to reuse the nf_hook infrastructure
to maintain nat lookup functions.
The raw versions don't assume a particular hook location, the
functions get added/deleted from the hook blob that is passed to the
functions.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Will be used in followup patch when nat types no longer
use nf_register_net_hook() but will instead register with the nat core.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The ip(6)tables nat table is currently receiving skbs from the netfilter
core, after a followup patch skbs will be coming from the netfilter nat
core instead, so the table is no longer backed by normal hook_ops.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Copy-pasted, both l3 helpers almost use same code here.
Split out the common part into an 'inet' helper.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ECN signals currently forces TCP to enter quickack mode for
up to 16 (TCP_MAX_QUICKACKS) following incoming packets.
We believe this is not needed, and only sending one immediate ack
for the current packet should be enough.
This should reduce the extra load noticed in DCTCP environments,
after congestion events.
This is part 2 of our effort to reduce pure ACK packets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to add finer control of the number of ACK packets sent after
ECN events.
This patch is not changing current behavior, it only enables following
change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial net_device implementation used ingress_lock spinlock to synchronize
ingress path of device. This lock was used in both process and bh context.
In some code paths action map lock was obtained while holding ingress_lock.
Commit e1e992e52f ("[NET_SCHED] protect action config/dump from irqs")
modified actions to always disable bh, while using action map lock, in
order to prevent deadlock on ingress_lock in softirq. This lock was removed
from net_device, so disabling bh, while accessing action map, is no longer
necessary.
Replace all action idr spinlock usage with regular calls that do not
disable bh.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring consistency to ipv6 route replace and append semantics.
Remove rt6_qualify_for_ecmp which is just guess work. It fails in 2 cases:
1. can not replace a route with a reject route. Existing code appends
a new route instead of replacing the existing one.
2. can not have a multipath route where a leg uses a dev only nexthop
Existing use cases affected by this change:
1. adding a route with existing prefix and metric using NLM_F_CREATE
without NLM_F_APPEND or NLM_F_EXCL (ie., what iproute2 calls
'prepend'). Existing code auto-determines that the new nexthop can
be appended to an existing route to create a multipath route. This
change breaks that by requiring the APPEND flag for the new route
to be added to an existing one. Instead the prepend just adds another
route entry.
2. route replace. Existing code replaces first matching multipath route
if new route is multipath capable and fallback to first matching
non-ECMP route (reject or dev only route) in case one isn't available.
New behavior replaces first matching route. (Thanks to Ido for spotting
this one)
Note: Newer iproute2 is needed to display multipath routes with a dev-only
nexthop. This is due to a bug in iproute2 and parsing nexthops.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sctp uses inet_dgram_connect as its proto_ops .connect, and the flags
param can't be passed into its proto .connect where this flags is really
needed.
sctp works around it by getting flags from socket file in __sctp_connect.
It works for connecting from userspace, as inherently the user sock has
socket file and it passes f_flags as the flags param into the proto_ops
.connect.
However, the sock created by sock_create_kern doesn't have a socket file,
and it passes the flags (like O_NONBLOCK) by using the flags param in
kernel_connect, which calls proto_ops .connect later.
So to fix it, this patch defines a new proto_ops .connect for sctp,
sctp_inet_connect, which calls __sctp_connect() directly with this
flags param. After this, the sctp's proto .connect can be removed.
Note that sctp_inet_connect doesn't need to do some checks that are not
needed for sctp, which makes thing better than with inet_dgram_connect.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add check that egress MTU can handle packet to be forwarded. If
the MTU is less than the packet length, return 0 meaning the
packet is expected to continue up the stack for help - eg.,
fragmenting the packet or sending an ICMP.
The XDP path needs to leverage the FIB entry for an MTU on the
route spec or an exception entry for a given destination. The
skb path lets is_skb_forwardable decide if the packet can be
sent.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Determine path MTU from a FIB lookup result. Logic is based on
ip6_dst_mtu_forward plus lookup of nexthop exception.
Add ip6_dst_mtu_forward to ipv6_stubs to handle access by core
bpf code.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Determine path MTU from a FIB lookup result. Logic is a distillation of
ip_dst_mtu_maybe_forward.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
As suggested by Daniel Borkmann, the umem setup code was a too
defensive and complex. Here, we reduce the number of checks. Also, the
memory pinning is now folded into the umem creation, and we do correct
locking.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Here, we add a missing write-barrier, and use READ_ONCE for the
data-dependency barrier.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In this commit we remove the explicit ring structure from the the
uapi. It is tricky for an uapi to depend on a certain L1 cache line
size, since it can differ for variants of the same architecture. Now,
we let the user application determine the offsets of the producer,
consumer and descriptors by asking the socket via getsockopt.
A typical flow would be (Rx ring):
struct xdp_mmap_offsets off;
struct xdp_desc *ring;
u32 *prod, *cons;
void *map;
...
getsockopt(fd, SOL_XDP, XDP_MMAP_OFFSETS, &off, &optlen);
map = mmap(NULL, off.rx.desc +
NUM_DESCS * sizeof(struct xdp_desc),
PROT_READ | PROT_WRITE,
MAP_SHARED | MAP_POPULATE, sfd,
XDP_PGOFF_RX_RING);
prod = map + off.rx.producer;
cons = map + off.rx.consumer;
ring = map + off.rx.desc;
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Validate the queue id against both Rx and Tx on the netdev. Also, make
sure that the queue exists at xmit time.
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Supporting rebind, i.e. after a successful bind the process can call
bind again without closing the socket, makes the AF_XDP setup state
machine more complex. Constrain the state space, by not supporting
rebind.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Some drivers may call this function when regdb is not initialized yet,
so we need to make sure regdb is valid before trying to access it.
Make sure regdb is initialized before trying to access it in
reg_query_regdb_wmm() and query_regdb().
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 7ea3e110f2 seems to have
introduced:
net/wireless/nl80211.c: In function ‘nl80211_get_station’:
net/wireless/nl80211.c:4802:34: error: incompatible type for argument 1 of ‘cfg80211_sinfo_release_content’
cfg80211_sinfo_release_content(sinfo);
^~~~~
In file included from net/wireless/nl80211.c:24:0:
./include/net/cfg80211.h:5721:20: note: expected ‘struct station_info *’ but argument is of type ‘struct station_info’
static inline void cfg80211_sinfo_release_content(struct station_info *sinfo)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 7ea3e110f2 ("cfg80211: release station info tidstats where needed")
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2018-05-18
Here's the first bluetooth-next pull request for the 4.18 kernel:
- Refactoring of the btbcm driver
- New USB IDs for QCA_ROME and LiteOn controllers
- Buffer overflow fix if the controller sends invalid advertising data length
- Various cleanups & fixes for Qualcomm controllers
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ip6gre and ip6erspan share single metadata mode device,
using 'collect_md_tun'. Thus, when doing:
ip link add dev ip6gre11 type ip6gretap external
ip link add dev ip6erspan12 type ip6erspan external
RTNETLINK answers: File exists
simply fails due to the 2nd tries to create the same collect_md_tun.
The patch fixes it by adding a separate collect md tunnel device
for the ip6erspan, 'collect_md_tun_erspan'. As a result, a couple
of places need to refactor/split up in order to distinguish ip6gre
and ip6erspan.
First, move the collect_md check at ip6gre_tunnel_{unlink,link} and
create separate function {ip6gre,ip6ersapn}_tunnel_{link_md,unlink_md}.
Then before link/unlink, make sure the link_md/unlink_md is called.
Finally, a separate ndo_uninit is created for ip6erspan. Tested it
using the samples/bpf/test_tunnel_bpf.sh.
Fixes: ef7baf5e08 ("ip6_gre: add ip6 erspan collect_md mode")
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the attrs and allow to expose port flavour to user via devlink.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each driver implements physical port name generation by itself. However
as devlink has all needed info, it can easily do the job for all its
users. So implement this helper in devlink.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink ports can have specific flavour according to the purpose of use.
This patch extend attrs_set so the driver can say which flavour port
has. Initial flavours are:
physical, cpu, dsa
User can query this to see right away what is the purpose of each port.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change existing setter for split port information into more generic
attrs setter. Alongside with that, allow to set port number and subport
number for split ports.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently sk_msg programs only have access to the raw data. However,
it is often useful when building policies to have the policies specific
to the socket endpoint. This allows using the socket tuple as input
into filters, etc.
This patch adds ctx access to the sock fields.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch splits up the functions smc_connect_rdma and smc_listen_work
into smaller functions.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the function smc_buf_free to use the SMC link group
instead of the link as function parameter. Also, it changes the order of
the other two parameters.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consists of Christmas tree fixes and removal of an unneeded
function parameter.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves a CDC sanity check from smc_cdc_msg_recv_action() to
the other sanity checks in smc_cdc_rx_handler(). While doing this, it
simplifies smc_cdc_msg_recv() and removes unneeded function parameters.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC connection and buffer handling belong to smc_core. So, this patch
moves this code from smc.h to smc_core.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the write offset within the RMB is calculated on each write
operation although it is fixed for each connection. With this patch, the
offset is calculated once and stored in a connection specific variable.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The connection index is actually a RMBE index. So, this patch changes
the name accordingly.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the global link group list to smc_core where the link
group functions are. To make this work, it moves code in af_smc and
smc_ib that operates on the link group list to smc_core as well.
While at it, the link group counter is integrated into the list
structure and initialized to zero.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In addition to the buffer references, SMC currently stores the sizes of
the receive and send buffers in each connection as separate variables.
This patch introduces a buffer length variable in the common buffer
descriptor and uses this length instead.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if commit 1d27732f41 ("net: dsa: setup and teardown ports") indicated
that registering a devlink instance for unused ports is not a problem, and this
is true, this can be confusing nonetheless, so let's not do it.
Fixes: 1d27732f41 ("net: dsa: setup and teardown ports")
Reported-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While removing queues from the XPS map, the individual CPU ID
alone was used to index the CPUs map, this should be changed to also
factor in the traffic class mapping for the CPU-to-queue lookup.
Fixes: 184c449f91 ("net: Add support for XPS with QoS via traffic classes")
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
