Pull IIO driver fixes from Greg KH:
"Here are some old IIO driver fixes that were sitting in my tree for a
few weeks. Sorry about not getting them to you sooner. They fix a
number of small IIO driver issues that have been reported.
All of these have been in linux-next for a while with no reported
problems"
* tag 'staging-4.17-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: adc: select buffer for at91-sama5d2_adc
iio: hid-sensor-trigger: Fix sometimes not powering up the sensor after resume
iio: adc: at91-sama5d2_adc: fix channel configuration for differential channels
iio:kfifo_buf: check for uint overflow
iio:buffer: make length types match kfifo types
iio: adc: stm32-dfsdm: fix sample rate for div2 spi clock
iio: adc: stm32-dfsdm: fix successive oversampling settings
iio: ad7793: implement IIO_CHAN_INFO_SAMP_FREQ
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree, the most relevant things in this batch are:
1) Compile masquerade infrastructure into NAT module, from Florian Westphal.
Same thing with the redirection support.
2) Abort transaction if early initialization of the commit phase fails.
Also from Florian.
3) Get rid of synchronize_rcu() by using rule array in nf_tables, from
Florian.
4) Abort nf_tables batch if fatal signal is pending, from Florian.
5) Use .call_rcu nfnetlink from nf_tables to make dumps fully lockless.
From Florian Westphal.
6) Support to match transparent sockets from nf_tables, from Máté Eckl.
7) Audit support for nf_tables, from Phil Sutter.
8) Validate chain dependencies from commit phase, fall back to fine grain
validation only in case of errors.
9) Attach dst to skbuff from netfilter flowtable packet path, from
Jason A. Donenfeld.
10) Use artificial maximum attribute cap to remove VLA from nfnetlink.
Patch from Kees Cook.
11) Add extension to allow to forward packets through neighbour layer.
12) Add IPv6 conntrack helper support to IPVS, from Julian Anastasov.
13) Add IPv6 FTP conntrack support to IPVS, from Julian Anastasov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
get_hp_hw_control_from_firmware() is a trivial wrapper around
acpi_get_hp_hw_control_from_firmware(), probably intended to be generic in
case other firmware needed similar OS/platform negotiation.
Remove get_hp_hw_control_from_firmware() and call
acpi_get_hp_hw_control_from_firmware() directly. Add a stub for
acpi_get_hp_hw_control_from_firmware() for the non-ACPI case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The SHPC driver now must be builtin (it cannot be a module). If it is
present, request SHPC control immediately when adding the ACPI host bridge.
This is similar to how we handle native PCIe hotplug via pciehp.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Previously pciehp_is_native() returned true for any PCI device in a
hierarchy where _OSC says we can use pciehp. This is incorrect because
bridges without PCI_EXP_SLTCAP_HPC capability should be managed by acpiphp
instead.
Improve pciehp_is_native() to return true only when PCI_EXP_SLTCAP_HPC is
set and the pciehp driver is present. In any other case return false
to let acpiphp handle those.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: remove NULL pointer check]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rename host->native_hotplug to host->native_pcie_hotplug to make room for a
similar flag for SHPC hotplug.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We only have two users of the debug_init hook, and we recently stopped
caring about the return value from that op. Finish that off by changing
the clk_op to return void instead of int because it doesn't matter if
debugfs fails or not.
Cc: Eric Anholt <eric@anholt.net>
Cc: David Lechner <david@lechnology.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Associates a counters with a flow when IB_FLOW_SPEC_ACTION_COUNT is part
of the flow specifications.
The counters user space placements of location and description (index,
description) pairs are passed as private data of the counters flow
specification.
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This function is only used by the iomap code, depends on being called
from it, and will soon stop poking into buffer head internals.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
This adds a simple iomap-based implementation of the legacy ->bmap
interface. Note that we can't easily add checks for rt or reflink
files, so these will have to remain in the callers. This interface
just needs to die..
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Just define a range of fs specific flags and use that in gfs2 instead of
exposing this internal flag globally.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Inline data is fundamentally different from our normal mapped case in that
it doesn't even have a block address. So instead of having a flag for it
it should be an entirely separate iomap range type.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
For the upcoming removal of buffer heads in XFS we need to keep track of
the number of outstanding writeback requests per page. For this we need
to know if bio_add_page merged a region with the previous bvec or not.
Instead of adding additional arguments this refactors bio_add_page to
be implemented using three lower level helpers which users like XFS can
use directly if they care about the merge decisions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The kvm struct has been bloating. For example, it's tens of kilo-bytes
for x86, which turns out to be a large amount of memory to allocate
contiguously via kzalloc. Thus, this patch does the following:
1. Uses architecture-specific routines to allocate the kvm struct via
vzalloc for x86.
2. Switches arm to __KVM_HAVE_ARCH_VM_ALLOC so that it can use vzalloc
when has_vhe() is true.
Other architectures continue to default to kalloc, as they have a
dependency on kalloc or have a small-enough struct kvm.
Signed-off-by: Marc Orr <marcorr@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use new return type vm_fault_t for fault handler. For
now, this is just documenting that the function returns
a VM_FAULT value rather than an errno. Once all instances
are converted, vm_fault_t will become a distinct type.
commit 1c8f422059 ("mm: change return type to vm_fault_t")
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All callers of zap_vma_ptes() are not interested in the return value of
that function, so let's simplify its interface and drop the return
value.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the namespace is unregistered before the LightNVM target is removed
(e.g., on hot unplug) it is too late for the target to store any metadata
on the device - any attempt to write to the device will fail. In this
case, pass on a "gracefull teardown" flag to the target to let it know
when this happens.
In the case of pblk, we pad the open line (close all open chunks) to
improve data retention. In the event of an ungraceful shutdown, avoid
this part and just clean up.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull NVMe changes from Christoph:
"Below is another set of NVMe updates for 4.18. Besides the usual bug
fixes this includes more feature completness in terms of AEN and log
page handling on the target."
* 'nvme-4.18' of git://git.infradead.org/nvme:
nvme: use the changed namespaces list log to clear ns data changed AENs
nvme: mark nvme_queue_scan static
nvme: submit AEN event configuration on startup
nvmet: mask pending AENs
nvmet: add AEN configuration support
nvmet: implement the changed namespaces log
nvmet: split log page implementation
nvmet: add a new nvmet_zero_sgl helper
nvme.h: add AEN configuration symbols
nvme.h: add the changed namespace list log
nvme.h: untangle AEN notice definitions
nvmet: fix error return code in nvmet_file_ns_enable()
nvmet: fix a typo in nvmet_file_ns_enable()
nvme-fabrics: allow internal passthrough command on deleting controllers
nvme-loop: add support for multiple ports
nvme-pci: simplify __nvme_submit_cmd
nvme-pci: Rate limit the nvme timeout warnings
nvme: allow duplicate controller if prior controller being deleted
The NAND sub-layers are likely to need the MTD_OPS_XXX mode information
in order to decide if they should enable/disable ECC or how they should
place the OOB bytes in the provided OOB buffer.
Add a field to nand_page_io_req to pass this information.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de>
The following ruleset:
add table ip filter
add chain ip filter input { type filter hook input priority 4; }
add chain ip filter ap
add rule ip filter input jump ap
add rule ip filter ap masquerade
results in a panic, because the masquerade extension should be rejected
from the filter chain. The existing validation is missing a chain
dependency check when the rule is added to the non-base chain.
This patch fixes the problem by walking down the rules from the
basechains, searching for either immediate or lookup expressions, then
jumping to non-base chains and again walking down the rules to perform
the expression validation, so we make sure the full ruleset graph is
validated. This is done only once from the commit phase, in case of
problem, we abort the transaction and perform fine grain validation for
error reporting. This patch requires 003087911a ("netfilter:
nfnetlink: allow commit to fail") to achieve this behaviour.
This patch also adds a cleanup callback to nfnl batch interface to reset
the validate state from the exit path.
As a result of this patch, nf_tables_check_loops() doesn't use
->validate to check for loops, instead it just checks for immediate
expressions.
Reported-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This adds wrappers for the __builtin overflow checkers present in gcc
5.1+ as well as fallback implementations for earlier compilers. It's not
that easy to implement the fully generic __builtin_X_overflow(T1 a, T2
b, T3 *d) in macros, so the fallback code assumes that T1, T2 and T3 are
the same. We obviously don't want the wrappers to have different
semantics depending on $GCC_VERSION, so we also insist on that even when
using the builtins.
There are a few problems with the 'a+b < a' idiom for checking for
overflow: For signed types, it relies on undefined behaviour and is
not actually complete (it doesn't check underflow;
e.g. INT_MIN+INT_MIN == 0 isn't caught). Due to type promotion it
is wrong for all types (signed and unsigned) narrower than
int. Similarly, when a and b does not have the same type, there are
subtle cases like
u32 a;
if (a + sizeof(foo) < a)
return -EOVERFLOW;
a += sizeof(foo);
where the test is always false on 64 bit platforms. Add to that that it
is not always possible to determine the types involved at a glance.
The new overflow.h is somewhat bulky, but that's mostly a result of
trying to be type-generic, complete (e.g. catching not only overflow
but also signed underflow) and not relying on undefined behaviour.
Linus is of course right [1] that for unsigned subtraction a-b, the
right way to check for overflow (underflow) is "b > a" and not
"__builtin_sub_overflow(a, b, &d)", but that's just one out of six cases
covered here, and included mostly for completeness.
So is it worth it? I think it is, if nothing else for the documentation
value of seeing
if (check_add_overflow(a, b, &d))
return -EGOAWAY;
do_stuff_with(d);
instead of the open-coded (and possibly wrong and/or incomplete and/or
UBsan-tickling)
if (a+b < a)
return -EGOAWAY;
do_stuff_with(a+b);
While gcc does recognize the 'a+b < a' idiom for testing unsigned add
overflow, it doesn't do nearly as good for unsigned multiplication
(there's also no single well-established idiom). So using
check_mul_overflow in kcalloc and friends may also make gcc generate
slightly better code.
[1] https://lkml.org/lkml/2015/11/2/658
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Kees Cook <keescook@chromium.org>
The FPGA queue pair (QP) event fires whenever a QP on the FPGA
transitions to the error state.
At this stage, this event is unrecoverable, it may become recoverable
in the future.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Adi Nissim <adin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Temperature warning event is sent by FW to indicate high temperature
as detected by one of the sensors on the board.
Add handling of this event by writing the numbers of the alert sensors
to the kernel log.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Adi Nissim <adin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the LAYOUTGET on OPEN can be sent without prior inode information,
existing methods to prevent LAYOUTGET from being sent while processing
CB_LAYOUTRECALL don't work. Track if a recall occurred while LAYOUTGET
was being sent, and if so ignore the results.
Signed-off-by: Fred Isaman <fred.isaman@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
This will be needed to seperate return value of OPEN and LAYOUTGET
when they are combined into a single RPC.
Signed-off-by: Fred Isaman <fred.isaman@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Ensure that we pass down the inode of the file being deleted so
that we can return any delegation being held.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Rather than doing this in the generic NFS client code. Let's put this
with the other v4 stuff so it's all in one place.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
This doesn't really need to be in the generic NFS client code, and I
think it makes more sense to keep the v4 code in one place.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
list_for_each_entry_from_rcu() is an RCU version of
list_for_each_entry_from(). It walks a linked list under rcu
protection, from a given start point.
It is similar to list_for_each_entry_continue_rcu() but starts *at*
the given position rather than *after* it.
Naturally, the start point must be known to be in the list.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
This patch adds driver changes for capturing the link change count in
ethtool statistics display.
Please consider applying this to "net-next".
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop including the event type in the definitions for the notice type.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
In order for the kernel to protect itself, let's call the SSBD mitigation
implemented by the higher exception level (either hypervisor or firmware)
on each transition between userspace and kernel.
We must take the PSCI conduit into account in order to target the
right exception level, hence the introduction of a runtime patching
callback.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We've so far used the PSCI return codes for SMCCC because they
were extremely similar. But with the new ARM DEN 0070A specification,
"NOT_REQUIRED" (-2) is clashing with PSCI's "PSCI_RET_INVALID_PARAMS".
Let's bite the bullet and add SMCCC specific return codes. Users
can be repainted as and when required.
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The function return values are confusing with the way the function is
named. We expect a true or false return value but it actually returns
0/-errno. This makes the code very confusing. Changing the return values
to return a bool where if DAX is supported then return true and no DAX
support returns false.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Change bdev_dax_supported so it takes a bdev parameter. This enables
multi-device filesystems like xfs to check that a dax device can work for
the particular filesystem. Once that's in place, actually fix all the
parts of XFS where we need to be able to distinguish between datadev and
rtdev.
This patch fixes the problem where we screw up the dax support checking
in xfs if the datadev and rtdev have different dax capabilities.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
[rez: Re-added __bdev_dax_supported() for !CONFIG_FS_DAX cases]
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
This is the per-I/O equivalent of the ioprio_set system call.
When IOCB_FLAG_IOPRIO is set on the iocb aio_flags field, then we set the
newly added kiocb ki_ioprio field to the value in the iocb aio_reqprio field.
This patch depends on block: add ioprio_check_cap function.
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In order to avoid kiocb bloat for per command iopriority support, rw_hint
is converted from enum to a u16. Added a guard around ki_hint assignment.
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Aio per command iopriority support introduces a second interface between
userland and the kernel capable of passing iopriority. The aio interface also
needs the ability to verify that the submitting context has sufficient
privileges to submit IOPRIO_RT commands. This patch creates the
ioprio_check_cap function to be used by the ioprio_set system call and also by
the aio interface.
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
