Convert the {read/write}_counter APIs to handle 64bit values
to enable supporting chained event counters. The backends still
use 32bit values and we pass them 32bit values only. So in effect
there are no functional changes.
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Each PMU defines their max_period of the counter as the maximum
value that can be counted. Since all the PMU backends support
32bit counters by default, let us remove the redundant field.
No functional changes.
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Deferred probe will currently wait forever on dependent devices to probe,
but sometimes a driver will never exist. It's also not always critical for
a driver to exist. Platforms can rely on default configuration from the
bootloader or reset defaults for things such as pinctrl and power domains.
This is often the case with initial platform support until various drivers
get enabled. There's at least 2 scenarios where deferred probe can render
a platform broken. Both involve using a DT which has more devices and
dependencies than the kernel supports. The 1st case is a driver may be
disabled in the kernel config. The 2nd case is the kernel version may
simply not have the dependent driver. This can happen if using a newer DT
(provided by firmware perhaps) with a stable kernel version. Deferred
probe issues can be difficult to debug especially if the console has
dependencies or userspace fails to boot to a shell.
There are also cases like IOMMUs where only built-in drivers are
supported, so deferring probe after initcalls is not needed. The IOMMU
subsystem implemented its own mechanism to handle this using OF_DECLARE
linker sections.
This commit adds makes ending deferred probe conditional on initcalls
being completed or a debug timeout. Subsystems or drivers may opt-in by
calling driver_deferred_probe_check_init_done() instead of
unconditionally returning -EPROBE_DEFER. They may use additional
information from DT or kernel's config to decide whether to continue to
defer probe or not.
The timeout mechanism is intended for debug purposes and WARNs loudly.
The remaining deferred probe pending list will also be dumped after the
timeout. Not that this timeout won't work for the console which needs
to be enabled before userspace starts. However, if the console's
dependencies are resolved, then the kernel log will be printed (as
opposed to no output).
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All users now register platform devices using the ti-aemif driver.
Remove the handcrafted aemif API.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add support for RTC mode to low level suspend code. This includes
providing the rtc base address for the assembly code to configuring the
PMIC_PWR_EN line late in suspend to enter RTC+DDR mode.
Note: This patch also fold in left out space parameter for
am33xx_emif_sram_table and am43xx_emif_sram_table
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add an argument to the sleep33xx and sleep43xx code to allow us to set
flags to determine which portions of the code get called in order to use
the same code for multiple power saving modes. This patch allows us to
decide whether or not we flush and disable caches, save EMIF context,
put the memory into self refresh and disable the EMIF, and/or invoke
the wkup_m3 when entering into WFI.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The dra76x MCAN generic interconnect module has a its own
format for the bits in the control registers.
Therefore add a new module type, new regbits and new capabilities
specific to the MCAN module.
Acked-by: Rob Herring <robh@kernel.org>
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
More features for 4.19:
- Use core pcie functionality rather than duplicating our own for pcie
gens and lanes
- Scheduler function naming cleanups
- More documentation
- Reworked DC/Powerplay interfaces to improve power savings
- Initial stutter mode support for RV (power feature)
- Vega12 powerplay updates
- GFXOFF fixes
- Misc fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705221447.2807-1-alexander.deucher@amd.com
Pull HID fixes from Jiri Kosina:
- spectrev1 pattern fix in hiddev from Gustavo A. R. Silva
- bounds check fix for hid-debug from Daniel Rosenberg
- regression fix for HID autobinding from Benjamin Tissoires
- removal of excessive logging from i2c-hid driver from Jason Andryuk
- fix specific to 2nd generation of Wacom Intuos devices from Jason
Gerecke
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hiddev: fix potential Spectre v1
HID: i2c-hid: Fix "incomplete report" noise
HID: wacom: Correct touch maximum XY of 2nd-gen Intuos
HID: debug: check length before copy_to_user()
HID: core: allow concurrent registration of drivers
nf_hook() can free the skb, so we need to remove it from the list before
calling, and add passed skbs to a sublist afterwards.
Fixes: 17266ee939 ("net: ipv4: listified version of ip_rcv")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For most of these calls we can just pass NULL through to the fallback
function as the sb_dev. The only cases where we cannot are the cases where
we might be dealing with either an upper device or a driver that would
have configured things to support an sb_dev itself.
The only driver that has any significant change in this patch set should be
ixgbe as we can drop the redundant functionality that existed in both the
ndo_select_queue function and the fallback function that was passed through
to us.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes it so that instead of passing a void pointer as the
accel_priv we instead pass a net_device pointer as sb_dev. Making this
change allows us to pass the subordinate device through to the fallback
function eventually so that we can keep the actual code in the
ndo_select_queue call as focused on possible on the exception cases.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a generic version of the ndo_select_queue functions for
either returning 0 or selecting a queue based on the processor ID. This is
generally meant to just reduce the number of functions we have to change
in the future when we have to deal with ndo_select_queue changes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can support the concept of subordinate
device traffic classes to the core networking code. In doing this we can
start pulling out the driver specific bits needed to support selecting a
queue based on an upper device.
The solution at is currently stands is only partially implemented. I have
the start of some XPS bits in here, but I would still need to allow for
configuration of the XPS maps on the queues reserved for the subordinate
devices. For now I am using the reference to the sb_dev XPS map as just a
way to skip the lookup of the lower device XPS map for now as that would
result in the wrong queue being picked.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to provide the basic tools needed to allow us to create
subordinate device traffic classes. The general idea here is to allow
subdividing the queues of a device into queue groups accessible through an
upper device such as a macvlan.
The idea here is to enforce the idea that an upper device has to be a
single queue device, ideally with IFF_NO_QUQUE set. With that being the
case we can pretty much guarantee that the tc_to_txq mappings and XPS maps
for the upper device are unused. As such we could reuse those in order to
support subdividing the lower device and distributing those queues between
the subordinate devices.
In order to distinguish between a regular set of traffic classes and if a
device is carrying subordinate traffic classes I changed num_tc from a u8
to a s16 value and use the negative values to represent the subordinate
pool values. So starting at -1 and running to -32768 we can encode those as
pool values, and the existing values of 0 to 15 can be maintained.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
'cmd_pause' DMA channel capability means that respective DMA engine
supports both pausing and resuming given DMA channel. However, in some
cases it is important to know if DMA channel can be paused without the
need to resume it. This is a typical requirement for proper residue
reading on transfer timeout in UART drivers. There are also some DMA
engines with limited hardware, which doesn't really support resuming.
Reporting pause and resume capabilities separately allows UART drivers to
properly check for the really required capabilities and operate in DMA
mode also in systems with limited DMA hardware. On the other hand drivers,
which rely on full channel suspend/resume support, should now check for
both 'pause' and 'resume' features.
Existing clients of dma_get_slave_caps() have been checked and the only
driver which rely on proper channel resuming is soc-generic-dmaengine-pcm
driver, which has been updated to check the newly added capability.
Existing 'cmd_pause' now only indicates that DMA engine support pausing
given DMA channel.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Current IO controllers for the block layer are less than ideal for our
use case. The io.max controller is great at hard limiting, but it is
not work conserving. This patch introduces io.latency. You provide a
latency target for your group and we monitor the io in short windows to
make sure we are not exceeding those latency targets. This makes use of
the rq-qos infrastructure and works much like the wbt stuff. There are
a few differences from wbt
- It's bio based, so the latency covers the whole block layer in addition to
the actual io.
- We will throttle all IO types that comes in here if we need to.
- We use the mean latency over the 100ms window. This is because writes can
be particularly fast, which could give us a false sense of the impact of
other workloads on our protected workload.
- By default there's no throttling, we set the queue_depth to INT_MAX so that
we can have as many outstanding bio's as we're allowed to. Only at
throttle time do we pay attention to the actual queue depth.
- We backcharge cgroups for root cg issued IO and induce artificial
delays in order to deal with cases like metadata only or swap heavy
workloads.
In testing this has worked out relatively well. Protected workloads
will throttle noisy workloads down to 1 io at time if they are doing
normal IO on their own, or induce up to a 1 second delay per syscall if
they are doing a lot of root issued IO (metadata/swap IO).
Our testing has revolved mostly around our production web servers where
we have hhvm (the web server application) in a protected group and
everything else in another group. We see slightly higher requests per
second (RPS) on the test tier vs the control tier, and much more stable
RPS across all machines in the test tier vs the control tier.
Another test we run is a slow memory allocator in the unprotected group.
Before this would eventually push us into swap and cause the whole box
to die and not recover at all. With these patches we see slight RPS
drops (usually 10-15%) before the memory consumer is properly killed and
things recover within seconds.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blkcg-qos is going to do essentially what wbt does, only on a cgroup
basis. Break out the common code that will be shared between blkcg-qos
and wbt into blk-rq-qos.* so they can both utilize the same
infrastructure.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Memory allocations can induce swapping via kswapd or direct reclaim. If
we are having IO done for us by kswapd and don't actually go into direct
reclaim we may never get scheduled for throttling. So instead check to
see if our cgroup is congested, and if so schedule the throttling.
Before we return to user space the throttling stuff will only throttle
if we actually required it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since IO can be issued from literally anywhere it's almost impossible to
do throttling without having some sort of adverse effect somewhere else
in the system because of locking or other dependencies. The best way to
solve this is to do the throttling when we know we aren't holding any
other kernel resources. Do this by tracking throttling in a per-blkg
basis, and if we require throttling flag the task that it needs to check
before it returns to user space and possibly sleep there.
This is to address the case where a process is doing work that is
generating IO that can't be throttled, whether that is directly with a
lot of REQ_META IO, or indirectly by allocating so much memory that it
is swamping the disk with REQ_SWAP. We can't use task_add_work as we
don't want to induce a memory allocation in the IO path, so simply
saving the request queue in the task and flagging it to do the
notify_resume thing achieves the same result without the overhead of a
memory allocation.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For backcharging we need to know who the page belongs to when swapping
it out. We don't worry about things that do ->rw_page (zram etc) at the
moment, we're only worried about pages that actually go to a block
device.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Just like REQ_META, it's important to know the IO coming down is swap
in order to guard against potential IO priority inversion issues with
cgroups. Add REQ_SWAP and use it for all swap IO, and add it to our
bio_issue_as_root_blkg helper.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk-iolatency has a few stats that it would like to print out, and
instead of adding a bunch of crap to the generic code just provide a
helper so that controllers can add stuff to the stat line if they want
to.
Hide it behind a boot option since it changes the output of io.stat from
normal, and these stats are only interesting to developers.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead of forcing all file systems to get the right context on their
bio's, simply check for REQ_META to see if we need to issue as the root
blkg. We don't want to force all bio's to have the root blkg associated
with them if REQ_META is set, as some controllers (blk-iolatency) need
to know who the originating cgroup is so it can backcharge them for the
work they are doing. This helper will make sure that the controllers do
the proper thing wrt the IO priority and backcharging.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently io.low uses a bi_cg_private to stash its private data for the
blkg, however other blkcg policies may want to use this as well. Since
we can get the private data out of the blkg, move this to bi_blkg in the
bio and make it generic, then we can use bio_associate_blkg() to attach
the blkg to the bio.
Theoretically we could simply replace the bi_css with this since we can
get to all the same information from the blkg, however you have to
lookup the blkg, so for example wbc_init_bio() would have to lookup and
possibly allocate the blkg for the css it was trying to attach to the
bio. This could be problematic and result in us either not attaching
the css at all to the bio, or falling back to the root blkcg if we are
unable to allocate the corresponding blkg.
So for now do this, and in the future if possible we could just replace
the bi_css with bi_blkg and update the helpers to do the correct
translation.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It won't be efficient to dequeue request one by one from sw queue,
but we have to do that when queue is busy for better merge performance.
This patch takes the Exponential Weighted Moving Average(EWMA) to figure
out if queue is busy, then only dequeue request one by one from sw queue
when queue is busy.
Fixes: b347689ffb ("blk-mq-sched: improve dispatching from sw queue")
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Hannes Reinecke <hare@suse.de>
Reported-by: Kashyap Desai <kashyap.desai@broadcom.com>
Tested-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We have to remove synchronize_rcu() from blk_queue_cleanup(),
otherwise long delay can be caused during lun probe. For removing
it, we have to avoid to iterate the set->tag_list in IO path, eg,
blk_mq_sched_restart().
This patch reverts 5b79413946d (Revert "blk-mq: don't handle
TAG_SHARED in restart"). Given we have fixed enough IO hang issue,
and there isn't any reason to restart all queues in one tags any more,
see the following reasons:
1) blk-mq core can deal with shared-tags case well via blk_mq_get_driver_tag(),
which can wake up queues waiting for driver tag.
2) SCSI is a bit special because it may return BLK_STS_RESOURCE if queue,
target or host is ready, but SCSI built-in restart can cover all these well,
see scsi_end_request(), queue will be rerun after any request initiated from
this host/target is completed.
In my test on scsi_debug(8 luns), this patch may improve IOPS by 20% ~ 30%
when running I/O on these 8 luns concurrently.
Fixes: 705cda97ee ("blk-mq: Make it safe to use RCU to iterate over blk_mq_tag_set.tag_list")
Cc: Omar Sandoval <osandov@fb.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Reported-by: Andrew Jones <drjones@redhat.com>
Tested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now hctx->lock is only acquired when adding hctx->dispatch_wait to
one wait queue, but not held when removing it from the wait queue.
IO hang can be observed easily if SCHED RESTART is disabled, that means
now RESTART exits just for fixing the issue in blk_mq_mark_tag_wait().
This patch fixes the issue by introducing hctx->dispatch_wait_lock and
holding it for removing hctx->dispatch_wait in blk_mq_dispatch_wake(),
since we need to avoid acquiring hctx->lock in irq context.
Fixes: eb619fdb2d ("blk-mq: fix issue with shared tag queue re-running")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Tested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Exclude zoned block device members from struct request_queue for
CONFIG_BLK_DEV_ZONED == n. Avoid breaking the build by only building
the code that uses these struct request_queue members if
CONFIG_BLK_DEV_ZONED != n.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Matias Bjorling <mb@lightnvm.io>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since the implementation of blk_queue_nr_zones() is trivial and since
it only has a single caller, inline this function.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Matias Bjorling <mb@lightnvm.io>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove this function since it has no callers. This function was
introduced in commit 6cc77e9cb0 ("block: introduce zoned block
devices zone write locking").
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matias Bjorling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The commit 719f6a7040 ("printk: Use the main logbuf in NMI
when logbuf_lock is available") brought back the possible deadlocks
in printk() and NMI.
The check of logbuf_lock is done only in printk_nmi_enter() to prevent
mixed output. But another CPU might take the lock later, enter NMI, and:
+ Both NMIs might be serialized by yet another lock, for example,
the one in nmi_cpu_backtrace().
+ The other CPU might get stopped in NMI, see smp_send_stop()
in panic().
The only safe solution is to use trylock when storing the message
into the main log-buffer. It might cause reordering when some lines
go to the main lock buffer directly and others are delayed via
the per-CPU buffer. It means that it is not useful in general.
This patch replaces the problematic NMI deferred context with NMI
direct context. It can be used to mark a code that might produce
many messages in NMI and the risk of losing them is more critical
than problems with eventual reordering.
The context is then used when dumping trace buffers on oops. It was
the primary motivation for the original fix. Also the reordering is
even smaller issue there because some traces have their own time stamps.
Finally, nmi_cpu_backtrace() need not longer be serialized because
it will always us the per-CPU buffers again.
Fixes: 719f6a7040 ("printk: Use the main logbuf in NMI when logbuf_lock is available")
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20180627142028.11259-1-pmladek@suse.com
To: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
The pinconf_generic_dump_one() function makes the assumption that
pin_config_group_get() should return -EINVAL and -ENOTSUPP just like
pin_config_get() does. Document that so it's more obvious.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a flag to autoremove the device links on supplier driver
unbind. This obviates the need to explicitly delete the link
in the remove path.
We remove these links only when the supplier's link to its
consumers has gone to DL_STATE_SUPPLIER_UNBIND state.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Suggested-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that we want to add another flag to autoremove the device link
on supplier unbind, it's fair to rename the existing flag from
DL_FLAG_AUTOREMOVE to DL_FLAG_AUTOREMOVE_CONSUMER so that we can
add similar flag for supplier later.
And, while we are touching device.h, fix a doc build warning.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For the multiple PM domain case, let's introduce a new API called
dev_pm_domain_attach_by_name(). This allows a consumer driver to associate
its device with one of its PM domains, by using a name based lookup.
Do note that, currently it's only genpd that supports multiple PM domains
per device, but dev_pm_domain_attach_by_name() can easily by extended to
cover other PM domain types, if/when needed.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For the multiple PM domain case, let's introduce a new function called
genpd_dev_pm_attach_by_name(). This allows a device to be associated with
its PM domain through genpd, by using a name based lookup.
Note that, genpd_dev_pm_attach_by_name() shall only be called by the driver
core / PM core, similar to how the existing dev_pm_domain_attach_by_id()
makes use of genpd_dev_pm_attach_by_id(). However, this is implemented by
following changes on top.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit fdb5c4531c ("bpf: fix attach type BPF_LIRC_MODE2 dependency
wrt CONFIG_CGROUP_BPF") caused some build issues, detected by 0-DAY
kernel test infrastructure.
The problem is that cgroup_bpf_prog_attach/detach/query() functions
can return -EINVAL error code, which is not defined. Fix this adding
errno.h to includes.
Fixes: fdb5c4531c ("bpf: fix attach type BPF_LIRC_MODE2 dependency wrt CONFIG_CGROUP_BPF")
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: Sean Young <sean@mess.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull x86 fixes from Thomas Gleixner:
- Prevent an out-of-bounds access in mtrr_write()
- Break a circular dependency in the new hyperv IPI acceleration code
- Address the build breakage related to inline functions by enforcing
gnu_inline and explicitly bringing native_save_fl() out of line,
which also adds a set of _ARM_ARG macros which provide 32/64bit
safety.
- Initialize the shadow CR4 per cpu variable before using it.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mtrr: Don't copy out-of-bounds data in mtrr_write
x86/hyper-v: Fix the circular dependency in IPI enlightenment
x86/paravirt: Make native_save_fl() extern inline
x86/asm: Add _ASM_ARG* constants for argument registers to <asm/asm.h>
compiler-gcc.h: Add __attribute__((gnu_inline)) to all inline declarations
x86/mm/32: Initialize the CR4 shadow before __flush_tlb_all()
Pull scheduler fixes from Thomas Gleixner:
- The hopefully final fix for the reported race problems in
kthread_parkme(). The previous attempt still left a hole and was
partially wrong.
- Plug a race in the remote tick mechanism which triggers a warning
about updates not being done correctly. That's a false positive if
the race condition is hit as the remote CPU is idle. Plug it by
checking the condition again when holding run queue lock.
- Fix a bug in the utilization estimation of a run queue which causes
the estimation to be 0 when a run queue is throttled.
- Advance the global expiration of the period timer when the timer is
restarted after a idle period. Otherwise the expiry time is stale and
the timer fires prematurely.
- Cure the drift between the bandwidth timer and the runqueue
accounting, which leads to bogus throttling of runqueues
- Place the call to cpufreq_update_util() correctly so the function
will observe the correct number of running RT tasks and not a stale
one.
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kthread, sched/core: Fix kthread_parkme() (again...)
sched/util_est: Fix util_est_dequeue() for throttled cfs_rq
sched/fair: Advance global expiration when period timer is restarted
sched/fair: Fix bandwidth timer clock drift condition
sched/rt: Fix call to cpufreq_update_util()
sched/nohz: Skip remote tick on idle task entirely
Keystone SOC driver update for 4.19
- Add suspend/resume functionality to TI EMIF SRAM driver
- Add wakeup M3 RTC self refresh support
- Fix for the PM runtime ifdefs
* tag 'soc_drivers_for_4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
soc: ti: wkup_m3_ipc: mark PM functions as __maybe_unused
soc: ti: wkup_m3_ipc: Add wkup_m3_request_wake_src
soc: ti: wkup_m3_ipc: Add rtc_only with ddr in self refresh mode support
memory: ti-emif-sram: Add resume function to recopy sram code
Signed-off-by: Olof Johansson <olof@lixom.net>
Alexei Starovoitov says:
====================
pull-request: bpf 2018-07-07
The following pull-request contains BPF updates for your *net* tree.
Plenty of fixes for different components:
1) A set of critical fixes for sockmap and sockhash, from John Fastabend.
2) fixes for several race conditions in af_xdp, from Magnus Karlsson.
3) hash map refcnt fix, from Mauricio Vasquez.
4) samples/bpf fixes, from Taeung Song.
5) ifup+mtu check for xdp_redirect, from Toshiaki Makita.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'clone' action to kernel datapath by using existing functions.
When actions within clone don't modify the current flow, the flow
key is not cloned before executing clone actions.
This is a follow up patch for this incomplete work:
https://patchwork.ozlabs.org/patch/722096/
v1 -> v2:
Refactor as advised by reviewer.
Signed-off-by: Yifeng Sun <pkusunyifeng@gmail.com>
Signed-off-by: Andy Zhou <azhou@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we end up with attempting to send packets from down devices
or to send oversized packets, which may cause unexpected driver/device
behaviour. Generic XDP has already done this check, so reuse the logic
in native XDP.
Fixes: 814abfabef ("xdp: add bpf_redirect helper function")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support to SLIMbus stream apis for slimbus device.
SLIMbus streaming involves adding support to Data Channel Management and
channel Reconfiguration Messages to slim core plus few stream apis.
>From slim device side the apis are very simple mostly inline with other
stream apis.
Currently it only supports Isochronous and Push/Pull transport protocols,
which are sufficient for audio use cases.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
