Now that it is possible to do dynamic allocations during the
identification phase, convert the onfi_params structure (which is only
needed with ONFI compliant chips) into a pointer that will be allocated
only if needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Commit 59b356ffd0 ("mtd: m25p80: restore the status of SPI flash when
exiting") is the latest from a long history of attempts to add reboot
handling to handle stateful addressing modes on SPI flash. Some prior
mostly-related discussions:
http://lists.infradead.org/pipermail/linux-mtd/2013-March/046343.html
[PATCH 1/3] mtd: m25p80: utilize dedicated 4-byte addressing commands
http://lists.infradead.org/pipermail/barebox/2014-September/020682.html
[RFC] MTD m25p80 3-byte addressing and boot problem
http://lists.infradead.org/pipermail/linux-mtd/2015-February/057683.html
[PATCH 2/2] m25p80: if supported put chip to deep power down if not used
Previously, attempts to add reboot-time software reset handling were
rejected, but the latest attempt was not.
Quick summary of the problem:
Some systems (e.g., boot ROM or bootloader) assume that they can read
initial boot code from their SPI flash using 3-byte addressing. If the
flash is left in 4-byte mode after reset, these systems won't boot. The
above patch provided a shutdown/remove hook to attempt to reset the
addressing mode before we reboot. Notably, this patch misses out on
huge classes of unexpected reboots (e.g., crashes, watchdog resets).
Unfortunately, it is essentially impossible to solve this problem 100%:
if your system doesn't know how to reset the SPI flash to power-on
defaults at initialization time, no amount of software can really rescue
you -- there will always be a chance of some unexpected reset that
leaves your flash in an addressing mode that your boot sequence didn't
expect.
While it is not directly harmful to perform hacks like the
aforementioned commit on all 4-byte addressing flash, a
properly-designed system should not need the hack -- and in fact,
providing this hack may mask the fact that a given system is indeed
broken. So this patch attempts to apply this unsound hack more narrowly,
providing a strong suggestion to developers and system designers that
this is truly a hack. With luck, system designers can catch their errors
early on in their development cycle, rather than applying this hack long
term. But apparently enough systems are out in the wild that we still
have to provide this hack.
Document a new device tree property to denote systems that do not have a
proper hardware (or software) reset mechanism, and apply the hack (with
a loud warning) only in this case.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Current DMA direction definitions in pci-dma-compat.h and dma-direction.h
are mirrored in value. Unify them to enhance readability and avoid
possible inconsistency.
Signed-off-by: Shunyong Yang <shunyong.yang@hxt-semitech.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Joey Zheng <yu.zheng@hxt-semitech.com>
A bit larger this time around, due to introduction of "dpu1" support
for the display controller in sdm845 and beyond. This has been on
list and undergoing refactoring since Feb (going from ~110kloc to
~30kloc), and all my review complaints have been addressed, so I'd be
happy to see this upstream so further feature work can procede on top
of upstream.
Also includes the gpu coredump support, which should be useful for
debugging gpu crashes. And various other misc fixes and such.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGv-8y3zguY0Mj1vh=o+vrv_bJ8AwZ96wBXYPvMeQT2XcA@mail.gmail.com
Note which task is using the entity and only kill it if the last user of
the entity is killed. This should prevent problems when entities are leaked to
child processes.
v2: add missing kernel doc
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: Nayan Deshmukh <nayan26deshmukh@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dm_kcopyd_copy() only ever returns 0 so there is no need for callers to
account for possible failure. Same goes for dm_kcopyd_zero().
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
We never use RCU protection for it, just a lot of cargo-cult
rcu_deference_protects calls.
Note that we do keep the kfree_rcu call for it, as the references through
struct sock are RCU protected and thus might require a grace period before
freeing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a live data migration event at the NFS server, the client may send
I/O requests to the wrong server, causing a live hang due to repeated
recovery events. On the wire, this will appear as an I/O request failing
with NFS4ERR_BADSESSION, followed by successful CREATE_SESSION, repeatedly.
NFS4ERR_BADSSESSION is returned because the session ID being used was
issued by the other server and is not valid at the old server.
The failure is caused by async worker threads having cached the transport
(xprt) in the rpc_task structure. After the migration recovery completes,
the task is redispatched and the task resends the request to the wrong
server based on the old value still present in tk_xprt.
The solution is to recompute the tk_xprt field of the rpc_task structure
so that the request goes to the correct server.
Signed-off-by: Bill Baker <bill.baker@oracle.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Helen Chao <helen.chao@oracle.com>
Fixes: fb43d17210 ("SUNRPC: Use the multipath iterator to assign a ...")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The existing rpc_print_iostats has a few shortcomings. First, the naming
is not consistent with other functions in the kernel that display stats.
Second, it is really displaying stats for an rpc_clnt structure as it
displays both xprt stats and per-op stats. Third, it does not handle
rpc_clnt clones, which is important for the one in-kernel tree caller
of this function, the NFS client's nfs_show_stats function.
Fix all of the above by renaming the rpc_print_iostats to
rpc_clnt_show_stats and looping through any rpc_clnt clones via
cl_parent.
Once this interface is fixed, this addresses a problem with NFSv4.
Before this patch, the /proc/self/mountstats always showed incorrect
counts for NFSv4 lease and session related opcodes such as SEQUENCE,
RENEW, SETCLIENTID, CREATE_SESSION, etc. These counts were always 0
even though many ops would go over the wire. The reason for this is
there are multiple rpc_clnt structures allocated for any given NFSv4
mount, and inside nfs_show_stats() we callled into rpc_print_iostats()
which only handled one of them, nfs_server->client. Fix these counts
by calling sunrpc's new rpc_clnt_show_stats() function, which handles
cloned rpc_clnt structs and prints the stats together.
Note that one side-effect of the above is that multiple mounts from
the same NFS server will show identical counts in the above ops due
to the fact the one rpc_clnt (representing the NFSv4 client state)
is shared across mounts.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Currently drivers have to check if they already have a umem
installed for a given queue and return an error if so. Make
better use of XDP_QUERY_XSK_UMEM and move this functionality
to the core.
We need to keep rtnl across the calls now.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Björn Töpel <bjorn.topel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to depend on real_num_rx_queues as a upper bound for sanity
checks. For AF_XDP socket validation it's useful if the check behaves
the same regardless of CONFIG_SYSFS setting.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PCI device is detected, pdev->is_added is set to 1 and proc and
sysfs entries are created.
When the device is removed, pdev->is_added is checked for one and then
device is detached with clearing of proc and sys entries and at end,
pdev->is_added is set to 0.
is_added and is_busmaster are bit fields in pci_dev structure sharing same
memory location.
A strange issue was observed with multiple removal and rescan of a PCIe
NVMe device using sysfs commands where is_added flag was observed as zero
instead of one while removing device and proc,sys entries are not cleared.
This causes issue in later device addition with warning message
"proc_dir_entry" already registered.
Debugging revealed a race condition between the PCI core setting the
is_added bit in pci_bus_add_device() and the NVMe driver reset work-queue
setting the is_busmaster bit in pci_set_master(). As these fields are not
handled atomically, that clears the is_added bit.
Move the is_added bit to a separate private flag variable and use atomic
functions to set and retrieve the device addition state. This avoids the
race because is_added no longer shares a memory location with is_busmaster.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200283
Signed-off-by: Hari Vyas <hari.vyas@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
This patch detaches the preemptirq tracepoints from the tracers and
keeps it separate.
Advantages:
* Lockdep and irqsoff event can now run in parallel since they no longer
have their own calls.
* This unifies the usecase of adding hooks to an irqsoff and irqson
event, and a preemptoff and preempton event.
3 users of the events exist:
- Lockdep
- irqsoff and preemptoff tracers
- irqs and preempt trace events
The unification cleans up several ifdefs and makes the code in preempt
tracer and irqsoff tracers simpler. It gets rid of all the horrific
ifdeferry around PROVE_LOCKING and makes configuration of the different
users of the tracepoints more easy and understandable. It also gets rid
of the time_* function calls from the lockdep hooks used to call into
the preemptirq tracer which is not needed anymore. The negative delta in
lines of code in this patch is quite large too.
In the patch we introduce a new CONFIG option PREEMPTIRQ_TRACEPOINTS
as a single point for registering probes onto the tracepoints. With
this,
the web of config options for preempt/irq toggle tracepoints and its
users becomes:
PREEMPT_TRACER PREEMPTIRQ_EVENTS IRQSOFF_TRACER PROVE_LOCKING
| | \ | |
\ (selects) / \ \ (selects) /
TRACE_PREEMPT_TOGGLE ----> TRACE_IRQFLAGS
\ /
\ (depends on) /
PREEMPTIRQ_TRACEPOINTS
Other than the performance tests mentioned in the previous patch, I also
ran the locking API test suite. I verified that all tests cases are
passing.
I also injected issues by not registering lockdep probes onto the
tracepoints and I see failures to confirm that the probes are indeed
working.
This series + lockdep probes not registered (just to inject errors):
[ 0.000000] hard-irqs-on + irq-safe-A/21: ok | ok | ok |
[ 0.000000] soft-irqs-on + irq-safe-A/21: ok | ok | ok |
[ 0.000000] sirq-safe-A => hirqs-on/12:FAILED|FAILED| ok |
[ 0.000000] sirq-safe-A => hirqs-on/21:FAILED|FAILED| ok |
[ 0.000000] hard-safe-A + irqs-on/12:FAILED|FAILED| ok |
[ 0.000000] soft-safe-A + irqs-on/12:FAILED|FAILED| ok |
[ 0.000000] hard-safe-A + irqs-on/21:FAILED|FAILED| ok |
[ 0.000000] soft-safe-A + irqs-on/21:FAILED|FAILED| ok |
[ 0.000000] hard-safe-A + unsafe-B #1/123: ok | ok | ok |
[ 0.000000] soft-safe-A + unsafe-B #1/123: ok | ok | ok |
With this series + lockdep probes registered, all locking tests pass:
[ 0.000000] hard-irqs-on + irq-safe-A/21: ok | ok | ok |
[ 0.000000] soft-irqs-on + irq-safe-A/21: ok | ok | ok |
[ 0.000000] sirq-safe-A => hirqs-on/12: ok | ok | ok |
[ 0.000000] sirq-safe-A => hirqs-on/21: ok | ok | ok |
[ 0.000000] hard-safe-A + irqs-on/12: ok | ok | ok |
[ 0.000000] soft-safe-A + irqs-on/12: ok | ok | ok |
[ 0.000000] hard-safe-A + irqs-on/21: ok | ok | ok |
[ 0.000000] soft-safe-A + irqs-on/21: ok | ok | ok |
[ 0.000000] hard-safe-A + unsafe-B #1/123: ok | ok | ok |
[ 0.000000] soft-safe-A + unsafe-B #1/123: ok | ok | ok |
Link: http://lkml.kernel.org/r/20180730222423.196630-4-joel@joelfernandes.org
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Thee USB Audio Class 3 (UAC3) introduces Power Domains as a new
feature to let a host turn individual parts of an audio function
to different power states via USB requests. This lets the device
get to know a bit amore about what the host is up to in order to
optimize power consumption efficiently.
The Power Domains are optional for UAC3 configuration but all
UAC3 devices shall include at least one BADD configuration where
the support for Power Domains is compulsory.
This patch adds a set of features/helpers to parse these power
domains and change their status.
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The macro WARN_CONSOLE_UNLOCKED prints a warning when a thread enters
the console's critical section without having acquired the console
lock. The console lock can be ignored when debugging the console using
printk, but this makes WARN_CONSOLE_UNLOCKED generate unnecessary
warnings.
The variable ignore_console_lock_warning temporarily disables
WARN_CONSOLE_UNLOCKED. Developers interested in debugging the console's
critical sections should increment it before entering the CS and
decrement it after leaving the CS. Setting ignore_console_lock_warning
is only for debugging. Regular operation should not manipulate it.
Acknoledgements: This patch is based on an earlier version by Steven
Rostedt. The use of atomic increment/decrement was suggested by Petr
Mladek.
Link: http://lkml.kernel.org/r/717e6337-e7a6-7a92-1c1b-8929a25696b5@suse.de
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
[b.zolnierkie: use <linux/atomic.h>]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Don't load the via-pmu68k driver on early PowerBooks. The M50753 PMU
device found in those models was never supported by this driver.
Attempting to load the driver usually causes a boot hang.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Thanks to the migration of all drivers to use nand_scan() and the
related nand_controller_ops, we can now allocate data during the
detection phase. Let's do it first for the NAND model parameter which
is allocated in nand_detect().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Both nand_scan_ident() and nand_scan_tail() helpers used to be called
directly from controller drivers that needed to tweak some ECC-related
parameters before nand_scan_tail(). This separation prevented dynamic
allocations during the phase of NAND identification, which was
inconvenient.
All controller drivers have been moved to use nand_scan(), in
conjunction with the chip->ecc.[attach|detach]_chip() hooks that
actually do the required tweaking sequence between both ident/tail
calls, allowing programmers to use dynamic allocation as they need all
across the scanning sequence.
Declare nand_scan_[ident|tail]() statically now.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
In order to remove the limitation that forbids dynamic allocation in
nand_scan_ident(), we must create a path that will be the same for all
controller drivers. The idea is to use nand_scan() instead of the widely
used nand_scan_ident()/nand_scan_tail() couple. In order to achieve
this, controller drivers will need to adjust some parameters between
these two functions depending on the NAND chip wired on them.
This takes the form of two new hooks (->{attach,detach}_chip()) that are
placed in a new nand_controller_ops structure, which is then attached
to the nand_controller object at driver initialization time.
->attach_chip() is called between nand_scan_ident() and
nand_scan_tail(), and ->detach_chip() is called in the error path of
nand_scan() and in nand_cleanup().
Note that some NAND controller drivers don't have a dedicated
nand_controller object and instead rely on the default/dummy one
embedded in nand_chip. If you're in this case and still want to
initialize the controller ops, you'll have to manipulate
chip->dummy_controller directly.
Last but not least, it's worth mentioning that we plan to move some of
the controller related hooks placed in nand_chip into
nand_controller_ops to make the separation between NAND chip and NAND
controller methods clearer.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
In the raw NAND core, a NAND chip is described by a nand_chip structure,
while a NAND controller is described with a nand_hw_control structure
which is not very meaningful.
Rename this structure nand_controller.
As the structure gets renamed, it is logical to also rename the core
function initializing it from nand_hw_control_init() to
nand_controller_init().
Lastly, the 'hwcontrol' entry of the nand_chip structure is not
meaningful neither while it has the role of fallback when no controller
structure is provided by the driver (the controller driver is dumb and
can only control a single chip). Thus, it is renamed dummy_controller.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
A report from Colin Ian King pointed a CoverityScan issue where error
values on these helpers where not checked in the drivers. These
helpers can error out only in case of a software bug in driver code,
not because of a runtime/hardware error. Hence, let's WARN_ON() in this
case and return 0 which is harmless anyway.
Fixes: 8878b126df ("mtd: nand: add ->exec_op() implementation")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
bpf_get_socket_cookie() helper can be used to identify skb that
correspond to the same socket.
Though socket cookie can be useful in many other use-cases where socket is
available in program context. Specifically BPF_PROG_TYPE_CGROUP_SOCK_ADDR
and BPF_PROG_TYPE_SOCK_OPS programs can benefit from it so that one of
them can augment a value in a map prepared earlier by other program for
the same socket.
The patch adds support to call bpf_get_socket_cookie() from
BPF_PROG_TYPE_CGROUP_SOCK_ADDR and BPF_PROG_TYPE_SOCK_OPS.
It doesn't introduce new helpers. Instead it reuses same helper name
bpf_get_socket_cookie() but adds support to this helper to accept
`struct bpf_sock_addr` and `struct bpf_sock_ops`.
Documentation in bpf.h is changed in a way that should not break
automatic generation of markdown.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The seg6local LWT provides the End.DT6 action, which allows to
decapsulate an outer IPv6 header containing a Segment Routing Header
(SRH), full specification is available here:
https://tools.ietf.org/html/draft-filsfils-spring-srv6-network-programming-05
This patch adds this action now to the seg6local BPF
interface. Since it is not mandatory that the inner IPv6 header also
contains a SRH, seg6_bpf_srh_state has been extended with a pointer to
a possible SRH of the outermost IPv6 header. This helps assessing if the
validation must be triggered or not, and avoids some calls to
ipv6_find_hdr.
v3: s/1/true, s/0/false for boolean values
v2: - changed true/false -> 1/0
- preempt_enable no longer called in first conditional block
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This just adds a helper function to check if a device is configured and it
converts the target users to use it. The next patch will add a backend
module user so those types of modules do not have to know the lio core
details.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Return bool for following internal and inline functions as their
underlying APIs return bool too.
1. cma_zero_addr()
2. cma_loopback_addr()
3. cma_any_addr()
4. ib_addr_any()
5. ib_addr_loopback()
While we are touching cma_loopback_addr(), remove extra white spaces
in it.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Constify several pointers such as path_rec, ib_cm_event and listen_id
pointers in several functions.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Following APIs are not supposed to modify addr or dest_addr contents.
Therefore make those function argument const for better code
readability.
1. rdma_resolve_ip()
2. rdma_addr_size()
3. rdma_resolve_addr()
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This clearly indicates that the input is a bitwise combination of values
in an enum, and identifies which enum contains the definition of the bits.
Special accessors are provided that handle the mandatory validation of the
allowed bits and enforce the correct type for bitwise flags.
If we had introduced this at the start then the kabi would have uniformly
used u64 data to pass flags, however today there is a mixture of u64 and
u32 flags. All places are converted to accept both sizes and the accessor
fixes it. This allows all existing flags to grow to u64 in future without
any hassle.
Finally all flags are, by definition, optional. If flags are not passed
the accessor does not fail, but provides a value of zero.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Since neither ib_post_send() nor ib_post_recv() modify the data structure
their second argument points at, declare that argument const. This change
makes it necessary to declare the 'bad_wr' argument const too and also to
modify all ULPs that call ib_post_send(), ib_post_recv() or
ib_post_srq_recv(). This patch does not change any functionality but makes
it possible for the compiler to verify whether the
ib_post_(send|recv|srq_recv) really do not modify the posted work request.
To make this possible, only one cast had to be introduce that casts away
constness, namely in rpcrdma_post_recvs(). The only way I can think of to
avoid that cast is to introduce an additional loop in that function or to
change the data type of bad_wr from struct ib_recv_wr ** into int
(an index that refers to an element in the work request list). However,
both approaches would require even more extensive changes than this
patch.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When posting a send work request, the work request that is posted is not
modified by any of the RDMA drivers. Make this explicit by constifying
most ib_send_wr pointers in RDMA transport drivers.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In recent tests with IRQ on/off tracepoints, a large performance
overhead ~10% is noticed when running hackbench. This is root caused to
calls to rcu_irq_enter_irqson and rcu_irq_exit_irqson from the
tracepoint code. Following a long discussion on the list [1] about this,
we concluded that srcu is a better alternative for use during rcu idle.
Although it does involve extra barriers, its lighter than the sched-rcu
version which has to do additional RCU calls to notify RCU idle about
entry into RCU sections.
In this patch, we change the underlying implementation of the
trace_*_rcuidle API to use SRCU. This has shown to improve performance
alot for the high frequency irq enable/disable tracepoints.
Test: Tested idle and preempt/irq tracepoints.
Here are some performance numbers:
With a run of the following 30 times on a single core x86 Qemu instance
with 1GB memory:
hackbench -g 4 -f 2 -l 3000
Completion times in seconds. CONFIG_PROVE_LOCKING=y.
No patches (without this series)
Mean: 3.048
Median: 3.025
Std Dev: 0.064
With Lockdep using irq tracepoints with RCU implementation:
Mean: 3.451 (-11.66 %)
Median: 3.447 (-12.22%)
Std Dev: 0.049
With Lockdep using irq tracepoints with SRCU implementation (this series):
Mean: 3.020 (I would consider the improvement against the "without
this series" case as just noise).
Median: 3.013
Std Dev: 0.033
[1] https://patchwork.kernel.org/patch/10344297/
[remove rcu_read_lock_sched_notrace as its the equivalent of
preempt_disable_notrace and is unnecessary to call in tracepoint code]
Link: http://lkml.kernel.org/r/20180730222423.196630-3-joel@joelfernandes.org
Cleaned-up-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
[ Simplified WARN_ON_ONCE() ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
KVM: s390: initial host large page support
- must be enabled via module parameter hpage=1
- cannot be used together with nested
- does support migration
- does support hugetlbfs
- no THP yet
General KVM huge page support on s390 has to be enabled via the
kvm.hpage module parameter. Either nested or hpage can be enabled, as
we currently do not support vSIE for huge backed guests. Once the vSIE
support is added we will either drop the parameter or enable it as
default.
For a guest the feature has to be enabled through the new
KVM_CAP_S390_HPAGE_1M capability and the hpage module
parameter. Enabling it means that cmm can't be enabled for the vm and
disables pfmf and storage key interpretation.
This is due to the fact that in some cases, in upcoming patches, we
have to split huge pages in the guest mapping to be able to set more
granular memory protection on 4k pages. These split pages have fake
page tables that are not visible to the Linux memory management which
subsequently will not manage its PGSTEs, while the SIE will. Disabling
these features lets us manage PGSTE data in a consistent matter and
solve that problem.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
There are a number of other ioctls that aren't used anywhere
inside the Kernel tree.
Get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are a number of other ioctls that aren't used anywhere
inside the Kernel tree.
Get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Pull locking fixes from Ingo Molnar:
"A paravirt UP-patching fix, and an I2C MUX driver lockdep warning fix"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/pvqspinlock/x86: Use LOCK_PREFIX in __pv_queued_spin_unlock() assembly code
i2c/mux, locking/core: Annotate the nested rt_mutex usage
locking/rtmutex: Allow specifying a subclass for nested locking
This turns rpc_auth_create_args into a const as it gets passed through the
auth stack.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
This is similar TC_ACT_REDIRECT, but with a slightly different
semantic:
- on ingress the mirred skbs are passed to the target device
network stack without any additional check not scrubbing.
- the rcu-protected stats provided via the tcf_result struct
are updated on error conditions.
This new tcfa_action value is not exposed to the user-space
and can be used only internally by clsact.
v1 -> v2: do not touch TC_ACT_REDIRECT code path, introduce
a new action type instead
v2 -> v3:
- rename the new action value TC_ACT_REINJECT, update the
helper accordingly
- take care of uncloned reinjected packets in XDP generic
hook
v3 -> v4:
- renamed again the new action value (JiriP)
v4 -> v5:
- fix build error with !NET_CLS_ACT (kbuild bot)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each lockless action currently does its own RCU locking in ->act().
This allows using plain RCU accessor, even if the context
is really RCU BH.
This change drops the per action RCU lock, replace the accessors
with the _bh variant, cleans up a bit the surrounding code and
documents the RCU status in the relevant header.
No functional nor performance change is intended.
The goal of this patch is clarifying that the RCU critical section
used by the tc actions extends up to the classifier's caller.
v1 -> v2:
- preserve rcu lock in act_bpf: it's needed by eBPF helpers,
as pointed out by Daniel
v3 -> v4:
- fixed some typos in the commit message (JiriP)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when initializing an action, the user-space can specify
and use arbitrary values for the tcfa_action field. If the value
is unknown by the kernel, is implicitly threaded as TC_ACT_UNSPEC.
This change explicitly checks for unknown values at action creation
time, and explicitly convert them to TC_ACT_UNSPEC. No functional
changes are introduced, but this will allow introducing tcfa_action
values not exposed to user-space in a later patch.
Note: we can't use the above to hide TC_ACT_REDIRECT from user-space,
as the latter is already part of uAPI.
v3 -> v4:
- use an helper to check for action validity (JiriP)
- emit an extack for invalid actions (JiriP)
v4 -> v5:
- keep messages on a single line, drop net_warn (Marcelo)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fold it into the only caller to make the code simpler and easier to read.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in hiding this logic in a helper. Also remove the
useless events != 0 check and only busy loop once we know we actually
have a poll method.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
For any open socket file descriptor sock->sk->sk_wq->wait will always
point to sock->wq->wait. That means we can do the shorter dereference
and removal a NULL check and don't have to not worry about any RCU
protection.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wait_address argument is always directly derived from the filp
argument, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently these functions are implemented in the scsi layer, but their
actual place should be the block layer since T10-PI is a general data
integrity feature that is used in the nvme protocol as well. Also, use
the tuple size from the integrity profile since it may vary between
integrity types.
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently this function is implemented in the scsi layer, but it's
actual place should be the block layer since T10-PI is a general
data integrity feature that is used in the nvme protocol as well.
Suggested-by: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
